Hello and welcome to this Renesas Interactive module that provides an overview of the RX DMA Controller
|
|
- Kenneth Wilkerson
- 6 years ago
- Views:
Transcription
1 Hello and welcome to this Renesas Interactive module that provides an overview of the RX DMA Controller 1
2 The purpose of this Renesas Interactive module is to give you a basic understanding of the RX Direct Memory Access Controller or DMA. For a general overview of data movement peripherals like DMA s and DTC s, please see the Data Movement Peripherals overview module. This module provides: - An overview of the RX DMA controller - A brief discussion of the transfer modes the DMAC supports - An overview of the DMAC register set - and a short explanation of how the DMA controller works with the Interrupt Controller in the RX This module should take about 20 minutes to complete. Let s get started. 2
3 Here is a diagram of the RX Direct Memory Access Controller, or DMAC. The DMAC sits on Internal Main bus 2, and can act as a master on this bus, giving the DMAC access to on-chip RAM and flash as well as on-board peripherals. The DMAC is tightly coupled to the Interrupt Control Unit or ICU, allowing the ICU the trigger DMA transfers and the DMAC to generate interrupts to the CPU core. There are four independent channels in the RX DMAC, and each one has a dedicated set of control registers. 3
4 In normal mode, the DMAC transfers a single data item each time the DMAC is triggered. It can be triggered from a number of hardware sources or by a software request. During each transfer, a single 8-, 16-, or 32-bit data item is transferred from the source address to the destination address. Each time the DMAC is triggered, another data item is transferred from source to destination. The source & destination address registers keep track of where to move the data from and to. The DMAC can be configured to leave the source & destination addresses unchanged after a transfer, or to automatically increment or decrement one or both. Each address behavior can be configured independently allowing easy transfer to and from peripheral registers to memory buffers. Channel 0 has an additional mode that allows an offset to be added to an address rather than just a simple increment or decrement function. The transfer counter is decremented after each transfer, counting down to zero. It is 16-bits wide, allowing over 60,000 transfers to take place before the CPU has to intervene. Setting the transfer counter to zero puts the DMAC in free-run mode. Finally, the DMAC can generate an interrupt to the CPU at the end of each transfer. To restart the DMAC after the end of the transfer, you ll have to reset the source & destination addresses and the transfer counter. 4
5 The DMAC also supports Repeat Transfer Mode. As with normal mode, the DMAC transfers a single data item each time the DMAC is triggered. During each transfer, a single 8-, 16-, or 32-bit data item is transferred from the source address to the destination address. Each time the DMAC is triggered, a data item is transferred from source to destination. The source & destination address registers keep track of where to move the data from and to. As with normal mode, the DMAC can be configured to automatically increment or decrement one or both addresses. The source or the destination can be specified as the repeat area, and the size of the repeat area can be up to 1K. In this example, we ll use the source as the repeat area and a repeat area size of 4. At each trigger of the DMAC, a data item is transferred and the transfer count is decremented. A separate block count is decremented each time the end of the repeat area is reached. The block count can be a maximum of 1K. At this time, the address register for the repeat area is reset to its initial value. Since the source area is the repeat area in our example, the SAR register is reset to point to the start. The other address register continues to be updated, incrementing, decrementing, or remaining constant according to its configuration. Further triggers of the DMAC continue to transfer data, one item at a time. The repeat area is reset at the end of each scan, and the block counter is decremented. When the block counter reaches zero, the transfer ends and an interrupt can be generated to the CPU. An interrupt may also be generated at each repeat, although you ll need to be 5
6 aware that this suspends the DMA transfers for this channel and you ll need to re-arm it. 5
7 In Block Transfer Mode, the DMAC transfers an entire block of data from the source to the destination area. At each request, the DMAC transfers a block of data. The data within the block can be 8-, 16-, or 32-bit values. As with the other modes, the source & destination address registers keep track of where to move the data from and to. The updates to the source & destination addresses happen as each data item is moved during the block transfer, so if the source or destination address was set to increment, then at the end of the block transfer it will point to the first data item after the block. The source or the destination can be specified as the block area, and the size of the block area can be up to 1K. In this example, the destination is the block area and the block size is 3. A transfer counter is used internally by the DMAC as it transfers each block; initialize it to the block size. A separate block count is decremented each time the DMAC is triggered and a block is transferred. The address register of the block area resets to the start of the block area after each transfer. When the block counter reaches zero, the transfer ends and an interrupt can be generated to the CPU. An interrupt may also be generated at each block transfer. 6
