X515ST / W515ST / EH515ST / EH515TST / WU515ST / WU515TST Installation Guide WXGA 1280*800. WUXGA 1920*1200 Brightness. 5000lm

Transcription

1 X515ST W515ST EH515ST EH515TST WU515ST WU515TST Contents Product Description Cabinet Dimensions Installation Notice Lens Spec Image Size & Projection Distance & Diagrams Lens Shift Adjustment Range Back Panel PC Control Codes/ Cable Connections Product Description X515ST W515ST EH515ST/EH515TST WU515ST/WU515TST Resolution XGA 1024*768 WXGA 1280* p 1920*1080 WUXGA 1920*1200 Brightness 6000lm 5500lm 5000lm 5500lm Dimensions Weight Noise 424 x 344 x 120 (w/o feet) 6.1kg 35/32 db Power consumption 445W / 355W (110 VAC) 425W / 340W (220 VAC) BTU/hr 1672 Installation Manual 01

2 Cabinet Dimensions POWER CORD LOCATION IR RECEIVER Air Outlet Air Inlet Lamp door LENS SHIFT KNOB LENS SHIFT KNOB FOCUS RING IR RECEIVER Installation Manual 02

3 Cabinet Dimensions CELING MOUNT SCREW HOLD 3-M4x7 mm ADJUSTABLE FEET EYE BOLT SCREW HOLE 2-M8x15 mm Lens Spec X515ST W515ST EH515ST/EH515TST WU515ST/WU515TST Throw ratio F# / Focal Length F/2.5; f=11.66mm Zoom/Focus Manual focus, fixed zoon Screen size 30~300 inches 27.97~302 inches 28.59~303 inches 29.38~305.6 inches Offset angle 95% ~105% 105%~125% 105% ~130% 100% ~120% Throw Distance 0.5~5M 0.5~5.4M 0.5~5.3M 0.5~5.2M Installation Manual 03

4 SETUP AND INSTALLATION Projector installation notice Place the projector in a horizontal position. The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically, and may lead to other unpredictable damages Allow at least 50 cm clearance around the exhaust vent. Minimum 500mm (19.69 inches) Minimum 500mm (19.69 inches) Minimum 500mm (19.69 inches) Minimum 100mm (3.94 inches) Minimum 500mm (19.69 inches) Minimum 300mm (11.81 inches) Ensure that the intake vents do not recycle hot air from the exhaust vent. When operating the projector in an enclosed space, ensure that the surrounding air temperature within the enclosure does not exceed operation temperature while the projector is running, and the air intake and exhaust vents are unobstructed. All enclosures should pass a certified thermal evaluation to ensure that the projector does not recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the acceptable operation temperature range. Installation Manual 04

5 Image Size & Projection Distance & Diagrams (WUXGA) Desired Image Size Projection Distance (C) Diagonal Width Height Wide m inch m inch m inch m feet Lens Shift Range PJ lens Center to top of image Vertical + Vertical - (Max) (A) (Min) (B) at the center of shif (D) = (A) - (B) at 1% position Image Shift Range +(Right) (Left) (1080P) Desired Image Size Diagonal Width Height Projection Distance (C) m inch m inch m inch m feet Lens Shift Range PJ lens Center to top of image Vertical + Vertical - (Max) (A) (Min) (B) at the center of shif (D) = (A) - (B) at 1% position Image Shift Range +(Right) (Left) Note Vertical Lens Shift values are always calculated from the Center of Projection Lens. Therefore the distance 5.2 cm (2.05 inch) from the Base to the Center of Projection Lens needs to be added to each Vertical Lens Shift value. Installation Manual 05

