Concealed hinges. Concealed hinges. Function and design for perfecting motion. blum.com blum.com

Transcription

1 Concealed hinges Concealed hinges Function and design for perfecting motion blum.com blum.com

2 Quick reference inge cup centerpoint 9.5 door Ø35 C mm Conversion chart inch 1 1 / C = cup centerpoint /16" 27/32" 7/8" 15/16" 31/32" 1" = bore distance inges per door cabinet height 100" 80" 60" 40" 20" 45 hinges required per door <15 lb Ø lb his chart can serve as a guide for determining the number of hinges per door. Note that door weight can also determine the number of hinges required. NOE: he distance between the top and bottom hinges must be greater than the width of the door inge abbreviation key W lb S lb / / / / / / / / / / / / / / / / / / / R OL = oring distance = Plate height OL = Door overlay P = Door protrusion R = Reveal S = Side arm protrusion = Door thickness W = Side panel width FD = Fixed distance Fixed distance (FD) P / / / / / / / / / / / he distance that the cup overlays the cabinet side panel when a hinge is attached to a 0 mm mounting plate. his is used to calculate hinge overlay with the formula X + minus = OL (Fixed distance + boring distance minus plate height = overlay)

3 Elegant design and superior function lum hinges are designed to address the needs of today s kitchen. lum hinges offer solutions for virtually any application. In combination with LUMOION soft close, doors close silently and effortlessly. Contents 5 esting standards 6 CLIP top and CLIP hinges overview CLIP top hinges 34 CLIP top angled hinges 46 CLIP hinges 48 CLIP mounting plates 52 LUMOION for doors CLIP top/clip 62 IP-ON for doors 68 COMPAC hinges 77 LUMOION for doors COMPAC 78 inge accessories 80 Assembly aids 88 Part number index

4 eautiful hinges inside CLIP top and CLIP hinge series inges for special applications COMPAC hinges

5 and out

6 inges built to last Perfecting motion for cabinet doors he comprehensive lum hinge program has the right solution for every application. All products are designed to be of the highest quality and function, durable and easy to assemble. With a discreet design, lum hinges prove that even the inside of cabinets can be attractive and eye catching. Assembly lum hinges are characterized by their easy installation. oth CLIP top and CLIP are equipped with the proven CLIP technology enabling tool-free attachment and removal of doors lum, Inc. Subject to technical modifications without notice

7 esting standards All lum hinges meet or exceed ANSI/MA A grade 2 requirements. All concealed hinges are designed for indoor use. Cycle test Without load 200,000 opening and closing cycles for Euro hinges 100,000 opening and closing for CLIP mini and all COMPAC hinges With load 11 lb extra weight is applied for 100,000 opening and closing cycles kg Load test Static load 67 lb applied ten times for five seconds, each at 45 opening angle Dynamic load 44 lb extra weight applied for fifty opening and closing cycles kg Over push test Without load Euro hinges Increasing forces up to 33 lb applied for a total of forty times for five seconds each COMPAC hinges Increasing forces up to 11 lb applied for a total of five times for five seconds each > General information All lum hardware undergoes strict quality control procedures through all stages of production. lum hardware is designed for cabinets and cabinet components made from wood, melamine or MDF. Careful attention must be paid to installation and operating instructions when using lum hardware (see catalogs and instruction sheets for all technical information). he manufacturer must decide on the screws or attachment methods to suit the material being used (i.e. wood, melamine, etc.). he hardware must not be exposed to acidic or corrosive materials (i.e. some household cleaning solutions). o ensure that lum hardware functions correctly, it must be kept clean and undamaged. For any additional information please contact your lum representative. Anyone selling lum hardware must ensure that their customer is aware of any relevant information given in this catalog. Conditions of sale and delivery All deliveries and services are based on the general conditions of sale which are available upon request. he technical presentations and dimensions in illustrations are non-binding. We reserve the right to make changes to specifications at any time. We do not accept any responsibility for any errors which may occur in the production of this catalog. Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 5

8 6 20 lum, Inc.

