SESAM USER MANUAL. GeniE Tutorial. Learning the basics and getting started SAFER, SMARTER, GREENER
|
|
- Austen Reed
- 5 years ago
- Views:
Transcription
1 SESAM USER MANUAL GeniE Tutorial Learning the basics and getting started SAFER, SMARTER, GREENER
2 Sesam User Manual GeniE Tutorial - Learning the basics and getting started Date: 9 June 2015 Valid from GeniE V7.1 Prepared by DNV GL - Software support: software.support@dnvgl.com sales: software@dnvgl.com DNV GL AS. All rights reserved This publication or parts thereof may not be reproduced or transmitted in any form or by any means, including copying or recording, without the prior written consent of DNV GL AS.
3 SESAM User Course GeniE Workshop: Learning the basics and getting started Start GeniE by clicking the shortcut on your screen: Create a new workspace (File > New Workspace). Let units be m, kg, N. Create two new sections and name them I600 and I400: Here you have the create/edit section menu. Type in the values for I600 and I400 The values are listed on the next page. Sesam User Manual GeniE - Learning the Basics Page 3
4 I600: Height: 0.6 Width: 0.6 Web: Flange: 0.02 I400: Height: 0.4 Width: 0.4 Web: Flange: 0.02 Sesam User Manual GeniE - Learning the Basics Page 4
5 Now, create a material and name it St44: St44: Yield: Pa Density: 7850 Kg/m^3 Young: 2.1e+011 Poisson: 0.3 Thermal: 1.2e-05 Damping: 0.03 Sesam User Manual GeniE - Learning the Basics Page 5
6 In command line area see that several commands have been read. Also see (upper right area of window) that a default section (I600) and default material (St44) have been defined. Insert a guide plane (Guiding Geometry > Planes >Guide Plane Dialog) with the data shown below (see inside the red circles). Double-click to change See that a guide plane appears. Use the Fit (F9) and View from Y (F7) buttons. Sesam User Manual GeniE - Learning the Basics Page 6
7 Insert beams (section I600) as shown below by clicking Beam button: and then clicking in the guide plane. Change default section to I400 and insert two more beams: Sesam User Manual GeniE - Learning the Basics Page 7
8 Rotate to Iso view (F5). Vertical beams (columns) should be rotated 90º about their axes. Select both beams (first make sure selection button is pressed and then click and shift+click). Use RMB to open Edit Beams dialog. See below. The model should now look like this: Sesam User Manual GeniE - Learning the Basics Page 8
9 See that the beams are listed in the Structure folder in the browser. Change view to Modelling Structure (i.e. don t show guide plane any more). Select all beams by dragging a rubberband. Then use RMB to open the Copy dialog. Make a copy of the frame as shown below (copy in Y-direction). Note that a preview of the copy may be shown by checking the Preview box. Click Apply to perform the copying. Then Cancel the dialog as no more copying is desired. Sesam User Manual GeniE - Learning the Basics Page 9
10 Insert a beam by the straight Beam dialog. Specify appropriate end coordinates as follows: A. Click in the End 1 field (you don t have to delete the data there). B. Click one of the ends of one of the two upper horizontal beams and see that the coordinate (2.5,0,5) pops up in the End 1 field. C. Edit the data of End 1 to (5,0,5). D. Do a similar process for End 2 to get coordinate (5,6,5). A C D B Sesam User Manual GeniE - Learning the Basics Page 10
11 Copy the new beam. Specify the Translation vector of the copy process as follows: A. Click in the Translation vector field. B. Click point 1 and thereafter point 2 and see that the appropriate vector appears. C. Click Apply. A 1 2 Make another copy of the beam to connect the other ends of the two lower horizontal beams. See the resulting model next page. Sesam User Manual GeniE - Learning the Basics Page 11