8 Now let s look at the registers that control the function of the DMAC There are a core set of four registers that control the transfers. These are the source & destination address registers, and the transfer and block count registers. We ll see more about these in a bit. Mode & control registers setup the DMAC controllera nd interrupt & status registers allow you to monitor the completion of DMAC transfers Finally, it s important to note that you may need to set registers in the Interrupt Control Unit and any peripherals that you will use to trigger the DMAC. 7
9 Here s the DMAC register set. Each of the four DMAC channels has one set of these registers, with the exception of the two registers noted. The registers fall into a handful of functional groups. The source & destination address registers specify the source & destination for the data. The address mode register allows you to optionally update the address registers with each transfer. The source & destination addresses can each be fixed, incremented, or decremented. DMAC channel 0 also allows offset addition. In this mode, the value in the DMA offset register is added to source or destination address at each transfer. During transfers, the two count registers DMCRA and DMCRB keep track of the number of transfers and blocks or repeats. The DMA transfer mode register configures the DMAC for normal, repeat, or block mode, the size of data operands, and other options. Interrupts from the DMAC are controlled through the DMA interrupt setting register and the DMA activation source flag control register. The remaining control and status registers control starting & stopping of the DMAC 8
10 During DMA transfers, the DMAC moves data from the location pointed to by the Source Address Registers to the location pointed to by the Destination Address Register. Each register contains a 32-bit address. Valid addresses are anywhere in the upper or lower 256 megabytes of the RX 32-bit address space. This covers all on-chip memory and peripherals. To transfer data to and from memory and devices external to the chip, use the External DMA controller, or ExDMAC. Based on settings in the DMAC Address Mode Register, each of these registers can be incremented or decremented after each transfer. This allows for transfers from a fixed memory location like a register to a buffer, or vice versa, as well other operation. DMAC channel 0 also supports an offset addition mode, which allows an address register to be updated by a fixed offset after each transfer. 9
11 The DMA transfer count register is a single register that takes on two different configurations based on the DMA transfer mode. In normal mode, it is a 16-bit transfer counter that allows up to transfers. Write the desired number of transfers into the low word of the register. In repeat and block modes, the upper word contains the repeat size or block size, and the lower word contains the repeat or block count. During the transfers, the DMAC updates the count in the lower word as it performs the data movement, reloading it with the value from the upper word at each repeat or block transfer. Be sure to initialize both the upper and lower words to the same value since the value in the lower word controls the initial repeat cycle or block transfer. 10
12 The DMAC Block Transfer Counter Register is only used in Repeat & Block transfers. This register sets the number repeats or block transfers. Up to 1,024 repeats or blocks can be specified. 11
13 While the DMA Controller can be triggered by software requests, typically it is started by a signal from the Interrupt Control Unit generated by a peripheral. Configuring a hardware interrupt source to trigger the DMAC is very similar to configuring the interrupt for normal use. You ll need to set the local enables in the peripheral, plus the interrupt priority level and interrupt enable registers for the source. In addition, each DMA channel has a DMA Activation Source Select Register in the ICU. Each register contains the vector number of the interrupt source that is to trigger the corresponding DMA channel. Check the hardware manual for specifics of which peripheral interrupts are capable of being routed to DMA requests. The DMAC can also generate interrupts to the ICU to signal DMA events and exceptions to the CPU core. Interrupts can fire at each transfer, at the completion of each repeat or block, or at the end of the DMA transfer. Interrupts generated by the DMAC are enable by bits in the DMINT register. See the hardware manual for complete details. 12
14 This concludes this Renesas Interactive module. In this session you ve learned about - the RX DMA Controller, - the three transfer modes it supports, - the register set that controls the DMAC, - and how the Interrupt Control unit to provide triggers to the DMAC, as well as interrupts the DMAC can send to the ICU. Thanks for watching! 13
15 14
16 Thank You 15
Welcome to this presentation of the STM32 direct memory access controller (DMA). It covers the main features of this module, which is widely used to
Welcome to this presentation of the STM32 direct memory access controller (DMA). It covers the main features of this module, which is widely used to handle the STM32 peripheral data transfers. 1 The Direct
More informationINTERFACING INTERFACING. Richa Upadhyay Prabhu. February 29, 2016
INTERFACING Richa Upadhyay Prabhu NMIMS s MPSTME richa.upadhyay@nmims.edu February 29, 2016 DMA ; Direct Memory Access Controller (8257) Introduction Can I/O have direct access to memory? Introduction
More informationHT32 Series Microcontrollers PDMA Description
HT32 Series Microcontrollers PDMA Description D/N: AN0310E Introduction PDMA Some of the HT32 series microcontrollers such as the HT32F1755/1765/2755, contain an integrated 8~12 channel PDMA, which supports
More informationHello and welcome to this Renesas Interactive module that covers the Independent watchdog timer found on RX MCUs.
