Mikrokopter FPV Camera Mount. Assembly Manual
|
|
- Clementine Shelton
- 5 years ago
- Views:
Transcription
1 Assembly Manual Introduction Thank you for purchasing the. The FPV Camera Mount is provided as a kit and requires assembly. The assembly of the mount can take up to minutes for an inexperienced builder. Before starting to assemble the kit, please examine your kit that is has all the necessary parts and nothing is missing. Please see the list of the items on the next page to make sure everything is in the bag: Page 1 of 7
2 Content: 1 x 1.6mm FR4 (fibreglass) mounting plate 1 x Camera Plate 1 x Camera Spindle 1 x Drilling guide 2 x Side mounts 9 x 4-40 wood screws 1 x 4-40 black metal screw 1 x 1mm pushrod If any of the above is missing please contact us at customerservice@nghobbies.com for replacement parts. Items required and not supplied: 1 x Camera 1 or 2 strips of double sided tape 1 x Hitec HS55 servo or similar Tools required: The following tools will be required for assembly: Needle nose plier Philips screwdriver 3/32 or 2.5mm drill bit Portable hand drill Hobby cutter Page 2 of 7
3 Step 1: Take the drilling guide and push it on the camera spindle just like in the picture below. It should be tight. Make sure the edges are lined up and the guide is properly level with the spindles edges. Use the hand-drill and the drill-bit to drill 2 holes in the spindle guided by the drilling guide. Try to make it as straight as possible and make sure you drill in at least ½ inches about 12-13mm. Step 2: Assemble the side parts. Using 4 wood screws just like in the picture below assemble the 2 sides of the camera mount. Please make sure you do not overtighten the screws. Step 3: Install the spindle using the black metal screw. You will have to push hard on the screw when screwing it in as the bottom hole is drilled to be tight. Page 3 of 7
4 Step 4: Using the hobby knife cut the camera plate to the size of the camera. The camera plate provided has a few milled guides for 20mm, 25mm and 30mm cameras. Please use these guides to cut down the camera plate to the dimensions of your camera. Step 5: Using the hobby knife cut an opening for the camera connector. The plastic is soft, please make sure you cut it slow and with care, otherwise you can run the knife trough cutting out a whole unwanted part. Line up the camera with the plate, mark the portion where the opening has to be cut and cut it out using the hobby knife. Step 6: Install the camera plate on the spindle. Take 2 of the remaining wood screws and install the camera plate on the spindle such that the edge overflows on the bottom side. Here if you did not drill in deep enough you will have to drill in again deeper. The top edge of the camera plate has to be flush with the camera spindle. Page 4 of 7
5 Step 7: Install the camera mount on the mounting plate. The mounting plate has holes pre-drilled. The assembled camera mount however will need 3 holes drilled for the camera plate. For your convenience there were some hole guides milled in the 2 side mounts, so when these are pressed and held together by the screws it will provide a good starting point for the drill bit. Please try to drill these holes as straight as possible. You should drill in at least 1/2 deep to accommodate the length of the screws. Step 8: Cutting the length of the middle mounting screw. When the middle screw is inserted, it will pass into the servo mounting hole. This is not acceptable as the servo will not fit in with the tip of the screw peaking out. Remove the middle screw and using a wire cutter cut back about 2mm from the length. For better mounting and eliminating more vibrations a double-sided tape can be inserted between the camera mount and the holding plate. In this case the screw might not stick out on the bottom and the above step might not be needed. The following picture illustrates such a solution: Page 5 of 7