12 Add supports (Insert > Support > Support Point Dialog) in the four lower corners of the model. Select the supports and use the RMB to open the Properties dialog. Adjust the fixations so that all rotations are free and translations are fixed as indicated by the figure below. For all: Rot X, Y, Z free Z fixed X, Y, Z fixed Y, Z fixed Z fixed Insert a load case name LC1 (Insert > Load Case). See that this appears as the default load case (upper area of the window). Sesam User Manual GeniE - Learning the Basics Page 12
13 Fill LC1 with a point load (Loads > Explicit Load > Point Load) and enter data as shown below. The point p1 is specified by clicking in the field followed by clicking in the model. To see the point load revert from Modelling - Structure view to Default display. Sesam User Manual GeniE - Learning the Basics Page 13
14 Insert a load case name LC2 and see that this appears as the new default load case. Fill LC2 with a line load (Loads > Explicit Load > Line Load) and enter data as shown below. Select points p1 and p2 by clicking the model (insertion point jumps from p1 to p2). Run the analysis: First create an analysis activity: Tools > Analysis > Activity Monitor and click OK. Then click Start in the Activity Monitor. Sesam User Manual GeniE - Learning the Basics Page 14
15 See that analysis succeeded: To view results do as follows: Switch to Results - All or Results with Mesh view. Open the Result presentation dialog (Tools > Analysis > Presentation) and present some results. To see results better switch to Wireframe view: Conclude this workshop by getting familiar with some program basics (graphics, selections, settings, etc.) as explained in a tutorial found as follows: Give Help > Help Topics (F1) to open GeniE help in browser. Click Tutorial 2 General: GeniE Workshop in browser. Try some of the features explained in Part 1 User interface, pages 4 13 and Results, pages Sesam User Manual GeniE - Learning the Basics Page 15
SESAM USER MANUAL. GeniE Tutorial. Semi Pontoon Workshop SAFER, SMARTER, GREENER
SESAM USER MANUAL GeniE Tutorial Semi Pontoon Workshop SAFER, SMARTER, GREENER Sesam User Manual GeniE Tutorial Semi Pontoon Workshop Date: 29 January 2015 Valid from GeniE V7.0 Prepared by DNV GL - Software
More information3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD
3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions
More informationSOFTWARE. Sesam user course. 20 February 2017 HydroD Global Analysis Wadam. Ungraded SAFER, SMARTER, GREENER DNV GL 2014
SOFTWARE Sesam user course DNV GL 1 SAFER, SMARTER, GREENER Scope of presentation Describe commands needed for performing a global analysis of a panel model, and their folders Environment modelling Analysis
More informationInstitute of Mechatronics and Information Systems
EXERCISE 2 Free vibrations of a beam arget Getting familiar with the fundamental issues of free vibrations analysis of elastic medium, with the use of a finite element computation system ANSYS. Program
More informationCreating a T-Spline using a Reference Image
1 / 17 Goals Learn how to create a T-Spline using a Reference Image. 1. Insert an image into the workspace using Attach Canvas. 2. Use Calibrate to set the proper scale for the reference image. 3. Invoke
More information300 N All lengths in meters. Step load applied at time 0.0.
Problem description In this problem, we subject the beam structure of problem 1 to an impact load as shown. 300 N 0.02 0.02 1 All lengths in meters. Step load applied at time 0.0. E = 2.07 10 11 N/m 2
More informationFinite Element Course ANSYS Mechanical Tutorial Tutorial 3 Cantilever Beam
Problem Specification Finite Element Course ANSYS Mechanical Tutorial Tutorial 3 Cantilever Beam Consider the beam in the figure below. It is clamped on the left side and has a point force of 8kN acting
More informationModule 1.7W: Point Loading of a 3D Cantilever Beam
Module 1.7W: Point Loading of a 3D Cantilever Beam Table of Contents Page Number Problem Description 2 Theory 2 Workbench Analysis System 4 Engineering Data 5 Geometry 6 Model 11 Setup 13 Solution 14 Results
More informationThermal Stress Analysis
Thermal Stress Analysis Determine the temperature-induced stresses in a disk brake rotor. Lesson: Thermal Stress Analysis of a Disk Brake Rotor In this exercise we'll perform a Thermal Stress analysis