Hello and welcome to this Renesas Interactive module that covers the Independent watchdog timer found on RX MCUs. 1 This course covers specific features of the independent watchdog timer on RX MCUs. If
More informationUnderstand the design, features, operation, and application of the Data Transfer Controller (DTC) and DMA Controller (DMAC).
Module Introduction Purpose This training module provides an overview of the peripherals in H8S series microcontrollers that you can use to transfer data without interrupting the CPU. Objective Understand
More information3. Controtlto specify the mode of transfer such as read or write 4. A control to start the DMA transfer
DMA Controller The DMA controller needs the usual circuits of an interface to communicate the CPU and 10 device. In addition, it needs an address register, a word count register, and a set of address lines.
More informationHello and welcome to this Renesas Interactive module that provides an architectural overview of the RX Core.
Hello and welcome to this Renesas Interactive module that provides an architectural overview of the RX Core. 1 The purpose of this Renesas Interactive module is to introduce the RX architecture and key
More informationQuestion Bank Microprocessor and Microcontroller
QUESTION BANK - 2 PART A 1. What is cycle stealing? (K1-CO3) During any given bus cycle, one of the system components connected to the system bus is given control of the bus. This component is said to
More information6 Direct Memory Access (DMA)
1 License: http://creativecommons.org/licenses/by-nc-nd/3.0/ 6 Direct Access (DMA) DMA technique is used to transfer large volumes of data between I/O interfaces and the memory. Example: Disk drive controllers,
More informationM16C/62 APPLICATION NOTE. Using the M16C/62 DMAC in Forward Source Mode. 1.0 Abstract. 2.0 Introduction
APPLICATION NOTE M16C/62 1.0 Abstract The following article introduces and shows an example of how to use the DMAC function of the M16C/62 with a forward counting source address and fixed destination address.
More information_ V Renesas R8C In-Circuit Emulation. Contents. Technical Notes
_ V9.12. 225 Technical Notes Renesas R8C In-Circuit Emulation This document is intended to be used together with the CPU reference manual provided by the silicon vendor. This document assumes knowledge
More informationComputer Organization ECE514. Chapter 5 Input/Output (9hrs)
Computer Organization ECE514 Chapter 5 Input/Output (9hrs) Learning Outcomes Course Outcome (CO) - CO2 Describe the architecture and organization of computer systems Program Outcome (PO) PO1 Apply knowledge
More informationLecture1: introduction. Outline: History overview Central processing unite Register set Special purpose address registers Datapath Control unit
Lecture1: introduction Outline: History overview Central processing unite Register set Special purpose address registers Datapath Control unit 1 1. History overview Computer systems have conventionally
More informationUNIT II SYSTEM BUS STRUCTURE 1. Differentiate between minimum and maximum mode 2. Give any four pin definitions for the minimum mode. 3. What are the pins that are used to indicate the type of transfer
More informationCS370 Operating Systems
CS370 Operating Systems Colorado State University Yashwant K Malaiya Fall 2016 Lecture 2 Slides based on Text by Silberschatz, Galvin, Gagne Various sources 1 1 2 System I/O System I/O (Chap 13) Central
More informationBasics of Microprocessor
Unit 1 Basics of Microprocessor 1. Microprocessor Microprocessor is a multipurpose programmable integrated device that has computing and decision making capability. This semiconductor IC is manufactured
More informationM16C/26 APPLICATION NOTE. Using the DMAC with a Forward Source. 1.0 Abstract. 2.0 Introduction
APPLICATION NOTE 1.0 Abstract The following article introduces and shows an example of how to use the DMAC function of the with a forward counting source address and fixed destination address. 2.0 Introduction
More information-Device. -Physical or virtual thing that does something -Software + hardware to operate a device (Controller runs port, Bus, device)
Devices -Host -CPU -Device -Controller device) +memory +OS -Physical or virtual thing that does something -Software + hardware to operate a device (Controller runs port, Bus, Communication -Registers -Control
More informationHello and welcome to this Renesas Interactive course that covers the Watchdog timer found on RX MCUs.
