BehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs
|
|
- Ralph Wilkerson
- 5 years ago
- Views:
Transcription
1 BehringerMods.com Instructions for modification of Behringer SRC analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input upgrades. Steps that are specific to these options will be labelled and can be skipped if you did not purchase them. These modifications require a high level of assembly and skill. It is not recommended for a beginner at electronics. If you doubt your ability to complete the mods correctly, please contact BehringerMods to arrange an installation service. BehringerMods take no responsibility for damage caused to your equipment by modification.
2 Note: The input upgrade has a fixed gain level. The gain knob will only adjust the LED meter after upgrade. The modification package should come with the following parts: Analog Out Mods Populated PCB Ribbon signal cable Ground wire PCB Stands Analog Input Mods Populated PCB Ribbon signal cable Ground wire PCB Stands Ribbon Code: 1) Black = In L + 2) White = In L - 3) Grey = In R + 4) Violet = In R - 5) Blue = V- 6) Green = V+ 7) Yellow = Out L + 8) Orange = Out L - 9) Red = Out R + 10) Brown = Out R -
3 Remove the equipment cover and keep the screws in a dish. Output Upgrade PCB Input Upgrade PCB Place the upgrade PCBs in the case using the self-adhesive stands. Leave space for the ribbon cable plug to enter the PCB.
4 Connect ribbon cables to the upgrade PCBs. Cut the ribbons to length. Input PCB Ribbon should reach the furthest input XLR. NOTE: If installing input and output upgrades together, the Green and Blue wires on the input PCB ribbon need to reach the V+, V- pads on the output PCB. Output PCB ribbon should reach the furthest output XLR. Disconnect all cables and wires to the main PCB, including ground strap.
5 Remove the main PCB. Keep the screws in a dish. Output Upgrade Locate op-amps IC14, IC15 on the rear of the main PCB. Disable both op-amps by cutting the two power legs on each chip. Be carful not to damage the PCB.
6 To disable un-used op-amps the two power legs 4 and 8 (Vcc-, Vcc+) must be cut. Small circle marks the top left of the chip. Use a new sharp blade. Cut towards the chip body, not towards the PCB. Ensure a clear gap at the cut. Be carful, the PCB must not be damaged.
7 Solder the output PCB ribbon wires to the main PCB as shown. Black > Bottom R112 White > Bottom R47 Grey > Bottom R114 Violet > Bottom R113 Cut the back of pins 2 and 3 on each output XLR. Use side-cutters. Leave a clear gap.
8 Solder the wires to the output XLR pins as shown. Yellow > Out L XLR Pin 2 Orange > Out XLR Pin 3 Red > Out R XLR Pin 2 Brown > Out R XLR Pin 3
9 Solder the output PCB ribbon wires as shown. Blue is picking up -15V, Green is picking up +15V. Blue > Top C111 Green > Top C118. If you are only installing the output upgrade, proceed to fitting the analog ground wire near the end of these instructions.
10 Input Upgrade Locate IC7, IC17 and remove them completely. Use a new sharp knife. Cut towards the chip body, not towards the PCB. Cut each chip leg in turn. Support the chip body with your finger. Be carful not to damage the PCB.
11 Remove resistors R48, R49, R132, R133. Remove capacitors C70, C71. Solder input PCB ribbon as shown. Capacitor marking is on the top of the main PCB. Round pad is the positive leg, square pad is the negative leg. Black > C1 Positive Leg Violet > C5 Positive Leg Grey > C6 Positive Leg White > C21 Positive Leg
12 Solder Input PCB ribbon wires as shown. Brown > Bottom R122 Red > Bottom R115 Orange > Top R123 Yellow > Top R24
13 If you are only installing the Input upgrade, connect the Green and Blue wires as shown. If you are installing the Input and Output upgrades together, proceed below. Connect the Input PCB Green and Blue wires as shown. This will chain power from the Output PCB to the Input PCB. Green > Output PCB V+ Pad Blue > Output PCB V- Pad
14 Analog Ground Output upgrade ground. Use the supplied stranded wire to connect: Out L XLR Pin 1 > Output upgrade PCB GND pad. Input upgrade ground. Use the supplied stranded wire to connect: Input upgrade PCB GND pad > Output upgrade PCB GND pad. If you are only installing the Input Upgrade: Connect GND pad > Out L XLR Pin 1.
