12.2 PROGRAMMING SECTION

Transcription

1 . PGAMMING SECTIN PC-

2 All programming of the V is done in the service mode as indicated in the following steps below. The main service modes are indicated in white text and the sub-modes are indicated in black text. Example: Time/Date Setting Mode Year Setting Month Setting Date Setting Hour Setting Daylight Saving Time PC-

3 FU-BUTTN PGAMMING All programming of the V- options is done in the service mode. To enter the service mode, open the vendor door and press and release the service mode button that is located on the control board. The first four selection buttons are used to navigate through the programming as follows: Button Description Usage Selection Button Abort Escape, Cancel Selection Button Up Increase, Next Selection Button Down Decrease, Previous Selection Button Enter K, Accept, Save The controller will automatically return to the open door sales mode if:. No information from the selection switches is received within approximately five minutes.. The service mode button is pressed a second time.. The (Abort) button is pressed.. The rtn function is activated. If the door is closed, the controller will exit the service mode and return to the sales mode. When the programming is entered, any established credit is returned to the customer. PC-

4 SET-UP AND CDE DESCIPTIN Error Display Mode If (Enter) is pressed at the prompt, the controller will enter the error display mode. If no errors have occurred, the display will show. If an error has been detected since the last error reset, the display will show the first error summary code that has occurred. EXAMPLE: would indicate (a column jam error). If (Enter) is pressed, the controller will display the detailed error for the summary code. Pressing (Up and Down) will cycle through any remaining error detail codes. If (Abort) is pressed while displaying any detailed code, the controller will return to the summary code. If (Abort) is pressed while displaying any summary code, the controller will return to the prompt. Note: See Error Code Map on next page Clearing an Error If (Enter) is pressed and held for two seconds during the display of the detailed error code, that error will be cleared. If other currently accessed detailed errors exist, the next error will now be displayed. If no other errors of this type exist, the next error summary code will now be displayed, or if no other errors exist. Coin Pay-out Mode If (Enter) is pressed at the prompt, the controller will enter the coin pay-out mode and display the lowest coin value that can be paid out (.5,.0,.5 etc.). The (Up or Down) selection buttons will allow the operator to cycle through the coin tube selections. If (Enter) is pressed, a pay out of the displayed value will be made. Coins will continue to pay out as long as (Enter) is held down. If (Abort) is pressed at any time, the controller will return to the prompt. EXAMPLE: If (Enter) is pressed while.05 is displayed, a nickel will be dispensed. Tube Fill Mode If (Enter) is pressed at the prompt, the controller will enter the coin tube fill mode. In this mode, the operator is allowed to deposit any coin into the coin changer s acceptor when that coin s tube is not full. The tube inventory level will be displayed after each coin is accepted. If (Abort) is pressed at any time during this operation, the controller will return to the prompt. PC-

5 Error Codes none UEnd CtrL SEL StS CHAr bual Crdr Ln rund S-d rfrg Summary level error codes (as displayed) Detail level error codes (as displayed) CJXX Column jam in column XX Complete a test vend cycle for column CS Chute sensor error Check or replace chute sensor assembly ds ran ACL SF IS Ib SLXX UAXX CC ts IC tjxx CrCH EE nj LA dis rout Description No errors exist Vend mechanism summary error Control system summary error ESC Escrow motor error Check or replace escrow motor assembly Door Switch AM check sum of service mode settings AC supply low Scale factor incompatibility Machine inlet chute sensor is blocked Machine inlet chute is blocked Selection switch summary error Selection switch error in switch XX Space-to-sales summary error Unassigned column for column XX Changer summary error No changer communication Tube sensor error Changer inlet chute blocked Tube payout jam in tube XX Changer M check sum error Excessive escrow attempts Coin jam Acceptance rate below 80% Disconnected acceptor Coin routing error Error codes are cleared by pressing the ENTE button for sec. when displayed or automatically by the following activities: CS Chute sensor error Check or replace chute sensor assembly Door Closed Change any service mode setting Scale factor corrected Blockage removed Switch opens Column is assigned Proper communication Changer corrected A coin is sensed Changer corrected Changer corrected A valid coin is sensed A coin is sensed Acceptance rate improves above 80% Acceptor properly connected Coin is routed properly Bill validator summary error bc No bill validator communication Proper communication bful Bill validator stacker full eceive stacker command bill Defective bill validator motor Validator becomes enabled bj Bill validator jam Validator becomes enabled brch Bill validator M check sum error Validator becomes enabled bpn Bill validator stacker is open or out of position Validator becomes enabled bs Bill validator sensor error Validator becomes enabled CrC CrXY C nc I ruc ru X SdC SdX Card reader summary error No card reader communication Card reader non-transient error: code X, sub-code Y n-line module summary error No on-line module communication No on-line network communication n-line module internal error emote vend mechanism (USD) summary error No communication with remote vend mechanism " " Error X from remote vend mechanism " " Selection/display device (ASD) summary error No selection/display device communication Error X from selection/display device Coin detected by changer Proper communication Error stops being reported Proper communication Proper communication esolved by LM Proper communication Device specific Proper communication Device specific efrigeration system summary error SEnS CLd Hot Temperature sensor defective or unplugged Cabinet temperature F below low limit Cabinet temperature F above high limit Sensor detected Temperature rises above low limit Temperature falls below upper limit CnPr Cooling system not cooling System cools F per hour Htr Heating system not heating System heats F per hour PC-5