More informationCreating Multimedia SWF Products
Chapter InDesign can be used to create multimedia products that combine movie clips, sounds, images and animations into professional products that can be distributed on CD, DVD or as SWF files that can
More informationSESAM USER MANUAL WADAM. Wave Analysis by Diffraction and Morison theory. Valid from program version 9.3 SAFER, SMARTER, GREENER
SESAM USER MANUAL WADAM Wave Analysis by Diffraction and Morison theory Valid from program version 9.3 SAFER, SMARTER, GREENER Sesam User Manual Wadam Date: March/2017 Valid from program version 9.3 Prepared
More informationCreating T-Spline Forms
1 / 28 Goals 1. Create a T-Spline Primitive Form 2. Create a T-Spline Revolve Form 3. Create a T-Spline Sweep Form 4. Create a T-Spline Loft Form 2 / 28 Instructions Step 1: Go to the Sculpt workspace
More informationSAFIR training session level 1 Johns Hopkins University, Baltimore. Example: 3D structural model of a beam. 3D steel beam with thermal insulation
SAFIR training session level 1 Johns Hopkins University, Baltimore Example: 3D structural model of a beam 3D steel beam with thermal insulation T. Gernay & J.M. Franssen 3D Beam 1 1. General description
More informationMicrosoft Office Outlook 2007: Intermediate Course 01 Customizing Outlook
Microsoft Office Outlook 2007: Intermediate Course 01 Customizing Outlook Slide 1 Customizing Outlook Course objectives Create a custom toolbar and customize the menu bar; customize the Quick Access toolbar,
More informationGeneral Information Project management Introduction... 4 Getting Started Input geometry... 7
Tutorial Shell Tutorial Shell All information in this document is subject to modification without prior notice. No part or this manual may be reproduced, stored in a database or retrieval system or published,
More informationSAFEGUARDING LIFE, PROPERTY AND THE ENVIRONMENT
SESAM USER MANUAL SESAM MANAGER Managing Sesam Workflow Valid from program version 6.5 SAFEGUARDING LIFE, PROPERTY AND THE ENVIRONMENT SAFER, SMARTER, GREENER Sesam User Manual Sesam Manager Date: 09 May
More informationMaya Lesson 3 Temple Base & Columns
Maya Lesson 3 Temple Base & Columns Make a new Folder inside your Computer Animation Folder and name it: Temple Save using Save As, and select Incremental Save, with 5 Saves. Name: Lesson3Temple YourName.ma
More informationDeveloper s Tip Print to Scale Feature in Slide
Developer s Tip Print to Scale Feature in Slide The latest update to Slide 5.0 brings a number of improvements related to printing functionality, giving the user greater control over printed output. Users
More informationCOMSC-031 Web Site Development- Part 2. Part-Time Instructor: Joenil Mistal
COMSC-031 Web Site Development- Part 2 Part-Time Instructor: Joenil Mistal Chapter 9 9 Creating Pages with Frames You can divide the display area of a Web browser into multiple panes by creating frames.
More informationOasys GSA. Getting Started
Getting Started 13 Fitzroy Street London W1T 4BQ Telephone: +44 (0) 20 7755 3302 Facsimile: +44 (0) 20 7755 3720 Central Square Forth Street Newcastle Upon Tyne NE1 3PL Telephone: +44 (0) 191 238 7559
More informationDOING MORE WITH POWERPOINT: MICROSOFT OFFICE 2013
DOING MORE WITH POWERPOINT: MICROSOFT OFFICE 2013 GETTING STARTED PAGE 02 Prerequisites What You Will Learn USING MICROSOFT POWERPOINT PAGE 03 Slide Views MORE TASKS IN MICROSOFT POWERPOINT PAGE 05 Formatting
More informationStructural static analysis - Analyzing 2D frame
Structural static analysis - Analyzing 2D frame In this tutorial we will analyze 2D frame (see Fig.1) consisting of 2D beams with respect to resistance to two different kinds of loads: (a) the downward
More informationBeginning Tutorial the Lego
Beginning Tutorial the Lego In this tutorial, you will construct a simple hollowed-out block with a hole in it (looks like a Lego). You will learn the basics of creating and modifying sketches and features.
