EtherNet/IP to Allen-Bradley DH+ or Remote I/O Gateway AN-X-AB-DHRIO

Transcription

1 EtherNet/IP to Allen-Bradley DH+ or Remote I/O Gateway AN-X-AB-DHRIO The EtherNet/IP to Allen-Bradley Data Highway Plus or Remote I/O Gateway provides solutions for some commonly encountered issues where Allen-Bradley PLC5 and SLC processors are connected to a Data Highway Plus or Remote I/O network. When used as a Data Highway Plus bridge this gateway enables HMIs, RSLogix 5, and RSLogix 500 software to connect and communicate to the processors. In addition to enabling remote programming or monitoring of these PLCs or SLCs this bridge can enable an Allen-Bradley CompactLogix controller to communicate to the PLC5s and SLCs on the Data Highway Plus network. When this gateway is configured as a Remote I/O scanner it enables a Programmable Automation Controller (PAC) to control a legacy Remote I/O system facilitating processor upgrades. This gateway allows a phased approach to be used when upgrading or replacing legacy PLC5 or SLC controllers. The gateway provides automatic detection of the Remote I/O baud rate and creation of the Remote I/O racks. Once Block Transfers are configured the Auto-Configuration feature creates RSLogix 5000 tags reducing engineering effort. Once the new PAC is commissioned the legacy I/O can be upgraded one module or one rack at a time as scheduled downtime is available. This gateway minimizes the risk of excessive downtime when upgrading legacy Remote I/O systems. Data Highway Plus Features: Enables combinations of HMIs, programming terminals, and/or processors on an EtherNet/IP network access to the legacy processors on a DH+ network This gateway configures through a web browser (No special configuration software required) DH+ Station address is configurable from 0-77 (octal) Supports all DH+ baud rates (57.6, and Kbaud) DH+ network diagnostics, including a station listing all of all active nodes, are available through the web browser Multi-colored LED indicates the status of the DH+ network

2 Remote I/O Scanner Features: Auto-Configuration utility discovers baud rate and maps racks reducing configuration errors Partial Rack support All Remote I/O baud rates are supported (57.6, 115.2, and Kbaud) Auto-Configuration files are editable or customizable after their initial creation providing customization / flexibility Supports offline configuration through a CSV file Monitoring tools are provided via the web interface to monitor input and output values Web pages include Remote I/O diagnostics for Block Transfers, any configured racks, and the Remote I/O network Supports up to 32 Remote I/O adapters, and rack numbers 0 76 (Octal) Supports up to 15 I/O connections to a ControlLogix processor for I/O Each connection can have a unique RPI from msec Auto-Configuration feature maps the discovered Remote I/O points into ControlLogix I/O connections User can specify an Alias Base tag to be used in mapping the pre-defined I/O Multi-colored LED indicates the status of the Remote I/O network connection Remote I/O Rack and Network diagnostics can be mapped into the ControlLogix Processor using an additional connection Hardware Specifications Specification Ports Typical Power Consumption Maximum Power Dissapation Operating Temp Storage Temperature Dimensions Humidity Description 1 RJ45 10/100 Mbps Ethernet port 1 Phoenix 3-pin power connector 1 Phoenix 3-pin DH+ or Remote I/O connector Vdc or Vdc 3.6W 32 F to 122 F (0 ºC to 50 ºC) -40 F to 185 F (-40 ºC to 85 ºC) 107 mm x 126 mm x 34 mm (4.18 in x 4.97 in x 1.33 in) not including connectors 5% to 95% RH, with no condensation Desktop use or DIN Rail Mountable Ordering Information EtherNet/IP to Allen-Bradley DH+ or Remote I/O Gateway AN-X-AB-DHRIO How to Contact Us: Sales and Support Sales and Technical Support for this product are provided by ProSoft Technology. Contact our worldwide Sales or Technical Support teams directly by phone or Asia Pacific , asiapc@prosoft-technology.com Europe Middle East Africa +33 (0) , Europe@prosoft-technology.com North America , support@prosoft-technology.com Latin America (Sales only) , latinam@prosoft-technology.com

