Principal LED Street Stik Fluorescent Bulb Replacements

Size: px

Start display at page:

Download "Principal LED Street Stik Fluorescent Bulb Replacements"

Warren Knight
6 years ago
Views:

Principal LED Street Stik Fluorescent Bulb Replacements LED Retrofit Guide (PL-RT1-001) WARNING Installation must only be performed by a licensed electrician.

Save These Instructions Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

The grounding and bonding of the LED Driver shall be done in accordance with National Electric Code (NEC) Article 600. Follow all National Electric Codes (NEC) and local codes.

These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies.

1 Principal LED Street Stik Fluorescent Bulb Replacements LED Retrofit Guide (PL-RT1-001) WARNING Installation must only be performed by a licensed electrician. To prevent death, injury or damage to property this product must be installed in accordance with the National Electric Code in the USA or Canadian Electrical Code (CSA22.1) in Canada. Save These Instructions Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. Prepare Electrical Wiring Electrical Requirements Limited to use in dry and damp locations. The grounding and bonding of the LED Driver shall be done in accordance with National Electric Code (NEC) Article 600. Follow all National Electric Codes (NEC) and local codes. These products are only suitable for connection to a circuit from a Class 2 power source. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. *This Class [A] RFLD complies with the Canadian standard ICES-003. This product is intended solely for the use of non-residential signage lighting and is not intended for use in any other applications. Conforms to the following standards: Principal LED LLC Venture Drive San Angelo, TX info@p-led.com REV

2 Hardware Wire Wire Connectors Zip Ties Electrical Tape Wire Strippers Drill Screwdriver Drill bits Driver bits Tape Measure Multimeter Screws as required Components (PL-OP2-HW3-P/ST-SS-YY-ZZ, PL-OP2-HW3-P/ST-DS-YY-ZZ, PL-OP2-HW3-P/ST-SS-YY-ZZ (HD), PL- OP2-HW3-P/ST-DS-YY-ZZ (HD)* *YY: Length of Stik in inches; XX: Color Temperature (See Spec Sheets Attached), MW SS: Single-Sided, DS: Double-Sided, HD: High Density Class 2 Power Supply Specifications LED PS Model/ Cat Nos. Input Output per Circuit Max. Power Load PL-PS VAC - 240VAC / 1.2A 12VDC / 5A 60W PL U 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W PL MU 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W PL PCM-U 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W PL U 100VAC - 277VAC / 2.2A A 12VDC / 5A * 2 (Dual Output) 120W PL-QB1-MV60-S 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W PL-QB1-MV120-S 100VAC - 277VAC / 2.2A A 12VDC / 5A * 2 (Dual Output) 120W VLP U 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W VLP MU 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W VLP U 100VAC - 277VAC / 2.2A A 12VDC / 5A * 2 (Dual Output) 120W VLP PCM-U 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W

Fluorescent to LED Prior to installation, survey the site for information regarding power and accessibility inside and outside the building.

exceeding 20A, or that permitted by applicable local, state, or country electrical codes (whichever is less).

switch must be installed. If required, the disconnect switch shall be installed by qualified personnel, in accordance with applicable local, state, and country electrical codes.

Fill in all holes with the appropriate amount of rated sealant as needed (excluding weep holes). Lamp Ballast 1.

Inspect existing sockets and replace as needed. and ballast. 4. Install Principal LED Street Stiks into existing T12 sockets.

If installing multiple LED drivers, keep them at least 2 apart end to end and 4 apart along the sides. Mount power supplies with screws for to ensure it s secure.

3 Fluorescent to LED Prior to installation, survey the site for information regarding power and accessibility inside and outside the building. Ensure that the branch circuit supplying the existing transformer or ballast will be within the voltage ratings of the new LED power supply, and have a current rating not exceeding 20A, or that permitted by applicable local, state, or country electrical codes (whichever is less). If removal of the existing lighting equipment (see Step 2) eliminates the disconnect switch, as required by applicable local, state, or country electrical codes; a new disconnect switch must be installed. If required, the disconnect switch shall be installed by qualified personnel, in accordance with applicable local, state, and country electrical codes. Make sure the removal of lighting equipment does not compromise the integrity of the sign body. Fill in all holes with the appropriate amount of rated sealant as needed (excluding weep holes). Lamp Ballast 1. Ensure no power is going to the sign and disconnect the existing power ballast and gain access to lighting fixtures in sign. Remove existing T12 HO fluorescent bulbs Inspect existing sockets and replace as needed. and ballast. 4. Install Principal LED Street Stiks into existing T12 sockets. Position Stiks so that the LED s are facing the sign faces and continue replacing the T12 lamps. 5. If installing multiple LED drivers, keep them at least 2 apart end to end and 4 apart along the sides. Mount power supplies with screws for to ensure it s secure. Live Black to Black Neutral White to White Red (+) Red (+) Black (-) Black (-) to LEDs Primary AC wire to sign Green to Green Ground 6. Wire AC line to LED driver(s) in accordance with the applicable local, state, and country electrical codes. Connect black to black or brown, white to white or blue, and green to green. 7. On the secondary (12V) side of the power supply, connect the red wires (+) from the Street Stiks to the red wire (+) on the power supply using wire connectors and do the same for black wires (-). Do not place more Stiks on a power supply than is recommended by the Stik specifications.