6 Step 9: The pushrod provided in the package will have to be bent such that it will provide full motion range for the servo installed in the mount. While the pictures do not illustrate, we recommend bending the pushrod to the necessary length only after the servo is installed and the servo horn is mounted. The following pictures are only a guide to how the pushrod should be bent: Step 10: Mounting the camera. The camera is mounted with a double-sided tape to the camera plate. Using a 150 grid sandpaper the user should sand the camera plate a bit before pushing the double-sided sticky tape on it. This will provide additional adherence. For added security zipties should be used to secure the camera to the camera plate. An example of a simple mounting is in the following picture: Step 11: Mounting the camera mount on the Mikrokopter. There are 2 different versions. The Quadrokopter version comes with a mounting plate which is illustrated throughout this documentation. The user will have to use 4 plastic standoffs on the bottom holes of the Flexlander L landing gear. The holes on the quad plate will match this distance and it can be mounted with 4 3x8mm screws underneath the Mikrokopter quadro. This mounting leaves Page 6 of 7
7 space for battery installation and removal as well as the long holes on the mounting plate allow installation of video transmitters, video batteries, etc. If you choose the Hexa or Okto version, this kit comes with a mounting plate which replaces the bottom battery holder (or Highsight holder plate) plate for the Mikrokopter Hexa and Okto. If one requires, the original plate can be left in place and instead of the M3Plastic nuts 15 or 15mm standoffs can be used to provide an additional stacking layer with this mount ,,. Page 7 of 7
A B C D REV 1 SHEET 1 OF 1 1 G NO assy_011 DW TITLE SIZE C SCALE 9/17/2016 N 2 2 FG APPROVED CHECKED QA M Henri DRAW PHALANX A B C D
4 A BPHALANX Greetings and good fortune be on you as you have aquired your new greatness. As you work through the assembly passages, please, READ THE DIRECTIONS! There are fine points covered that you
More informationUpgrade Instructions. P/N Revision A. October Printer Terminal Holder * *
Upgrade Instructions P/N 96-08-0 Revision A October 000 480 Printer Terminal Holder P/N 96-08-0 Revision A *96080* Instructions This terminal holder connects the INTERMEC R 600 Series and 700 Series Computers
More informationConstructing a Low-Cost Mobile Eye Tracker
==== Constructing a Low-Cost Mobile Eye Tracker ==== Section 1: Introduction This is a detailed set of instructions on how to build a low-cost mobile eye-tracking system from off-the-shelf components.
More informationElecraft W1 SWR/Wattmeter Enclosure by W8FGU
Elecraft W1 SWR/Wattmeter Enclosure by W8FGU The W1 enclosure is made of Lexan, a polycarbonate, which is very strong. It also has a UV blocking coating on one side and was assembled carefully with this
More informationVac-U-Cam. R/C Camera Boat Hull Kit. Length: 22.5 in. Beam: 7 in. Draft: 2-3/8 in. Displacement: 4 lb.
Vac-U-Cam TM R/C Camera Boat Hull Kit Length: 22.5 in. Beam: 7 in. Draft: 2-3/8 in. Displacement: 4 lb. A stable camera platform for use with digital cameras, or waterproof cameras up to 16 ounces. A 3-channel
More informationPARTS LIST 1 x PC Board 36 x 5mm Red LED 36 x 12mm LED Standoff 36 x NPN Transistor 36 x 10kΩ Resistor OTHER PARTS YOU MAY NEED
PARTS LIST 1 x PC Board 36 x 5mm Red LED 36 x 12mm LED Standoff 36 x NPN Transistor 36 x 150Ω Resistor 36 x 10kΩ Resistor 17 x Mini Toggle on-off 8 x Mini Toggle (on)-off-(on) 1 x 470Ω Resistor 1 x 47µF
More informationUpgrade Instructions Printer Terminal Holder
Upgrade Instructions 6820 Printer Terminal Holder Instructions Terminal Holder Installation Kit The terminal holder connects INTERMEC R computers to the 6820 Printer. Do these instructions, in the order
More informationMicroscope with original illuminator. Microscope with Nanodyne replacement illuminator.