Hello and welcome to this Renesas Interactive course that covers the Watchdog timer found on RX MCUs. 1 This course covers specific features of the watchdog timer on RX MCUs. If you need basic information
More informationFR Series MCUs with on-chip DMAC
FR Series MCUs with on-chip DMAC Introduction... 1 Overview... 1 I/O Transfer Methods... 1 Why DMA?... 1 DMA Transfer Types... 1 Synchronous DMA... 1 Single/Block Transfer... 2 Demand Transfer... 2 Burst
More informationMICROPROCESSOR TECHNOLOGY
MICROPROCESSOR TECHNOLOGY Assis. Prof. Hossam El-Din Moustafa Lecture 14 Ch.6 The 80186, 80188, and 80286 Microprocessors 21-Apr-15 1 Timers The 80186/80188 contain three fully programmable 16-bit timers
More informationCourse Introduction. Purpose: Objectives: Content: 27 pages 4 questions. Learning Time: 20 minutes
Course Introduction Purpose: This course provides an overview of the Direct Memory Access Controller and the Interrupt Controller on the SH-2 and SH-2A families of 32-bit RISC microcontrollers, which are
More informationRL78 Serial interfaces
RL78 Serial interfaces Renesas Electronics 00000-A Introduction Purpose This course provides an introduction to the RL78 serial interface architecture. In detail the different serial interfaces and their
More informationInfineon C167CR microcontroller, 256 kb external. RAM and 256 kb external (Flash) EEPROM. - Small single-board computer (SBC) with an
Microcontroller Basics MP2-1 week lecture topics 2 Microcontroller basics - Clock generation, PLL - Address space, addressing modes - Central Processing Unit (CPU) - General Purpose Input/Output (GPIO)
More informationInput/Output Systems
Input/Output Systems CSCI 315 Operating Systems Design Department of Computer Science Notice: The slides for this lecture have been largely based on those from an earlier edition of the course text Operating
More informationComputer System Architecture
CSC 203 1.5 Computer System Architecture Department of Statistics and Computer Science University of Sri Jayewardenepura Addressing 2 Addressing Subject of specifying where the operands (addresses) are
More informationThe Instruction Set. Chapter 5
The Instruction Set Architecture Level(ISA) Chapter 5 1 ISA Level The ISA level l is the interface between the compilers and the hardware. (ISA level code is what a compiler outputs) 2 Memory Models An
More informationChapter 7 Central Processor Unit (S08CPUV2)
Chapter 7 Central Processor Unit (S08CPUV2) 7.1 Introduction This section provides summary information about the registers, addressing modes, and instruction set of the CPU of the HCS08 Family. For a more
More informationComputer Systems Overview
Computer Systems Overview Maurizio Pizzonia slides adattate da W. Stalling Operating Systems: Internals and Design Principles http://williamstallings.com/os/os5e.html 1 Basic Elements Processor Main Memory
More informationComputer-System Organization (cont.)
Computer-System Organization (cont.) Interrupt time line for a single process doing output. Interrupts are an important part of a computer architecture. Each computer design has its own interrupt mechanism,
More informationHello, and welcome to this presentation of the STM32 I²C interface. It covers the main features of this communication interface, which is widely used
Hello, and welcome to this presentation of the STM32 I²C interface. It covers the main features of this communication interface, which is widely used to connect devices such as microcontrollers, sensors,
More informationTop-Level View of Computer Organization
Top-Level View of Computer Organization Bởi: Hoang Lan Nguyen Computer Component Contemporary computer designs are based on concepts developed by John von Neumann at the Institute for Advanced Studies
More informationicroprocessor istory of Microprocessor ntel 8086:
Microprocessor A microprocessor is an electronic device which computes on the given input similar to CPU of a computer. It is made by fabricating millions (or billions) of transistors on a single chip.
More informationI/O Management and Disk Scheduling. Chapter 11
I/O Management and Disk Scheduling Chapter 11 Categories of I/O Devices Human readable used to communicate with the user video display terminals keyboard mouse printer Categories of I/O Devices Machine
More informationChapter 3. Top Level View of Computer Function and Interconnection. Yonsei University
Chapter 3 Top Level View of Computer Function and Interconnection Contents Computer Components Computer Function Interconnection Structures Bus Interconnection PCI 3-2 Program Concept Computer components
More informationTutorial Introduction
Tutorial Introduction PURPOSE: This tutorial describes the key features of the DSP56300 family of processors. OBJECTIVES: Describe the main features of the DSP 24-bit core. Identify the features and functions
More informationWelcome to this Renesas Interactive course which covers migration from the the V850 Jx3 series of 32bit MCUs to the Jx4 Series.