6 SET-UP AND CDE DESCIPTIN (CNTINUED) Test Mode If (Enter) is pressed at the prompt, the controller will enter the test mode option. Upon entry into the test mode, the display will show the first summary test,. Pressing (Up or Down) will cycle through the available tests as listed below. Pressing (Enter) will enter the detailed test mode option. Pressing (Abort) while a summary test prompt is displayed will return the controller to the prompt. Test vend motor TEST PTINS Column jog test routine Test selection switch Test sold-out switches (reserved for future option) Check display/led Check compressor, fan, lights and heater relays Test Vend Motor If (Enter) is pressed at the prompt, the mode is displayed. If (Enter) is pressed at the prompt, the controller will enter the column vend test option. Upon entry into this setting the display will show. This will indicate that a test vend of column may be done. Pressing (Up or Down) will toggle through the available columns. Pressing (Enter) will test vend the displayed column. Pressing (Abort) will return the controller to the prompt. Column Jog Test outine If (Enter) is pressed at the prompt, the controller will enter the column jog test routine. Upon entry into this routine the display will show a message indicating that a jog test of column may be initiated. Using the (Up or Down) buttons will cycle through the available columns. Pressing the (Enter) button will display a message indicating the forward direction. Using the (Up or Down) buttons will toggle between (forward) and (reverse). Pressing the (Enter) button will initiate a jog test of the last displayed column in the last displayed direction. During the jog test, the direction of travel will remain indicated on the display. The motor will be activated and remain activated until the (Enter) button is released. The motor will continue in the direction of travel without regard to vend position until it reaches the stopping point on the coupling cam. Pressing (Abort) will return the controller to the prompt. NTE: Throughout the entire jog process, the motor will not be allowed to continue to a point or in a direction that would damage any part of the mechanism. PC-6

7 SET-UP AND CDE DESCIPTIN (CNTINUED) Selection Switch Test If (Enter) is pressed at the prompt, the controller will enter the selection switch test option. Upon entry into this setting the display will show. This indicates that the fourth button was pressed last. The last selection switch pressed will remain on the display until the service mode timer expires or the (Abort) button is pressed and held for two seconds. This will return the controller to the prompt. Sold-out Switch Test eserved for Future ption If (Enter) is pressed at the prompt, the controller will enter the sold-out test option. Upon entry into this setting the display will show. This indicates that column is not sold-out. If display shows this will indicate that the displayed column is sold-out. Pressing (Up or Down) buttons will toggle through the columns. Pressing (Abort) will return the controller to the prompt. EXAMPLE: 0 = Column is not Sold-out. = Column is Sold-out. Check Display/LED If (Enter) is pressed at the prompt, the controller will enter the display test option. Upon entry into this setting the display will toggle through all the vertical and horizontal display elements within each digit. The test will continue until the service mode timer expires or the (Abort) button is pressed. This will return the controller to the prompt. Check Compressor, Light and Heater elays If (Enter) is pressed at the prompt, the controller will enter the relay test option. Upon entry into this setting the display will show the state of the first component, This means the compressor is not activated and means the compressor is activated. Pressing (Enter) will toggle the state of the compressor. Pressing (Up or Down) will toggle through the available components as listed below. Pressing (Abort) will return the controller to the prompt. NTE: All components will be returned to their initial state, 0, upon the exit of this test routine. EXAMPLE: 0 = Means relay is de-activated. = Means relay is activated. CMPNENT LIST Controls the compressor Controls the evaporator fans Controls the lights Controls the heater option (optional kit) Note: Pressing (Enter) will return you to the. PC-7 prompt. Pressing (Up) will get you into