15 Re-connect all wires and cables. The upgrades should now be complete. Read the instructions again and check your work! Ensure there are no wire cuttings or solder in the case, the soldered wires are not touching other parts and solder has not splashed to the PCBs. Congratulations and enjoy!
MAIN PCB (The small one)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationQRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group. Introduction
QRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a QRPometer. We hope you will enjoy building it and and find it a useful addition to
More informationButton Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System
Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept
More informationMAIN PCB (The small one with the square cut out from one side)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationBuffaloLabs WiFi Lantern Assembly guide version 1
BuffaloLabs WiFi Lantern Assembly guide version 1 Needed equipment: Solder iron Solder wire Cutter Wire stripper (optional) Hot glue gun Overview of the components (not including USB cable and box panels)
More informationSchematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)
Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by
More informationsolutions for teaching and learning
RKP18Motor Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKP18Motor Project PCB Page 1 Description The RKP18Motor project PCB has been designed to use PIC microcontrollers
More informationsolutions for teaching and learning
Circuit Construction Op-Amp Comparator Project The circuit diagram on the right is the circuit for your project, it is called an op-amp comparator circuit, it is called a comparator circuit as it compares
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationUniversal Keying Adapter 3+
Universal Keying Adapter 3+ The Universal Keying Adapter Version 3+ kit will allow you to key nearly any transmitter or transceiver with a straight key, electronic keyer, computer serial or parallel port
More informationElectronics Construction Manual
Electronics Construction Manual MitchElectronics 2019 Version 3 04/02/2019 www.mitchelectronics.co.uk CONTENTS Introduction 3 How To Solder 4 Resistors 5 Capacitors 6 Diodes and LEDs 7 Switches 8 Transistors
More informationConnecting igaging DigiMAG Scales to the Caliper2PC Interface A step by step Guide
What is an igaging DigiMAG Scale? The igaging DigiMAG are digital linear scales that are easily connectable to the Caliper2PC interface. They consist of two parts, the encoder and the readout unit. The
More informationKDS Channel DMX Controlled Servo Kit
KDS00801 8-Channel DMX Controlled Servo Kit This is a DMX512-A controlled servo kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 8-20 VDC @ 50 ma. The board features an
More informationLushOne Inca Synth Module Build Instructions
LushOne Inca Synth Module Build Instructions Getting started If you can build the LushOne base module then then building the Inca should be easy Remember: Accuracy and neatness is more important than speed
More informationElectronics Construction Manual
Electronics Construction Manual MitchElectronics 2018 Version 1 07/05/2018 www.mitchelectronics.co.uk CONTENTS Introduction 3 How To Solder 4 Resistors 5 Capacitors 6 Diodes and LEDs 7 Switches 8 Transistors
More information1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist.
CONSOLE CONNECTOR KIT 8101 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models A-100, D-100, RT2, RT3 LESLIE Speaker Models 122, 122RV KIT CONTENT Console Connector Assembly 047357 Echo Control
More informationThumb Joystick Retail. Tools and parts you'll need. Things you'll want to know. How does it work? Skill Level: Beginner. by MikeGrusin March 22, 2011
Thumb Joystick Retail Skill Level: Beginner by MikeGrusin March 22, 2011 Thank you for purchasing our Thumb Joystick! Whether you're blasting aliens or driving a robot, you'll find it a very useful addition
More informationsolutions for teaching and learning
RKOneAnalogue Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKOneAnalogue Software Development PCB Page 1 Description The RKOneAnalogue software development PCB has been
More informationPhi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012
Phi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012 1. Introduction:... 3 Currently available:... 3 2. Backpack assembly... 4 3. Connecting to a keypad... 6 4. Rotary encoder keypads...