More informationQuestions? Page 1 of 22
Learn the User Interface... 3 Start BluePrint-PCB... 4 Import CAD Design Data... 4 Create a Panel Drawing... 5 Add a Drill Panel... 5 Selecting Objects... 5 Format the Drill Panel... 5 Setting PCB Image
More informationStructural static analysis - Analyzing 2D frame
Structural static analysis - Analyzing 2D frame In this tutorial we will analyze 2D frame (see Fig.1) consisting of 2D beams with respect to resistance to two different kinds of loads: (a) the downward
More informationTekla Structures Analysis Guide. Product version 21.0 March Tekla Corporation
Tekla Structures Analysis Guide Product version 21.0 March 2015 2015 Tekla Corporation Contents 1 Getting started with analysis... 7 1.1 What is an analysis model... 7 Analysis model objects...9 1.2 About
More informationIntroduction And Overview ANSYS, Inc. All rights reserved. 1 ANSYS, Inc. Proprietary
Introduction And Overview 2006 ANSYS, Inc. All rights reserved. 1 ANSYS, Inc. Proprietary The ANSYS Workbench represents more than a general purpose engineering tool. It provides a highly integrated engineering
More informationGetting Started. The main tasks described in this section are the following:
Getting Started Getting Started Before getting into the detailed instructions for using Interactive Drafting workbench, the following tutorial aims at giving you a feel of what you can do with the product.
More informationdraw reference planes click on EQ Parametric Truss STEP 1: from the big R _ scroll over New _ click on Family
Parametric Truss STEP 1: from the big R _ scroll over New _ click on Family STEP 2: select Structural Framing - Complex and Trusses from the list of templates _ click on Open STEP 3: type RP (reference
More informationPrescribed Deformations
u Prescribed Deformations Outline 1 Description 2 Finite Element Model 2.1 Geometry Definition 2.2 Properties 2.3 Boundary Conditions 2.3.1 Constraints 2.3.2 Prescribed Deformation 2.4 Loads 2.4.1 Dead
More informationInventor 201. Work Planes, Features & Constraints: Advanced part features and constraints
Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the
More informationGetting to Integris/SIS
Getting to Integris/SIS Firstly, before installing the app, note a couple of things that might be helpful: a) Maybe an additional keyboard would suit some. b) Don t forget to close Integris the same way
More informationAdjust model for 3D Printing. Scaling 13,0600,1489,1604(SP6)
Adjust model for 3D Printing Scaling 13,0600,1489,1604(SP6) In this exercise, we will learn to create Scaling to added 3DP component. As the printed part cools down, it shrinks. Therefore, it may be required
More information3D SolidWorks Tutorial
ROCHESTER INSTITUTE OF TECHNOLOGY MICROELECTRONIC ENGINEERING 3D SolidWorks Tutorial Dr. Lynn Fuller webpage: http://people.rit.edu/lffeee Electrical and Microelectronic Engineering Rochester Institute
More informationWeb-Friendly Sites. Planning & Design 1
Planning & Design 1 This tutorial presents useful tips and tricks to help you achieve a more Web-friendly design and make your sites more efficient. The following topics are discussed: How Z-order and
More informationSOFTWARE. Sesam user course. 20 February 2017 Wadam - General wave load analysis. Ungraded SAFER, SMARTER, GREENER DNV GL 2014
SOFTWARE Sesam user course DNV GL 1 SAFER, SMARTER, GREENER Wave Analysis by Diffraction And Morison theory Computation of wave loads and global response 2 Diffraction & radiation theory Structural part
More informationLesson: Lightweighting of Robot Gripper Arm
Lesson: Lightweighting of Robot Gripper Arm This functionality is only available in Fusion 360 Ultimate. In this exercise we'll perform a Shape Optimization study to reduce the weight of a robot gripper
More informationWHITEPAPER FLOATOVER ANALYSIS. From modelling to time-domain analysis using Sesam TM SAFER, SMARTER, GREENER
WHITEPAPER FLOATOVER ANALYSIS From modelling to time-domain analysis using Sesam TM SAFER, SMARTER, GREENER Reference to part of this report which may lead to misinterpretation is not permissible. No.