8 SET-UP AND CDE DESCIPTIN (CNTINUED) Password Protection will display only if the password has not been entered. The password is entered via the first four selection buttons while the controller is displaying. The password must be entered within 0 seconds in the following order: ---. The display will show a dash after the first selection button is pressed. After completing the sequence, press (Enter). If the password is not recognized, the display will remain blank. Cash Counter Display Mode If (Enter) is pressed at the prompt, the controller will enter the non-resettable cash counter mode by displaying. Pressing (Enter) will display cash total over the control board s life. A decimal will be displayed in the appropriate position. Pressing (Up or Down) will change the display to, which will give the card reader historical information. Pressing (Up or Down) again will change the display to / XXXX where N is a selection number and the XXXX will be replaced with the current re-settable cash amount. Using the (Up or Down) will cycle through the available selections. If (Abort) is pressed at anytime during this operation, the controller will return to the prompt. Vend Counter Display Mode If (Enter) is pressed at the prompt, the controller will enter the non-resettable vend counter display mode by displaying. Pressing (Enter) will display the number of all paid vends over the control board s life. Using (Up or Down) will cycle through each selection as / where the indicates the selection and the 0 s represent the resettable number of vends for that selection. A decimal will be displayed in the appropriate position. If (Abort) is pressed anytime during this operation, the controller will return to the prompt. Selection Price Setting Mode If (Enter) is pressed at the prompt, the controller will enter the selection price setting mode. The display will show if the machine is in multi-price mode, or if the machine is in single-price mode. In the multi-price mode, individual selection prices can be changed using the (Up or Down) to display where XX is the selection number, or choose to change the prices for all selection. If (Enter) is pressed, the display will show the current price for the displayed selection. Using (Up or Down) will increase or decrease the price. Holding (Up or Down) for more than five seconds will cause the price to change at 0 times the normal rate. While the desired price is on the display, press (Enter) and it will save that price. Pressing (Abort) will return to the selection level without saving the new price. PC-8

9 SET-UP AND CDE DESCIPTIN (CNTINUED) Depth Setting If (Enter) is pressed at the prompt, the controller will enter the depth setting programming mode by displaying X where X is the current depth setting. Using (Up or Down) will allow the operator to cycle through the available depth setting options (-). When one of the depth settings is on the display, pressing (Enter) will select that depth setting and return to the prompt. If one of the depth settings is displayed and (Abort) is pressed, the user will return to the mode without changing any settings. Space-to-Sale Programming Mode If (Enter) is pressed at the prompt, the controller will enter the space-to-sales programming mode by displaying X where X is the current option selected. Using (Up or Down) will allow the operator to cycle through the available space-to-sales options and. When one of the options,, is on the display, pressing (Enter) will select that space-to-sale option and return to the prompt. If one of the option is displayed and (Abort) is pressed, the user will return to the prompt without changing any settings. For proper configuration settings refer to the label located on the inner door shear panel. Custom Space-to-Sales Mode If (Enter) is pressed at the prompt, the controller will enter the custom space-tosales programming mode by displaying XX where XX is the current selection for that certain button, alternating with either indicating that no columns are assigned to the displayed selection button or the display will scroll through a sequence of numbers that represents the columns that are currently assigned to the selection button. Using (Up or Down) will cycle through all the available selections and then. You may also choose the option of clearing all space to sales settings by pressing (Enter) at the prompt. Pressing (Abort) will go immediately to the prompt, while pressing the (Abort) button will return the controller to the prompt without changing any settings. Pressing (Enter) while the prompt. is displayed will save all changes and return the controller to Pressing (Enter) while the XX prompt is displayed will allow columns to be assigned to the current selection. The display will show nn where nn is a column number. Using (Up or Down) will cycle through all the available columns. Pressing (Enter) at any column will enter the edit mode. The display will show nnx where X will either be flashing 0 (disabled) or (enabled) to assign the columns ( nn ) to the current selection. PC-9

10 SET-UP AND CDE DESCIPTIN (CNTINUED) Using (Up or Down) will change the assignment status of the columns. Pressing (Abort) will return the controller to the nn prompt without changing the status of the column, while pressing (Enter) saves the displayed status of the column before returning to the nn prompt. Pressing (Abort) at the nnx prompt returns the controller to the prompt. EXAMPLE: nn0 = The selection is disabled. nn = The selection is enabled. Machine Configuration Mode If (Enter) is pressed at the prompt, the controller will enter the machine configuration mode by displaying X which indicates configuration options number and the X is the current status of that setting. If X is then status is active, if X is 0 then the status is not active. If (Abort) is pressed while at the X prompt the controller will return to the prompt. Pressing (Up or Down) will toggle through the available configuration options. Pressing (Enter) saves the status of the current option and returns the user to the prompt. Pressing (Abort) returns the controller to the prompt without saving. (See Figure.) EXAMPLE: 0 = The Con is disabled. = The Con is enabled. Single/Multi-Price Mode Toggles between the single-price and multi-price modes. In the single-price mode, the price of selection will be used for all selections. In the multi-price mode, each selection can be set to a different price. 0 = Single pricing is used. = Multi-pricing is used. PC-0