9 CLIP top and CLIP hinges Euro hinges for every application CLIP top lum s premium Euro hinge with exclusive Spiral ech depth adjustment CLIP he industry standard for tool-free attachment since 85 Audible CLIP sound confirms the secure connection between hinge and plate Available with INSERA tool-free attachment and removal Mounting plates for face frame and panel cabinets hree-dimensional adjustments for precise door alignment Complete angled hinge program Special hinges available for thick, aluminum and glass doors Nickel-plated steel construction IP-ON for doors is also available Add-on LUMOION soft close available CLIP top LUMOION with integrated soft close is also available > inge planning tools lum has downloadable Excel spreadsheets that help determine the hinge that is right for your application. Planning tools are easily accessible on our website at blum.com/planning Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 7

10 CLIP top and CLIP hinges INSERA tool-free assembly lum offers tool-free attachment of hinge to door and plate to cabinet with INSERA hinges and mounting plates ime proven CLIP technology For 25 years, CLIP hinges have been preferred, throughout the world, by companies whose reputations rely on dependable door function lum, Inc. Subject to technical modifications without notice

11 lum three-point contact CLIP top and CLIP hinges have three-point contact between the hinge and mounting plate to keep them firmly connected under heavy usage. Side adjustment lum s side adjustment is a flush screw head that allows 4 mm of adjustment. It also has an integral stop that prevents removal. Spiral ech depth adjustment With lum s Spiral ech depth adjustment just one and three quarter revolutions of the screw creates 5 mm of adjustment without loosening and retightening a fixing screw. Wide variety of mounting plates lum has mounting plates for every application from wing plates with pre-attached screws or dowels and cam height adjustable face frame adapters to sleek in-line mounting plates. Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 9

12 Program overview Euro hinges CLIP top hinges Applications 107 hinge 110 hinge 120 hinge 170 hinge 107 opening angle page 110 opening angle Standard applications page 14 Special applications page opening angle Standard applications page 16 Special applications page opening angle Standard applications page 18 Special applications page 95 hick door hinge 95 opening angle page zero protrusion hinge 155 opening angle Standard applications page 21 Special applications page 22 Aluminum door hinge lind corner hinge Diagonal 45 hinge Mini hinge Glass door hinge i-fold hinge Angled hinges CLIP hinges 120 opening angle 95 opening angle 110 opening angle 95 opening angle 95 opening angle 60 opening angle Angled hinges from +45 to -45 Applications page 24 page 26 page 28 page 29 page 30 page 31 page hinge 107 hinge 100 opening angle 107 opening angle page 32 page 33 CLIP mounting plates page 48 LUMOION for doors page 52 Accessories pages 34-35, lum, Inc. Subject to technical modifications without notice

13 Using this section lum's concealed hinges brochure makes it easy to use our Euro hinges. Each page shows information for both face frame and panel applications. he top row shows the hinge in a face frame cabinet and the center row shows it in a panel cabinet. he bottom holds the overlay/reveal tables and hinge part numbers. Minimum reveal o determine the minimum reveal, use the table in the upper right hand corner of each page. Features hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 26 (1") 86 angle restriction clip available (703553) All metal hinge, nickel plated Minimum reveal table = boring = door thickness distance For thickness greater than 26 trial app. recommended Face frame construction o use Euro hinges in a face frame cabinet, use the top row. Panel construction o use Euro hinges in a panel cabinet, use the center row. Overlay Frame Panel * 66.5 W overlay Partial/twin overlay Frame Panel * 66.5 W overlay Inset Frame 68 * = 9 NOE: Application requires a half-cranked hinge and mounting plate Panel = 0 14 min. reveal Overlay and reveal tables o determine the overlay and reveals, use the tables at the bottom of each column. Select hinge Select the appropriate hinge from the bottom of each column. Screw-on, press-in, EXPANDO and INSERA are available for most hinges * overlay *All 35 mm and 8 mm holes must be a minimum of mm deep Overlay P S Overlay P S fixed distance boring distance = = fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in frame cabinets, 9 plate is only for panel cabinets Reveal W P S * reveal = boring distance * Reveal P S fixed distance: 0 = -7 = boring distance 9 = 1.5 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width reveal Straight-arm Self close Free swing Screw-on L Press-in L INSERA L EXPANDO 71358E alf-cranked Self close Free swing Screw-on L Press-in INSERA L Full-cranked Self close Free swing Screw-on L Press-in 7180 INSERA 7190 Step-by-step the following example is based on a panel cabinet with an overlay Step 1 Determine cabinet construction Face frame Panel Step 2 Determine the overlay or reveal Overlay Partial/twin overlay Inset overlay reveal reveal Step 3 Find boring distance and mounting plate height ased on your overlay use the Overlay P S table to determine the mounting plate height and boring distance needed = = 6 overlay = fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Step 4 Check minimum reveal table All minimum reveal tables are Minimum reveal table based on square edge door with a 1 mm radius. A larger radius or profile door will change the minimum reveal required = rad (1/32 ") boring distance rial application = recommended door thickness minimum reveal Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 11

