F-117 Quick Start Users Guide after Installing Software:

Transcription

1 F-117 Quick Start Users Guide after Installing Software: Please read all information in this guide and refer to it often. This material is only intended to provide initial instructions about the basics of turning your device on, understanding its features/functions and daily use. Technical support offered by the distributor is for questions about the mechanics of the device. Technical support does not include instruction about the medical use of the device nor to give medical advice. Care of Device: Front Bulbs connectors must be plugged in at all times. Do not run machine without the bulb plugged into the machine, as it will result in damage to the internal components. Always place unit on a hard surface. Do not run True Focus, True Silver, or Ion Pro Wave programs on the bulb. These may damage your machine if you do. The machine will blow the fuses if these program folders are run on the bulb. Do not allow bulb cords to cross more than twice or feedback errors may occur.

2 F-117 TrueRife Machine: Back of Machine: Fuses and Transistors Child Safety Toggle Switch Must be in Up Position Power Cord USB Cord Flip the silver toggle switch in bottom corner UP. It is a child safety switch that should always stay in the up position. If the switch is flipped down, then the program will not run. There is extra transistor and fuses on the back of the machine.

3 Front of F-117 TrueRife Machine: #1 Power #2 Output Control Turn Clockwise #3 Bulb Toggle #4 L.E.D. indicators- green for power, red for rife program (red light blinks or stays solid depending on frequencies) #5 Bulb #6 Accessory Toggle 1. Power button- do not turn on until bulbs are plugged into the machine 2. Output Control Knob- Turn the knob all the way clockwise. It should always stay in this position. The Upper Room sends the rife home with the knob in the correct position. 3. Bulb Toggle Switch- flip the red toggle switch to BULB. It should always stay in this position. Please note: If you switch the toggle to the bath position and run a program for the bulb, you could damage the unit. (note: you do not have the apparatus for the bath) 4. L.E.D. indicators- These lights are only indicators and do not impact the functioning of the machine. The green light indicates that the power is on. The red light indicates that the rife program is running. The red light will stay steady or may flash at different intervals as it runs the rife programs. 5. Bulb outputs: Plug the bulb cords into this spot- red to red and black to black 6. Accessory toggle switch-this toggle can be on the COLOR or LED because it is only used for accessory items.

4 Setup: Computer Power Cord Rife Power Cord 1. Plug power cords from computer and RIFE into a SURGE PROTECTOR. Power surges can cause damage to the transistor and/ or the fuse and if you do NOT use a surge protector, your warrantee is void. Surge Protector 2. Plug the other end of the computer power cord into the computer (it will only fit into 1 socket) to keep it AC powered at all times. Computer Power Cord 3. Plug the silver cord coming out of the Rife (called a USB cable) into the computer (there are multiple USB sockets on the computer and you can plug into any of them). USB Cable Power must be off while plugging bulbs into machine and taking them out! 4. Take the RIFE bulb and plug the cord with the red end into the red socket and the black end into the black socket, above the words Bulb Outputs, on the front of the RIFE. Make sure to always plug the bulb in before turning the power on the RIFE machine also, turn the power off the RIFE machine before unplugging the bulb.

5 Daily Use: 1. Turn the computer and the RIFE to on. 2. When computer is finished starting up, double click on the True Rife icon on the main screen of the computer.

6 Open Home Tab 3. When the F100 program comes up, single click on Open Home. Your file will be listed first 4. When the TrueRife Frequencies folder comes up, double click on the folder with AA_Your Name. (We wrote the programs in this folder specifically for you)

7 Double click on night program 5. When the folder with your name comes up, double click on the correct night program. Click once on RUN to start program 6. Now that you ve opened the program that you want to run, single click on Run to start the program running. Then close the computer screen down. It is as simple as this. 7. Single click Pause while the program is running if you need to take a short brake. If you desire to start again, you must click Pause again to start. ( Pause to pause and Pause again to start from a pause)

8 Click once on STOP to stop program 8. Single click Stop if you need to stop the program. If you click Run again, it will start from the beginning. General True Rife File: 1. Complete steps 1-3 above. 2. When the True Rife Frequencies folder comes up (what should be the Home screen), you will see the list of files with your folder first. The general True Rife files are listed below your folder in alphabetical order. These are programs that can be used for general issues.