4 Street Stik Single-Sided 18" 15.91" PL-OP2-HW3-P/ST-SS-18-XX 24" 21.91" PL-OP2-HW3-P/ST-SS-24-XX 30" 27.91" PL-OP2-HW3-P/ST-SS-30-XX 36" 33.91" PL-OP2-HW3-P/ST-SS-36-XX 42" 39.91" PL-OP2-HW3-P/ST-SS-42-XX 48" 45.91" PL-OP2-HW3-P/ST-SS-48-XX 60" 57.91" PL-OP2-HW3-P/ST-SS-60-XX 64" 61.91" PL-OP2-HW3-P/ST-SS-64-XX 72" 69.91" PL-OP2-HW3-P/ST-SS-72-XX 84" 81.91" PL-OP2-HW3-P/ST-SS-84-XX 96" 93.91" PL-OP2-HW3-P/ST-SS-96-XX 108" 105.9" PL-OP2-HW3-P/ST-SS-108-XX 117" " PL-OP2-HW3-P/ST-SS-117-XX 120" " PL-OP2-HW3-P/ST-SS-120-XX Street Stik Double-Sided 18" 15.91" PL-OP2-HW3-P/ST-DS-18-XX 24" 21.91" PL-OP2-HW3-P/ST-DS-24-XX 30" 27.91" PL-OP2-HW3-P/ST-DS-30-XX 36" 33.91" PL-OP2-HW3-P/ST-DS-36-XX 42" 39.91" PL-OP2-HW3-P/ST-DS-42-XX 48" 45.91" PL-OP2-HW3-P/ST-DS-48-XX 60" 57.91" PL-OP2-HW3-P/ST-DS-60-XX 64" 61.91" PL-OP2-HW3-P/ST-DS-64-XX 72" 69.91" PL-OP2-HW3-P/ST-DS-72-XX 84" 81.91" PL-OP2-HW3-P/ST-DS-84-XX 96" 93.91" PL-OP2-HW3-P/ST-DS-96-XX 108" 105.9" PL-OP2-HW3-P/ST-DS-108-XX 117" " PL-OP2-HW3-P/ST-DS-117-XX 120" " PL-OP2-HW3-P/ST-DS-120-XX Troubleshooting Tips Make sure output wiring is connected correctly. Turn off power and check wiring polarity. If so, reverse wires and illuminate. Make sure LED driver has the correct input voltage (VAC). Make sure there is no exposed wiring that could cause a short circuit. Make sure wire is in electrical contact at the UL listed connector. If the maximum number of Stiks has exceeded the sign or luminaire the Stiks may blink or not turn on. Count the Stiks and confirm the number of Stiks is within the maximum number listed in spec sheets attached.

5 Street Stik HD Single-Sided 18" 15.91" PL-OP2-HW3-P/ST-SS-18-XX (HD) 24" 21.91" PL-OP2-HW3-P/ST-SS-24-XX (HD) 30" 27.91" PL-OP2-HW3-P/ST-SS-30-XX (HD) 36" 33.91" PL-OP2-HW3-P/ST-SS-36-XX (HD) 42" 39.91" PL-OP2-HW3-P/ST-SS-42-XX (HD) 48" 45.91" PL-OP2-HW3-P/ST-SS-48-XX (HD) 60" 57.91" PL-OP2-HW3-P/ST-SS-60-XX (HD) 64" 61.91" PL-OP2-HW3-P/ST-SS-64-XX (HD) 72" 69.91" PL-OP2-HW3-P/ST-SS-72-XX (HD) 84" 81.91" PL-OP2-HW3-P/ST-SS-84-XX (HD) 96" 93.91" PL-OP2-HW3-P/ST-SS-96-XX (HD) 108" 105.9" PL-OP2-HW3-P/ST-SS-108-XX (HD) 117" " PL-OP2-HW3-P/ST-SS-117-XX (HD) 120" " PL-OP2-HW3-P/ST-SS-120-XX (HD) Street Stik HD Double-Sided T-12 Actual Length Lumens per Stik No. of Mods Watts Stiks per 60W PS Stiks per 120W PS Part Number* 18" 15.91" PL-OP2-HW3-P/ST-DS-18-XX (HD) 24" 21.91" PL-OP2-HW3-P/ST-DS-24-XX (HD) 30" 27.91" PL-OP2-HW3-P/ST-DS-30-XX (HD) 36" 33.91" PL-OP2-HW3-P/ST-DS-36-XX (HD) 42" 39.91" PL-OP2-HW3-P/ST-DS-42-XX (HD) 48" 45.91" PL-OP2-HW3-P/ST-DS-48-XX (HD) 60" 57.91" PL-OP2-HW3-P/ST-DS-60-XX (HD) 64" 61.91" PL-OP2-HW3-P/ST-DS-64-XX (HD) 72" 69.91" PL-OP2-HW3-P/ST-DS-72-XX (HD) 84" 81.91" PL-OP2-HW3-P/ST-DS-84-XX (HD) 96" 93.91" PL-OP2-HW3-P/ST-DS-96-XX (HD) 108" 105.9" PL-OP2-HW3-P/ST-DS-108-XX (HD) 117" " PL-OP2-HW3-P/ST-DS-117-XX (HD) 120" " PL-OP2-HW3-P/ST-DS-120-XX (HD) Troubleshooting Tips Make sure output wiring is connected correctly. Turn off power and check wiring polarity. If so, reverse wires and illuminate. Make sure LED driver has the correct input voltage (VAC). Make sure there is no exposed wiring that could cause a short circuit. Make sure wire is in electrical contact at the UL listed connector. If the maximum number of Stiks has exceeded the sign or luminaire the Stiks may blink or not turn on. Count the Stiks and confirm the number of Stiks is within the maximum number listed in spec sheets attached.

Principal LED Qwik Stik Fluorescent Bulb Replacements

Principal LED Qwik Stik Fluorescent Bulb Replacements LED Retrofit Guide (PL-RT1-001) WARNING Installation must only be performed by a licensed electrician. To prevent death, injury or damage to property