More informationHigh Power (15W + 15W) Stereo Amplifier
High Power (15W + 15W) Stereo Amplifier Build Instructions Issue 1.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit
More informationPICAXE EXPERIMENTER BOARD (AXE090)
(AXE00) Description: The PICAXE experimenter board allows circuits for any size/revision of PICAXE chip ( / / ) to be quickly tested using a prototyping breadboard. The experimenter board provides power
More informationIR TRANSMITTER BLOK PCB ASSEMBLY INSTRUCTIONS. Copyright EduTek Ltd Rev. 2
IR TRANSMITTER BLOK PCB ASSEMBLY INSTRUCTIONS Copyright EduTek Ltd Rev. 2 Circuit Details The circuit is shown below with a parts list of components. Check through this list and identify each component.
More informationStrain gauge Measuring Amplifier GSV-1A8. Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB
Strain gauge Measuring Amplifier GSV-1A8 Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB GSV-1A8USB SubD1 (front side) GSV-1A8USB M12 (front side) GSV-1A16USB (rear side) GSV-1A8USB K6D (front side)
More informationMicrosystems. SCI-6 Sound Card Interface Kit Version 1.09 January 2015
UM Unified Microsystems SCI-6 Sound Card Interface Kit Version 1.09 January 2015 The SCI-6 interface was designed to be a low cost, high quality interface between your PC s sound card and radio transceiver.
More informationPart 2: Building the Controller Board
v3.01, June 2018 1 Part 2: Building the Controller Board Congratulations for making it this far! The controller board uses smaller components than the wing boards, which believe it or not, means that everything
More informationBuild Your Own Home Security System
Build Your Own Home Security System Student Lab Guide Engineering Teaching Laboratory Name Date Lab Partner(s) NEW TERMS Electric Circuit: Electric circuits are paths for transmitting electric current,
More informationVector 3D printer complete wire list including extruder PWA listing
Vector 3D printer complete wire list including extruder PWA listing Conventions Pin numbering for connectors It is normal practice in print circuit board (PCB) layout to denote pin 1 of a PCB mounted connector
More informationKAA Watt x 2 Class-D Audio Amplifier Kit
KAA10021 50 Watt x 2 Class-D Audio Amplifier Kit This amplifier kit uses Texas Instruments TPA3116D2 stereo audio amplifier IC for driving speakers up to 50 watts @ 4 ohm per channel in stereo mode and
More informationVG-305A AC Traffic Light Controller Kit
Galak Electronics Electronic kits and components Website: GalakElectronics.com Email: sales@galakelectronics.com Phone: (302) 832-1978 VG-305A AC Traffic Light Controller Kit Thank you for your purchase
More informationAdvanced Strobe 1.0 Kit
Kit Instruction Manual Eastern Voltage Research, LLC December 2013, Rev 1 1 http://www.easternvoltageresearch.com Kit Introduction to the Kit Thank you for purchasing the Kit. If you are looking for a
More informationChill Interface PCB Assembly Instructions
ExcelValley Chill Interface PCB Waveblaster Module MIDI Interface Board Chill Limited Edition V2 Assembly Kit Standalone midi interface board for Waveblaster synthesizer modules. Suitable for most Waveblaster
More informationKDR00101 DMX Controlled Relay Kit
KDR00101 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 100 ma. The relay contact rating is 10 Amp @ 120 or
More informationInstallation/assembly manual for DCC/Power shield
Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor
More information4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials..
IV PERSONALITY MODULE ASSEMBLY 4.1 Parts and Components............ IV-1 4.2 Assembly Tips............... IV-1 4.3 Assembly Precautions............ IV-1 4.4 Required Tools, Equipment and Materials.. IV-1
More informationConect 121 Upgrade. Copyright 2013 Conqueror Design and Engineering Ltd.
