BoxLED DS Plus (Double Side) BX-DS-PL; BX12BA-W4F Signage Lighting System INSTALLATION GUIDE
|
|
- Myrtle Barnett
- 6 years ago
- Views:
Transcription
1 BoxLED DS Plus (Double Side) BX-DS-PL; BX12BA-W4F Signage Lighting System INSTALLATION GUIDE WARNING: ONLY QUALIFIED PERSONNEL SHOULD PERFORM INSTALLATION TO AVOID ELECTRICAL SHOCK OR COMPONENT DAMAGE, DISCONNECT POWER BEFORE PERFORMING INSTALLATION OF THE POWER SUPPLIES, MODULES, AND/OR RGB CONTROLLERS. Failure to install the power supplies and/or LED modules in accordance with the National Electric Code (NEC), all applicable Federal, State, and local electric codes as well as the specific Underwriters Laboratories (UL) safety standards for the installation, location and application may cause serious personal injury, death, property damage and/or product malfunction. These instructions are guidelines for installation of LED modules and power supplies. Installation requirements may vary depending on the application. Licensed electricians should provide all installation services for connection for both primary and secondary (input/output) of the power supplies. RETROFIT SIGN CONVERSION LED KIT FOR USE ONLY IN ACCORDANCE WITH KIT INSTRUCTIONS E SNE 1.0 PREPARE FOR INSTALLATION 1.1 Tools Required: - Wire stripper/cutter - Screwdriver - Measuring tape 1.2 Supplies Required: - PLTC cable - Wire nuts/connectors - #8 screws or rivets - Accessory Mounting Track and Brackets 1.3 Carefully remove existing neon or fluorescent tubes, HID or incandescent light sources and power supplies and/or ballasts if necessary Make sure power is turned off. a. Where applicable, determine if a disconnect switch needs to be installed (may be integral with existing power supply/transformer) Remove all existing screws, sockets and wiring Dispose of all old sign components in the proper manner Repair and seal any unused openings in the sign enclosure. Openings greater than ½ diameter require a metal patch secured by screws or rivets and caulked with nonhardening caulk. Smaller openings may be sealed with non-hardening caulk Clean the inside of the sign to make sure it is free of dirt. LED340
2 2.0 MECHANICAL INSTRUCTIONS 2.1 Refer to desired module layout 2.2 Measure inside cabinet dimensions Required track lengths
3 2.4 Cut the two b track segments to length be certain the dimension d on both track pieces is the same to ensure the tracks are parallel in the case 2.5 Attach the two b track segments to the sides of the case
4 2.6 Examples of module spacing
5 2.7a Insert BoxLED Plus DS modules into the required number of a track pieces referring to step 2.6 for layout options 2.7b Insert one end of the module into the track and push down on the opposite end until it clicks into place 2.8 Loop any excess wire around the track in-between the modules and tie wrap it into place
6 2.9 Slide the Left and Right mounting brackets onto the corresponding ends of each of the a track segments 2.10 Slide the assembly into the desired mounting holes in the b track segments and push down on the left and right brackets so they click into place
7 3.0 ELECTRICAL INSTRUCTIONS 3.0 Use wire nuts or connectors to connect the white and red (+) input wire of the modules to the red (+) output wires of the 24V power supply. Connect the black and white (-) input wire of the modules to the blue (-) output wire of the 24V power supply (see Figure 11). 3.1 Cap off any unused connection wires when finished. 3.2 Make sure AC line is OFF before beginning power supply installation. Secure power supply to clean metal surface using screws (see Figure 12). Figure 11 Figure OPTIONAL AC DISCONNECT SWITCH INSTALLATION: Connect disconnect switch in line with VAC line (black wire) (see Figure 13). VAC into Disconnect isconnect Switch Optional Disconnect Switch VAC out from Disconnect Switch Figure 13 Figure Finish power supply AC connection by connecting black VAC line to black input cord of power supply, and white neutral to white input cord of power supply. Connect green ground wire from line to the same metal surface the power supply is mounted on (see Figure 14).