Welcome to this Renesas Interactive course which covers migration from the the V850 Jx3 series of 32bit MCUs to the Jx4 Series. The J Series provides a combination of high-performance processing power
More informationGeneric Model of I/O Module Interface to CPU and Memory Interface to one or more peripherals
William Stallings Computer Organization and Architecture 7 th Edition Chapter 7 Input/Output Input/Output Problems Wide variety of peripherals Delivering different amounts of data At different speeds In
More informationembos Real-Time Operating System embos plug-in for IAR C-Spy Debugger Document: UM01025 Software Version: 3.0 Revision: 0 Date: September 18, 2017
embos Real-Time Operating System embos plug-in for IAR C-Spy Debugger Document: UM01025 Software Version: 3.0 Revision: 0 Date: September 18, 2017 A product of SEGGER Microcontroller GmbH & Co. KG www.segger.com
More informationDepartment of Computer Science, Institute for System Architecture, Operating Systems Group. Real-Time Systems '08 / '09. Hardware.
Department of Computer Science, Institute for System Architecture, Operating Systems Group Real-Time Systems '08 / '09 Hardware Marcus Völp Outlook Hardware is Source of Unpredictability Caches Pipeline
More informationQUESTION BANK CS2252 MICROPROCESSOR AND MICROCONTROLLERS
FATIMA MICHAEL COLLEGE OF ENGINEERING & TECHNOLOGY Senkottai Village, Madurai Sivagangai Main Road, Madurai -625 020 QUESTION BANK CS2252 MICROPROCESSOR AND MICROCONTROLLERS UNIT 1 - THE 8085 AND 8086
More informationDesigning with ALTERA SoC Hardware
Designing with ALTERA SoC Hardware Course Description This course provides all theoretical and practical know-how to design ALTERA SoC devices under Quartus II software. The course combines 60% theory
More informationRX Family APPLICATION NOTE. I 2 C Bus Interface (RIIC) Module Using Firmware Integration Technology. Introduction. Target Device.
I 2 C Bus Interface (RIIC) Module Using Firmware Integration Technology Introduction APPLICATION NOTE R01AN1692EJ0231 Rev. 2.31 This application note describes the I 2 C bus interface (RIIC) module using
More informationRX Family APPLICATION NOTE. Simple I 2 C Module Using Firmware Integration Technology. Introduction. Target Device.
APPLICATION NOTE RX Family R01AN1691EJ0220 Rev. 2.20 Introduction This application note describes the simple I 2 C module using firmware integration technology (FIT) for communications between devices
More informationIntroduction to Operating Systems Prof. Chester Rebeiro Department of Computer Science and Engineering Indian Institute of Technology, Madras
Introduction to Operating Systems Prof. Chester Rebeiro Department of Computer Science and Engineering Indian Institute of Technology, Madras Week - 04 Lecture 17 CPU Context Switching Hello. In this video
More informationDigital System Design Using Verilog. - Processing Unit Design
Digital System Design Using Verilog - Processing Unit Design 1.1 CPU BASICS A typical CPU has three major components: (1) Register set, (2) Arithmetic logic unit (ALU), and (3) Control unit (CU) The register
More informationAdvanced Parallel Architecture Lesson 3. Annalisa Massini /2015
Advanced Parallel Architecture Lesson 3 Annalisa Massini - 2014/2015 Von Neumann Architecture 2 Summary of the traditional computer architecture: Von Neumann architecture http://williamstallings.com/coa/coa7e.html
More informationInput/Output Problems. External Devices. Input/Output Module. I/O Steps. I/O Module Function Computer Architecture
168 420 Computer Architecture Chapter 6 Input/Output Input/Output Problems Wide variety of peripherals Delivering different amounts of data At different speeds In different formats All slower than CPU
More informationUnit 3 and Unit 4: Chapter 4 INPUT/OUTPUT ORGANIZATION
Unit 3 and Unit 4: Chapter 4 INPUT/OUTPUT ORGANIZATION Introduction A general purpose computer should have the ability to exchange information with a wide range of devices in varying environments. Computers
More informationComputer System Overview. Chapter 1
Computer System Overview Chapter 1 Operating System Exploits the hardware resources of one or more processors Provides a set of services to system users Manages secondary memory and I/O devices Basic Elements
More informationArchitecture of 8085 microprocessor
Architecture of 8085 microprocessor 8085 consists of various units and each unit performs its own functions. The various units of a microprocessor are listed below Accumulator Arithmetic and logic Unit
More informationRenesas 78K/78K0R/RL78 Family In-Circuit Emulation
_ Technical Notes V9.12.225 Renesas 78K/78K0R/RL78 Family In-Circuit Emulation This document is intended to be used together with the CPU reference manual provided by the silicon vendor. This document
More informationELC4438: Embedded System Design ARM Cortex-M Architecture II
ELC4438: Embedded System Design ARM Cortex-M Architecture II Liang Dong Electrical and Computer Engineering Baylor University Memory system The memory systems in microcontrollers often contain two or more
More informationThis application note demonstrates how to use the Direct Memory Access (DMA) module of the EFM32.