Nanodyne Replacement Illuminator for Zeiss xioskop Microscope Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Copyright 09 Nanodyne Measurement Systems. Document
More informationSingle cable kit for the FCB1010
Single cable kit for the FCB1010 1. What is it? With this kit, you can turn your FCB1010 into a phantom powered floorboard, which can do 2-way MIDI communication over one single cable. After installing
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationMini FPV Tricopter / Vtail / Quadcopter
Mini FPV Tricopter / Vtail / Quadcopter Frame Assembly Manual / Tips and Tricks Armattan Minis Website: http://www.armattanminis.ca/ Main Armattan Website (doesn t have minis): http://www.armattanquads.com/
More informationREMOTE HEAD ADAPTER INSTALLATION GUIDE
REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and
More informationAsus ZenFone 2 Motherboard Replacement
Asus ZenFone 2 Motherboard Replacement If you have problems with your phone rebooting at random times, you could have a faulty motherboard in your phone. Written By: Eduardo Nodarse ifixit CC BY-NC-SA
More informationimac Intel 27" EMC 2639 Hard Drive
imac Intel 27" EMC 2639 Hard Drive Replacement Replace the Hard Drive in your imac Intel 27" EMC 2639. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replacing the
More informationipad Mini 2 Wi-Fi Front Panel Assembly Replacement
ipad Mini 2 Wi-Fi Front Panel Assembly Replacement Fix a broken ipad Mini 2 screen. Replace the front glass and digitizer on an ipad Mini 2 Wi-Fi. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com
More informationCINTENNA ANTENNA REPAIR GUIDE
The Cintenna is a great tool when looking to transmit WIRELESS DMX data over obstacles or hard to reach places. Wireless DMX can have its issues when not having a good line of sight between the transmitter
More informationBitty Rover. Recommended Age: 12 and up Difficulty Level: 3/5 (Soldering Required, programming, connecting wires, small parts choking hazard)
Bitty Rover Bitty Rover V2.3 Assembly Instructions Recommended Age: 12 and up Difficulty Level: 3/5 (Soldering Required, programming, connecting wires, small parts choking hazard) www.rabbitrobots.com
More informationUser s Guide TURBO Pinewood Derby Finish Line and Timer Release /31/2011 NewBold Products, Atlanta GA
User s Guide TURBO Pinewood Derby Finish Line and Timer Release 2.1 12/31/2011 NewBold Products, Atlanta GA www.newboldproducts.com 2 1. YOUR SHIPMENT Thank you for purchasing the TURBO, Pinewood Derby
More informationHQuad500 Frame Assembly Guide
HQuad500 Frame Assembly Guide V1.0 June 2015 1 What s Included Kit Content Hardware Bag Content 2 HQuad500 Assembly 2.1 Arm & Motor Mount Sub Assembly 2.2 Landing Gear Step 1 2.3 Center Plates Sub Assembly
More informationReference Manual VL-ENCL-5. Development Enclosure DOC. REV. 4/9/2013
Reference Manual DOC. REV. 4/9/2013 VL-ENCL-5 Development Enclosure WWW.VERSALOGIC.COM 12100 SW Tualatin Road Tualatin, OR 97062-7341 (503) 747-2261 Fax (971) 224-4708 Contents Copyright 2013 All Rights
More informationUpgrading the programmer supply unit of the BeeProg+/BeeProg2 programmer
Upgrading the 50-0033 programmer supply unit of the BeeProg+/BeeProg2 programmer How-Do-It Manual December 2012 BeeProgX_50-0033_PSU1_upgrade_manual, version 1.31 page 1 Introduction This how-do-it manual
More informationTHE HP P2015 TONER CARTRIDGE
THE HP P2015 TONER CARTRIDGE DOC# 0379 By Mike Josiah and the Technical Staff at Summit Technologies HP LASERJET P2015 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS Page 1 Remanufacturing the HP P2015 Toner
More informationUse flat head screws for the out side of chassis and pan head screw for inside of chassis.
These are instructions are guidelines in building a Storage Pod. 2-a Use flat head screws for the out side of chassis and pan head screw for inside of chassis. 1. Take the main chassis and check the chassis
More informationWritten By: Sam Lionheart
ipad Mini 2 Wi-Fi GPS Antenna Replacement Remove the GPS antenna in an ipad Mini 2 Wi-Fi. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 36 INTRODUCTION Use this guide to replace
More informationFPV racer Frame class:
By FPV racer Frame class: Prop. size: Motor size: Power: Flight Cam: Material: 250 Up to 6" M3 or M2 attached motors of choice Up to 4S 1500 mah housed inside frame as optimum, depending on brand Tie-strap
More informationFCB1010 Phantom Power Adaptor
FCB1010 Phantom Power Adaptor The Behringer FCB1010 pedal is normally powered by an external cable that plugs into a standard 120 volt 3-prong wall receptacle. While this works fine, it does require a
More informationHow to build an Olympus D-360L Trail Camera using the PixController Universal "Digital Trail Camera Kit" w/ RS-232-U PIC Chip
Copyright, PixController, Inc. http://www.pixcontroller.com, all rights reserved. How to build an Olympus D-360L Trail Camera using the PixController Universal "Digital Trail Camera Kit" w/ RS-232-U PIC
More information1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist.