All rights reserved. Any dispute about the use of this software and/or hardware or of these terms and conditions shall be resolved or arbitrated under English Law. Manuals and accompanying documentation
More informationKDR00301 DMX Controlled Relay Kit
KDR00301 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 200 ma. The relay contact rating is 10 Amp @ 120 or
More informationEQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.
EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationEE 354 August 1, 2017 Assembly of the AT89C51CC03 board
EE 354 August 1, 2017 Assembly of the AT89C51CC03 board The AT89C51CC03 board comes as a kit which you must put together. The kit has the following parts: No. ID Description 1 1.5" x 3.25" printed circuit
More informationInstallation Instructions for: Channel Thermocouple Amplifier
Installation Instructions for: 30-2204 4 Channel Thermocouple Amplifier The Advanced Engine Management (AEM) 4 channel thermocouple amplifier revolutionizes temperature measurements by providing laboratory
More informationPost Tenebras Lab. Written By: Post Tenebras Lab
Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.
More informationElectrical Interface 21MTC
Normen Europäischer Modellbahnen Electrical Interface 2MTC NEM 660 Page von 5 Recommendation Dimensions in mm Edition 20 (replacing edition 200). Purpose of Standard This standard defines a Interface which
More informationPacific Antenna Two Tone Generator
Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination
More informationINSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,
More informationXYLOPHONE KIT ESSENTIAL INFORMATION. Version 2.0 CREATE YOUR OWN ELECTRONIC MUSICAL INTRUMENT WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN ELECTRONIC MUSICAL INTRUMENT WITH THIS XYLOPHONE KIT Version 2.0 Build Instructions
More informationDDS Unit Construction Guide of TJ6A pro
DDS Unit Construction Guide of TJ6A pro The main board, PA and the DDS function of TJ6A pro is the same with TJ6A. The different part is the DDS unit in which the S meter unit (SM unit) is add (see picture
More informationGotharman s DIY demoon
Gotharman s DIY demoon Assembly Manual Index Introduction 3 Mainboard Connections 4 Control Panel 5 Assembling The Full Kit 6 Assembling demoon From Mainboard Only 16 Mounting DIY demoon In A Box 18 Troubleshooting
More informationRKP08 Component List and Instructions
RKP08 Component List and Instructions PCB layout Constructed PCB RKP08 Scematic RKP08 Project PCB Page 1 Description The RKP08 project PCB has been designed to use PIC microcontrollers such as the Genie
More informationColecovision 5v Memory Mod Installation
Colecovision 5v Memory Mod Installation The Colecovision suffers from common failure points: the power supply, power switch, and 4116 DRAM. The power supply suffers from poor soldering, the power switch
More informationCP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split. Document revision 2.1 Last modification : 12/11/17
CP5176 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge
More informationShack Clock kit. U3S Rev 2 PCB 1. Introduction
Shack Clock kit U3S Rev 2 PCB 1. Introduction Thank you for purchasing the QRP Labs Shack Clock kit. This clock uses the Ultimate3S QRSS/WSPR kit hardware, but a different firmware version. It can be used
More informationA Backlighted LCD for your K1
A Backlighted LCD for your K1 (K1BKLTKIT) Tom Hammond - NØSS, July 27, 2006 Rev C Thanks to Wayne Burdick, N6KR for suggesting this implementation of backlighting the K1 display. APPLICABILITY This modification
More informationsolutions for teaching and learning
RKAmp1 Component List and Instructions PCB layout Constructed PCB Schematic RKAmp1 Stereo Amplifier Page 1 Description The RKAmp1 stereo amplifier PCB has been designed around the 2 x 1watt stereo amplifier
More informationGSV-1A4 M12/2 M12/2. Highlights
GSV-1A4 M12/2 M12/2 Highlights Input sensitivity: 2mV/V; 4mV/V, 2 mv/v, 1mV/V, 0.5mV/V configurable via jumpers Output signals ±10V AND 12mA+-8mA on 15 pin Sub-D Integrated half and quarter bridge completion
More informationArduino Panel Meter Clock. By Russ Hughes
Arduino Panel Meter Clock By Russ Hughes (russ@owt.com) OVERVIEW My father has been a lifelong Ham Radio Operator with a fondness for almost anything with a panel meter. After seeing the Trinket Powered
More informationBATC Kit MTK2 for MiniTiouner
BATC Kit MTK2 for MiniTiouner Serit FTS4335V NIM Converter Document Change Log 2017-02-22 v1.01 First release 2017-03-01 v1.04 Minor mods Serit FTS4335V, Converter and MiniTiouner (built by G4KLB) Serit
More informationPico Amiga ATX power adaptor install guide
Pico Amiga ATX power adaptor install guide Introduction The ATX power adaptor allows you to power your Amiga A500/A600/A1200 or CD32 from a modern ATX power supply. This variant of the design has a right
More informationPlasma Panel Replacement Guide DU-42PX12X
Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be
More informationConnecting Mitutoyo Digimatic Devices to the Caliper2PC Interface A step by step Guide
Mitutoyo Digimatic Devices Mitutoyo is one of the world's leading manufacturers of precision measuring equipment, offering a huge range of professional products from micrometers, calipers to dial gauges.
