PDU - Overview / Non-Intelligent PDU s

Size: px

Start display at page:

Download "PDU - Overview / Non-Intelligent PDU s"

Noah Casey
5 years ago
Views:

1 PDU - Overview / Non-Intelligent PDU s InfraPower Rack Power Distribution Units InfraPower Rack PDU Range Switched (Outlet kwh PDU) Monitored (kwh PDU) Metered Basic WSi WS W MD Basic Outlet Measurement Outlet Switch ON / OFF Latching Relay kwh Measurement Hot-pluggable Meter 2.8 Touchscreen DC Module SNMP Hardware Sensor Port x 2 (Temp & Humidity) 16 x PDU in Single Daisy Chain One IP Access 16 x PDU Levels Aggregate Amp Measurement Local Ammeter Voltage: 110V / 208V / 250V Basic Power Distribution Units (PDU s) Cost efficient and reliable rack mount power distribution units which simply deliver / distribute power from outside the rack to the I.T. equipment.» Horizontal or Vertical form factors» Multiple outlet configuration in one PDU» Full custom configurations available» Coloured PDU casings and cords» Resettable fuse or Hydraulic MCB options» Surge protector or EMI filter options» Basic PDU s available in Single or Three Phase Metered (MD) Power Distribution Units (PDU s) MD Series PDUs allow true RMS current local monitoring via a digital RMS ammeter. The blue LED display is easy-to-read from a distance and allows rapid access to the aggregate load on the circuit. It easily prevents circuit overloads during equipment installation and allows users to plan the capacity based on actual real time current monitoring. Blue LED indicator also allows easy local reading of current, especially when there is no lighting installed inside the rack.» Dual Feed Metered PDU s available 3

2 Intelligent kwh PDU / W Series W Series Intelligent PDU s» Monitored (W) PDU Intelligent PDU with digital local touchscreen display and IP network connectivity for reporting the entire strip data.» Metered & Outlet Switched (WS) PDU A rack mount PDU which has the above Monitored (W) functionality in addition to IP network connectivity to enable users to switch or control individual outlets or IT equipment within the cabinet.» Outlet Switched with Outlet Metering (WSi) PDU A rack mount PDU with IP network connectivity that allows users to switch individual outlets and meter individual outlet or equipment consumption. Field Replaceable Digital Local Touchscreen Display A field replaceable RMS current meter with 2.8 colour LCD display with touch screen functionality. The field replaceable display design helps eliminate maintenance downtime by simply replacing a possible defective meter without a service interruption. For increased visibility and ease of access the display is positioned at the top of the PDU. High Metering Accuracy» The sharp and highly visible display of the colour LCD provides local data of:» Current (AMP)» Voltage (Volt)» Power (KW)» Energy Consumption (kwh)» Power Factor of entire PDU» This data has a metering accuracy to within +/- 1%. Single or Three Phase W Series Intelligent PDU s are available in 3-Phase. Phase voltage balance, Custom configurations available. Multiple Outlet Configurations Multiple outlet configurations per each individual PDU e.g. One vertical PDU with 2xUK, 20xC13, 4xC19 outlets. Coloured PDU Power Feed Differentiation The use of colours at the intelligent rack PDU and cord level has become a huge market trend with most organisations favouring different colours in the cabinet for the A & B or primary and redundant feeds into equipment. PDU chassis available in: Black / White / Blue / Red / Yellow / Green / Orange / Purple. Field Replaceable DC Module Given the mission critical nature of the environment the intelligent rack PDU is designed, built and manufactured to provide extremely high levels of resiliency. In addition to the hot swappable digital local touchscreen display, field replaceable DC power modules are used within the Metered & Outlet Switched (WS) PDU and the Outlet Switched with Outlet Metering (WSi) PDU models to avoid unnecessary downtime. Circuit Breakers» Protected load segments for increased reliability» Overload switch» Designed with fully shrouded protective cover to prevent accidental ON / OFF operation Environmental Sensors The module features 2 x environmental plug in ports for temperature and humidity monitoring. The most typical sensors usually combine Temperature & Humidity allowing users to significantly reduce the number of required network data ports and IP addresses at the rack level. IP Dongle (SNMP) Hot pluggable IP dongle provides IP remote access to the PDUs using a single IP Address chain. Only 1 x IP dongle is required to access a maximum of 16 x PDUs in a daisy chain. Latching Relays To protect mission critical equipment from unplanned downtime, socket switching is controlled via bistable / latching relays. Ensuring an always on operational performance and socket status returning to a pre-power outage after a planned or unplanned shutdown. Power consumption during normal/standard operation is low and therefore assists to reduce energy usage of the overall PDU. Thermal Resettable Fuse» PDUs are available with the option of individually fused IEC outlets, to help prevent an overload of the active equipment and avoiding short circuiting the entire IEC outlet PDU.» Protected load segments for increased reliability» Overload reset button Cost effective solution for safety operation. 4