8 3.5 Power Supply Information: Table 1 Power Supply Information Item Number Ordering Description Power Supply Wattage Input Voltage (VAC) Input Current (A) Output Voltage (V) OT50W/24V/120V/LP 50W OT75W/24V/UNV 75W 120/ / OT96W/24V/UNV 96W 120/ / Table 2 Max. Number of Modules per Power Supply BX-DS-PL (73502, 73737) BX12BA-W4F (71920) Item Number Ordering Abbreviation Max. Modules per Power Supply OT50W/24V/120V/LP OT75W/24V/UNV OT96W/24V/UNV Troubleshooting Guide Problem Possible Cause Corrective Action Entire sign does not light No input power Check AC connection to power supply. Check power supply connection to modules. Entire sign/one or more LED runs do not light Part of an LED run does not light One module does not light No power to LED modules No power to that run Module has been damaged Check DC polarity- power supply red output wires must be connected to red striped module wires, power supply blue output wires must be connected to black striped module wires. Verify power supply output voltage is 24V. Check module to module connection for correct polarity. Replace the module. Observe correct polarity. Specifications subject to change without notice OSRAM, BoxLED, and OPTOTRONIC are registered trademarks of OSRAM GmbH SYLVANIA is a registered trademark of OSRAM SYLVANIA Inc. SEE THE WORLD IN A NEW LIGHT is a trademark of OSRAM SYLVANIA Inc OSRAM SYLVANIA Inc. 02/16
PEREGRINE SERIES RETROFIT INSTALLATION GUIDE
06.05.17 HanleyLED H100W-PPS524V Spec Sheet SOLUTIONS THAT MAKE SENSE PEREGRINE SERIES RETROFIT INSTALLATION GUIDE Light Up New Markets Your Local Distributor: Grimco US www.grimco.com 800.542.9941 Canada
More informationCHANNEL LETTER LIGHTING UNIQUE LIGHTING SOLUTIONS RETROFIT INSTALLATION GUIDE
UNIQUE LIGHTING SOLUTIONS LIGHTING WARNING -Installation must only be performed by a licensed electrician. -To prevent death, injury or damage to property this product must be installed in accordance to
More informationOSRAM ReliaSys TM D15 LED Retrofit Kit INSTALLATION GUIDE
www.osram-americas.com S90655 OSRAM ReliaSys TM D15 LED Retrofit Kit INSTALLATION GUIDE OSRAM ReliaSys TM Outdoor LED Retrofit Kit is an alternative to high-intensity discharge (HID) lamps up to 400W (MH)
More informationOT DMX RGB Installation Guide
www.sylvania.com OT DMX RGB Installation Guide This installation guide outlines the stepby-step instructions to properly install and configure the OT DMX RGB control interface with a DMX controller. This
More informationWARNING. General Information
Principal LED Sign Retrofit Installation Manual Kit Model: PL RT1 001 WARNING Retrofit Installation must only be performed by qualified personnel in accordance with the National Electric Code in the USA
More informationPrincipal LED Street Stik Fluorescent Bulb Replacements
Principal LED Street Stik Fluorescent Bulb Replacements LED Retrofit Guide (PL-RT1-001) WARNING Installation must only be performed by a licensed electrician. To prevent death, injury or damage to property
More informationPrincipal LED Qwik Stik Fluorescent Bulb Replacements
Principal LED Qwik Stik Fluorescent Bulb Replacements LED Retrofit Guide (PL-RT1-001) WARNING Installation must only be performed by a licensed electrician. To prevent death, injury or damage to property
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationSignBOX II. Retrofit Guide for (X)WS201 and (X)WD201
Scope: This procedure is designed to aid in the installation of SloanLED s SignBOX II illumination product and power supply products. Skilled tradespeople familiar with general construction, electrical
More informationM215 (M215-60) Safety
M215 QUICK INSTALL GUIDE M215 (M215-60) Safety Important Safety Information This document contains important instructions to use during installation and maintenance of the Enphase M215 Microinverter. To
More informationM250 (M LL) Safety
M250 SAFETY M250 (M250-60-2LL) Safety Important Safety Information This document contains important instructions to use during installation of the Enphase M250 Microinverter. To reduce the risk of electrical
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationTECHKNOW, INC. Kiosk Order Confirmation System INSTALLATION MANUAL. Revision Date: July 11, 2012 Part # Version 3.2
document Page 1 of 18 TECHKNOW, INC Kiosk Order Confirmation System INSTALLATION MANUAL Revision Date: July 11, 2012 Part # Version 3.2 Techknow, Inc. 393 Mayfield Road Duncan, SC 29334 www.gotechknow.com
More informationPreparing for a Docking Drawer Slim Installation To prepare for a successful Docking Drawer Slim installation please ensure that the cable management
Docking Drawer Install Manual Docking Drawer Slim Series Applicable Models: 0290 00031(W) / 24 0290-00030(W) / 21 0290-00047(W) / 18 0230-00004. r6 1/19/2016 CAUTION READ CAREFULLY Failure to follow these
More informationPrevaLED Troffer. Snap board feature allows for customizable lengths. Light is OSRAM.