3 EtherNet/IP to GE Genius Gateway AN-X-GENI The EtherNet/IP to GE Genius gateway allows an Allen-Bradley Programmable Automation Controller (PAC) to control GE Genius I/O devices. This gateway allows a phased migration approach to be used when upgrading or replacing GE Genius based 90-30s and 90-70s controllers. The gateway provides automatic creation of the Genius scan-list and generates the associated RSLogix 5000 tags reducing engineering effort. Monitor mode allows verification of your conversion logic using live I/O data without impacting the running legacy system. Once the new PAC is commissioned the legacy I/O can be upgraded one module or one rack at a time as scheduled downtime is available. This gateway minimizes the risk of excessive downtime when upgrading legacy control systems. General Features: Configures through a web browser (No special configuration software required) Customizable configuration files provide additional flexibility Supports offline configuration through a.csv file Monitor mode enables testing and verification of PAC logic before controlling physical I/O, reducing the risk of production loss due to programming errors View diagnostics with a web browser enabling remote monitoring and troubleshooting GE Genius Bus Features: Supports sending and receiving Global Data on the Genius Network Supports standard and extended baud rates: 38, 76.8, 153.6, and Kbps Configurable Bus Address Auto-Configuration feature discovers and maps up to 31 Genius Blocks of I/O [Online] Multi-colored LED that indicates the status of the Genius Bus network connection

4 EtherNet/IP Features: Supports up to 16 I/O connections for real time control Each connection can have a unique RPI from msec allowing the prioritization of I/O data Auto-Configuration feature maps the discovered GE I/O points into tags in the PAC controller Diagnostic data can be mapped into PAC memory making this data available to HMIs Hardware Specifications Specification Ports Typical Power Consumption Maximum Power Dissapation Operating Temp Storage Temperature Dimensions Humidity Description 1 RJ45 10/100 Mbps Ethernet port 1 Phoenix 5-pin GE Genius Bus connector 1 Phoenix 3-pin power connector Vdc or Vdc 3W 32 F to 122 F (0 ºC to 50 ºC) -40 F to 185 F (-40 ºC to 85 ºC) 107 mm X 126 mm x 34 mm (4.18 in x 4.97 in x 1.33 in) not including connectors 5% to 95% RH, with no condensation Desktop use or DIN Rail Mountable Ordering Information EtherNet/IP to GE Genius Gateway AN-X-GENI How to Contact Us: Sales and Support Sales and Technical Support for this product are provided by ProSoft Technology. Contact our worldwide Sales or Technical Support teams directly by phone or Asia Pacific , asiapc@prosoft-technology.com Europe Middle East Africa +33 (0) , Europe@prosoft-technology.com North America , support@prosoft-technology.com Latin America (Sales only) , latinam@prosoft-technology.com

5 EtherNet/IP to Modicon S908 Gateway AN-X-MOD The EtherNet/IP to Modicon S908 gateway allows an Allen-Bradley Programmable Automation Controller (PAC) to control Modicon S908 I/O devices. The gateway allows a phased migration approach to be used when upgrading an S908 based Modicon 984, 584, or Quantum control system. The gateway provides automatic creation of the S908 scan-list and generates the associated RSLogix 5000 tags reducing engineering effort. Monitor mode allows verification of your conversion logic using live I/O data without impacting the running legacy system. Once the new PAC is commissioned the legacy I/O can be upgraded one module or one rack at a time as scheduled downtime is available. This gateway minimizes the risk of excessive downtime when upgrading legacy control systems. General Features: Configures through a web browser (No special configuration software required ) Customizable configuration files provide additional flexibility Supports offline configuration through a.csv file Monitor mode enables testing and verification of PAC logic before controlling physical I/O, reducing the risk of production loss due to programming errors View diagnostics with a web browser enabling remote monitoring and troubleshooting Modicon S908 Features: Supports up to 32 Modicon 800, Modicon 200 Series or compatible Quantum I/O drops Auto-Configuration utility discovers and maps racks, modules, and I/O reducing configuration errors There is a configuration option to have the I/O module remember it s last state during a communication loss with the Master Each gateway supports up to 2048 words of Input and 2048 words of Output data Has Module, Drop, and Network level diagnostics enabling effective root cause analysis Supports ControlLogix redundancy applications (Requires 2 gateways) Multi-colored LED that indicates the status of the Modicon network connection