11 SET-UP AND CDE DESCIPTIN (CNTINUED) CN# C C C C C5 C6 CNFIGUATIN SETTINGS DESCIPTIN PICE SETTING PTINAL FEATUES PS MESSAGE D PEN MIS MIS ESET ESEVED SETTINGS 0 = SINGLE PICE = MULTI PICE 0 = DISABLE PTINAL PGAM FEATUES = ENABLE PTINAL PGAM FEATUES 0 = DISPLAY PS MESSAGE = TUN FF PS MESSAGE 0 = DISPLAY SUMMAY E CDES = DISPLAY SUMMAY SALES DATA 0 = ESET MIS VIA DEX CMMAND NLY = ESET MIS WHEN D IS CLSED C7 C8 C9 C0 C SAVE CEDIT FCE VEND MULTI VEND BILL ESCW DEPTH LEANING 0 = SAVE CEDIT F 5 MINUTES = SAVE CEDIT INDEFINITELY 0 = NMAL VEND = FCE VEND 0 = SINGLE VEND = MULTI VEND 0 = ENABLE BILL ESCW = DISABLE BILL ESCW 0 = ENABLE = DISABLE Figure ptional Feature Enable This selection will allow optional features to be enabled and displayed in the current service mode menu. If any of the optional features described in this document are implemented, they must be able to be hidden by this selection. These features currently include,, and. 0 = ption is ff. = ption is n. PC-

12 SET-UP AND CDE DESCIPTIN (CNTINUED) LED Display Message Mode Toggles between the LED display modes. In the display/led mode, the current price will be displayed if in the single price mode. Note: will scroll when the option is set at 0. 0 = Display message is n. = Display message is ff. Door pen MIS Mode This option changes the pen-door Mode Display. If enabled, the total machine sales and total machine cash value are displayed before the error codes. These values represent the number of all paid vends and the cash amount of all paid vends, respectively. The sales and cash value are displayed the same as in the and service mode functions. The display shows / 0000 / 0000 for two seconds on the display/led, then / 0000 / 00.00, then or. If this option is disabled, existing errors are displayed, or for no existing errors. 0 = Existing errors or is displayed. = / 0000 / 0000 / 0000 / and or. MIS eset Mode This option is used to allow the door switch to reset all re-settable MIS. It will be reset only if the and mode were entered. 0 = All re-settable MIS registers will be reset only when the CF command is received from the HHC. = All re-settable MIS registers are reset when the door switch is activated if any of the re-settable MIS registers are read ESEVED F FUTUE PGAMMING. PC-

13 SET-UP AND CDE DESCIPTIN (CNTINUED) Save Credit Mode This option is used to determine how long credit should be maintained on the display and available to the customer. If Save Credit is enabled it will register the credit for no more than five minutes, after the vend is aborted and returns to standby. 0 = Clears credit in five minutes. = Credit remains. Force Vend Prevents the machine from making change without a selection being attempted. When this mode is enabled, escrow of coins is allowed until any of the following: A. Any bill is inserted into the bill acceptor; B. Any cash box coin (a coin that is not assigned to a tube) is inserted, or; C. The maximum vend price is reached. nce any of these conditions are met, an escrow request is ignored and a vend must be made. If a selection is made that is sold-out or locked out, this option will be overridden and an escrow request will be honored. NTE: Force vend has no effect on the card reader. nce a card is inserted, it can always be returned to the customer via an escrow or the return switch on the card reader. 0 = Force-vend is disabled. = Force-vend is enabled. Multi-Vend Allows multiple purchases without re-entering coins. If enabled, instead of returning the change after a vend, the credit will remain on the display to be used for another selection. An escrow will be honored at any time. This option will take precedence over the forcevend option after the first vend has been completed. 0 = Multi-vend is disabled. = Multi-vend is enabled. Bill Escrow Mode Allows the escrow of bills. If enabled and the bill value inserted takes the accumulated credit over the maximum price, the bill will be held in the escrow position. If the rule is disabled, bills will always go to the stacker. 0 = Bill escrow is disabled. = Bill escrow is enabled. PC-