www.osram.us/ds PrevaLED Troffer Snap board feature allows for customizable lengths The PrevaLED Troffer LED module family offers innovative solutions for a variety of LED troffer luminaires with its customizable
More informationEnphase S-Series Microinverter and Engage Cable Safety
SAFETY Enphase S-Series Microinverter and Engage Cable Safety Important Safety Information (S280-60-LL and S230-60-LL) This document contains important instructions to use during installation of the Enphase
More informationInstalling a Power over Ethernet injector
Installing a Power over Ethernet injector AlphaEclipse StreetSmart and RoadStar signs The instructions in this document explain how to install/replace a Power over Ethernet (PoE) injector in a StreetSmart
More informationWARNING ELECTRICAL SHOCK HAZARD
Description Safety Instructions The top-entry sub D9 connector kit is designed for enclosure sizes D1h D8h, E1 E2, and E1h E4h with VLT PROFIBUS DP MCA 101 option. It fits the following drives: VLT HVAC
More informationInk-Dot Series II Driver
Instruction Sheet P/N 766B Ink-Dot Series II Driver Introduction See Figure. Ink-Dot Series II controllers can have from one to three driver modules. Any existing controller can easily be retrofit with
More informationOutdoor PTZ. Mounting on the Ceiling Using Pendant Mount. Installation Guide. For Models: I93, I94, I95, I96, KCM /12/03
Outdoor PTZ Mounting on the Ceiling Using Pendant Mount For Models: I93, I94, I95, I96, KCM-8211 2013/12/03 Table of Contents Mounting Solutions... 3 Straight Tube Installation Procedures... 4 Step 1:
More information527F Dual PC Option Installation Guide as replacement for 32MP made by Fadal
527F Dual PC Option Installation Guide as replacement for 32MP made by Fadal Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 Phone: (818) 357-5826 www.calmotion.com 2006-2013 Calmotion LLC, All rights
More informationM215-Z Safety Information (M LL-IG-ZC)
M215-Z SAFETY M215-Z Safety Information (M215-60-2LL-IG-ZC) This document contains important instructions to use during installation of the M215-Z Zep Compatible Microinverters. To reduce the risk of electrical
More informationM215 Safety (M LL-S22-IG / S23-IG / S24-IG)
M215 SAFETY M215 Safety (M215-60-2LL-S22-IG / S23-IG / S24-IG) Important Safety Information This document contains important instructions to use during installation of the Enphase M215 Microinverter. To
More informationAdapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout
Installation Instructions Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout Catalog Numbers 2711-NR5T, 2711P-RAT12E2 Topic Page About This Publication 1 Important User Information 2 About
More informationCatalog Number Identification with Elements Explained V V V V X 347 V Hz
Owner s Manual 917 & 918 Remote Control Switches TABLE OF CONTENTS page Ratings & Installation... 1 2 Optional Accessories... 3 4 Troubleshooting & Parts Kits... 5 Wiring & Outline Diagrams... back of
More informationOperating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
More informationSAVE THESE INSTRUCTIONS
OUTDOOR HARDWIRE INSTALLATION INSTRUCTIONS Please read and save these instructions. Read carefully before using product. Protect yourself and others by observing all safety information, warnings and cautions.