9 Rife Control Panel Instructions: 1. The RIFE control panel has the following buttons: Open Home, Run, Stop, Pause, Hold, Skip, Memorize, Links, Update Freqs, Repeat. The buttons that you will need daily are Open Home, Run, and Stop. Pause, Links, and Update Freqs. will be used occasionally. Hold, Skip, Memorize, and Repeat generally are not used. a. Open Home: This button will open the complete list of RIFE files b. Run: click on this button to run the program c. Stop: click on this button to stop the program d. Pause: click on this button to pause the program for a short time e. Hold: click on this button to hold the frequency f. Skip: click on this button to skip the current frequency that is running on the program g. Memorize: do not click on this button h. Links: click on this button to be linked to a website for additional information on a standard RIFE program. Your laptop must be connected to your home wifi in order to connect to the internet. i. Update Freqs: click on this button to update the standard frequencies from True Rife. Your laptop must be connected to your home wifi in order to connect to the internet. This should be done a couple of times a year. This will not impact any of the programs that Dr. Conners created. j. Repeat: click on this button to repeat the program that is running. 2. The buttons on the bottom of the screen are used for scanning and will not be used during daily use. 3. The blue portion of the screen will indicate the current frequency, the total amount of time for the program and how much of the program has been completed.

10 Trouble shooting: Please note that feedback can happen at any time and impact the communication between the computer and Rife. The rife will complete the program even if the communication to the computer has been impacted. Due to this, it is important that you close the computer screen after starting the program. While the program is running, an error window pops up but the RIFE continues to run. 1. Do not do anything while the RIFE is running. The machine will run by itself once it is started by the computer. 2. When the RIFE stops, simply turn the RIFE machine off. 3. Close the error window and the F100 program if it does not do it by itself. 4. Start over at Daily Use step 1. You click on run and a window pops up showing, Did not detect generator. Did you install USB Driver? 1. Turn RIFE off and back on again. 2. Wait a couple seconds and try single clicking Run again. 3. If this does not work, repeat step 1 and add: unplug the USB cable from the computer and re-plug it back into the computer. 4. Wait a couple seconds and try single clicking Run again. 5. I have had to do steps 3 and 4 a couple of times before the program will start correctly. While the RIFE is running, you see the message come up on the status line, Can t open USB specified in properties. See solution for Trouble shooting A or do the following: 6. You do not need to stop or pause the RIFE machine. 7. Unplug the USB cable and plug it back in while the RIFE is running. 8. The message should go away but may come back at any time. This message does not change the program currently being run. So, if it keeps reoccurring just let the RIFE machine run until the program is finished. 9. When the RIFE machine stops, single click Stop on the computer. 10. Then proceed to Daily Use step 3. You click Run and the program is running but the RIFE Bulb is not. 1. Shade the bulb to make sure the faint light the bulb is making is strong enough for you to see in the current light. It is common, if the program is running on a high frequency that you will NOT see any apparent light transmitting from the bulb. It is still working! You can also try single clicking Skip a couple of time to see if you can see some of the other frequencies in the program. 2. If there is definitely NO light coming from the bulb, single click Stop. 3. Unscrew the black knob on the back of the RIFE labeled Fuse. 4. Check the fuse to see if the wire in the middle is broken. If it is discard the fuse and replace it. (There should be some taped to the back of the RIFE) 5. Screw the Fuse knob into the back of the RIFE until it is snug. 6. Single click Run again. 7. If the fuse was the problem, it may be a good idea to plug the unit into an outlet strip that acts as a barrier to voltage changes. Additional fuses should be ordered from TrueRife. If you should purchase new fuses locally, they should be 4 Amp quick blow fuses. If you are still having trouble check please call TrueRife ( ) for additional assistance.