More informationInsert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.
MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationHW-101 QSK Modification T/R Relay Replacement
HW-101 QSK Modification T/R Relay Replacement The HW and SB series of transceivers have two 4PDT relays which provide T/R, In this modification, these two relays are replaced by three 2PDT relays. These
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationTubbutec SH-1oh1 µtune
Tubbutec SH-1oh1 µtune Midi retrofit and feature extension for Roland SH-101 Installation Manual http://tubbutec.de 1 Contents Contents 2 1 Installation of the SH-1oh1 mod - µtune edition 3 1.1 Opening
More information!There are two kit models. The ZCTK-120 is designed to operate with.!the pulse output is isolated from the mains line voltage. A pull-up resistor
CAUTION: Please make sure you have or have access to the skills necessary to assemble and use this product. Always secure the case with the included screws before applying electrical power to the power
More informationStrain gauge Measuring Amplifier GSV-1A8. Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB
Strain gauge Measuring Amplifier GSV-A8 Instruction manual GSV-A8, GSV-A8USB, GSV-A6USB GSV-A8USB SubD5 (front side) GSV-A8USB M2 (front side) GSV-A6USB (rear side) GSV-A8USB K6D (front side) Version:
More informationlumentouch SPECIFICATION SHEET Client: Project name: Order #: Type: Qty: FEATURES AND BENEFITS PACKAGE CONTENT HOW TO ORDER LTO
Client: Project name: Order #: Type: Qty: FEATURES AND BENEFITS Flat wall mounted lighting controller Universal mounting plate compatible with any electrical backbox MINI-USB connection for software programming
More informationorban FIELD ENGINEERING BULLETIN Purpose: Units Affected: Replacement Kit, Orban Part # Replacing SSM2017 Op-Amps
orban FIELD ENGINEERING BULLETIN March 27, 2002 Orban Models: 2200, 6200, 6200S, 8200, 8282, 9200 Purpose: Due to the elimination of the SSM2017 by its manufacturer, Orban has had to choose a replacement
More informationUSB-to-I2C. Professional Hardware User s Manual.
USB-to-I2C Professional Hardware User s Manual https://www.i2ctools.com/ Information provided in this document is solely for use with the USB-to-I2C Professional product from SB Solutions, Inc. SB Solutions,
More informationAn ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT
INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0597 Kepco KIT 219-0597 contains the PROMs used to upgrade the firmware for BOP
More informationAssembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement.
NeoLoch NLT-28P-LCD-5S Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. Kit contents: 1 Printed circuit
More informationPacific Antenna Easy TR Switch Kit
Pacific Antenna Easy TR Switch Kit Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate
More informationUSB-to-I2C. Ultra Hardware User s Manual.