More informationManaging Content with AutoCAD DesignCenter
Managing Content with AutoCAD DesignCenter In This Chapter 14 This chapter introduces AutoCAD DesignCenter. You can now locate and organize drawing data and insert blocks, layers, external references,
More informationVisualART 2018 Quick Start Guide MecSoft Corporation
2 Table of Contents About this Guide 3 1 About... the ART Module 3 2 Using this... Guide 3 3 Useful... Tips 4 Getting Ready 5 1 Running... VisualCAD 5 2 About... the VisualCAD Display 5 3 Launching...
More informationExcel 2003 Tutorial II
This tutorial was adapted from a tutorial by see its complete version at http://www.fgcu.edu/support/office2000/excel/index.html Excel 2003 Tutorial II Charts Chart Wizard Chart toolbar Resizing a chart
More informationVisualCAM 2018 for SOLIDWORKS-TURN Quick Start MecSoft Corporation
2 Table of Contents Useful Tips 4 What's New 5 Videos & Guides 6 About this Guide 8 About... the TURN Module 8 Using this... Guide 8 Getting Ready 10 Running... VisualCAM for SOLIDWORKS 10 Machining...
More informationExercise Guide. Published: August MecSoft Corpotation
VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4
More informationCS3240 Human-Computer Interaction Lab Sheet Lab Session 2
CS3240 Human-Computer Interaction Lab Sheet Lab Session 2 Key Features of Silverlight Page 1 Overview In this lab, you will get familiarized with the key features of Silverlight, such as layout containers,
More informationAppendix B: Creating and Analyzing a Simple Model in Abaqus/CAE
Getting Started with Abaqus: Interactive Edition Appendix B: Creating and Analyzing a Simple Model in Abaqus/CAE The following section is a basic tutorial for the experienced Abaqus user. It leads you
More information0 Graphical Analysis Use of Excel
Lab 0 Graphical Analysis Use of Excel What You Need To Know: This lab is to familiarize you with the graphing ability of excels. You will be plotting data set, curve fitting and using error bars on the
More informationAutodesk Inventor - Basics Tutorial Exercise 1
Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be
More informationNotes on Blender: By Matthew Evett
Notes on Blender: By Matthew Evett A synopsis of the Wiki: http://en.wikibooks.org/wiki/blender_3d:_noob_to_pro The Blender GUI is implemented via opengl. Thus the GUI is not Windowsstandard. Can resize
More informationQuick Start Guide. for RhinoCAM-ART Published: December MecSoft Corpotation
Quick Start Guide for RhinoCAM-ART 2019 Published: December 2018 MecSoft Corpotation Copyright 1998-2018 RhinoART 2019 Quick Start Guide by MecSoft Corporation User Notes: Contents 2 Table of Contents
More informationIntroduction Make a plan with tool Rectangle Measurements Toolbar Enter Return Measurements Toolbar Measure Protractor
Introduction Open SketchUp, and an empty file appears. You are looking at the red-green plane, and the blue axis (vertical) is pointing toward you. By default, you are in the Line tool, as indicated by
More informationLab - Introduction to Finite Element Methods and MATLAB s PDEtoolbox
Scientific Computing III 1 (15) Institutionen för informationsteknologi Beräkningsvetenskap Besöksadress: ITC hus 2, Polacksbacken Lägerhyddsvägen 2 Postadress: Box 337 751 05 Uppsala Telefon: 018 471
More information300 N All lengths in meters. Step load applied at time 0.0. The beam is initially undeformed and at rest.
Problem description In this problem, we subject the beam structure of problem 1 to an impact load as shown. 300 N 0.02 0.02 1 All lengths in meters. Step load applied at time 0.0. E = 2.07 10 11 N/m 2
More informationEquipment Support Structures
Equipment Support Structures Overview Conventions What's New? Getting Started Setting Up Your Session Creating a Simple Structural Frame Creating Non-uniform Columns Creating Plates with Openings Bracing
More informationModule 4B: Creating Sheet Metal Parts Enclosing The 3D Space of Right and Oblique Pyramids With The Work Surface of Derived Parts
Inventor (5) Module 4B: 4B- 1 Module 4B: Creating Sheet Metal Parts Enclosing The 3D Space of Right and Oblique Pyramids With The Work Surface of Derived Parts In Module 4B, we will learn how to create
More informationBobCAD-CAM FAQ #50: How do I use a rotary 4th axis on a mill?