14 General specifications inge-to-door attachment Screw-on Use #6 wood screws Press-in Pre-attached Ø8 mm dowels installed with lum knock-in tool or MINIPRESS with an insertion ram EXPANDO Pre-attached Ø8 mm expanding dowels INSERA ool-free attachment (cup expands into Ø35 mm hole) CLIP top 110 hinges (lever expands into Ø8 mm holes) Screw-on EXPANDO Pre-attached expanding Ø5 mm dowels INSERA ool-free attachment with INSERA expanding Ø5 mm dowels hree-dimensional adjustment Side adjustment Rotate front screw to increase or decrease door overlay ± 2 mm. eight adjustment Rotate cam screw on mounting plate to adjust door position (± 2 mm). On non-cam mounting plates, loosen screws, adjust door and retighten screws. Depth adjustment Rotate rear Spiral ech cam screw to adjust door position (+3 mm, -2 mm). For CLIP hinges, loosen rear screws, adjust door and retighten screws lum, Inc. Subject to technical modifications without notice

15 CLIP top 107 hinges 107 Features hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 22 (7/8") 86 angle restriction clip available ( ) All metal hinge, nickel-plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness For thickness greater than 22 trial app. recommended CLIP top Overlay Frame overlay Panel W overlay Overlay P S fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Straight-arm Screw-on Press-in INSERA 40 Self close Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc.

16 CLIP top 110 hinges 110 Features hree-dimensional adjustment Available with INSERA attachment INSERA lever expands in Ø8 mm holes For door thicknesses up to 26 (1") 86 angle restriction clip available (703553) All metal hinge, nickel plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness For thickness greater than 26 trial app. recommended Overlay Frame Partial/twin overlay Frame Inset Frame = 9 Panel * 66.5 W overlay Panel 66.5 * W overlay NOE: Application requires a half-cranked hinge and mounting plate Panel 68 * = 0 14 min. reveal 66.5 * overlay * reveal * reveal *All 35 mm and 8 mm holes must be a minimum of mm deep Overlay P S Overlay P S fixed distance = boring distance = fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in frame cabinets, 9 plate is only for panel cabinets Reveal W P S = boring distance Reveal P S fixed distance: 0 = -7 = boring distance 9 = 1.5 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width Straight-arm Self close Free swing Screw-on L Press-in L INSERA L EXPANDO 71358E alf-cranked Self close Free swing Screw-on L Press-in INSERA L Full-cranked Self close Free swing Screw-on L Press-in 7180 INSERA lum, Inc. Subject to technical modifications without notice

17 CLIP top hinges 110 Features For larger overlays (22 mm maximum) hree-dimensional adjustment Available with INSERA attachment INSERA lever expands in Ø8 mm holes For door thicknesses up to 26 (1") 86 angle restriction clip available (703553) All metal hinge, nickel plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness CLIP top For thickness greater than 26 trial app. recommended Overlay Partial/twin overlay uilding both frame and panel cabinets Frame Panel W Frame * overlay * 66.5 overlay hinge (7335XX) plate ( ) 4.5 (1/2") same boring distance Panel W Panel W Panel * overlay *All 35 mm and 8 mm holes must be a minimum of mm deep Overlay P S Overlay P S fixed distance = boring distance = Reveal W P S fixed 2 16 distance = boring distance = NOE: 4.5 plate is only for use in frame cabinets, 9 plate is only for panel cabinets = boring distance * 66.5 reveal hinge (7335XX) plate (any 0 mm plate) he most common overlays for frame and panel cabinets can be achieved by using the same machine setting for hinge cup boring. ore all doors at 4.5 mm to achieve: (1/2") overlay on frame cabinets 17.5 (11/16") overlay on panel cabinets Advantages: (11/16") One machine setting fro boring all doors Same hinge used for both applications Straight-arm Self close Free swing Screw-on L Press-in L INSERA L EXPANDO 73358E Straight-arm Self close Free swing Screw-on L Press-in L INSERA L EXPANDO 73358E Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 15