6 EtherNet/IP Features: Supports up to 16 I/O connections for real time control Each connection can have a unique RPI from msec allowing the prioritization of I/O data Auto-Configuration feature maps the discovered Modicon I/O points into tags in the PAC controller. Diagnostic data can be mapped into PAC memory making this data available to HMIs Hardware Specifications Specification Ports Typical Power Consumption Maximum Power Dissapation Operating Temp Storage Temperature Dimensions Humidity Description 1 Modicon F connector 1 RJ45 10/100 Mbps Ethernet port 1 Phoenix 3-pin power connector Vdc or Vdc 2.4W 32 F to 122 F (0 ºC to 50 ºC) -40 F to 185 F (-40 ºC to 85 ºC) 107 mm x 126 mm x 34 mm (4.18 in x 4.97 in x 1.33 in) not including connectors 5% to 95% RH, with no condensation Desktop use or DIN Rail Mountable Ordering Information EtherNet/IP to Modicon S908 Gateway AN-X-MOD How to Contact Us: Sales and Support Sales and Technical Support for this product are provided by ProSoft Technology. Contact our worldwide Sales or Technical Support teams directly by phone or Asia Pacific , asiapc@prosoft-technology.com Europe Middle East Africa +33 (0) , Europe@prosoft-technology.com North America , support@prosoft-technology.com Latin America (Sales only) , latinam@prosoft-technology.com

7 PROFIBUS Multi-Slave or PROFIBUS Network Analyzer Gateway AN-X-PB The PROFIBUS Multi-Slave or PROFIBUS Network Analyzer Gateway has two distinct operational modes. The first mode, PROFIBUS Multi- Slave, enables the transfer of large amounts of data from a PROFIBUS DP Master controller to EtherNet/IP and/or Modbus TCP-enabled PLCs. The Multi-Slave functionality allows up to 15,250 words of Input and Output data to be transferred without requiring multiplexing PLC code to be written in a traditional single slave solution. The second mode, PROFIBUS Network Capture, facilitates the capture, logging, and filtering of packets on a PROFIBUS network without interrupting the running production network. This enables a root cause analysis to be performed on the captured PROFIBUS packets which aids in the identification of complex issue(s). PROFIBUS Multi-Slave Features: Configures through a web browser (No special configuration software required) Configuration option of 1 to 125 PROFIBUS slaves Supports PROFIBUS Baud Rates of 9600 bps - 12 Mbps PROFIBUS Network monitoring tool shows network traffic to and from a user specified node address Ability to view configuration and diagnostics through a web browser enabling remote monitoring or troubleshooting Supports sending up to 250 words of input data, and 248 words of output data on an I/O connection to an Allen-Bradley PLC Supports Class 3 message instructions to move data to Allen-Bradley PLCs Supports up to 16 Modbus TCP client connections Supports Modbus Function Codes 2, 3, 4, 5, 6, 15, 16

8 PROFIBUS Capture Features: Passively monitors all PROFIBUS packets sent across the network Capture file can be configured to use a circular buffer, to capture data for a specific amount of time, or to stop capturing after a specified number of errors have occurred. Filtering options include: Source Address, Destination Address, Frame Control Values, Detailed Status, Frame Data, and Frame CheckSum which enables only the data specified to be logged and displayed A filtering equation can be written to further limit the captured and displayed data Customizable time format Captured data can be saved for future use Passively monitors all PROFIBUS packets sent across the network Hardware Specifications Specification Ports Typical Power Consumption Maximum Power Dissapation Description 1 RJ45 10/100 Mbps Ethernet port for EtherNet/IP connection 1 DB9 serial connector for the PROFIBUS network connection 1 Phoenix 3-pin power connector Vdc or Vdc 3.6W Operating Temp 32 F to 122 F (0º C to 50º C) Storage Temperature Dimensions Humidity -40 F to 185 F (-40º C to 85º C) 107 mm x 126 mm x 34 mm (4.18 in x 4.97 in x 1.33 in) not including connectors 5% to 95% RH, with no condensation Desktop use or DIN Rail Mountable Ordering Information PROFIBUS Multi-Slave or PROFIBUS Network Analyzer Gateway AN-X-PB How to Contact Us: Sales and Support Sales and Technical Support for this product are provided by ProSoft Technology. Contact our worldwide Sales or Technical Support teams directly by phone or Asia Pacific , asiapc@prosoft-technology.com Europe Middle East Africa +33 (0) , Europe@prosoft-technology.com North America , support@prosoft-technology.com Latin America (Sales only) , latinam@prosoft-technology.com October 12, 2016