CONSOLE CONNECTOR KIT 8101 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models A-100, D-100, RT2, RT3 LESLIE Speaker Models 122, 122RV KIT CONTENT Console Connector Assembly 047357 Echo Control
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationHow to Perform an IBM ThinkPad X60s Fan Spindle Replacement
How to Perform an IBM ThinkPad X60s Fan Spindle Replacement This guide details an IBM ThinkPad X60s fan spindle replacement. Written By: Samuel Lees ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION
More informationHow to hardwire the Olympus D-370 and D-380 Digital Cameras
How to hardwire the Olympus D-370 and D-380 Digital Cameras Copyright, PixController http://www.pixcontroller.com, all rights reserved. This document covers in detail how to modify either the Olympus D-370
More informationHow to Assemble a Desktop PC
How to Assemble a Desktop PC By Taylor Koch iii Table of Contents Introduction to Building a Desktop PC... 1 Preparation and Precautions... 3 PC Parts... 3 Basic Tools... 3 Safety Precautions... 3 Installing
More informationAC300/AC400 SERIES DYNAMIC BRAKING and ADDITIONAL FORM C RELAY. INSTALLATION INSTRUCTIONS Document Number:
Minarik Variable Speed AC Motor Drives AC300/AC400 SERIES DYNAMIC BRAKING and ADDITIONAL FORM C RELAY INSTALLATION INSTRUCTIONS Document Number: 250-0297 These instructions apply to models rated: 7.5 25
More informationAssembly of the TACOS WAT-910BD Housing v2
1) Circuit Diagram 2) Assembly of PCB a)tools Required. Only simple hand tools are necessary to complete the assembly of the PCB. - Soldering Iron and solder - Needle nose pliers - Wire clippers/trimmers
More informationMac Mini Mid 2010 SSD Installation
Mac Mini Mid 2010 SSD Installation Replace your Mac Mini Mid 2010's hard drive for more storage space and an increase in speed. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 15 INTRODUCTION
More informationipad mini 4 LTE Screen and Digitizer Replacement
ipad mini 4 LTE Screen and Digitizer Replacement Replace the fused LCD screen and digitizer in an ipad mini 4 LTE. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Follow
More informationProtoBox 1593Q Kit (PCB+Box)
Protoox 1593Q Kit (PC+ox) Hammond 1593Q handheld plastic enclosure with battery compartment, packaged with a matching PS Protooard 2-hole per strip PC. usoard Prototype Systems - uilt for designers www.usoard.com
More informationipad Mini Wi-Fi Front Facing Camera Replacement
ipad Mini Wi-Fi Front Facing Camera Replacement Replace the Front Facing Camera in your ipad Mini Wi-Fi. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 42 INTRODUCTION
More informationWhen you are ready to build your computer you will have the following materials to work with.
Copyright 2009 BOSMA Enterprises Chapter 3 Putting the Computer Together When you are ready to build your computer you will have the following materials to work with. 1. One motherboard. 2. One ribbon
More informationGPS Series. Build a GPS Smart Logger. By Michael Simpson. As seen in November 2008 of Servo Magazine Pick up an issue at
GPS Series By Michael Simpson Build a GPS Smart Logger As seen in November 2008 of Servo Magazine Pick up an issue at www.servomagazine.com I recently did a GPS series covering various GPS modules and
More informationSNA KIT Assembly Guide
SNA KIT Assembly Guide Ver 0.8 April 2015 Note: Many references still exist to the SNA Kit s predecessor (NAT Kit). Also, the parts and additional steps used to make the NAT an SNA have not yet been shown
More informationWritten By: Sam Lionheart
ipad Mini 2 Wi-Fi LCD Replacement Replace the LCD in an ipad Mini 2 Wi-Fi. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 30 INTRODUCTION Use this guide to open your ipad Mini 2
More informationHow to hardwire the Sony DSC-W35 Digital Camera
How to hardwire the Sony DSC-W35 Digital Camera Copyright, PixController http://www.pixcontroller.com, all rights reserved. Rev. A 3/20/07 This document covers in detail how to modify the Sony DSC-W35
More informationAttaching DX Encoders to your Majestic Carriage
Attaching DX Encoders to your Majestic Carriage Encoders are the white wheels that you need to have on your carriage in order for the stitch regulation to work. Encoders detect the movement of the machine
More informationDMD Extender. Application Note 1 Sega Large Screen LCD Replacement. V0.1 October 2013 Copyright 2013 Dr Pinball
DMD Extender Application Note 1 Sega Large Screen LCD Replacement V0.1 October 2013 Copyright 2013 Dr Pinball Important This document is a guide to installing an LCD panel to replace a plasma display in
More informationPost Tenebras Lab. Written By: Post Tenebras Lab
Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.