Intelligent kwh PDU / W Series Functions & Features Vertical Button Mounting Kit» Quick and tool-less

mounting holes on rear verticals Vertical Bracket Mounting Kit» Universal mounting kit supports all cabinet

bottom entry power feed as standard» Customisation to top feed entry is available Three Phase PDU s» InfraPower

» Free IPM-04 Management Software Fused IEC Outlet PDU W Series PDUs are available with the option of

disconnection. It is compatible to generic IEC cords and hence cost saving in locking cables.

C19» UK BS1363» Schuko» US NEMA Operating Parameters The operating parameters for intelligent PDUs should take

is still increasing due to growing power consumption.

3 Intelligent kwh PDU / W Series Functions & Features Vertical Button Mounting Kit» Quick and tool-less integration simplifies PDU installation» Designed for third party global branded racks with key hole type mounting holes on rear verticals Vertical Bracket Mounting Kit» Universal mounting kit supports all cabinet models» Easy integration by mounting the PDU to the cabinet cable tray Power Feed Entry» InfraPower PDUs have bottom entry power feed as standard» Customisation to top feed entry is available Three Phase PDU s» InfraPower 3-Phase PDUs with phase voltage balance.» Multiple socket configurations available per PDU.» Free IPM-04 Management Software Fused IEC Outlet PDU W Series PDUs are available with the option of individually fused outlets, to help prevent an overload of the active equipment and avoiding short circuiting the entire IEC outlet PDU. Lockable IEC Outlet PDU Lockable IEC Outlet PDU models are available to secure plugs and prevent accidental disconnection. It is compatible to generic IEC cords and hence cost saving in locking cables. Socket Types InfraPower PDUs available with socket configurations to your requirements including:» IEC C13» IEC C19» UK BS1363» Schuko» US NEMA Operating Parameters The operating parameters for intelligent PDUs should take into account the temperature rise within the rack due to the exhaust air from servers / storage equipment which is still increasing due to growing power consumption. These temperatures are also compounded by the overall rising data centre temperatures.» Operating Temperature: -5 to 60 o C» Storage Temperatures: -25 to 65 o C» Operating Altitude: 0 to 2,000 m» Storage Altitude: 0 to 15,000 m» Humidity: 8 to 95% RH (non-condensing) Reach a Power Expert sales@austin-hughes.eu +44 (0)

Intelligent kwh PDU / W Series High Density PDU Remote Management Reduces IP Address Costs within the Network IP Dongle and Daisy Chain With any rack mount device or in-cabinet PDU one of the largest

» For IP PDU access simply connect 1 x IP dongle» 1 x IP dongle allows access to 16 x PDU» Only 1 x IP for 16 x PDU access InfraPower W Series PDUs have the ability to cascade at least 16 PDU s to

managed internally, this typically represents huge cost savings to organisations.