14 SET-UP AND CDE DESCIPTIN (CNTINUED) Learning Mode Enable Allows the learning mode for depth setting to be used. If enabled, the learning mode will activate. If disabled, the learning mode will not be activated. 0 = Learning mode is disabled. = Learning mode is enabled. Correct Change nly Control Allows the customer to disable or enable the overpay routine. If If If If, Consumer overpay routine disabled for USA., Can be enabled for International use., Correct Change Value is the value that the controller has the ability to control the Use Correct Change nly option., Unconditional Acceptance Value is the largest value of any single form of currency that can be accepted without knowledge that the equivalent value of coins can be returned. This option applies to coins or bills. Preview Vend Password Setting Mode If (Enter) is pressed at the prompt, the controller will display the current password for the preview vend mode. The first digit of the number will be flashing. Pressing (Up or Down) will adjust the currently flashing digit up or down. Pressing (Enter) will save the currently flashing digit and the next digit of the password will begin flashing. All digits may be modified in this manner. Pressing (Enter) while the last digit is flashing saves the currently displayed password and return to the prompt. Pressing (Abort) at any time in the procedure returns to the prompt without saving. Change Language If (Enter) is pressed at the prompt, the controller will display the current language for the preview mode. Pressing (Up or Down) will toggle through the available languages listed below. Pressing (Enter) will activate the displayed language and return to the prompt. Pressing (Abort) at any time in the procedure returns to the controller to the prompt without changing the active language. PC-

15 SET-UP AND CDE DESCIPTIN (CNTINUED) LANGUAGE LIST English - mandatory if supported French - mandatory if supported German - mandatory if supported Italian - mandatory if supported Portuguese - mandatory if supported Spanish - mandatory if supported Slovene - mandatory if supported Time/Date Setting Mode If (Enter) is pressed at the (time) prompt, the controller will enter the time/date setting mode and display (disable) or (enable). Using (Up or Down) will allow the controller to cycle through all available time selection options. If (Abort) is pressed anytime during this operation, the controller will return to the prompt. TIME SELECTIN PTINS Enable/Disable time (Edit mode 0/) Current Year (Example 98) Current Date (month, day) Current Month Current Time (hours, minutes) Daylight Savings Time Year Setting ption If (Enter) is pressed at the prompt, the last two digits of the year are displayed and will be flashing. Pressing (Up or Down) will increase or decrease the year setting. Pressing (Enter) will save the displayed year setting and return the user to. Pressing (Abort) will return to without saving. Month Setting ption If (Enter) is pressed at the prompt, the controller will enter the month setting option. Upon entry into this option the display will show the current two-digit month setting, indicating the month of the year (example: 0-). Pressing (Up or Down) will increase or decrease the month setting. Pressing (Enter) will save the displayed month setting and return the Controller to the prompt. Pressing (Abort) while the month digits are flashing returns to the prompt without saving the month. PC-5

16 SET-UP AND CDE DESCIPTIN (CNTINUED) Date Setting ption If (Enter) is pressed at the prompt, the current two-digit date (days of the month) is displayed. Pressing (Up or Down) will increase or decrease the date setting. Pressing (Enter) will save the displayed date and return the user to the prompt. Pressing (Abort) while the date digits are flashing returns to the prompt without saving the new date. Hour Setting ption If (Enter) is pressed at the prompt, the current time is displayed in a -hour format. The left two digits of the display show the hour and the right two digits show the current minutes. While the hour digits are flashing, pressing (Up or Down) will increase/decrease the hour. Pressing (Enter) at this point will save the displayed hours and minutes and the digits will start to flash. While the minute digits are flashing, pressing (Up or Down) will increase/decrease the minutes. Pressing (Enter) at the point will save the displayed hours and minutes and return to the prompt. Pressing (Abort) while the hour or minute digits are flashing returns to without saving the hour or minutes. Daylight Saving Time If (Enter) is pressed at the prompt, the current daylight saving time option will be displayed. Using (Up or Down) will toggle the different countries; (Australian rules), (European rules), (No daylight savings) and (North American rules). If (Enter) is pressed at this point, the current display option will be saved and the user will be returned to the prompt. Pressing (Abort) returns to the prompt without saving. Light Control If (Enter) is pressed at the prompt the controller will enter the light control programming mode by displaying (disable) or (enable). Using (Up or Down) will allow the operator to cycle through all available time selection options. If (Abort) is pressed anytime during this operation, the controller will return to the code level. LIGHT CNTL PTINS Enable/Disable light timer (Edit mode 0/) Set start time Set days to time Set time to start ( hours) Set stop time PC-6