USB-to-I2C Ultra Hardware User s Manual https://www.i2ctools.com/ Information provided in this document is solely for use with the USB-to-I2C Ultra product from SB Solutions, Inc. SB Solutions, Inc. reserves
More informationUsing solderless breadboards
Page 1 of 9 Using solderless breadboards This document describes how to use the solderless breadboards available in the experimental didactic lab (LED, previously LADISPE) of Politecnico di Torino. 1 Setting
More informationDENTRON CLIPPERTON-L POWER SUPPLY MODULE v5.3 ASSEMBLY & INSTALLATION INSTRUCTIONS
DENTRON CLIPPERTON-L POWER SUPPLY MODULE v5.3 ASSEMBLY & INSTALLATION INSTRUCTIONS WARNING: This upgrade is not for the faint of heart or inexperienced in amplifier theory and repairs as the voltages inside
More informationMP3 audio amplifier. Build Instructions. Issue 2.0
MP3 audio amplifier Build Instructions Issue 2.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit Board (PCB). The components
More informationME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003
ME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003 This manual and the circuit described have been brought to you by Adam Blankespoor, Roy Merril, and the number 47. The Problem:
More informationCheck that the unit has not been damaged during transport
Check that the unit has not been damaged during transport Protection Against Fire 1. Maintain a minimum of 1 foot distance from any type of flame. 3. Replace fuse only with the specified type and rating.
More informationSM010, Assembly Manual PCB Version 1.0
180 SM010, Assembly Manual MATRIXARCHATE 16 8 IO SEQUENTIAL MATRIX SIGNAL ROUTER SM010 1 2 1 2 3 4 5 3 4 5 6 7 8 9 10 11 12 6 7 8 9 10 11 12 13 14 15 16 PROGRAM A B C D E F G H f1 f2 20.000 180 SSSR Labs
More informationAdvanced Lantern 1.0 Kit. Introduction to the Advanced Lantern 1.0 Kit
Advanced LED Lantern 1.0 Instruction Manual Eastern Voltage Research, LLC Introduction to the Advanced Lantern 1.0 Kit Thank you for purchasing the Advanced Lantern 1.0 Kit. This kit is an advanced microprocessor
More informationDesktop housing AZ/EL Kit V1.2 for ERC-M Instructions. Instructions
Instructions Desktop housing AZ/EL it V1.2 for ERC-M Instructions Congratulations for buying your Desktop housing AZ/EL for ERC-M. This document will guide you through the needed steps for assembly of
More informationInstallation instructions DC Protection and Delay unit, Version 1.2 The package should contain: A piece of normal gauge yellow wire for the AC connect
Installation instructions DC Protection and Delay unit, Version 1.2 How does the unit work? Delay: Basically a capacitor is charged via a resistor, when the voltage of the capacitor reach a certain level,
More informationCasio CZ. Non volatile memory modification Installation instructions version copyright 2013 Artefacts
Casio CZ Non volatile memory modification Installation instructions version 2.0 2017 www.artefacts.nl copyright 2013 Artefacts Introduction The Casio CZ-101 and CZ-1000 do not have a separate backup battery
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationNOTE: Read the instructions completely through before beginning actual installation.
CONSOLE CONNECTOR KIT 7850 INSTALLATION INSTRUCTIONS FOR USE WITH: Various Two-channel Organs LESLIE Speaker Models 705, 705C, 720 KIT CONTENT Console Connector 138488 Switch Assembly, Cable Assembly,
More informationKNJN I2C bus development boards
KNJN I2C bus development boards 2005, 2006, 2007, 2008 KNJN LLC http://www.knjn.com/ Document last revision on December 5, 2008 R22 KNJN I2C bus development boards Page 1 Table of Contents 1 The I2C bus...4
More informationModel ver INSTALLATION MANUAL Rev CHD Elektroservis
Model 8-435 ver. 1.0 INSTALLATION MANUAL Rev. 2 7 2018 CHD Elektroservis Contents page 1 INTRODUCTION.................................................................. 3 1.1 MIDI INTERFACE KIT PARTS.......................................................
