SCIA Engineer CADS RC Design Modules Link

Transcription

1 SCIA Engineer CADS RC Design Modules Link How to do batch processing

2 SCIA Engineer CADS RC Design modules link: How to do batch processing All information in this document is subject to modification without prior notice. No part or this manual may be reproduced, stored in a database or retrieval system or published, in any form or in any way, electronically, mechanically, by print, photo print, microfilm or any other means without prior written permission from the publisher. Scia is not responsible for any direct or indirect damage because of imperfections in the documentation and/or the software. Copyright 2008 Scia Group nv. All rights reserved.

3 Table of contents Batch design with CADS design modules... 1 Introduction... 1 Initial requirements for batch processing... 1 RC Beam Designer (RCBD) batch processing... 1 RC Column Designer (RCCD) batch processing... 4 RC Pad base Designer (RCPBD) batch processing... 7 RC Pilecap Designer (RCPCD) batch processing

4

5 Batch design with CADS design modules Batch design with CADS design modules Introduction This document describes the procedure to export and design reinforced concrete elements like beams, columns, padbases and pilecaps in batches from SCIA Engineer to CADS RC Design Modules. Initial requirements for batch processing 1. Create a structural model in SCIA Engineer with Concrete as material and BS or India as National code. 2. Define Ultimate and Serviceability load combinations. All the RC designers require ULS load combinations and RCPBD additionally requires SLS load combinations for design. 3. Define Result classes with both ULS and SLS selected (required only for designing RC Padbase) 4. Run the analysis. 5. Now you are ready to export the various RC components to the corresponding CADS RC Design applications using batch processing. RC Beam Designer (RCBD) batch processing Double click Concrete available in the Main tree. Select Beam designer under CADS BS design module. From the model select all or specific beams that need to be designed / exported. In the Properties palette set the selection to Current, set the type of loads to Combinations and select the required ULS combination. Click the >>> Export button available under Actions. 1

6 SCIA Engineer CADS RC Design modules link: How to do batch processing The following dialog will appear:- Select template or create new: A default template file will be displayed. By clicking the button (browse button) an existing template can be selected or using the New button a new template can be created. If the selected template is not found in the specified path (which might got deleted or moved to a different path), a warning message will be displayed and the default template will be used. Note that when there is a conflict between the template data and SCIA engineer data (eg concrete grade), the SCIA engineer data will be used. When the New button is clicked an instance of RCBD will open. After making necessary changes in the design parameters, save the blank job using the `save or `save as command to the desired path. Enter file name for saving the status report: A random unique file name will be given by the application to save the status report in RTF file format. Define a new file name if required. This file will be saved in the selected path for saving the batch jobs. Select path for saving RCBD batch jobs: A default path will be given by the application to store the batch jobs. Select an alternative path if required using the browse button available. Press OK to continue the batch process. The batch process will run in the background and the following dialog will be displayed after completing the batch process.

7 Batch design with CADS design modules Clicking View status report button will open the design summary report in RTF format in MS Word. The design summary report will have details like beam reference, span, size, concrete grade, bar details, status, warnings and error messages for each selected beam. Clicking Browse jobs will open the folder already specified in the initial batch process dialog where the RCBD batch jobs are stored. Clicking Browse jobs will also close the above dialog automatically. Note that unless the Batch Process dialog is closed the saved jobs can t be opened in CADS RC Beam Designer. Close button will close the batch process and go back to SCIA Engineer. Note that unless the above batch process dialog is closed you can t go back to SCIA Engineer. Note that the export is one way. No results will be displayed or used within SCIA Engineer. When the same set of beams are redesigned using the batch process a message will be displayed to warn that the existing jobs will be overwritten with a new set of jobs. Clicking Yes will result in overwriting the existing jobs. Clicking No will display the first batch process dialog to allow you to specify a different path for saving the batch jobs. After changing the path and clicking OK the batch process will be completed and the status report and batch jobs will be saved in the newly specified path. 3

8 SCIA Engineer CADS RC Design modules link: How to do batch processing RC Column Designer (RCCD) batch processing Double click Concrete available in the Main tree. Select Column designer under CADS BS design module. From the model select all or specific columns that need to be designed / exported. In the Properties palette set the selection to Current, set the type of loads to Combinations and select the required ULS combination. Click the >>> Export button available under Actions.

9 Batch design with CADS design modules The following dialog will appear:- Select template or create new: A default template file will be displayed. By clicking the button (browse button) an existing template can be selected or using the New button a new template can be created. If the selected template is not found in the specified path (which might got deleted or moved to a different path), a warning message will be displayed and the default template will be used. Note that when there is a conflict between the template data and SCIA engineer data (eg concrete grade), the SCIA engineer data will be used. When the New button is clicked an instance of RCCD will open. After making necessary changes in the design parameters, save the blank job using the `save or `save as command to the desired path. Enter file name for saving the status report: A random file name will be given by the application to save the status report in RTF file format. Define a new file name if required. This file will be saved in the selected folder for saving the batch jobs. Select path for saving RCCD batch jobs: A default path will be given by the application to store the batch jobs. Select the an alternative path if required using the browse button available. Press OK to continue the batch process. The batch process will run in the background and the following dialog will be displayed after completing the batch process. Clicking View status report button will open the design summary report in RTF format in MS Word. The design summary report will have details like column reference, size, concrete grade, bar details, status, warnings and error messages for each selected column. Clicking Browse jobs will open the folder already specified in the initial batch process dialog where the RCCD batch jobs are stored. 5

10 SCIA Engineer CADS RC Design modules link: How to do batch processing Clicking Browse jobs will also close the above dialog automatically. Note that unless the Batch Process dialog is closed the saved jobs can t be opened in CADS RC Column Designer. Close button will close the batch process and go back to SCIA Engineer. Note that unless the batch process dialog is closed you can t go back to SCIA Engineer. Note that the export is one way. No results will be displayed or used within SCIA Engineer. When the same set of columns are redesigned using the batch process a message will be displayed to warn that the existing jobs will be overwritten with a new set of jobs. Clicking Yes will result in overwriting the existing jobs. Clicking No will display the first batch process dialog to allow you to specify a different path for saving the batch jobs. After changing the path and clicking OK the batch process will be completed and the status report and batch jobs will be saved in the newly specified path.