17 SET-UP AND CDE DESCIPTIN (CNTINUED) Set Enable/Disable If (Enter) is pressed at the X prompt, the last digit of the prompt will start flashing. Pressing (Up or Down) will toggle from (Enable) to 0 (Disable). Pressing (Enter) will save the displayed setting and return the user to X. Pressing (Abort) will return to X without saving. 0 = Setting is disabled. = Setting is enabled. Start Time Setting If (Enter) is pressed at the prompt, the controller will enter the start time setting option. Upon entry into this option the display will show. Pressing (Up or Down) will cycle through the available summary level codes. Pressing (Enter) will enter the detail level option. Pressing (Abort) while a summary level prompt is displayed will return the controller to the prompt. Pressing (Abort) at the prompt will return the controller to the prompt. Day Setting ption If (Enter) is pressed at the prompt, the current day of the week is displayed. The days are displayed as follows: X Monday X Tuesday X Wednesday X Thursday X Friday X Saturday X Sunday All Days 0 = Setting is disabled. = Setting is enabled. Pressing (Up or Down) at this point will rotate through the days of the week. Pressing (Enter) when a day (e.g. X) is displayed the X will start to flash by pressing (Up or Down) will toggle from 0 (disable) to (enable). If (Enter) is pressed, the displayed day is saved and the user is returned to prompt. Pressing (Abort) returns the controller to prompt without saving. PC-7

18 SET-UP AND CDE DESCIPTIN (CNTINUED) Start Hour Setting If (Enter) is pressed at the prompt, the current time is displayed in a -hour format. The left two digits of the display will show the hour and the right two digits show the current minutes. While the hour digits are flashing, pressing (Up or Down) will increase/decrease the hour. Pressing (Enter) at this point will save the displayed hours and minutes and the digits will start to flash. While the minute digits are flashing, press (Up or Down) to increase/ decrease the minutes. Pressing (Enter) at this point will save the displayed hours and minutes and return to the Prompt. Pressing (Abort) while the hour or minutes digits are flashing returns to without saving. Set Stop If (Enter) is pressed at the prompt, the controller will enter the stop time setting option. Upon entry into this option the display will show. Pressing (Up or Down) will cycle through the available summary level codes. Pressing (Enter) will enter the detail level option. Pressing (Abort) while a summary level prompt is displayed will return the controller to the prompt. Pressing (Abort) at the prompt will return the controller to the prompt. Note: To program days and hours refer to pages 7 and 8. efrigeration Control Mode If (Enter) is pressed at the prompt, the controller will enter the refrigeration control option by displaying X indicating the enable/disable setting mode. Using (Up or Down) will allow the operator to toggle between the following modes: EFIGEATIN CNTL PTINS Enable/Disable efrigeration timer (Edit mode 0/) Set start time Set days to time Set time to start ( hours) Set stop time Set days to time Set time to start ( hours) Temperature Setting If (Enter) is pressed at the prompt, the controller will enter the refrigeration control option by displaying X indicating the enable/disable setting mode. Using (Up or Down) will allow the operator to toggle between the following modes: PC-8

19 SET-UP AND CDE DESCIPTIN (CNTINUED) TEMPEATUE CNTL PTINS Set Temperature (Edit mode Fahrenheit/Celsius) Temperature set point (Factory setting 5 F.5 C) Storage temperature setting (Factory setting 60 F 5.5 C) PS temperature display (Edit mode 0/) Fan energy conservation mode (Edit mode 0/) Defrost control (Factory setting is enabled) Degree Setting If (Enter) is pressed at the X prompt, the controller will display X where X will be if the controller is currently in ºF (Fahrenheit) mode or if the controller is currently in ºC (Celsius) mode. Pressing (Up or Down) while the X digit is flashing will toggle the X digit between and. Pressing (Enter) will save the displayed temperature mode and return the user to the X prompt. Pressing (Abort) will return to the X prompt without saving. Set Point Setting (5ºF) If (Enter) is pressed at the prompt, the controller will display XX.XX where X will be the current set point temperature. Pressing (Up or Down) will increase/decrease by one degree increments. Pressing (Enter) will save the displayed temperature setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. Storage Temperature Setting (60ºF) If (Enter) is pressed at the prompt, the controller will display XX.XX where X will be the current storage temperature. Pressing (Up or Down) will increase/decrease by one degree increments. Pressing (Enter) will save the displayed storage temperature setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. PC-9

20 SET-UP AND CDE DESCIPTIN (CNTINUED) Display Temperature If (Enter) is pressed at the prompt, the controller will enter into the LED temperature display enable option. Upon entry into this option the display will show the current setting where the 0 is flashing will disable the temperature from being shown in the LED or if is flashing the temperature will be displayed in the LED following. Pressing (Up or Down) will toggle the digit between 0 and. Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. Fan Energy Savings If (Enter) is pressed at the prompt, the controller will display where X will be 0 or. When X is 0, The evaporator shall remain on at all times. When X is, the evaporator fan will turn off 5 minutes after the compressor turns off. When the compressor comes back on, so will the evaporator. Pressing (Up or Down) while the X digit is flashing will toggle the X digit between 0 and. Pressing (Enter) will save the displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. NTE: The mode will not function for hours from the pull-down start mode. Usage of this mode requires the installation of an optional evaporator relay. Defrost Setting If (Enter) is pressed at the prompt, the controller will display where X will be 0 or. If X is 0 and the compressor has been running for more than an hour and the temperature sensor input has not dropped at least F, the controller will turn off the compressor for a period of 0 minutes. Then the controller will change the defrost mode to. When X is, the controller will turn off the compressor for a period of 0 minutes (defrost cycle) at intervals of 6 hours, after the outer door is closed. Pressing (Up or Down) while the X digit is flashing will toggle the X digit between 0 and. Pressing (Enter) will save the displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. NTE: The model will not function for 7 hours from the pull-down start mode. PC-0