Direct Memory Access AN0013 - Application Note Introduction This application note demonstrates how to use the Direct Memory Access (DMA) module of the EFM32. Memory to memory, peripheral to memory, ping-pong
More informationData Transfer between On-chip RAM Areas with DMAC (Burst Mode) 1. Introduction Description of Sample Application... 3
Introduction APPLICATION NOTE This application note describes the operation of the DMAC, and is intended for reference to help in the design of user software. Target Device SH7211 Contents 1. Introduction...
More informationArm Assembly Language programming. 2. Inside the ARM
2. Inside the ARM In the previous chapter, we started by considering instructions executed by a mythical processor with mnemonics like ON and OFF. Then we went on to describe some of the features of an
More information1. Define Peripherals. Explain I/O Bus and Interface Modules. Peripherals: Input-output device attached to the computer are also called peripherals.
1. Define Peripherals. Explain I/O Bus and Interface Modules. Peripherals: Input-output device attached to the computer are also called peripherals. A typical communication link between the processor and
More information6 THE ETRAX Introduction. Special registers. 6 The ETRAX 4
6 THE ETRAX 4 6.1 Introduction The ETRAX 4 is the processor prior to the ETRAX 1 in the ETRAX family. The differences between the CRIS implementation in the ETRAX 1 and the ETRAX 4 are presented in this
More informationSYLLABUS UNIT - I 8086/8088 ARCHITECTURE AND INSTRUCTION SET
1 SYLLABUS UNIT - I 8086/8088 ARCHITECTURE AND INSTRUCTION SET Intel 8086/8088 Architecture Segmented Memory, Minimum and Maximum Modes of Operation, Timing Diagram, Addressing Modes, Instruction Set,
More informationEFM32 Series 0: DMA (ARM PrimeCell µdma PL230)
EFM32 Series 0: DMA (ARM PrimeCell µdma PL230) EFM32 - DMA DMA has read/write access to most of the EFM32 memory map Flash writes can not be done in memory map, but through sequenced writes to peripheral
More informationUnit DMA CONTROLLER 8257
DMA CONTROLLER 8257 In microprocessor based system, data transfer can be controlled by either software or hardware. To transfer data microprocessor has to do the following tasks: Fetch the instruction
More information1 MALP ( ) Unit-1. (1) Draw and explain the internal architecture of 8085.
(1) Draw and explain the internal architecture of 8085. The architecture of 8085 Microprocessor is shown in figure given below. The internal architecture of 8085 includes following section ALU-Arithmetic
More informationNios DMA. General Description. Functional Description
Nios DMA January 2003, Version 1.1 Data Sheet General Functional The Nios DMA module is an Altera SOPC Builder library component included in the Nios development kit. The DMA module allows for efficient
More informationIntroduction to ARM LPC2148 Microcontroller
Introduction to ARM LPC2148 Microcontroller Dr.R.Sundaramurthy Department of EIE Pondicherry Engineering College Features of LPC2148 in a Nut Shell CPU = ARM 7 Core Word Length = 32 Bit ROM = 512 KB RAM
More informationembos Real-Time Operating System embos plug-in for IAR C-Spy Debugger Document: UM01025 Software Version: 3.1 Revision: 0 Date: May 3, 2018
embos Real-Time Operating System Document: UM01025 Software Version: 3.1 Revision: 0 Date: May 3, 2018 A product of SEGGER Microcontroller GmbH www.segger.com 2 Disclaimer Specifications written in this
More informationUNIT V MICRO CONTROLLER PROGRAMMING & APPLICATIONS TWO MARKS. 3.Give any two differences between microprocessor and micro controller.
UNIT V -8051 MICRO CONTROLLER PROGRAMMING & APPLICATIONS TWO MARKS 1. What is micro controller? Micro controller is a microprocessor with limited number of RAM, ROM, I/O ports and timer on a single chip
More informationHistory and Basic Processor Architecture
History and Basic Processor Architecture History of Computers Module 1 Section 1 What Is a Computer? An electronic machine, operating under the control of instructions stored in its own memory, that can
More informationComputer System Overview
Computer System Overview Chapter 1 Muhammad Adri, MT 1 Operating System Exploits the hardware resources of one or more processors Provides a set of services to system users Manages secondary memory and
More informationOrganisasi Sistem Komputer
LOGO Organisasi Sistem Komputer OSK 5 Input Output 1 1 PT. Elektronika FT UNY Input/Output Problems Wide variety of peripherals Delivering different amounts of data At different speeds In different formats
More informationThe functional block diagram of 8085A is shown in fig.4.1.