11 RC Pad base Designer (RCPBD) batch processing Batch design with CADS design modules Double click Concrete available in the Main tree. Select Pad base designer under CADS BS design module. From the model select all or specific supports or support nodes that need to be designed / exported. In the Properties palette set the selection to Current, set the type of loads to Class and select a class having both SLS and ULS combinations. Click the >>> Export button available under Actions. 7

12 SCIA Engineer CADS RC Design modules link: How to do batch processing The following dialog will appear:- Select template or create new: A default template file will be displayed. By clicking the button (browse button) an existing template can be selected or using the New button a new template can be created. If the selected template is not found in the specified path (which might got deleted or moved to a different path), a warning message will be displayed and the default template will be used. Note that when there is a conflict between the template data and SCIA engineer data (eg concrete grade), the SCIA engineer data will be used. When the New button is clicked an instance of RCPBD will open. After making necessary changes in the design parameters, save the blank job using the `save or `save as command to the desired path. Enter file name for saving the status report: A random file name will be given by the application to save the status report in RTF file format. Define a new file name if required. This file will be saved in the selected folder for saving the batch jobs. Select path for saving RCPBD batch jobs: A default path will be given by the application to store the batch jobs. Select an alternative path if required using the browse button available. Press OK to continue the batch process. The batch process will run in the background and the following dialog will be displayed after completing the batch process. Clicking View status report button will open the design summary report in RTF format in MS Word. The design summary report will have details like pad base reference, size, concrete grade, bar details, status, warnings and error messages for each selected support. Clicking Browse jobs will open the folder already specified in the initial batch process dialog where the RCPBD batch jobs are stored. Clicking Browse jobs will also close the above dialog automatically. Note that unless the Batch Process dialog is closed the saved jobs can t be opened in CADS RC Padbase Designer.

13 Batch design with CADS design modules Close button will close the batch process and go back to SCIA Engineer. Note that unless the batch process dialog is closed you can t go back to SCIA Engineer. Note that the export is one way. No results will be displayed or used within SCIA Engineer. When the same set of bases are redesigned using the batch process a message will be displayed to warn that the existing jobs will be overwritten with a new set of jobs. Clicking Yes will result in overwriting the existing jobs. Clicking No will display the first batch process dialog to allow you to specify a different path for saving the batch jobs. After changing the path and clicking OK the batch process will be completed and the status report and batch jobs will be saved in the newly specified path. 9

14 SCIA Engineer CADS RC Design modules link: How to do batch processing RC Pilecap Designer (RCPCD) batch processing Double click Concrete available in the Main tree. Select Pile cap designer under CADS BS design module. From the model select all or specific supports or support nodes that need to be designed / exported. In the Properties palette set the selection to Current, set the type of loads to Combinations and select the required ULS combination. Click the >>> Export button available under Actions.

15 Batch design with CADS design modules The following dialog will appear:- Select template or create new: A default template file will be displayed. By clicking the button (browse button) an existing template can be selected or using the New button a new template can be created. If the selected template is not found in the specified path (which might got deleted or moved to a different path), a warning message will be displayed and the default template will be used. Note that when there is a conflict between the template data and SCIA engineer data (eg concrete grade), the SCIA engineer data will be used. When the New button is clicked an instance of RCPCD will open. After making necessary changes in the design parameters, save the blank job using the `save or `save as command to the desired path. Enter file name for saving the status report: A random file name will be given by the application to save the status report in RTF file format. Define a new file name if required. This file will be saved in the selected folder for saving the batch jobs. Select path for saving RCPCD batch jobs: A default path will be given by the application to store the batch jobs. Select an alternative if required using the browse button available. Press OK to continue the batch process. The batch process will run in the background and the following dialog will be displayed after completing the batch process. Clicking View status report button will open the design summary report in RTF format in MS Word. The design summary report will have details like pilecap reference, size, concrete grade, bar details, status, warnings and error messages for each selected support. Clicking Browse jobs will open the folder already specified in the initial batch process dialog where the RCPCD batch jobs are stored. Clicking Browse jobs will also close the above dialog automatically. Note that unless the Batch Process dialog is closed the saved jobs can t be opened in CADS RC Pilecap Designer. 11

16 SCIA Engineer CADS RC Design modules link: How to do batch processing Close button will close the batch process and go back to SCIA Engineer. Note that unless the batch process dialog is closed you can t go back to SCIA Engineer. Note that the export is one way. No results will be displayed or used within SCIA Engineer. When the same set of pilecaps are redesigned using the batch process a message will be displayed to warn that the existing jobs will be overwritten with a new set of jobs. Clicking Yes will result in overwriting the existing jobs. Clicking No will display the first batch process dialog to allow you to specify a different path for saving the batch jobs. After changing the path and clicking OK the batch process will be completed and the status report and batch jobs will be saved in the newly specified path. Notes 1. Any time during batch process if you happen to switch to other windows the above dialog may hide behind the screen. Use alt+tab keys to select the dialog and bring it to the front of screen.