4 Intelligent kwh PDU / W Series High Density PDU Remote Management Reduces IP Address Costs within the Network IP Dongle and Daisy Chain With any rack mount device or in-cabinet PDU one of the largest challenges is to integrate the device into the data centre environment without simply building up additional connectivity, cable run, patch panel etc. or network related costs.» For IP PDU access simply connect 1 x IP dongle» 1 x IP dongle allows access to 16 x PDU» Only 1 x IP for 16 x PDU access InfraPower W Series PDUs have the ability to cascade at least 16 PDU s to one master IP Dongle or address, this in turn reduces cost as only one data network port per sixteen PDU s is required and as most IT managers will tell you only one IP address needs to be issued and managed internally, this typically represents huge cost savings to organisations.» Patented design» Hot pluggable for easy integration» Highly cost-effective method to access the intelligent PDUs» SNMP Capability v2 / v3» Daisy Chain by Cat5/6 cable» Maximum distance between 2 PDU s is 20 meters Vertical PDU IP Dongle AHAPDUIPD02S Horizontal PDU IP Dongle AHAPDUIPDH02S IP Dongle on the first PDU level Daisy chain by Cat5 / 6 cable 6

Intelligent kwh PDU / W Series Management Software Ultra-high density PDU Management can be achieved with InfraPower Manager, the associated software for W Series Intelligent PDU s.

IPM-04 provides the basic functions of:» Monitoring of measurement of Amps, Volts, kw, kwh, power factor and temperature/humidity» Remote switching ON/OFF per individual power outlets» Reporting»

5 Intelligent kwh PDU / W Series Management Software Ultra-high density PDU Management can be achieved with InfraPower Manager, the associated software for W Series Intelligent PDU s. Supporting remote management of multiple PDU daisy chain groups. IPM-04 provides the basic functions of:» Monitoring of measurement of Amps, Volts, kw, kwh, power factor and temperature/humidity» Remote switching ON/OFF per individual power outlets» Reporting» Alarm setting» PDU outlet measurement» Grouping and chart reporting Capacity Enhanced Features Basic Features PDU Series Support Features IP Dongle Group (Just 1 for 16 PDU levels) 50 PDU Number 800 Concurrent Users 5 Outlet Scheduling Apparent Power (kva) Monitoring Power Factor Measurement Circuit Breaker (MCB) Monitoring Aggregate Current (Amp) Monitoring Individual Outlet Switch ON / OFF Temperature / Humidity Monitoring Rising Alert Threshold Remote Access via Web Graphic User Interface Free IPM-04: 50 x IP Groups 800 x PDU s 5 x Concurrent User 3rd Party DCIM (via SNMP): Cost-efficient PDU management can be achieved by applying IP dongle & daisy chain SNMP Capability v2 / v3 7

6 Intelligent kwh PDU / W Series Field Replaceable PDU W3 Meter The field replaceable display design helps eliminating maintenance downtime by simply replacing a possible defective meter without a service interruption. No power downtime is required. The connection ports for the PDU daisy chain as well as the temperature and humidity sensors are conveniently positioned for easy access.» 2.8 colour LCD with touchscreen functionality» Sharp and highly visible display» Field replaceable» Local metering» Ports for external Sensor / Display connection» PDU daisy chain via IP Dongle» Single Phase / Three Phase PDUs available 1 Phase 3 Phase Local Management by Meter Display for PDU Monitoring» Amp, Volt and Power Factor» kwh Energy Consumption» Active and Apparent Power» Temperature and Humidity Display for Outlet Level Measurement (Wi and WSi Series PDUs only)» Outlet Amp» Outlet kwh Display for Local PDU Setting» PDU Level» Meter Buzzer» Meter Screen» PDU Outlet ON *If optional Temperature / Humidity Sensors connected 8

