NOTE: Attaches to Centro Trac, Retrac, Duplex Cable and Monopoint Systems. Evo Gobo/Framing Projector available but not shown.

Size: px

Start display at page:

Download "NOTE: Attaches to Centro Trac, Retrac, Duplex Cable and Monopoint Systems. Evo Gobo/Framing Projector available but not shown."

Irma Terry
5 years ago
Views:

Safety Instructions 1. CAUTION: Read all instructions. Do not install any Spotlight closer than six inches from any curtain or similar combustible material.

Ensure the Spotlight connector is attached correctly to the system with no cross threading and is tightened down completely to make contact with the top of the track. Ensure all connections are tight.

Use only as described in these Tegan Lighting. Use only Tegan Lighting supplied accessories. Luminaires may be extremely hot, allow to cool before touching.

1 Safety Instructions 1. CAUTION: Read all instructions. Do not install any Spotlight closer than six inches from any curtain or similar combustible material. Do not install this system in a damp or wet location. Turn off electrical power before modifying the lighting system in any way. Ensure the Spotlight connector is attached correctly to the system with no cross threading and is tightened down completely to make contact with the top of the track. Ensure all connections are tight. Bad connections can cause overheating, arcing and a potential fire risk. Always use appropriate Spotlight with 50W 10 MR-16 Halogen or equal MR-16 LED recommended for Evo; 12 LED optic for Oculus. Use only as described in these Tegan Lighting. Use only Tegan Lighting supplied accessories. Luminaires may be extremely hot, allow to cool before touching. These are for 12VAC or 24VDC Spotlights; they must be connected to an appropriate 12VAC or 24VDC power supply. Refer to Specification Sheets. For proper installation, have a qualified electrician install this product. This luminaire must be wired and grounded in accordance standard accepted electrical installation practices, local codes, and ordinances. Wire supply connections must be made with U.L. or comparible testing agency-approved connectors. Regular cleaning of these products is important. Switch off at main supply and allow to cool before touching. Clean fittings with a soft damp cloth and allow to dry before reconnecting power supply. Evo-LP Halogen Gobo/Framing Projector (E-LP-GFP) Oculus LED Gobo/Framing Projector (OGFP) Gobo/Framing Projector Overview NOTE: Attaches to Centro Trac, Retrac, Duplex Cable and Monopoint Systems. Evo Gobo/Framing Projector available but not shown. teganlighting.com info@teganlighting.com TG-INS-GFP 1

2 A T B D Spotlight Cocnstucion R Q S C E F P O N M L K J I H G Main main Body body Lamp lamp Housing housing Lens lens Housing housing Media accessory Holder holder (sold separately) (sold ) seperate A. Twist & Click Connector B. 2mm Allen Key C. Safety Cable D. Framing Arm E. Shutter F. Focusing Wheel G. Evo Media Holder 2-16 (EMH2-16) H. Lens I. Accessory Clip J. Focusing Lens K. Gobo Retaining Screws L. Release Knob M. Gobo Rotator N. Source (Evo, Evo-LP: 50W MR ; LED MR-16 or equal; Oculus: 10W LED- 12 ) O. Safety Cable Screw P. Alignment Guide Q. Angle Gauge R. Vertical Lock (Evo LP) S. Horizontal Lock (Evo LP) T. Twist & Lock Collar 1. Lamp Replacement HOT HOT ALIGN Evo & Evo-LP (shown) 1. Changing the MR-16 lamp. CAUTION lamp and lamp housing may be extremely hot. Allow to cool before touching. Twist Gobo/Framing Projector counterclockwise and remove. Install lamp, ensuring it is connected securely. To reattach Gobo/Framing Projector, align indicator as shown and twist clockwise until you hear a click. Lamp types: Evo, Evo-LP: 50W MR ; LED MR-16 or equal; Oculus: 10W LED-12 teganlighting.com info@teganlighting.com TG-INS-GFP 2