More informationInstallation Guide SMT 2200/3000 VA Input/Output Hardwire Kit
Installation Guide SMT 2200/3000 VA Input/Output Hardwire Kit Important Safety Messages SAVE THESE INSTRUCTIONS - This section contains important instructions that should be followed during installation
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Uni-I/O Modules Installation Guide UIS-04PTN Uni-I/O is a family of Input/Output modules that are compatible with the UniStream control platform. This guide provides basic installation information for
More informationTwisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Supplement to Operation & Service Manual
Twisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Supplement to Operation & Service Manual Document Part #: 040-0271-01 Rev. C Your cabinet has a new design with a Sintra Marquee, stand-alone
More information810D Series FAA L-810 Double Obstruction Light Installation Manual
810D Series FAA L-810 Double Obstruction Light Installation Manual 2562426A REV. A 708 Printed in U.S.A. i Contents Safety Message to Installers, Users, and Maintenance Personnel... 1 Overview... 2 Unpacking
More informationInstallation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2
1 Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2 Tsubis Part Number: LCD12-0046 Power Down 1. Power down the controller. 2. Power down the complete machine by turning off the rear
More informationInstallation and Operations Manual. Electronic copies available at (Rev_ )
Installation and Operations Manual Electronic copies available at www.aquariitech.com/downloads/axceleronmanual Axceleron Installation and Operations Manual AXCELERON FIXTURE INSTALLATION... 1 Introduction...
More informationPowerLogic High Density Metering System 1-Meter Enclosure
PowerLogic High Density Metering System 1-Meter Enclosure Installation Guide 63230-508-211A1 Safety information PowerLogic High Density Metering System 1-Meter Enclosure Important information Read these
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationReplacing the Power Supply
APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools
More informationAnswer Modular Power. Page 1 of Rev V. Power Kits. Change of Height Harness. Receptical Covers
Answer Modular Power Change of Height Harness Power Kits Receptical Covers NOTE: Unused modular electrical connector openings are not required to be capped. NOTE: The electrician can cut conduit and wire
More informationUSBCNC USB Disk Key reader for CNC Controls Machine Mount instructions
USBCNC USB Disk Key reader for CNC Controls Machine Mount instructions 2008-2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 www.calmotion.com Introduction This
More informationMCG Surge Protection
299-700-33B 299-700-33A MCG Surge Protection Installation/Operating Instructions for MCG 500 Series Important Warranty Information MCG surge protectors are designed to work at specific voltages and configurations,
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Uni-I/O Modules Installation Guide UID-0808R, UID-0808T, UID-1600,UID-0016R, UID-0016T Uni-I/O is a family of Input/Output modules that are compatible with the UniStream control platform. This guide provides
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationLINEARlight FLEX Accessories
www.osram.us/flexlighting LINEARlight FLEX Accessories LED Modules Key Features & Benefits Easy assembly without soldering wires Assembly without tools Reduced assembly time Highly shock resistant These
More informationPV Rapid Shutdown device
PV Rapid Shutdown device Installation and Operation Manual Solis-RSD-1G(1:1) Solis-RSD-1G(2:2) Manufacturer: Ginlong (Ningbo) Technologies Co.,Ltd., Ningbo, Zhejiang, P.R.China US Office: 565 Metro Pl.
More informationLinearray PD Retrofit Kit
Linearray Retrofit and Installation Instructions 1. Scope All Installations should be performed by qualified personnel and all electrical work should be performed in accordance to NEC and local code. These
More informationPANEL MOUNT INTERCOMS
PANEL MOUNT INTERCOMS INSTALLATION AND SERVICE INSTRUCTIONS FOR MODELS AD-26P, AD-27P, AD-56P, and AD-57P Address all communications and shipments to: Electrical Products Division 2645 Federal Signal Drive
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Uni-I/O Wide Modules Installation Guide UID-W1616R, UID-W1616T Uni-I/O Wide is a family of Input/Output modules that are compatible with the UniStream control platform. Wide Modules are 1.5 times as wide
More informationPXC Compact Unitary Equipment Controller (UEC)
Document No. 553-169 PXC Compact Unitary Equipment Controller (UEC) Product Description The PXC Unitary Equipment Controller (UEC) is an MS/TP device that can be configured as a programmable, stand-alone
More informationInstallation Instructions
50ES, 50EZ, 50GL, 50GS, 50GX, 50JS, 50JX, 50JZ, 50SD, 50SZ, 50VL, 50VT, 50XP, 50XZ 601A, 602A, 602B, 604A, 604B, 604D, 607C, 701A, 702A, 702B, 704A, 704B, 704D, 707C PA1P, PA2P, PA3P, PH1P, PH2P, PH3P
More informationSeries 3700 Screw Terminal Assemblies Installation Instructions
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY www.keithley.com Series 3700 Screw Terminal Assemblies Installation Instructions Introduction This document contains handling
More informationExpressCard Instant Issuance Card Personalization System Ethernet Jack Replacement Procedure. September 22, 2014
ExpressCard 2000 Instant Issuance Card Personalization System Ethernet Jack Replacement Procedure September 22, 2014 Manual Part Number: 99875721-1.01 REGISTERED TO ISO 9001:2008 MagTek I 1710 Apollo Court
More informationQuick Start. This document describes how to install the Juniper Networks PTX5000 Packet Transport
PTX5000 Packet Transport Router Quick Start September 2017 Part Number: 530-066788 Revision 01 This document describes how to install the Juniper Networks PTX5000 Packet Transport Router. Contents Quick
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Uni-I/O Modules Installation Guide UIA-0402N Uni-I/O is a family of Input/Output modules that are compatible with the UniStream control platform. This guide provides basic installation information for
More informationOperating Instructions
Operating Instructions Model Numbers: LS LS M LS G LS A LS LS 00 LS M-WC LS A LS X LS M-WC LS B LS X LS M LS Dimensions A / B / C / D / E 0 / F / Electrical Information Voltage AMPS Frequency 0 HZ Single
More information-Verify that supply wiring voltage matches power supply voltage by comparing it with power supply label.