7 Dual Feed Intelligent kwh PDU / W Series W Series Intelligent Dual Feed PDU s» Two PDUs by One Chassis & Meter» 2.8 Colour LCD Meter with Touchscreen» Field replaceable DC module, redundant embedded 2nd DC module» Facilitates Rack Cabling» Simplify Dual PDU Setup» Save Your Rack Space» Reduce IP Address Cost» Increase Management Efficiency Monitored (W) PDU Intelligent PDU with digital local touchscreen display and IP network connectivity for reporting the entire strip data. Metered & Outlet Switched (WS) PDU A rack mount PDU which has the above Monitored (W) functionality in addition to IP network connectivity to enable users to switch or control individual outlets or IT equipment within the cabinet. Outlet Switched with Outlet Metering (WSi) PDU A rack mount PDU with IP network connectivity that allows users to switch individual outlets and meter individual outlet or equipment consumption. Two PDU s in One Chassis W series Dual Feed PDU is designed to house two PDUs in a single chassis which only requires one side installation. Facilitating PDU setup and saving valuable rack space. Users also benefit from the Red + Blue coloured layout to distinguish the primary and redundant (A&B) power feeds. One Meter Supports Two PDUs Sophisticated LCD touchscreen meter is integrated into single chassis but allows local monitoring for both PDUs. (also supports up to 16 cascade levels). With the addition of the IP dongle only 1 x IP is required to access up to 32 PDU s in a single cascaded group the primary and redundant (A&B) power feeds. Facilitates Cable Management Separating power and data cables inside a rack minimises erratic data transfer as well as EMI and assists in distinguishing between power and data cabling. One Side Orientation for Power Cabling Power and data cables should be kept apart in order to avoid interference. It is a typical practice to isolate power cabling to one side of the rack, whether it is for primary or secondary power connection. InfraPower Dual Feed PDU series offers an efficient, convenient and space saving solution - Primary and Secondary PDUs are integrated to one unit with dual power feed. Free Management Software (IPM-04)» 50 x IP Groups» 800 x PDU s» 5 x Concurrent User» 3rd Party DCIM (via SNMP) 9

Accessories / Part Code Builder PDU Part Code: * ** * ** * ** * * Please select from the following opons to create the PDU you require Socket Type 1 Socket Type 2 Socket Type 3 Socket Socket Socket

Sockets 12 12 16 If no C13 sockets 7 = 16A If none required insert 20 16 000 required insert 18 000 20 28 Example PDU Conguraon AH030103111 Ausn Hughes ercal PDU xu 0xC13 xc19 sockets 1A Si 3 lead

8 Accessories / Part Code Builder PDU Part Code: * ** * ** * ** * * Please select from the following opons to create the PDU you require Socket Type 1 Socket Type 2 Socket Type 3 Socket Socket Socket Socket Type Socket Type 2 Socket Type 3 AH 02 Sockets = C19 IEC Sockets 2 = 16A If no C19 sockets required insert 10 7 = NEMA Sockets = 20A 12 8 = CEE7/5 Schuko Sockets If no C13 sockets 7 = 16A If none required insert required insert Example PDU Conguraon AH Ausn Hughes ercal PDU xu 0xC13 xc19 sockets 1A Si 3 lead 0309 Commando Plug oon fed power input lack A 900 V Accessories IP Dongle Patented hot pluggable IP Dongle provides IP remote access to the PDUs by a true network IP address chain. It is designed to support daisy chain connections allowing up to 16 PDUs to be cascaded via Cat6 cables - all the PDUs are remotely accessed via a single network IP address.» Hot pluggable for easy integration» Cost effective method to access the intelligent PDUs» Allows IP remote access to the PDUs by a single network IP» SNMP capability AHAPDUIPD02S AHAPDUIPDH02S IP Dongle - Vertical IP Dongle - Horizontal External Door Mount PDU Display External door mount PDU display provides a highly visible local display without the need to open the rack rear door to read the PDU(s) information.» RJ-11 port x 2 for PDU Amp and Temperature monitoring» Display will connect back to each IP PDU via door and 3M RJ-11 cable» Once connected, reading of PDU Amps and temperature shows in the external door mount display AH-WS-DIS01 External PDU Display Accidental Release Sleeves IEC One of the simplest areas of providing resiliency is reducing accidental cord removal at the IEC equipment cord level, by using IEC C13 or C19 Sleeves. power cable requires 12Kg of force to remove. IEC_C13 IEC_C19 C13 Cord Sleeve C19 Cord Sleeve 10

Accessories / Part Code Builder * * * * * Model Type Cord Length Input Plug Feed Input Chassis Colour Extra Requirments 0 = Basic 1 = 1 Meter 1 = Black RAL 9005 1 = Circuit Breakers L = LSZH input

= Transfer Switch 7 = WSi 6 = 6 Meter 6 = Residual Current D = Dual Feed PDUs 7 = 7 Meter 7 = L6-20P Nema Plug 8 = Orange RAL 1007 Monitoring (RCM) Don t Forget!