9 EtherNet/IP to Texas Instruments Remote I/O Master Gateway AN-X-TI The EtherNet/IP to Texas Instruments Remote I/O Master gateway allows an Allen-Bradley Programmable Automation Controller (PAC) to control TI 505 Remote I/O. This gateway allows a phased migration approach to be used when upgrading or replacing TI Remote Base Controllers. The gateway provides automatic creation of the TI Remote I/O scan-list and generates the associated RSLogix 5000 tags reducing engineering effort. Once the new PAC is commissioned the legacy I/O can be upgraded one module or one rack at a time as scheduled downtime is available. This gateway minimizes the risk of excessive downtime when upgrading legacy control systems. TI 505 Features: Configures through a web browser (No special configuration software required) Scans up to 15 Remote I/O bases and supports both high and low density I/O modules Auto-Configuration feature discovers bases and I/O points reducing configuration errors Auto-Configuration files are customizable providing additional flexibility for the application and migration phases Supports offline configuration through a.csv file Ability to view configuration and diagnostics through a web browser enabling remote monitoring or troubleshooting Multi-colored LED that indicates the status of the Remote I/O network connection Please note: To connect this module to an existing coaxial network you will need a RS-485/RF I/O Channel Converter, (PPX: ). It is available from Siemens Industrial Automation Inc. distributors. For assistance in locating your distributor call Reference documents are available for download from

10 EtherNet/IP Features: Supports up to 16 I/O connections to reliably transport data to the PAC Each connection can have a unique RPI from msec allowing the PAC to process the I/O data efficiently Auto-Configuration feature maps the discovered TI 505 I/O points into tags in the PAC controller. Auto-Configuration files are customizable providing additional flexibility for the application and migration phases Ability to view configuration and diagnostics through a web browser enabling remote monitoring or troubleshooting Diagnostic data can be mapped into PAC memory making this data available to HMIs Ethernet network LEDs to show link and activity Hardware Specifications Specification Ports Typical Power Consumption Maximum Power Dissapation Operating Temp Storage Temperature Dimensions Humidity Description 1 DB9 serial connector for the TI network connection 1 RJ45 10/100 Mbps Ethernet port 1 Phoenix 3-pin power connector Vdc or Vdc 3.6W 32 F to 122 F (0 ºC to 50 ºC) -40 F to 185 F (-40 ºC to 85 ºC) 107 mm x 126 mm x 34 mm (4.18 in x 4.97 in x 1.33 in) not including connectors 5% to 95% RH, with no condensation Desktop use or DIN Rail Mountable Ordering Information EtherNet/IP to Texas Instruments Remote I/O Master Gateway AN-X-TI How to Contact Us: Sales and Support Sales and Technical Support for this product are provided by ProSoft Technology. Contact our worldwide Sales or Technical Support teams directly by phone or Asia Pacific , asiapc@prosoft-technology.com Europe Middle East Africa +33 (0) , Europe@prosoft-technology.com North America , support@prosoft-technology.com Latin America (Sales only) , latinam@prosoft-technology.com

11 The AN-X2-AB-DHRIO Gateway is designed to help customers initiate a phased migration approach to replacing or upgrading legacy Remote I/O PLCs, HMI's, Drives or Flex I/O Adapters. These solutions can be achieved by selecting the corresponding operation mode during initial configuration. The AN-X2-AB-DHRIO has a built-in web server that can display diagnostics data, configuration, upload configuration files, and set the operation mode. Note: Now supports DH+ migrations on SLC networks. Some PLC code change may be required see TN DH+ to EIP PV Migration for SLC networks.pdf for more information. DRIVE DATASHEET EtherNet/IP to Remote I/O or DH+ Gateway AN-X2-AB-DHRIO This mode supports upgrading legacy Allen Bradley drives on Remote I/O to new EtherNet/IP enabled drives. No changes to PLC code required Supports up to 4 EtherNet/IP drives Configurable with 1/4, 1/2 and full rack addressing Supports all PowerFlex drives on EtherNet/IP HMI This mode allows legacy PanelViews on Remote I/O or DH+ to be upgraded to a PanelView Plus, PanelView Plus 6 or PanelView Plus 7 on EtherNet/IP. No changes to PLC code required Supports up to 8 PanelViews on the same network Support for DH+ to EtherNet/IP PanelViews upgrades on PLC5 or SLC networks