6 Image Size & Projection Distance & Diagrams (WXGA) Desired Image Size Projection Distance (C) Diagonal Width Height Wide m inch m inch m inch m feet Lens Shift Range PJ lens Center to top of image Vertical + Vertical - (Max) (A) (Min) (B) at the center of shif (D) = (A) - (B) at 1% position Image Shift Range +(Right) (Left) (XGA) Desired Image Size Projection Distance (C) Diagonal Width Height Wide m inch m inch m inch m feet Lens Shift Range PJ lens Center to top of image Vertical + Vertical - (Max) (A) (Min) (B) at the center of shif (D) = (A) - (B) at 1% position Image Shift Range +(Right) (Left) Note Vertical Lens Shift values are always calculated from the Center of Projection Lens. Therefore the distance 5.2 cm (2.05 inch) from the Base to the Center of Projection Lens needs to be added to each Vertical Lens Shift value. Installation Manual 06

7 Lens Shift Diagrams H Wall 1. Center of projection lens. 2. Projection image while lens shift at the highest position. 3. shift range: 10% H. 4. Vertical shift range: 20% V V A B V+ V V+ V cm Base C Back Panel EH515TST / WU515TST MOUSE HDMI 1 / MHL HDMI 2 DisplayPort VGA1-IN / YPbPr VGA-OUT S-VIDEO L AUDIO1-IN (VGA1) AUDIO OUT 3D SYNC Out (5V) SERVICE LAN USB Power Out (1.5A) 12V OUT R HDBaseT VGA2-IN / YPbPr / RS-232C VIDEO AUDIO2-IN AUDIO3-IN (VGA2) (VIDEO/S-VIDEO) WIRED REMOTE X515ST / W515ST / EH515ST / WU515ST MOUSE HDMI 1 / MHL HDMI 2 DisplayPort VGA1-IN / YPbPr VGA-OUT S-VIDEO L AUDIO1-IN (VGA1) AUDIO OUT 3D SYNC Out (5V) SERVICE LAN USB Power Out (1.5A) 12V OUT R VGA2-IN / YPbPr / RS-232C VIDEO AUDIO2-IN AUDIO3-IN (VGA2) (VIDEO/S-VIDEO) WIRED REMOTE 1. Enter 2. Keystone Correction 3. Power 4. Information 5. Menu 6. Re-Sync 7. Source 8. Four 9. Directional Select Keys 10. Temp LED 11. Lamp LED 12. On/Standby LED Installation Manual 07

8 PC Control Codes RS232 protocol function list Baud Rate : 9600 Data Bits: 8 ASCII code Parity: None Stop Bits: 1 Flow Control : None UART16550 FIFO: Disable Projector Return (Pass): P Projector Return (Fail): F XX=01-99, projector's ID, XX=00 is for all projectors Note: There is a <CR> after all ASCII commands 0D is the HEX code for <CR> in ASCII code. SEND to projector 232 ASCII HEX Code Function Description Code ~XX00 1 7E D Power ON ~XX00 0 7E D Power OFF (0/2 for backward compatible) ~XX03 1 7E D Mute On ~XX03 2 7E D Off (0/2 for backward compatible) ~XX12 1 7E D Direct Source Commands HDMI1 ~XX E D HDMI2 ~XX E D Displayport ~XX12 5 7E D VGA1 ~XX12 8 7E D VGA1 Component ~XX12 6 7E D VGA 2 ~XX E D VGA2 Component ~XX12 9 7E D S-Video ~XX E D Video ~XX E D HDBaseT (only exists in "T" SKU) ~XX20 1 7E D Display Mode Presentation ~XX20 2 7E D Bright ~XX20 3 7E D Movie ~XX20 4 7E D srgb ~XX20 5 7E D User ~XX20 7 7E D Blackboard ~XX E D DICOM SIM. ~XX20 9 7E D SEND from projector automatically 232 ASCII Code HEX Code Function Projector Return Description when Standby/Warming/Cooling/Out of Range/Lamp fail/fan Lock/Over Temperature/ Lamp Hours Running Out/ Cover Open INFOn n=0 Standby n=1 Warming n=2 Cooling n=3 Out of Range n=4 Lamp fail n=6 Fan Lock/ n=7 Over Temperature n=8 Lamp Hours Running Out RS232 commands by TELNET Telnet Port : 23 Installation Manual 08