WARNING! RISK OF FIRE OR ELECTRICAL SHOCK Disconnect power before installing or servicing. WARNING: Risk of fire or electrical shock. Luminaire wiring, power supply, or other electrical parts may be damaged
More informationStandard icontrol Power Supply Kit
Instruction Sheet P/N 07150A Standard icontrol Power Supply Kit This instruction sheet is a guide for upgrading to the Standard icontrol Power Supply. WARNING: Allow only qualified personnel to perform
More informationIntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures)
IntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures) Installation and User s Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Uni-I/O Modules Installation Guide UID-0808THS Uni-I/O is a family of Input/Output modules that are compatible with the UniStream control platform. This guide provides basic installation information for
More informationREMOTE HEAD ADAPTER INSTALLATION GUIDE
REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and
More informationThis guide provides basic information for Unitronics Models 230/260/280/290 (Non-color Screens).
Vision OPLC Installation Guide Models 230/260/280/290 (Non-color Screens) This guide provides basic information for Unitronics Models 230/260/280/290 (Non-color Screens). General Description Vision OPLCs
More informationOperating instructions AS-i SmartLine module AC3200 AC /00 06/2016
Operating instructions AS-i SmartLine module AC3200 AC3201 80237876/00 06/2016 Contents 1 Preliminary note...3 1.1 Symbols used...3 1.2 Warnings used...3 2 Safety instructions...3 2.1 General...3 2.2 Target
More informationCAUTION READ CAREFULLY
DOCKING DRAWER INSTALL MANUAL, 0230-00004 Rev 2 7/1/15 Applicable Models: 0290-00030, 0290-00031 JTech Solutions, Inc. 12893 Alcosta Blvd. Ste M San Ramon, CA 94583 www.jtechsolutions.us CAUTION READ CAREFULLY
More informationAutoScan to MultiScan Replacement Kit
Instruction Sheet P/N AutoScan to MultiScan Replacement Kit WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other
More informationINSTALLATION INSTRUCTIONS
Wired Remote Controller 7 Day Programmable Ductless Systems KSACN0401AAA (High Wall Models) KSACN0501AAA (Ducted/Cassette Models) INSTALLATION INSTRUCTIONS NOTE: Read the entire instruction manual before
More informationDocumentation. AL225x Connector-Box. Accessory for servo drives of the series AX5000 and AX2000. Version: Date:
Documentation Accessory for servo drives of the series AX5000 and AX2000 Version: Date: 1.8 2018-01-16 Contents Contents 1 Foreword... 5 1.1 Notes on the documentation... 5 1.2 Documentation Issue Status...
More informationGPIB-232CT-A IBCL EPROM Installation Guide
NATIONAL INSTRUMENTS The Software is the Instrument Installation Guide GPIB-232CT-A IBCL EPROM Installation Guide This guide describes how to replace the factory-installed EPROM that comes with your GPIB-232CT-A.
More informationInstruction Manual. M Pump Motor Controller. For file reference, please record the following data:
Instruction Manual M Pump Motor Controller For file reference, please record the following data: Model No: Serial No: Installation Date: Installation Location: When ordering replacement parts for your
More informationInstallation Guide V290 (Color) This guide provides basic information for Unitronics LCD color touchscreen models V C30B and V T40B.