21 SET-UP AND CDE DESCIPTIN (CNTINUED) Block Selection Setting If (Enter) is pressed at the or prompt, the controller will enter the blocking control options. Upon entry into this routine the display will show the first summary level code. Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. Using (Up or Down) will let the operator toggle between the following modes: Note: blc or blc will not be accessible when C is set at 0. 0 = Block option is disabled. = Block option is enabled. BLCK CNTL PTINS Enable/Disable selection blocking (Edit mode 0/) Set start time Set days to time Set time to start ( hours) Set stop time Set days to time Set time to stop ( hours) Set selections Discount Setting Mode If (Enter) is pressed at the prompt, the controller will enter the discount control setting blocking control routine. Upon entry into this setting the display will show the first summary level code. If (Up or Down) is pressed it will cycle through the available summary level codes as listed below. Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. Using (Up or Down) will let the operator toggle between the following modes: Note: disc will not be accessible when C is set at 0. 0 = Disabled discount setting. = Enabled discount setting. BLCK CNTL PTINS Enable/Disable discount setting (Edit mode 0/) Set start time Set days to time Set time to start ( hours) Set stop time Set days to time Set time to stop ( hours) Set selections Set Discount amount PC-

22 SET-UP AND CDE DESCIPTIN (CNTINUED) Selection Setting If (Enter) is pressed at the prompt, the controller will enter the selection setting option. Upon entry into this setting the display will show the current setting for selection as, where shows it is enabled or 0 if the option is disabled. If (Up or Down) is pressed it will cycle through the valid selections or. Pressing (Enter) will save the currently displayed setting and return the controller to the prompt. Pressing (Abort) will return the controller to the prompt without saving. 0 = Selection setting is disabled. = Selection setting is enabled. Selection Setting If (Enter) is pressed at the prompt, the controller will enter the discount amount option. Upon entry into this setting the display will show the current four digit discount amount. If (Up or Down) is pressed it will increase or decrease the lowest discount amount. Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. ver-ide ption Mode (Units equipped with optional key switch) If (Enter) is pressed at the prompt, the controller will enter the over-ride option. Upon entry into this setting the display will show the first summary level code X. If (Up or Down) is pressed it will cycle through the available summary level codes as listed below. Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. Using (Up or Down) will let the operator toggle between the following modes: 0 = Disabled over-ride option. = Enabled over-ride option. Note: UEr will not be accessible when C is set at 0. VEIDE SETTING PTINS Enable/Disable free vend (Edit mode 0/) Enable/Disable no vend Selection blocking over-ride Discounting over-ride Lighting control over-ride efrigeration control over-ride PC-

23 SET-UP AND CDE DESCIPTIN (CNTINUED) ver-ide Free Vend If (Enter) is pressed at the prompt, the controller will enter the free vend enable option. Upon entry into this setting the display will show the current setting. Pressing (Up or Down) will toggle between 0 (disable) or (enable). Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. 0 = Disabled free vend. = Enabled free vend. ver-ide No Vend If (Enter) is pressed at the prompt, the controller will enter the no vend (vend over-ride) enable routine. Upon entry into this setting the display will show the current setting. Pressing (Up or Down) will toggle between 0 (disable) or (enable). While enabled, selections will not be allowed to vend and a message will be displayed. NTE: If both the free vend and no vend features are enabled, the no vend will be given priority. ver-ide Selection Blocking If (Enter) is pressed at the prompt, the controller will enter the selection blocking over-ride enable option. Upon entry into this setting the display will show the current setting. Pressing (Up or Down) will toggle between 0 (disable) or (enable). Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. 0 = Disabled selection blocking. = Enabled selection blocking. ver-ide Discount If (Enter) is pressed at the prompt, the controller will enter the discounting over-ride enable option. Upon entry into this setting the display will show the current setting Pressing (Up or Down) will toggle between 0 (disable) or (enable). Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. 0 = Disabled discount over-ride. = Enabled discount over-ride. PC-