18 CLIP top 120 hinges 120 Features hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 22 (7/8") All metal hinge, nickel-plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness For thickness greater than 22 trial app. recommended Overlay Partial/twin overlay Inset Frame Frame Frame overlay overlay min. reveal Panel W Panel W NOE: his application uses a half-cranked hinge and mounting plate Panel W overlay reveal reveal Overlay P S fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Overlay P S fixed distance = boring distance = 1.5 Reveal W P S = boring distance Reveal P S fixed distance = boring distance = -7.5 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width Straight-arm Self close alf-cranked Self close alf-cranked Self close Screw-on Screw-on Screw-on Press-in Press-in Press-in INSERA INSERA INSERA EXPANDO 71558E lum, Inc. Subject to technical modifications without notice

19 CLIP top hinges 120 Features For larger overlays (21 mm maximum) hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 22 (7/8") All metal hinge, nickel-plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness For thickness greater than 22 trial app. recommended CLIP top Overlay Partial/twin overlay uilding both frame and panel cabinets Frame Panel W Frame overlay overlay hinge (7355XX) plate ( ) 4.5 (1/2") same boring distance Panel W Panel W Panel overlay reveal hinge (7355XX) plate (any 0 mm plate) (11/16") Overlay P S fixed distance = boring distance = NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Overlay P S fixed distance = boring distance = Reveal W P S = boring distance he most common overlays for frame and panel cabinets can be achieved by using the same machine setting for hinge cup boring. ore all doors at 4.5 mm to achieve: (1/2") overlay on frame cabinets 17.5 (11/16") overlay on panel cabinets Advantages: One machine setting for boring all doors Same hinge used for both applications Straight-arm Self close Straight-arm Self close Abbreviations Screw-on Screw-on = Plate height Press-in Press-in P = Door protrusion INSERA INSERA S = Side arm protrusion EXPANDO 73558E EXPANDO 73558E W = Side panel width Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 17

20 CLIP top 170 hinges Features hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 24 (15/16") 0 angle restriction clip available ( ) All metal hinge, nickel-plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness For thickness greater than 24 trial app. recommended Overlay Partial/twin overlay Inset Frame Frame Inset application not possible with 170 hinges and the inset face frame adapter ( ) overlay NOE: 1756xxx or 175L recommended 11 Panel W Panel Panel overlay W overlay reveal reveal Overlay P S fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Overlay P S fixed distance = boring distance = 1.5 Reveal W P S = boring distance Reveal P S fixed distance = boring distance = -7.5 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width Straight-arm Self close Free swing Screw-on Press-in INSERA L alf-cranked Self close Free swing Screw-on L Press-in INSERA alf-cranked Self close Free swing Screw-on L Press-in INSERA lum, Inc. Subject to technical modifications without notice

21 Special applications 170 Straight-arm applications hick door application = 0 hick door twin application = 0 max. protrusion 65 CLIP top straight-arm hing e angle restriction clip straight-arm hing e angle restriction clip Z = 5 = min. reveal 0 0 rial application recommended rial application recommended Z = gap = door thickness Minimum reveal table = door thickness alf-cranked applications Lip door application Mitered corner door application = 3 max. protrusion 74 = 3 max. protrusion half-cranked hinge angle restriction clip half-cranked hinge = lip detail rial application recommended rial application recommended NOE: he above applications can be achieved in face frame cabinets by blocking out behind the frame Angle restriction clip LUMOION for 170 hinges Reduces opening angle of the CLIP top 170 to 0 Installs quickly, easily and tool-free lack nylon Angle restriction clip X lumotion for 170 hinge S inge X S CLIP top 170 straight-arm CLIP top 170 half-cranked A6000 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc.