BobCAD-CAM FAQ #50: How do I use a rotary 4th axis on a mill? Q: I ve read FAQ #46 on how to set up my milling machine. How do I enable 4th axis to actually use it? A: Enabling 4th axis in the machine
More informationIntroduction To Finite Element Analysis
Creating a Part In this part of the tutorial we will introduce you to some basic modelling concepts. If you are already familiar with modelling in Pro Engineer you will find this section very easy. Before
More informationClose Using Quick Launch Toolbar 05 Close Using Size Option 05. Quick Launch Toolbar 07. Properties 08 Preview 09 Tool Menu & Properties 09
Contents Open Card Designer 05 Close Card Designer 05 Close Using Quick Launch Toolbar 05 Close Using Size Option 05 Card Designer Menu & Functions 06 Quick Launch Toolbar 07 1 New 07 2 Open 07 3 Save
More informationEquipment Support Structures
Page 1 Equipment Support Structures Preface Using This Guide Where to Find More Information Conventions What's New? Getting Started Setting Up Your Session Creating a Simple Structural Frame Creating Non-uniform
More informationTransforming Objects in Inkscape Transform Menu. Move
Transforming Objects in Inkscape Transform Menu Many of the tools for transforming objects are located in the Transform menu. (You can open the menu in Object > Transform, or by clicking SHIFT+CTRL+M.)
More informationMOBILOUS INC, All rights reserved
8-step process to build an app IDEA SKETCH CONCEPTUALISE ORGANISE BUILD TEST RELEASE SUBMIT 2 I want to create a Mobile App of my company which only shows my company information and the information of
More informationTechnique or Feature Where Introduced
Part 6: Keypad 4 Mirrored features Patterned features First extrusion Rounded corners In the earpiece part, you defined a radial pattern, one that created new instances of a feature at intervals around
More informationLabel Printing Software BA-300 Version 1.00
Label Printing Software BA-300 Version 1.00 EN For Windows User s Guide What you can do with the BA-300 Application Using the BA-300 Application Troubleshooting Be sure to keep all user documentation handy
More informationProblem description. The FCBI-C element is used in the fluid part of the model.
Problem description This tutorial illustrates the use of ADINA for analyzing the fluid-structure interaction (FSI) behavior of a flexible splitter behind a 2D cylinder and the surrounding fluid in a channel.
More informationThe playhead, shown as a vertical red beam, passes each frame when a movie plays back, much like movie fi lm passing in front of a projector bulb.
The project: AIRPLANE I will show you a completed version of this project.. Introducing keyframes and the Timeline One of the most important panels in the Flash workspace is the Timeline, which is where
More informationMaster Pages. Basics 1
Basics 1 Some elements of your design will appear on every page of your publication. For a professional look, these elements should be placed consistently from page to page. By using master pages, you
More informationXnView 1.9. a ZOOMERS guide. Introduction...2 Browser Mode... 5 Image View Mode...15 Printing Image Editing...28 Configuration...
XnView 1.9 a ZOOMERS guide Introduction...2 Browser Mode... 5 Image View Mode...15 Printing... 22 Image Editing...28 Configuration... 36 Written by Chorlton Workshop for hsbp Introduction This is a guide
More informationsolidthinking User Interface
Lesson 1 solidthinking User Interface This lesson introduces you to the solidthinking interface. The functions described represent the tools necessary for effectively managing the modeling of a project.
More informationAnalysis Steps 1. Start Abaqus and choose to create a new model database
Source: Online tutorials for ABAQUS Problem Description The two dimensional bridge structure, which consists of steel T sections (b=0.25, h=0.25, I=0.125, t f =t w =0.05), is simply supported at its lower
More informationKratos Multi-Physics 3D Fluid Analysis Tutorial. Pooyan Dadvand Jordi Cotela Kratos Team
Kratos Multi-Physics 3D Fluid Analysis Tutorial Pooyan Dadvand Jordi Cotela Kratos Team Kratos 3D Fluid Tutorial In this tutorial we will solve a simple example using GiD and Kratos Geometry Input data
More informationEnd User Guide. 2.1 Getting Started Toolbar Right-click Contextual Menu Navigation Panels... 2
TABLE OF CONTENTS 1 OVERVIEW...1 2 WEB VIEWER DEMO ON DESKTOP...1 2.1 Getting Started... 1 2.1.1 Toolbar... 1 2.1.2 Right-click Contextual Menu... 2 2.1.3 Navigation Panels... 2 2.1.4 Floating Toolbar...