24 SET-UP AND CDE DESCIPTIN (CNTINUED) ver-ide Lighting Control If (Enter) is pressed at the prompt, the controller will enter the lighting control override enable option. Upon entry into this setting the display will show the current setting Pressing (Up or Down) will toggle between 0 (disable) or (enable). Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. 0 = Disabled lighting control. = Enabled lighting control. ver-ide efrigeration Control If (Enter) is pressed at the prompt, the controller will enter the refrigeration control over-ride enable option. Upon entry into this setting the display will show the current setting. Pressing (Up or Down) will toggle between 0 (disable) or (enable). Pressing (Enter) will save the currently displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. 0 = Disabled refrigeration control over-ride. = Enabled refrigeration control over-ride. Selection Depth Setting If (Enter) is pressed at the prompt, the controller will display where X will be the number of products that can be loaded into the depth of the columns assigned to this selection. X can be,, or. Pressing (Up or Down) while the X digit is flashing will toggle the X digit between,, or. Pressing (Enter) will save the displayed setting and return the user to the prompt. Pressing (Abort) will return to the prompt without saving. emote Vend Mechanism eserved for future technology PC-

25 PGAMMING NTES PC-5

26 . WIING DIAGAM D C A C B I L N D E T SELECTIN SWITCHES DISPLAY SEL. # CM SEL. # SEL. # SEL. # SEL. # 5 SEL. # 6 SEL. # 7 SEL. # 8 N YEL BN VI N GY YEL BN VI SEL. # 9 (WHEN USED) N SEL. # 0 (WHEN USED) GY SEL. # (WHEN USED) YEL SEL. # (WHEN USED) BN SEL. # (WHEN USED) VI PNK PNK PNK PNK PNK BLU BLU BLU BLU BLU VI N ED VI J J BN N 5 5 BLU J ED N YEL VI GY PNK J J9 B B Y G L E K N L N N 6 MDB SCKET J9 G N N W 6 W W W W 5 W S C L T V C L S C L 0 T V C L S C L 9 T V C L S C L 8 T V C L VEC. (TADE). (CKE) CNTL BAD Y E L 6 5 B B L N K BALLAST MDE SWITCH ED JA DEX SCKET BLU LAMP ' BLU LAMP ' N N ELECTNIC BULB (CKE) J J8 8 GN 7 6 GN J6 /M9 9 M/YEL BLU/M M/VI M/GY M/PNK M5/ED M6/BN M7/N /CM 6 8 M8/TAN /DS J7 0 V/GY BN/TS HEATE/VI BN/TS /VSS SHIELD/VS /VSS SHIELD/VS TAN/TS CMP/BLU FAN/YEL LIGHTS/PNK TAN/TS 8 9 DS/ LAMP ' LAMP ' LAMP ' LAMP ' ED ED BLU BLU ED ED BLU BLU YEL YEL YEL YEL BALLAST ELECTNIC BULB (TADE) BN BN TAN TAN GN D CABINET CLD CABINET WAM GN C A W B A I N M E T PC-6

27 . WIING DIAGAM VEND MTS ( VDC) D C A C B I L N D E T B B B W B T B B B B B P B G B V B Y L L L H L A L L L E L N L L I L E K U K T K N K N K N K D K K K Y K K L MT # 0 (WHEN USED) MT # 9 MT # 8 MT # 7 MT # 6 MT # 5 MT # MT # MT # MT # (WHEN USED) /VSS SHIELD/VS /VSS SHIELD/VS VS VEND SENSS VS TYPICAL MT CICUIT WITH SLDUT PTIN CM SLDUT SWITCH NC T MT VDC GEA MT GN D YEL VI GY PNK ED BN N TAN BLU C A B I N E T /DS /DS /VS SHIELD/VS /VS SHIELD/VS GN PWE DIST. BX W A M N (7) VAC TANSFME PIMAY DS/ NC N D SWITCH (D PEN) CM DS/ TEMP SENS (HEATE PTIN) YEL () VI () BLU () GY () PNK (6) N (5) PNK VAC LIGHT ELAY TEMP SENS (EFIG.) CABINET CLD CABINET WAM GY GY YEL GY () YEL () FUSE 0.8 AMP SLW BLW BLU IBBED VAC GY CMP ELAY EVAP. FAN MT M PLAIN PTINAL FAN ELAY GY VI THEMAL VELAD GN L N G L N PTINAL HEATE PTINAL HEATE ELAY VAC VAC GY PLAIN HEATE ELEMENT IBBED VI PWE CD CND. FAN MT PLAIN IBBED CMP. PLUG M VELAD STAT ELAY CABINET CLD CABINET WAM CAPACIT (0 VLT UNITS NLY) EFIGEATIN SYSTEM PC-7

28 NTES. If the outer door is left open for over an hour, the lights and compressor will become active. In order to over-ride this option, press the door switch one time. PC-8