Lecture-13 Internal Architecture of Intel 05A The functional block diagram of 05A is shown in fig.4.1. INTA INTR RST7.5 RST5.5 RST6.5 TRAP SOD SID INTERRUPT SERIAL I/O (Internal Bus) FR(S) IR() B() C()
More informationINTRODUCTION TO FLEXIO
INTRODUCTION TO FLEXIO Osvaldo Romero Applications Engineer EXTERNAL USE Agenda Introduction to FlexIO FlexIO Main Features FlexIO Applications Freescale Products with FlexIO Collaterals\Tools for FlexIO
More informationChapter 3 - Top Level View of Computer Function
Chapter 3 - Top Level View of Computer Function Luis Tarrataca luis.tarrataca@gmail.com CEFET-RJ L. Tarrataca Chapter 3 - Top Level View 1 / 127 Table of Contents I 1 Introduction 2 Computer Components
More informationInterrupt/Timer/DMA 1
Interrupt/Timer/DMA 1 Exception An exception is any condition that needs to halt normal execution of the instructions Examples - Reset - HWI - SWI 2 Interrupt Hardware interrupt Software interrupt Trap
More informationKeyStone Training. Multicore Navigator Overview
KeyStone Training Multicore Navigator Overview What is Navigator? Overview Agenda Definition Architecture Queue Manager Sub-System (QMSS) Packet DMA () Descriptors and Queuing What can Navigator do? Data
More informationRegister Are Two Names For The Same Place
The Program Counter And The Instruction Register Are Two Names For The Same Place Hi I am wondering where the program counter goes when the program The interrupt will take place after the current iteration
More informationInternal architecture of 8086
Case Study: Intel Processors Internal architecture of 8086 Slide 1 Case Study: Intel Processors FEATURES OF 8086 It is a 16-bit μp. 8086 has a 20 bit address bus can access up to 220 memory locations (1
More informationIntegrated Device Technology, Inc Stender Way, Santa Clara, CA Phone #: (408) Fax #: (408) Errata Notification
Integrated Device Technology, Inc. 2975 Stender Way, Santa Clara, CA - 95054 Phone #: (408) 727-6116 Fax #: (408) 727-2328 Errata Notification EN #: IEN01-02 Errata Revision #: 11/5/01 Issue Date: December
More informationIntroduction to Embedded Systems
Stefan Kowalewski, 4. November 25 Introduction to Embedded Systems Part 2: Microcontrollers. Basics 2. Structure/elements 3. Digital I/O 4. Interrupts 5. Timers/Counters Introduction to Embedded Systems
More information* USB Full-Speed Hub Controller
* Full-Speed Hub Controller RENESAS 8Bit Single-chip Microcomputer 740 Family / 38000 Series Code:U_38K2 Date:Oct.10 06 Page: 1 of 13 Advantage of 38K2 group (#1) function #1 Point 1 Easy setting! Can
More informationAutomating with STEP 7 in STL
Automating with STEP 7 in STL SIMATICS 7-300/400 Programmable Controllers by Hans Berger Publicis MCD Verlag Contents Introduction 16 1 SIMATIC S 7-300/400 Programmable Controller 17 1.1 Structure of the
More informationThe Nios II Family of Configurable Soft-core Processors
The Nios II Family of Configurable Soft-core Processors James Ball August 16, 2005 2005 Altera Corporation Agenda Nios II Introduction Configuring your CPU FPGA vs. ASIC CPU Design Instruction Set Architecture
More informationProduct Technical Brief S3C2413 Rev 2.2, Apr. 2006
Product Technical Brief Rev 2.2, Apr. 2006 Overview SAMSUNG's is a Derivative product of S3C2410A. is designed to provide hand-held devices and general applications with cost-effective, low-power, and
More informationChapter 1: Basics of Microprocessor [08 M]
Microprocessor: Chapter 1: Basics of Microprocessor [08 M] It is a semiconductor device consisting of electronic logic circuits manufactured by using either a Large scale (LSI) or Very Large Scale (VLSI)
More informationIntroduction to Microprocessor
Introduction to Microprocessor The microprocessor is a general purpose programmable logic device. It is the brain of the computer and it performs all the computational tasks, calculations data processing
More informationDevice-Functionality Progression
Chapter 12: I/O Systems I/O Hardware I/O Hardware Application I/O Interface Kernel I/O Subsystem Transforming I/O Requests to Hardware Operations Incredible variety of I/O devices Common concepts Port
More informationChapter 12: I/O Systems. I/O Hardware
Chapter 12: I/O Systems I/O Hardware Application I/O Interface Kernel I/O Subsystem Transforming I/O Requests to Hardware Operations I/O Hardware Incredible variety of I/O devices Common concepts Port
More informationOperating System: an Overview. Lucia Dwi Krisnawati, MA
Operating System: an Overview Lucia Dwi Krisnawati, MA What is an Operating System? A program that acts as an intermediary between a user of a computer and the computer hardware. Operating system goals:
More informationMicroprocessor & Interfacing Lecture DMA Controller--1
Microprocessor & Interfacing Lecture 26 8237 DMA Controller--1 E C S D E P A R T M E N T D R O N A C H A R Y A C O L L E G E O F E N G I N E E R I N G Contents Introduction Features Basic Process of DMA
More informationThis set of Microprocessor Multiple Choice Questions & Answers (MCQs) focuses on PIO 8255 (Programmable Input Output Port).