22 CLIP top 95 thick door hinges 95 Features hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 30 (1-3/16") All metal hinge, nickel-plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness For thickness greater than 30 trial app. recommended Overlay Partial/twin overlay Inset Frame Frame Frame = 9 Panel * 66 W overlay Panel * 66 W overlay NOE: Use a half-cranked hinge and mounting plate for this application Panel 67.5 * = 0 14 min. reveal 66 * overlay * 66 reveal 67.5 * reveal *All 35 mm and 8 mm holes must be a minimum of mm deep Overlay P S fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in frame cabinets, 9 plate is only for panel cabinets Overlay P S fixed distance = boring distance = 1.5 Reveal W P S = boring distance Reveal P S fixed distance: 0 = -7 = boring distance 9 = 1.5 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width Straight-arm Self close Free swing Screw-on L Press-in L INSERA alf-cranked Self close Free swing Screw-on L Press-in INSERA Full-cranked Self close Free swing Screw-on L Press-in INSERA lum, Inc. Subject to technical modifications without notice

23 CLIP top 155 zero protrusion hinges 155 Features For use in cabinets with interior roll-outs hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 24 (15/16") Angle restriction clips available All metal hinge, nickel-plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness For thickness greater than 24, please see page 27 CLIP top Overlay Frame Door protrusion At 90 opening, using 0 mm plate, the door will have -2.3 mm protrusion regardless of boring distance. Use side adjustment to increase or decrease door protrusion overlay NOE: Use of 0 mm or 3 mm is recommended for zero protrusion LUMOION for 155 hinges Panel W S X inge X S 72.5 CLIP top 155 straight-arm CLIP top 155 half-cranked LUMOION for 155 hinge 973A overlay inge cup dimensions 57 Overlay P S fixed distance = boring distance = 11 Straight-arm Screw-on Press-in INSERA Self close N N N01 Angle restriction clips / *47 *INSERA For use with 155 hinges only Gray nylon 110 restriction clip N 92 restriction clip N Abbreviations = Plate height P = Door protrusion S = Side arm protrusion = Door thickness W = Side panel width Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 21

24 20 CLIP top 155 straight-arm special applications 155 Maximum door thickness Maximum door overlay = 0 = 0 34 max N N reveal = 23 max rial application recommended NOE: For thick door applications, you must bore at the specified boring distance listed in the chart below rial application recommended Minimum reveal = door thickness = boring distance *Minimum reveal is 1 mm on a 25 mm thick door when bored at 8 mm Mitered door with large overlay Overlay = boring distance hin facing added to door = 0 = N N max 11.7 = = rial application recommended rial application recommended NOE: hese applications can be achieved in face frame cabinets by blocking out behind the frame Straight-arm Self close Angle restriction clips Abbreviations Screw-on N For use with 155 hinges only = Plate height Press-in N Gray nylon P = Door protrusion INSERA N01 S = Side arm protrusion 110 restriction clip N = Door thickness 92 restriction clip N09 W = Side panel width lum, Inc. Subject to technical modifications without notice

25 CLIP top 155 half-cranked special applications 155 Lip door hick lip door = 3 = 6 CLIP top N max = lip detail max = 3 lip detail 10 P = overlay rial application recommended rial application recommended wo-sided and four-sided mitered door LUMOION for 155 hinges = X S = inge X S CLIP top 155 straight-arm P = 7.2 CLIP top 155 half-cranked rial application recommended LUMOION for 155 hinge NOE: hese applications can be achieved in face frame cabinets by blocking out behind the frame 973A7000 alf-cranked Self close Angle restriction clips Abbreviations Screw-on N For use with 155 hinges only = Plate height INSERA N01 Gray nylon P = Door protrusion 110 restriction clip N S = Side arm protrusion 92 restriction clip N09 W = Side panel width Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 23

26 CLIP top 120 aluminum door hinges for LUMOION 120 Features For use with LUMOION 973A hree-dimensional adjustment For door thicknesses up to 22 (7/8") All metal hinge, nickel-plated Minimum reveal table door frame width = door thickness For thickness greater than 22 trial app. recommended Overlay Frame Specifications Ø7 R 4 overlay door frame width 6 17 Panel R 4 W Insert hinges into machined openings Attach with special screws provided with hinges ( ) door frame width overlay Overlay P S fixed boring distance NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Abbreviations = Plate height P = Door protrusion Straight-arm Screw-on Self close 73550A S = Side arm protrusion W = Side panel width lum, Inc. Subject to technical modifications without notice