More informationInstructions to Install Retrofit Kit 6/7000 Machine
Instructions to Install Retrofit Kit 6/7000 Machine **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit kit contents: PART NAME QUANTITY PART NUMBER
More informationPacific Antenna Two Tone Generator
Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination
More information*on-board power supply capability limited. External battery should be used for higher power servos.
Pan and Tilt Decoder II PART NO. Add affordable Pan and Tilt control to your security cameras using the Pan and Tilt Decoder II and the DFRobot DF05BB Tilt/Pan Kit (5kg), Jameco PN 2144518 or the DAGU
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Chrysler/Dodge/Jeep Remote Add-On CD player for RA1, RA2, RA3, or RA4 radios (Kit # 5000-8750) 2013-current RAM truck and Viper; 2015-current Charger, Challenger, and 300; 2017 Pacifica Please read thoroughly
More informationElecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved
Introduction Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved The connectors furnishing high current to the KPA3 module have failed
More informationGolf Control Panel Conversion Instructions
Golf Control Panel Conversion Instructions Document Part #: 040-0079-01 This document describes the steps for upgrading the control panel on an old golf cabinet for use with an EA SPRTS PGA TUR Golf Conversion
More informationQuicksilver 606 TR-606 CPU Upgrade
Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...
More informationElecraft K3 KREF3 Output Level Modification
Elecraft K3 Revision A, September 15, 2015 Copyright 2015, Elecraft, Inc. All Rights Reserved Introduction This modification increases the output levels from the KREF3 Reference Oscillator to provide proper
More informationFLEXBOX. Installation Guide
FLEXBOX Installation Guide FLEXBOX 1 Important Safety Instructions WEIGHT LIMIT MAXIMUM WEIGHT 50 LBS. THE STRUCTURE TO WHICH THE BOX IS MOUNTED (CEIL- ING, WALL, TABLE, POLE) MUST BE ABLE TO SUPPORT FIVE
More informationProtoBox 1593Q Kit (PCB+Box)
Protoox 1593Q Kit (PC+ox) Hammond 1593Q handheld plastic enclosure with battery compartment, packaged with a matching PS Protooard 2-hole per strip PC. usoard Prototype Systems - uilt for designers www.usoard.com
More informationPortable Qi Charger. Created by Ruiz Brothers. Last updated on :20:38 AM UTC
Portable Qi Charger Created by Ruiz Brothers Last updated on 2017-12-05 01:20:38 AM UTC Guide Contents Guide Contents Overview Prerequisite Guides Parts, Tool & Supplies Universal Qi Wireless Charging
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationXbox 360 Optical Drive Replacement
Xbox 360 Optical Drive Replacement Optical drive replacement. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 21 INTRODUCTION This guide only demonstrates how to remove the optical
More informationA how-to guide for replacing the DJI Phantom 4 body shell. *Replacing the body shell could also be used as a tear-down guide. Written By: GotMac
A how-to guide for replacing the DJI Phantom 4 body shell. *Replacing the body shell could also be used as a tear-down guide. Written By: GotMac ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION
More informationTKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: June 20,
TKEY-1 CW touch key (no electromechanical contacts) Assembly manual Last update: June 20, 2017 ea3gcy@gmail.com Updates and news at: www.ea3gcy.com Thanks for constructing the TKEY-1A CW touch key Have
More informationWritten By: Sam Lionheart
ipad Air Wi-Fi LCD Replacement Use this guide to replace the LCD screen in your ipad Air. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replace a damaged or nonfunctioning
More informationC764i Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
C764i Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 7 Before You Begin... 3 Obtaining Service... 3 Unpacking the Equipment... 3 Important
More information3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions
3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions Version date Author Comments 1.0 29/05/2013 Boris du Reau Initial version Rocket Type Micro-max Model Mid
More informationIQ32 Upgrade Kit Assembly Instructions
IQ32 Upgrade Kit Assembly Instructions Jim Veatch WA2EUJ September 17, 2018 TABLE OF CONTENTS 1. INTRODUCTION... 3 2. IQ-32 UPGRADE KIT INVENTORY... 4 3. PREPARING THE RS-HFIQ AND SIDE PANELS... 6 4. CONNECTING
More informationEQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.
EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationARRIS X-Speed 250B Assembling Manual
ARRIS X-Speed 250B Assembling Manual Thank you for purchasing the ARRIS X-Speed 250B FPV Racing drone. Be sure to read through the entire manual before starting your build. If you bought the ARRIS X-Speed
More informationInstructions for installing your QuiltCam on your Gammill quilt machine.
Instructions for installing your QuiltCam on your Gammill quilt machine. The items include with your QuiltCam Items included in all packages: QuiltCam Control Box, See Figure 1 Power Supply, Figure 2 Video
More informationManual. There is also a growing array of upgrades and customizations, both functional and cosmetic available from quadquestions.
Manual Thank you for purchasing the QQ190 Falcon racing quadcopter and welcome to the QQ190 team. This manual details how to physically assemble the frame. There is a diverse array of electrical components
More informationCP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split. Document revision 2.1 Last modification : 12/11/17
CP5176 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge
More informationUltima X5000 Rectangular Duct Mount Kit User Instructions
Ultima X5000 Rectangular Duct Mount Kit User Instructions MSA Kit 10176947 - Ultima X5000 316 Stainless Steel Parts List / Instructions Rectangular Gasket (1) Rectangular Duct Mount Base Plate (1) Base
More informationipod Classic Headphone Jack & Hold Switch Replacement
ipod Classic Headphone Jack & Hold Switch Replacement Replace Headphone Jack & Hold Switch to fix no audio and/or no unlock Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationTubbutec Sumtiple Kit Version Construction Manual
Tubbutec Sumtiple Kit Version Construction Manual This document describes the construction of the Sumtiple Kit. The following parts are included: 1x Sumtiple PCB with SMD-Parts already soldered 1x Front
More informationWritten By: Andrew Optimus Goldberg
ipad Air LTE SIM Board Replacement Replace the SIM board (a.k.a. SIM card bay) on an ipad Air LTE. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 32 INTRODUCTION Use this
More informationRB-Rld-03. imodela CNC Milling Machine. Overview
RB-Rld-03 imodela CNC Milling Machine Overview imodela is a completely new concept a digital hobby mill designed to support a range of unique creative pursuits, from miniatures and model railroading to
More informationHOW TO REPLACE A PARKER INVERTER DRIVE WITH A YASKAWA V1000 INVERTER DRIVE
HOW TO REPLACE A PARKER INVERTER DRIVE WITH A YASKAWA V1000 INVERTER DRIVE Important: Please read this document in its entirety before removing the Parker VFD drive and installing the Yaskawa V1000 drive.
More informationAlesis MMT8 16x Memory Expansion Modification (Black model MMT8 s) Equipment. Components required. Other bits:
Alesis MMT8 16x Memory Expansion Modification (Black model MMT8 s) by Graham Meredith, 006 Revised 15 th January 009 gmeredith1@yahoo.com.au This modification expands the memory of the Alesis MMT8 to 16x
More informationRedigido por: Sam Lionheart
ipad Mini 2 Wi-Fi Microphone Replacement Replace the dual microphone in the ipad Mini 2 Wi-Fi. Redigido por: Sam Lionheart ifixit CC BY-NC-SA pt.ifixit.com Página 1 de 36 INTRODUÇÃO Use this guide to remove
More informationTIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE
TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE Table of Contents 0. Components List + Tools 0. PCB Sides 03. PCB Assembly 04_. Diode N448 04_. Laying Resistors 04_3. Capacitors 04_4. Quartz 04_5. 78L05
More informationUltima X5000 Round Duct Mount Kit User Instructions
Ultima X5000 Round Duct Mount Kit User Instructions MSA Kit 10179124/10179321 - Ultima X5000 316 Stainless Steel Parts List / Instructions Round Duct Mount Gasket (1) Round Duct Mount Base Plate (1) Base
More informationAsus ZenFone 2 Battery Replacement
If your battery is defective, this replacement guide will allow you to replace your battery. Geschreven door: Eduardo Nodarse ifixit CC BY-NC-SA nl.ifixit.com Pagina 1 van 9 INTRODUCTIE Replacing the battery
More informationLARGE S URGE-PROTECTOR S HELTER
LARGE S URGE-PROTECTOR S HELTER The weather-resistant Large Surge-Protector Shelter (simply referred to as the shelter in this manual) provides protection from the elements for Surge Protectors (not included)