9 Accessories / Part Code Builder * * * * * Model Type Cord Length Input Plug Feed Input Chassis Colour Extra Requirments 0 = Basic 1 = 1 Meter 1 = Black RAL = Circuit Breakers L = LSZH input cord 1 = MD 2 = 2 Meter 2 = Top 2 = Blue Pantone 200c 2 = Individually Fused E = External Earth Cord Supplied S = Special Requirement 5 = Wi 6 = WS 5 = 5 Meter 5 = Unterminated 5 = Yellow RAL 1018 T = Transfer Switch 7 = WSi 6 = 6 Meter 6 = Residual Current D = Dual Feed PDUs 7 = 7 Meter 7 = L6-20P Nema Plug 8 = Orange RAL 1007 Monitoring (RCM) Don t Forget! All W Series PDUs 8 = 8 Meter 9 = Green RAL 6029 require 1 x IP 9 = 9 Meter Dongle per 16 For Coloured IEC Sockets cascaded PDUs 0 = 10 Meter please contact Ausn for remote Hughes management Watch the InfraPower Intelligent PDU Video austin-hughes.eu/pduvid.php Sensors» External Sensors available for Temperature/Humidity.» Low profile design with magnetic base for easy affixing to the rack.» A pair of sensors can be connected to one single W series PDU meter. AH-IG-T012M AH-IG-T014M AH-IG-TH012M AH-IG-TH014M Temperature Sensor, 2M Temperature Sensor, 4M Temperature & Humidity, 2M Temperature & Humidity, 4M Coloured Locking Equipment» Locking Equipment Cords (Please note - Not socket locking)» Provide the simplest way to enhance cable management and visualise power sources.» Colours: Black, Blue, Red» Lengths: 1M, 2M, 3M C13-C14 Cords AHA AHA AHA AHA AHA AHA AHA AHA AHA C13-C14 Black 1M C13-C14 Black 2M C13-C14 Black 3M C13-C14 Blue 1M C13-C14 Blue 2M C13-C14 Blue 3M C13-C14 Red 1M C13-C14 Red 2M C13-C14 Red 3M C19-C20 Cords AHA AHA AHA AHA AHA AHA AHA AHA AHA C19-C20 Black 1M C19-C20 Black 2M C19-C20 Black 3M C19-C20 Blue 1M C19-C20 Blue 2M C19-C20 Blue 3M C19-C20 Red 1M C19-C20 Red 2M C19-C20 Red 3M Custom Configurations available on short lead-times sales@austin-hughes.eu / +44 (0)

Automatic Transfer Switch / Metered Automatic Transfer Switches (ATS) - Metered» 1U and 2U Metered (MD) Automatic Transfer Switches Power Redundancy for Single Corded Devices Power downtime or

However, some network devices and entry-level servers are not designed with power redundancy.

If the primary source becomes unavailable, it switches to the secondary power source seamlessly. Local Amp Monitoring by Meter InfraPower ATS allows true RMS local Amp measurement via a digital meter.