27 CLIP top 120 aluminum door hinges 120 Features Not for use with LUMOION 973A hree-dimensional adjustment For door thicknesses up to 22 (7/8") All metal hinge, nickel-plated Minimum reveal table door frame width = door thickness For thickness greater than 22 trial app. recommended CLIP top Overlay Frame Specifications R 4 door frame width overlay 6 17 Panel R 4 W Insert hinges into machined openings Attach with special screws provided with hinges ( ) 90 Ø7 door frame width overlay Overlay P S fixed boring distance NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Straight-arm Self close Free swing Screw-on 73550A 72550A.L Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 25

28 CLIP top 95 inset blind corner hinge 95 Features hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 24 (15/16") All metal hinge, nickel-plated Minimum reveal table = boring distance = door thickness For thickness greater than 24 trial app. recommended Flush door applications Offset door applications Adjustments and clearances overlay adjust gap adjust reveal reveal ±2 gap ±2.5 overlay ack of door is flush with stationary panel Stationary panel spaced out thickness of door bumper Stationary panel mounted to cabinet side, top and bottom min min. S 1.5 reveal 3 reveal P Reveal P S = boring distance Reveal P S = boring distance Inset blind corner Self close Inset blind corner Self close Abbreviations Screw-on Screw-on = Plate height Press-in Press-in P = Door protrusion INSERA INSERA S = Side arm protrusion lum, Inc. Subject to technical modifications without notice

29 CLIP top 95 overlay blind corner hinge 95 Features hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 24 (15/16") All metal hinge, nickel-plated Minimum reveal table = boring distance = door thickness For thickness greater than 24 trial app. recommended CLIP top Overlay application Adjustments and clearances overlay adjust gap adjust overlay 86 minimum setback D FP gap S ±2 gap ±2.5 overlay stationary panel overlay P FP NOE: Door gap can be adjusted ± 2 mm Setback Overlay P D fixed distance = boring distance = 9 NOE: Door overlay varies depending on the setback position of the mounting plate. Use the table to select the desired overlay and cross-reference to the plate setback and bore distance. Overlay blind corner INSERA Self close Gap S FP = front panel thickness NOE: he door gap varies depending on the stationary panel thickness and the mounting plate height. Use the table to cross-reference the plate height based on the front panel thickness and door gap. Abbreviations FP = Front panel thickness D = Depth = Plate height P = Door protrusion S = Side arm protrusion Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 27

30 CLIP top 110 diagonal hinges 110 Features hree-dimensional adjustment Available with INSERA attachment All metal hinge, nickel-plated Overlay application Inside corner Calculating door width 45 o mitered panel straight side panel Step 1. Using the boring distance () determined in the reveal table, cross-reference to find the side gap distance (Y) in the table below. overlay Step 2. Using the following formula to find the door width. Door width = interior width minus (Y x 2). reveal Example: Interior width = 400 mm, side gap (Y) = 4.5 mm. 391 = 400 minus (4.5 x 2) Y overlay reveal 1.5 Y interior width door width reveal Overlay = boring distance Reveal = boring distance NOE: Reveal based on (3/4") side panel Y = side gap = boring distance NOE: ased on (3/4") door thickness Diagonal hinges Self close Diagonal hinges Self close Abbreviations Screw-on Screw-on = Plate height Press-in Press-in Y = Side gap INSERA INSERA lum, Inc. Subject to technical modifications without notice

31 CLIP top 95 mini hinges 95 Features For small doors or doors with small frames Side adjustment of +0.5 mm to -3.5 mm 26 mm drill bit required (1" cannot be used) hree-dimensional adjustment For door thicknesses up to 26 (1") All metal hinge, nickel-plated Ø26 38 Minimum reveal table = boring distance = door thickness For thickness greater than 26 trial app. recommended CLIP top Overlay Partial/twin overlay Inset Frame Frame Frame min reveal 12.5 overlay 12.5 overlay NOE: For this application use a half-cranked hinge and mounting plate Panel W Panel W Panel W overlay 12.5 reveal 12.5 reveal Overlay P S fixed distance = boring distance = 10 NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Overlay P S fixed distance = boring distance =.5 Reveal W P S = boring distance Reveal P S fixed distance = boring distance = -8 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion = Door thickness W = Side panel width Straight-arm Self close alf-cranked Self close Full-cranked Self close Screw-on Screw-on Screw-on Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 29