3 Media Installation Detail of Media Holder Assembly CLICK Evo-LP Body (E-LP) Gobo/Framing Projector (E-LP-GFP Media Evo Media Holder 2-16 (EMH2-16) Media Clip Front of Projector Evo Media Holder 2-16 with Media 2. Safety Cable Installation Attach safety cable (if fitted) Remove Gobo/Framing Projector as indicated in section 1. Attach cable using leash screw on main body. Replace Gobo/Framing Projector as directed in section 1. NOTE: Ensure safety leash is contained within lamp housing before reattaching to base. 3. Media Installation Install up to two accessories into Evo, Evo-LP or Oculus Media Holder. Secure media in place using retaining clip. Insert media holder into housing until it clicks into place. Lock luminaire position using 2mm allen key provided. NOTE: Only adjust spotlight position when unlocked. NOTE: Refer to Installation Sheets # s 07, 08 and 09 for additional details on installing Evo, Evo-LP and Oculus Spotlights. 3. E Size E SIZE Gobo GOBO Gobo Installation Artwork ARTWORK 22mm 11/16 OVERALL (22mm) SIZE 37.5mm Overall Size 1 1/2 (37mm) ROTATE 3. Gobo Installation To remove lens housing, slide release knob back and twist lens housing counterclockwise. Secure Gobo in place using retaining screws and reattach lens housing. To rotate pattern, rotate lens housing to desired position. NOTE: The Framing arm should be removed to maintin the aesthetic of the product. teganlighting.com info@teganlighting.com TG-INS-GFP 3

4 4. Framing Patterns 4 Framing Patterns Connect the framing arm to the shutter plate as indicated. Use the framing arm to position each shutter plate individually. NOTE: The framing arm should be removed to maintain the aesthetic of the product. 5. Beam Adjustment REAR LENS FRONT LENS FORWARD BACKWARD FORWARD BACKWARD 5. Focusing and Resizing the Beam The lens housing contains two lenses used to focus and resize the beam. These lenses can be moved forward and backward using the two focusing wheels. teganlighting.com info@teganlighting.com TG-INS-GFP 4

5 AME SIZES FRAME SIZES maximum frame size minimum frame size DISTANCE (m/ft) FRAME SIZE (W x H) PEAK LUX/ AVERAGE LUX/ FOOTCANDLES FOOTCANDLES FRAME SIZE (lx/fc) (lx/fc) (W x H) DISTANCE (m/ft) 1.0 m/ m/1-8 x 0.52m/ lx/154.2 fc 1410 lx/140 fc 0.38m/1-3 x 0.38m/ m/ m/ m/2-6 x 0.77m/ lx/76.2 fc 680 lx/63.2 fc 0.55m/1-9 x 0.55m/ m/4-11 Frame Sizes & Angles 2.0 m/ m/ m/ m/3-4 x1.02m/ m/5 x 1.53m/5 2.05m/6-9 x 2.05m/ lx/41.8 fc 205 lx/19 fc 110 lx/10.2 fc 390 lx/36.2 fc 180 lx/16.7 fc 90 lx/8.4 fc 0.74m/2-5 x 0.74m/ m/3-7 x 1.10m/ m/4-9 x 1.45m/ m/ m/ m/ m/ lx/7.4 fc 58 lx/5.4 fc 5.0 m/ m/8-6 x 2.60m/8-6 Frame frame sizes based ase n on projecting r e in s uare square n on. 1.85m/6-1 x 1.85m/6-1 AMING ANGLES FRAMING ANGLES s uare Square On n Above a e e Below Left ef ri Right m ina i n Combination 5. Operating the Evo/Oculus Gobo/Framing Projector The table states the minimum and maximum frame sizes possible at set distances. These sizes are achieved by moving the front and rear lenses. Maximum Position rear lens at midpoint of lens housing. Move front lens back to center and adjust to focus. Minimum Extend both lenses to their front and rear limits. Adjust rear lens to focus beam. NOTE: Shutter plates can be used to increase or decrease the size of the frame depending on project requirements. teganlighting.com info@teganlighting.com TG-INS-GFP 5

BPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

BPL SERIES INSTALLATION INSTRUCTIONS Important Warning THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This product must be installed in accordance with National Electrical