10 Automatic Transfer Switch / Metered Automatic Transfer Switches (ATS) - Metered» 1U and 2U Metered (MD) Automatic Transfer Switches Power Redundancy for Single Corded Devices Power downtime or disruption is never acceptable for data centre equipment. It is common for mission critical devices to apply primary and secondary power sources. However, some network devices and entry-level servers are not designed with power redundancy. For single corded equipment, Austin Hughes InfraPower ATS is perfectly fit to provide dual power sources (primary and secondary). If the primary source becomes unavailable, it switches to the secondary power source seamlessly. Local Amp Monitoring by Meter InfraPower ATS allows true RMS local Amp measurement via a digital meter. Blue LED display is easy-to-read from a distance and allows rapid access to the aggregate load on the circuit. It prevents circuit overloads during equipment installation and allows the users to plan the capacity based on actual real time current monitoring. Efficient Redundancy for Multiple Single Fed Power Devices InfraPower ATS with outlets provide power distribution features. One ATS cost effectively provides power redundancy to multiple pieces of critical equipment. InfraPower offers ATS rack mount models with 8 to 20 IEC / NEMA outlets. Custom configurations available on request. Input Preference Switch The InfraPower ATS includes an input preference switch allowing Users to set the power source preference to supply the output. Specifications Electrical Nominal Input Voltage Acceptable Input Voltage Input Frequency Outlet Connectors Local Meter Transfer Time Physical Product (W x D x H) 1U Packing (W x D x H) Net Weight Gross Weight Product (W x D x H) 2U Packing (W x D x H) Net Weight Gross Weight Chassis Colour Chassis Materials ±10% nominal 1 x 10-amp circuit breaker for 1 x 16-amp circuit breakers for Approx. 8VA 5.1kg / 11.2lb Black Steel 12

Intelligent Automatic Transfer Switch / W Series Automatic Transfer Switches (ATS) - Monitored» 1U and 2U Monitored (W) Automatic Transfer Switches Input Switching Locally or Remotely Over IP Local

11 Intelligent Automatic Transfer Switch / W Series Automatic Transfer Switches (ATS) - Monitored» 1U and 2U Monitored (W) Automatic Transfer Switches Input Switching Locally or Remotely Over IP Local power input switching is essential, especially for conducting maintenance in the data centre. Alternatively, InfraPower intelligent ATS enables users to switch power input over IP, saving manpower and providing a prompt way to switch power input. Remote Monitoring Over IP InfraPower Intelligent ATS provides a real time monitoring on Amp, Volt and kwh.helping Users with capacity planning and improving the overall power efficiency of the data centre. InfraPower Intelligent ATS offers 3 types or remote management to select from:» InfraPower ATS-04 Free Download» InfraPower GUI Built-in» 3rd Party DCIM via SNMP Power Redundancy for Single Corded Devices Intelligent ATS are ideal for network devices and entry-level servers that are not designed with power redundancy. Austin Hughes InfraPower ATS provides dual power sources (primary and secondary). If the primary source becomes unavailable, it switches to the secondary power source seamlessly. Remote Management Over IP ATS-04 GUI SNMP No. of ATS Supported 50 1 Concurrent Users 5 1 Input Switching Over IP x x x x x x x x Apparent Power (kva) Monitoring x x Power Factor Measurement x x Voltage (Volt) Monitoring x x Aggregate Current (Amp) Monitoring x x Circuit Breaker Monitoring x x Alarm Alert x x x rd Party DCIM Specifications Electrical Nominal Input Voltage Acceptable Input Voltage Input Frequency Outlet Connectors Local Meter Transfer Time Physical 1U ±10% nominal Product (W x D x H) Packing (W x D x H) Net Weight Gross Weight Product (W x D x H) 2U Packing (W x D x H) Net Weight Gross Weight Chassis Colour Chassis Materials Schuko / FR Outlets Field Replaceable 1.8 Colour LCD 1 x 16-amp circuit breaker for C20 / 1 x 20-amp circuit breaker for Open-end 5.1kg / 11.2lb Black Steel 13

PDU. InfraPower POWER AUSTI AUSTIN AUSTIN AUSTIN 3 PHASE WSI WI WS W MD BASIC. Enclosure Power Management Solutions

PDU. InfraPower POWER AUSTI AUSTIN AUSTIN AUSTIN 3 PHASE WSI WI WS W MD BASIC. Enclosure Power Management Solutions PDU A AUSTI POWER 3 PHASE WSI WI WS W MD BASIC Temperature & Humidity Sensors A pair of sensors can be connected to one single W series PDU meter. 3 PHASE Free Management Software Manager enhances the