Vision OPLC Installation Guide V290 (Color) This guide provides basic information for Unitronics LCD color touchscreen models V290-19-C30B and V290-19-T40B. General Description Vision OPLCs are programmable
More informationBroadband Automatic Disconnect Switch. User Manual
Reset/Test Primary/ Primary Broadband Automatic Disconnect Switch User Manual Local Power Remote Pwer Local 63V Fault Secondary Select Secondary 220V Normal 990-1929 09/2004 Introduction Introduction
More informationModel 2460-KIT. Screw Terminal Connector Kit. Description / September 2014 *P * 1
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.keithley.com Model 2460-KIT Screw Terminal Connector Kit Description The Model 2460-KIT Screw Terminal Connector Kit
More informationTRC-190 User s Manual
User s Manual Edition 3.2, May 2017 www.moxa.com/product 2017 Moxa Inc. All rights reserved. User s Manual The software described in this manual is furnished under a license agreement and may be used only
More informationIntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures) Installation and User s Guide
IntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures) Installation and User s Guide *619751* P/N 619751 - Rev B IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS
More informationOPLC Installation Guide
Samba OPLC SM35-J-R20/SM43-J-R20 SM70-J-R20 SM35-J-T20/SM43-J-T20 SM70-J-T20 OPLC Installation Guide 12 Digital Inputs, include 1 HSC/Shaft-encoder Input, 2 Analog inputs (only when the digital inputs
More informationPanduit Basic Rack PDU
Panduit Basic Rack PDU User Manual Release 1.0 Issue 1.0 Copyright 2014 Panduit Corp. All rights reserved. No part of this book shall be reproduced, stored in a retrieval system, or transmitted by any
More informationwww.greenelectricalsupply.com Page 1 of 4 DESCRIPTION Replacement for Conventional T12HO and T8HO Fluorescent Lamps for Sign Applications APPLICATION Used for Outdoor Signage (Single or Double Sided) PRODUCT
More informationEcoFlex LED Neon Manual
Manual Part number: LN-ECO-XXXX-10m from Environmental Lights is one of the most flexible and cost-effective members of our line of LED Neon products. It allows you to achieve the creative potential of
More informationMFA-0801 & MFA-1201 D-M-E Smart Series Low Voltage Temperature Control System. User s Manual. D-M-E Company
MFA-0801 & MFA-1201 D-M-E Smart Series Low Voltage Temperature Control System User s Manual D-M-E Company D-M-E Company MFA-0801 & MFA-1201 Page 1 Copyright D-M-E Company 1995. All rights reserved. D-M-E
More informationSM Sygnus Hybrid Quick Installation Guide Version
SM Sygnus Hybrid Quick Installation Guide Version 1.0.4 2017 WARNINGS Do not work on the system or connect or disconnect cables during periods of lightning activity. This equipment must be grounded. Never
More informationG5 PDU Installation Guide
G5 PDU Installation Guide 1 Contents Before You Begin... 3 Overview... 3 Important Safety Information... 3 Required Tools... 5 Section 1 Introduction... 6 Classification Overview... 6 Features... 7 Form
More informationLightning Stitch Assembly
ABM International, Inc. 1 1.0: Parts List Lightning stitch motor and drive assembly (Qty. 1) Lightning stitch piggy backed controller board assembly (Qty. 1) Touchscreen (Qty. 1) 2 9-pin Serial cable (Qty.
More informationTRC-190 User s Manual
First Edition, November 2008 www.moxa.com/product 2008 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. The software described in this manual is furnished under a license agreement
More informationPit Transition with 24" Fan Installation and Operators Instruction Manual
Pit Transition with 4" Fan Installation and Operators Instruction Manual z Fan and Fan Framing Dimensions Shutter Fan " [8. cm] 6" [9.4 cm] 6-/4" [9. cm] Cone Fan " [5. cm] 4-/6" [88.4 cm] 75-/" [9.8 cm]
More informationILC LightLEEDer MicroLite 1000P Retrofit Installation
ILC LightLEEDer MicroLite 1000P Retrofit Installation Congratulations on the purchase of your new ILC LightLEEDer Retrofit System. The ILC LightLEEDer MicroLite Retrofit System is designed for the replacement
More informationPS/IO Circuit Board Retrofit
S&C 6800 Series Automatic Switch Controls PS/IO Circuit Board Retrofit Table of Contents Section Page Introduction Qualified Persons.... 2 Read this Instruction Sheet.... 2 Retain this Instruction Sheet....