This set of Microprocessor Multiple Choice Questions & Answers (MCQs) focuses on PIO 8255 (Programmable Input Output Port). 1. Programmable peripheral input-output port is other name for a) serial input-output
More informationDesign and development of embedded systems for the Internet of Things (IoT) Fabio Angeletti Fabrizio Gattuso
Design and development of embedded systems for the Internet of Things (IoT) Fabio Angeletti Fabrizio Gattuso Microcontroller It is essentially a small computer on a chip Like any computer, it has memory,
More informationMOXSYN. General Description. Features. Symbol
MOXSYN C68MX11 CPU General Description The C68MX11 CPU core is based on the Motorola M68HC11 microcontroller controller, but has an enhanced full 16 bit architecture, thus requiring less clock cycles for
More informationProduct Technical Brief S3C2412 Rev 2.2, Apr. 2006
Product Technical Brief S3C2412 Rev 2.2, Apr. 2006 Overview SAMSUNG's S3C2412 is a Derivative product of S3C2410A. S3C2412 is designed to provide hand-held devices and general applications with cost-effective,
More informationChapter 8. Input Output Organization
Chapter 8 Input Output Organization 8.1 Introduction: In the design of a simple computer, we assumed one input device and one output device transferring data in and out of the accumulator using a programmed
More information1. Specifications Conditions for Application Description of Modules Used Description of Operation... 7
APPLICATION NOTE H8SX Family Introduction Relative phases of the two-phase pulse signal input from the two external clock pins are detected by the 6-bit timer pulse unit (TPU). Whether the timer counter
More information8/26/2010. Introduction to 8085 BLOCK DIAGRAM OF INTEL Introduction to Introduction to Three Units of 8085
BLOCK DIAGRAM OF INTEL 8085 GURSHARAN SINGH TATLA Introduction to 8085 It was introduced in 1977. It is 8-bit microprocessor. Its actual name is 8085 A. It is single NMOS device. It contains 6200 transistors
More informationInterrupts, timers and counters
Interrupts, timers and counters Posted on May 10, 2008, by Ibrahim KAMAL, in Micro-controllers, tagged Most microcontrollers come with a set of ADD-ONs called peripherals, to enhance the functioning of
More informationProduct Technical Brief S3C2440X Series Rev 2.0, Oct. 2003
Product Technical Brief S3C2440X Series Rev 2.0, Oct. 2003 S3C2440X is a derivative product of Samsung s S3C24XXX family of microprocessors for mobile communication market. The S3C2440X s main enhancement
More informationMicrocontroller & Interfacing
Course Title Course Code Microcontroller & Interfacing EC406 Lecture : 3 Course Credit Practical : 1 Tutorial : 0 Total : 4 Course Objective At the end of the course the students will be able to Understand
More informationCPU ARCHITECTURE. QUESTION 1 Explain how the width of the data bus and system clock speed affect the performance of a computer system.
CPU ARCHITECTURE QUESTION 1 Explain how the width of the data bus and system clock speed affect the performance of a computer system. ANSWER 1 Data Bus Width the width of the data bus determines the number
More informationInterrupts Peter Rounce - room 6.18
Interrupts Peter Rounce - room 6.18 P.Rounce@cs.ucl.ac.uk 20/11/2006 1001 Interrupts 1 INTERRUPTS An interrupt is a signal to the CPU from hardware external to the CPU that indicates than some event has
More information