12 Remote I/O Scanner This mode allows users to replace their existing Remote I/O PLC with a ControlLogix or CompactLogix PAC without having to replace existing racks of I/O. Build new controller program without interrupting existing controls, minimizing downtime Supports up to 32 racks of Remote I/O Supports all Remote I/O baud rates (57.6, 115.2, and K baud), and Remote I/O addressing 0 to 76 octal Works with both ControlLogix or CompactLogix Auto-Configuration utility discovers baud rate and maps discrete I/O reducing configuration errors DH+ This mode acts as a bridge between an EtherNet/IP and a Data Highway Plus network. Programming terminals, and/or processors on an EtherNet/IP network can access legacy processors on a DH+ network Download to a PLC5 or SLC through RSLinx Configures through web browser Supports all DH+ baud rates (57.6, 115.2, and K baud) Communication must be initiated from the EtherNet/IP side, DH+ Messages cannot be sent to EtherNet/IP devices Support for DH+ to EtherNet/IP PanelViews upgrades on PLC5 or SLC networks Flex I/O Scanner This mode allows PLC's on Remote I/O to connect to and control 1794-AENT EtherNet/IP Flex adapters. Designed to replace obsolete 1794-ASB adapters Supports up to 16 EtherNet/IP connections Each adapter and rack of discrete count as a single connection. Each analog module counts as a single connection

13 Hardware Specifications Specification Description Ports Typical Power Consumption Maximum Power Dissipation Operating Temp Storage Temperature Dimensions Humidity Desktop use or DIN Rail Mountable 1 RJ45 10/100 Mbps Ethernet port 1 Phoenix 3-pin power connector 1 Phoenix 3-pin connector network connector VDC or VDC 2.4 W 32 F to 122 F (0 ºC to 50 ºC) -40 F to 185 F (-40 ºC to 85 ºC) 107 x 126 x 34 mm (4.18 x 4.97 x 1.33 in) Not including connectors 5% to 95% RH, with no condensation Where Automation Connects Ordering Information To order this product, please use the following: EtherNet/IP to Remote I/O or DH+ Gateway AN-X2-AB-DHRIO This gateway replaces these part numbers: AN-X-AB-SCAN AN-X-AB-RIO-DRV AN-X-AB-RIO-HMI AN-X-AB-DHP AN-X-AB-ADAPT AN-X-AB-DHRIO To place an order, please contact your local ProSoft Technology distributor. For a list of ProSoft Technology distributors near you, go to: and select Where to Buy from the menu. Copyright 2015 ProSoft Technology, Inc. All Rights Reserved. 9/3/2015 Specifications subject to change without notice.

14 DATASHEET EtherNet/IP to GE Genius I/O Gateway AN-X2-GENI The EtherNet/IP to GE Genius gateway allows an Allen-Bradley Programmable Automation Controller (PAC) to control GE Genius I/O devices. This gateway allows a phased migration approach to be used when upgrading or replacing GE Genius based and controllers. The gateway provides automatic creation of the Genius scanlist and generates the associated RSLogix 5000 tags reducing engineering effort. Monitor mode allows verification of your conversion logic using live I/O data without impacting the running legacy system. Once the new PAC is commissioned the legacy I/O can be upgraded one module or one rack at a time as scheduled downtime is available. This gateway minimizes the risk of excessive downtime when upgrading legacy control systems. Features Configures through a web browser (No separate configuration software required) Customizable configuration files provide additional flexibility Supports offline configuration through a.csv file Monitor mode enables testing and verification of PAC logic before controlling physical I/O, reducing the risk of production loss due to programming errors View diagnostics with a web browser enabling remote monitoring and troubleshooting Micro SD card backs up configuration files - Can be transferred to the unit to minimize downtime in the event of a disaster GE Genius Bus Features Supports sending and receiving Global Data on the Genius Network Supports baud rates: 38.4, 76.8, and Kbps (Standard and Extended) Configurable bus address Auto-Configuration feature discovers and maps up to 31 Genius Blocks of I/O [Online] EtherNet/IP Bus Features Supports up to 16 I/O connections for real time control Supports multicast and unicast connections Each connection can have a unique RPI from 2 to 750 msec allowing the prioritization of I/O data Auto-Configuration feature maps the discovered GE I/O points into tags in the PAC controller Diagnostic data can be mapped into PAC memory making this data available to HMIs