More informationHTC RE Companion Handheld camera
HTC RE Companion Handheld camera disassemby HTC RE Companion camera disassembly starting point. This will get the camera open with minimal damage, and give you some options to repair. Written By: Mike
More informationApex Tablet 7 Battery Replacement
Apex Tablet 7 Battery Replacement This guide will instruct you on how to replace the lithium-ion battery inside the Apex 7" Tablet. Written By: Corrine Nief ifixit CC BY-NC-SA www.ifixit.com Page 1 of
More informationComputer Technician. Technicians Tools. Copyright Texas Education Agency, All rights reserved. 1
Computer Technician Technicians Tools 1 Enabling Objectives Introduction to standard tools Introduction to specialized tools and supplies Introduction to software tools The domestic tools The foreign tools
More informationMailbox Notification Service. Created by Adam Kohring
Mailbox Notification Service Created by Adam Kohring Last updated on 2015-06-24 10:20:07 PM EDT Guide Contents Guide Contents Overview Parts List Adafruit Products Additional Products Print the Circuit
More informationMac Mini Mid 2011 SSD Installation
Mac Mini Mid 2011 SSD Installation Replace your Mac Mini Mid 2011's hard drive for more storage space and an increase in speed. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 14 INTRODUCTION
More informationAssembly Manual. X Bolt FPV Racer Kit AZSZ2903
Assembly Manual X Bolt FPV Racer Kit AZSZ2903 Product specifications are subject to change without notice. Due to ongoing development, the actual product may vary from images shown. This product contains
More informationMotorola Moto X Display Assembly
Motorola Moto X Display Assembly Replacement Replace the display assembly on a Motorola Moto X. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Shattered screen? Darn
More informationInstallation, Usage and Maintenance Guide for Kit 1
Installation, Usage and Maintenance Guide for Kit 1 July 2013 WARNING Read this document before installing or using Data East/Sega Speaker Light Mod by Pinballtoppers Improper installation, improper use,
More informationInstalling a Power over Ethernet injector
Installing a Power over Ethernet injector AlphaEclipse StreetSmart and RoadStar signs The instructions in this document explain how to install/replace a Power over Ethernet (PoE) injector in a StreetSmart
More informationA-100G6 - Basic frame assembly diagram
doepfer System A - 100 Rack system A-100 G A-100G6 - Basic frame assembly diagram Parts: 1 Rail with lip, and with tapped hole strip inserted (with M3 threads). 2 Rail with lip, with three M3 hexagon nuts
More informationProduct Catalog. Esyte Company LLC Indianapolis, IN Phone: Fax:
Product Catalog Esyte Company LLC Indianapolis, IN Phone: 317-809-0828 Fax: 317-807-6116 www.esyte.net Index: Magnetic Products Inspection Mirrors Multi-Tools Pliers Knives Endoscopes Metal Gauge Infrared
More informationCARTRIDGE REMANUFACTURING INSTRUCTIONS
Absolute COLOR Absolute BLACK Unidrums Unirollers Uniparts Unicoatings HP P3005 CARTRIDGE REMANUFACTURING INSTRUCTIONS HP P3005 MONOCHROME LASER PRINTER HP P3005 TONER CARTRIDGE Summit Technologies is
More informationPowerBook G4 Aluminum 17" 1.67 GHz (High- Res) PC Card Cage Replacement
PowerBook G4 Aluminum 17" 1.67 GHz (High- Res) PC Card Cage Replacement Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION Replace a faulty PC card cage to regain functionality
More informationPhi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012
Phi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012 1. Introduction:... 3 Currently available:... 3 2. Backpack assembly... 4 3. Connecting to a keypad... 6 4. Rotary encoder keypads...
More informationModel: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features
Model: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features Fully Adjustable, Multiple Viewing Angle Smart Camera. High Resolution, 1/2 CMOS Color Camera
More informationXbox 360 Motherboard Replacement
Xbox 360 Motherboard Replacement Motherboard replacement. Redigido por: Walter Galan ifixit CC BY-NC-SA pt.ifixit.com Página 1 de 29 INTRODUÇÃO Use this guide to completely strip down your motherboard.
More information