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Vision OPLC V350-35-R34/V350-J-R34 Installation Guide The Unitronics V350-35-R34/V350-J-R34 offers the following onboard I/Os: 22 Digital Inputs, configurable via wiring to include 2 Analog and 3 HSC/Shaft-encoder
More informationPanduit Basic Rack PDU with Local Meter
Panduit Basic Rack PDU with Local Meter User Manual Release 1.0 Issue 1.0 Copyright 2014 Panduit Corp. All rights reserved. No part of this book shall be reproduced, stored in a retrieval system, or transmitted
More informationCarefully remove the translite from the backbox and then lower the speaker panel to the position shown in Fig. A to gain access to the backbox.
Installation Instructions for Data East (wooden speaker panel) Congratulations on the purchase of your new display. The will enhance your pinball machine by introducing color to the dot matrix display
More informationOperating instructions IO-Link master CabinetLine AL19xx
Operating instructions IO-Link master CabinetLine AL19xx 80273036/00 02/2018 1 Preliminary note Technical data, approvals, accessories and further information at www.ifm.com. 2 Safety instructions Read
More informationINSTALLATION DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER. Before installation:
DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER The DKM-409 is a precision instrument designed for displaying various AC parameters in 3-phase distribution panels. Thanks to its isolated
More informationPlasma Panel Replacement Guide DU-42PX12X
Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be
More informationABM International, Inc. Lightning Stitch Checklist 9/13/2013
ABM International, Inc. Lightning Stitch Checklist 9/13/2013 1) Piggy backed board assembly (1) Piggy back board assembly tested? Yes No 24v passed XB passed XA passed YB passed YA passed SAFE passed S/S
More informationThis 4200-RM Rack Mount Kit is for installation in 4200-CAB series cabinets only.
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 (440) 248-0400 Fax: (440) 248-6168 www.keithley.com Model 4200-RM Rack Mount Kit Packing List Introduction NOTE This 4200-RM Rack Mount
More informationPICO PROTECTOR PG-06 & PK-06 Series
PICO PROTECTOR PG-06 & PK-06 Series Installation Instructions LISTED 95P5 SIGNAL CIRCUIT PROTECTOR Introduction The Siemon Company s Pico Protector Kits protect voice and data equipment from sneak current
More informationInstalling and Configuring Rialto Analytic Appliances
Installing and Configuring Rialto Analytic Appliances Important Safety Information This manual provides installation and operation information and precautions for the use of this camera. Incorrect installation
More informationMounting on the Ceiling Using Flush Mount (Face Down)
Mounting on the Ceiling Using Flush Mount (Face Down) Installation Guide 2014/02/14 Table of Contents Safety Information... 3 Installation Procedures... 5 Step 1: Drill a Hole on the Ceiling... 5 Step
More informationTo connect the AC adapter:
Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator
More informationReplacing the Gateway M275 Keyboard
Replacing the Gateway M275 Keyboard This package includes a replacement keyboard for your Gateway M275 notebook and these printed instructions. Tools you need You need a small Phillips screwdriver and
More informationInstallation RA5112-C-16A-C20. Basic Rack Power Distribution Unit
Installation RA5112-C-16A-C20 Basic Rack Power Distribution Unit Contents Before You Begin........................1 Safety and grounding information..........1 How to Install the Rack PDU...............2
More informationBlackout Shutter Kits with Breathable Wall Light Traps
Blackout Shutter Kits with Breathable Wall Light Traps 2018 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. Revision date: 05.10.18 Maintain controlled airflow without
More informationJAN 16 Rev B
ANSI C136.41-2013 Rotatable Dimming Receptacles Application Specification 20 JAN 16 Rev B NOTE All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters
More informationBRB Systems USA Co. Instruction Manual. USA Trap Solo Voice Release System. 12V & 120V Versions.
BRB Systems USA Co. Instruction Manual. USA Trap Solo Voice Release System. 12V & 120V Versions. IMPORTANT: Read and understand this manual before assembling, installing or using this system. Improper
More information