More informationModeling Evaporating Liquid Spray
Tutorial 17. Modeling Evaporating Liquid Spray Introduction In this tutorial, the air-blast atomizer model in ANSYS FLUENT is used to predict the behavior of an evaporating methanol spray. Initially, the
More informationInstitute of Mechatronics and Information Systems
EXERCISE 4 Free vibrations of an electrical machine model Target Getting familiar with the fundamental issues of free vibrations analysis of a simplified model of an electrical machine, with the use of
More informationExtrude. Taper. STEP 04: Ctrl +V _ select Copy from the clone window _ name the copy: Slabs Mesh _ click OK
Extrude STEP 01: open the class-08 3ds Max file _ select the ellipse _ command panel / modifier list _ select Extrude _ set the extrusion Amount: 400 _ STEP 02: with the perspective viewport current press
More informationQuick Start Guide. for VisualCAM-ART Published: December MecSoft Corpotation
Quick Start Guide for VisualCAM-ART 2019 Published: December 2018 MecSoft Corpotation Copyright 1998-2018 VisualART 2019 Quick Start Guide by MecSoft Corporation User Notes: Contents 2 Table of Contents
More informationANSYS Workbench Guide
ANSYS Workbench Guide Introduction This document serves as a step-by-step guide for conducting a Finite Element Analysis (FEA) using ANSYS Workbench. It will cover the use of the simulation package through
More informationThe Generate toolbar has convenient tools to create typical structural shapes.
Frame Analysis Using Multiframe 1. The software is on the computers in the College of Architecture in Programs under the Windows Start menu (see https://wikis.arch.tamu.edu/display/helpdesk/computer+accounts
More informationCropping an Image for the Web
Cropping an Image for the Web This guide covers how to use the Paint software included with Microsoft Windows to crop images for use on a web page. Opening Microsoft Paint (In Windows Accessories) On your
More informationXnView Image Viewer. a ZOOMERS guide
XnView Image Viewer a ZOOMERS guide Introduction...2 Browser Mode... 5 Image View Mode...14 Printing... 22 Image Editing...26 Configuration... 34 Note that this guide is for XnView version 1.8. The current
More informationBP-VA Quick Start. Last update: 29 th January, Copyright Visual Paradigm International Ltd.
BP-VA Quick Start Last update: 29 th January, 2010 Copyright 2002-2010 Visual Paradigm International Ltd. Table of Contents Table of Contents... 2 Getting started... 3 Installing Business Process Visual
More informationEN1740 Computer Aided Visualization and Design Spring /26/2012 Brian C. P. Burke
EN1740 Computer Aided Visualization and Design Spring 2012 4/26/2012 Brian C. P. Burke Last time: More motion analysis with Pro/E Tonight: Introduction to external analysis products ABAQUS External Analysis
More informationVersion October 2015 RFEM 5. Spatial Models Calculated acc. to Finite Element Method. Introductory Example
Version October 2015 Program RFEM 5 Spatial Models Calculated acc. to Finite Element Method Introductory Example All rights, including those of translations, are reserved. No portion of this book may be
More informationTekla StruXML Export. User s Guide to Tekla Structures - FEM-Design Integration
Tekla StruXML Export User s Guide to Tekla Structures - FEM-Design Integration StruSoft AB www.strusoft.com Version: August 1st, 2018 Copyright Copyright 2018 by StruSoft. All rights reserved. Content
More information2D Tutorial. Project Description: Running VisualAnalysis: Setting Up the Project:
2D Tutorial Project Description: This project has been set-up to demonstrate the basic features of VisualAnalysis. You will model and analyze the following two-dimensional frame with a curved glue-laminated
More informationWORLDWIDE PANTS COLLECTION USER GUIDE! As of ! For best results, use Google Chrome as the recommended web browser.!