More informationQD V LED Tape DMX Driver
4 320W output 1-16ch 24V 4x 5A HP SMD5050 60LED/M MP SMD3528 120LED/M SP SMD3528 60LED/M 60M 60M 20M 30M 60M 110-240VAC Input Voltage IP20 Ingress Protection 24V Output Voltage 4x 5A Max Output Current
More informationdual bipolar voltage controlled step sequencer DIY ASSEMBLY MANUAL v1.03
dual bipolar voltage controlled step sequencer DIY ASSEMBLY MANUAL v1.03 Contents Contents... 2 Introduction... 3 Part Sourcing Notes for Non Kit Builders... 3 Eurorack Kit Assembly... 4 Resistors and
More informationGL2200 MIXING CONSOLE
GL2200 MIXING CONSOLE SYS-LINK EXPANDER OPTION This option connects a GL2200 console as a channel expander to a second console with just one or two interconnecting cables. Kit GL2200-SL1 = SINGLE Single
More informationSRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
More informationParts List: Assembly Instructions:
My Ride SERVICE MANUAl MyRide ASSEMBLY GUIDE 1.1 ASSEMBLY INSTRUCTIONS ASSEMBLING THE MYRIDE Parts List: Heavy Plate Stabilizer Fin - Right Stabilizer Fin - Left Stabilizer Fin - Large Middle Power Cord
More informationRC Tractor Guy Controller V2.1 Assembly Guide
RC Tractor Guy Controller V. Assembly Guide Features 0 Push button inputs Dual axis thumb sticks with built-in push button Rotary encoders with built-in push button MCU Socket to suit Meduino Mega 560
More informationConnections to PAD-LA Series
Connections to PAD-LA Series 1. Control Parameters Four different methods (PAD-LA-1 through PAD-LA-4 connections) can be used to make connections to the PAD-LA series, depending on the control parameters.
More informationConnecting LEDs to the ADB I/O
Application Note AN-2 By Magnus Pettersson September 26 1996 Connecting LEDs to the I/O Introduction The following notes are for those of you who are a bit inexperienced with hardware components. This
More informationDMX CONTROLLED RELAY K8072
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 f the means o ol. y b y la a re 2 protoc Control DMX51 wn well-kno ILLUSTRATED ASSEMBLY MANUAL Total solder
More informationPICAXE CONNECT (AXE210)
PICAXE CONNECT (AXE10) Description: The AXE10 Connect board has been designed as a experimental project board for users wishing to learn how to interface a PICAXE chip to the Maxstream module or a LocSense
More informationInstallation Guide. Version: 6.1 (Digitax 4G) July 2018
Installation Guide Version: 6.1 (Digitax 4G) July 2018 STEP SUMMARY PAGE 1 Fit Mounting Bracket and Antenna 5 2 Connect Primary Loom to Vehicle 5 3 Connect Secondary Loom to Vehicle 8 4 Connect Screen
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationAssembling the Printed Circuit Board for the EDE1200 Robot
This board receives instructions from either a CBL2, a LabPro or (with an adapter cable) an original CBL. The board has two 595 shift registers (each providing 8 bits of on-board memory) and two EDE1200
More informationPower connections 3) Power from 2024 to Control box (The valve harness connected) Ground (0V) +24 V. The voltage between pins 1 & 2 in JPT# 123
Power connections 3) Power from 2024 to Control box (The valve harness connected) The voltage between pins 1 & 2 in JPT# 123 connector should be +24V. 4) Power from 2024 to Control box The voltage between
More informationIQ32 Upgrade Kit Assembly Instructions
IQ32 Upgrade Kit Assembly Instructions Jim Veatch WA2EUJ September 17, 2018 TABLE OF CONTENTS 1. INTRODUCTION... 3 2. IQ-32 UPGRADE KIT INVENTORY... 4 3. PREPARING THE RS-HFIQ AND SIDE PANELS... 6 4. CONNECTING
More information