15 Hardware Specifications Specification Description Ports Typical Power Consumption 1 RJ45 10/100 Mbps Ethernet port 1 Phoenix 5-pin GE Genius Bus connector 1 Phoenix 3-pin power connector VDC or VDC Maximum Power Dissapation 2.4W Operating Temp 32 F to 122 F (0 ºC to 50 ºC) Storage Temperature -40 F to 185 F (-40 ºC to 85 ºC) Dimensions 4.18 x 4.97 x 1.33 in 107 x 126 x 34 mm Humidity 5% to 95% RH, with no condensation Regulatory Approvals Visit our web site at for current approval information. Where Automation Connects Global Distribution ProSoft Technology products are distributed and supported worldwide through a network of over 500 distributors in over 50 countries. Our knowledgeable distributors are familiar with your application needs. For a complete list of distributors, go to our web site at: Ordering Information To order this product, please use the following: EtherNet/IP to GE Genius I/O Gateway AN-X2-GENI To place an order, please contact your local ProSoft Technology distributor. For a list of ProSoft Technology distributors near you, go to: and select How to Buy from the menu. Copyright 2014 ProSoft Technology, Inc. All Rights Reserved. 4/7/2014 Specifications subject to change without notice.

16 EtherNet/IP to Reliance AutoMax Gateway AN-X-AMX The AN-X-AMX Gateway provides a migration path for users looking to upgrade Reliance AutoMax DCS or Remote I/O networks. The AMX gateway has multiple operating modes, these operating modes are all included with the AN-X-AMX and are selected during initial module configuration. The operating modes include DCSNet2, a bridge between EtherNet/IP and a DCSNet network; DCSLOG, for logging DCSNet traffic; AMXRIO, a bridge between EtherNet/IP and AutoMax Remote I/O; and AMXCapt, a Remote I/O or DCSNet data capture tool. Migration Specifications DCSNet2 In the DCSNet operating mode, the gateway acts as a bridge between Ethernet/IP and a Reliance AutoMax DCSNet network. The AN-X removes the hardware dependence on specific AutoMax interface cards (ISA, PCI, PC Card) allowing any computer or PAC with Ethernet/IP to connect to a DCSNet network. DCSNet Master or Slave Supports Reliance AutoMax programming software Supports a single I/O connection to a ControLogix processor, DCSNet Supports up to 15 scheduled connections to a ControlLogix processor, DCSNet2 Supports EtherNet/IP HMIs to AutoMax controllers AMXRIO In the AMXRIO operating mode, a PC or PAC Ethernet/IP can connect to a Reliance AutoMax Remote I/O network. The module acts as a master on the AutoMax remote I/O network. Scan up to 7 slave drops Supports up to 248 words of scheduled output data and up to 250 words of scheduled input data Scans AutoMax remote I/O racks and heads Maintains diagnostic counters

17 Troubleshooting Specifications DCSLOG In the DCSLOG operating mode, the gateway connects to the AutoMax DCSNet network, listens to every value of each DCSNet register, looks for changes and then timestamps the values. Data logging with millisecond time stamps Does not occupy a drop on the network or affect existing network traffic AMXCAPT In the AMXCAPT operating mode, data can be captured, stored and then analyzed on a Reliance AutoMax DCS or Remote I/O network. Examine the behavior of all drops, verify network data and timing, locate network errors and troubleshoot problems with the network and with the process. All network frames are captured and stored, with timestamps to microsecond precision Post-capture filtering process to select frames of interest for further analysis Typical capture file size is 2.5 mb/minute, 150 mb/hour, 3.6 gb /day General Specifications Web Access AN-X acts as a web server. Any web browser can connect to the AN-X to view diagnostics and current I/O data. A web browser can be used to configure the drop number and drop depth. Hardware Specifications Specification Ports Typical Power Consumption Maximum Power Dissipation Operating Temp Storage Temperature Dimensions Humidity Description 1 RJ45 10/100 Mbps Ethernet port 1 Phoenix 3-pin power connector 1 DB9 serial connector for the network connection Vdc or Vdc 3.6W 32 F to 122 F (0 ºC to 50 ºC) -40 F to 185 F (-40 ºC to 85 ºC) 107 mm x 126 mm x 34 mm (4.18 in x 4.97 in x 1.33 in) not including connectors Desktop use or DIN Rail Mountable 5% to 95% RH, with no condensation Ordering Information EtherNet/IP to Reliance AutoMax DCS or Remote I/O Gateway AN-X-AMX QTS Part numbers AN-X-DCSNET AN-X-DCSLOG AN-X-AMXRIO AN-X-AMXCAPT How to Contact Us: Sales and Support Sales and Technical Support for this product are provided by ProSoft Technology. Contact our worldwide Sales or Technical Support teams directly by phone or Asia Pacific , asiapc@prosoft-technology.com Europe Middle East Africa +33 (0) , Europe@prosoft-technology.com North America , support@prosoft-technology.com Latin America (Sales only) , latinam@prosoft-technology.com