WORLDWIDE PANTS COLLECTION USER GUIDE As of 3-19-15 For best results, use Google Chrome as the recommended web browser. NEW USER REGISTRATION 1. First time users will need to create an account. To create
More informationAutodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Tim Varner - 2004 The Inventor User Interface Command Panel Lists the commands that are currently
More informationUsing LCS Help. In This Section
Using LCS Help We want to help you get the most out of Square D Lighting Control Software (LCS) system by Schneider Electric. This Help system contains most of the information you'll need to successfully
More information3D Body. Summary. Modified by Admin on Sep 13, Parent page: Objects
3D Body Old Content - visit altium.com/documentation Modified by Admin on Sep 13, 2017 Parent page: Objects A sphere, a cylinder and 4 extruded rectangles have been used to create the 3D body for an LED.
More informationArtistic Text. Basics 1
Basics 1 In this tutorial, we ll show you how to: Work with artistic text. Create, edit, and format text. Apply shadows, reflections, and other text effects. Create shaped text (or text-on-a-path). 2 Basics
More information1.1: Introduction to Fusion 360
.: Introduction to Fusion 360 Fusion 360 is a cloud- based CAD/CAM tool for collaborative product development. The tools in Fusion enable exploration and iteration on product ideas and collaboration within
More informationModule 1.6: Distributed Loading of a 2D Cantilever Beam
Module 1.6: Distributed Loading of a 2D Cantilever Beam Table of Contents Page Number Problem Description 2 Theory 2 Geometry 4 Preprocessor 7 Element Type 7 Real Constants and Material Properties 8 Meshing
More informationTutorial by Philemon Yalamu
Date: 27 th March 204 Tutorial by Philemon Yalamu http://www.artech.com.pg/ Introduction Adobe Audition is a professional audio editing program that works well with other programs in the Adobe Creative
More informationBeginning Paint 3D A Step by Step Tutorial. By Len Nasman
A Step by Step Tutorial By Len Nasman Table of Contents Introduction... 3 The Paint 3D User Interface...4 Creating 2D Shapes...5 Drawing Lines with Paint 3D...6 Straight Lines...6 Multi-Point Curves...6
More informationFOUNDATION IN OVERCONSOLIDATED CLAY
1 FOUNDATION IN OVERCONSOLIDATED CLAY In this chapter a first application of PLAXIS 3D is considered, namely the settlement of a foundation in clay. This is the first step in becoming familiar with the
More informationVisualMILL Getting Started Guide
VisualMILL Getting Started Guide Welcome to VisualMILL Getting Started Guide... 4 About this Guide... 4 Where to go for more help... 4 Tutorial 1: Machining a Gasket... 5 Introduction... 6 Preparing the
More informationMASTERCAM DYNAMIC MILLING TUTORIAL. June 2018
MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject
More informationUsing Adobe Contribute 4 A guide for new website authors
Using Adobe Contribute 4 A guide for new website authors Adobe Contribute allows you to easily update websites without any knowledge of HTML. This handout will provide an introduction to Adobe Contribute
More informationModeling a Gear Standard Tools, Surface Tools Solid Tool View, Trackball, Show-Hide Snaps Window 1-1
Modeling a Gear This tutorial describes how to create a toothed gear. It combines using wireframe, solid, and surface modeling together to create a part. The model was created in standard units. To begin,
More informationTutorial: Riser Simulation Using Dense Discrete Phase Model
Introduction The purpose of this tutorial is to demonstrate the setup of a dense discrete phase model (DDPM) with the example of 2D riser. DDPM is used for the secondary phase that has a particle size
More informationAutodesk Fusion 360 Training: The Future of Making Things Attendee Guide
Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Abstract After completing this workshop, you will have a basic understanding of editing 3D models using Autodesk Fusion 360 TM to
More informationSema Foundation ICT Department. Lesson - 18
Lesson - 18 1 Manipulating Windows We can work with several programs at a time in Windows. To make working with several programs at once very easy, we can change the size of the windows by: maximize minimize
More information