32 CLIP top 95 glass door hinges 95 Features For glass thickness of 4.5 mm to 7 mm Side adjustment of +5 mm to -3.5 mm hree-dimensional adjustment Fixing screws included ( ) 26 mm drill bit required (1" cannot be used) Minimum reveal table = boring distance = door thickness For thickness greater than 7 trial app. recommended Overlay Partial/twin overlay Inset Panel 66 W Panel Panel 32 W Set mounting plate back by glass thickness and height of cover cap overlay reveal Cover caps for door front oring pattern D-shape cap Required on door front D-shape available in polished chrome Round available in black and polished chrome 5.5 to to 7 Round cap Ø to 7 D-shape cover cap Round cover cap Overlay P S fixed distance = boring distance = 10 NOE: 4.5 plate is only for use in frame cabinets, 9 plate is only for panel cabinets Reveal W P S fixed distance = boring distance =.5 Reveal P S fixed distance = boring distance = -8 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion = Door thickness W = Side panel width Straight-arm Self close alf-cranked Self close Full-cranked Self close Screw-on Screw-on Screw-on lum, Inc. Subject to technical modifications without notice

33 CLIP top 60 bi-fold hinges 60 Features Spiral tech side adjustment for door gap Spiral tech depth adjustment for in/out Four-dimensional adjustment All metal hinge, nickel-plated CLIP top Inside corner application 60 use with 155 or 170 hinge on adjacent door Calculating door sizes he doors for a CLIP top bi-fold application can be of equal or unequal width. o calculate the door width (DW) of each door follow the step-by-step below. Step 1. Add the interior width to the side panel width (W) Step 2. Subtract door thickness () and reveal (R) Step 3. Subtract gap (G) and bumper thickness behind adjacent door With flat panel doors With profile doors Formula: DW = (IW + W) minus minus R minus G frame adapter plate Example: DW = (500 + ) DW = 496 mm IW W G 12.5 DW R IW DW Adjustment General specifications he Spiral ech cam adjustment of the CLIP top bi-fold hinge allows +4/-7 mm adjustment = 0 18 W G R Abbreviations DW = Door width G = Gap = Plate height i-fold hinges Self close mm bore IW = Interior width R = Reveal Screw-on = Door thickness Press-in W = Side panel width Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 31

34 Euro hinge cover caps inge arm cover cap P (lum logo) M M M2203 Nylon Steel 100, 107, 110, 110 +, 120, 120 +, thick door Straight-arm 90M and bi-fold hinges Embossed lum logo P Cranked-arm 94M hinges hinges Diagonal 45, blind corner, narrow aluminum door hinges 90M Angled, mini and glass door hinges with straight or cranked-arms 90M NOE: Custom logo cover caps available (minimums apply) inge cup cover cap For use with CLIP top hinges only Suitable for screw-on, press-in and EXPANDO hinge cups for CLIP top 107, 120, 120 +, thick door and blind corner hinges Clip on attachment/removal Steel, nickel-plated inge cup cover cap For use with CLIP top 110 and hinges only Suitable for screw-on, press-in and EXPANDO hinge cups Clip on attachment/removal Steel, nickel-plated inge cup cover cap inge cup cover cap mm spacer inge cup spacer Reduces overlays by 3 mm Mounts under CLIP wing mounting plates rown nylon 1.5 mm spacer for use under the hinge cup For use with CLIP top 110 and hinges only For retrofitting existing doors with a cup depth less than mm 3 mm spacer inge cup spacer lum, Inc. Subject to technical modifications without notice

35 CLIP top and CLIP angle restriction clips Angle restriction clip for 107 hinges 86 Reduces opening angle of the CLIP top and CLIP 107 to 86 For use with CLIP top and CLIP 107 hinges only Installs quickly, easily and tool-free Non-removable lack nylon CLIP CLIP top 86 Angle restriction clip Angle restriction clip for 110 hinges 1 Reduces opening angle of the CLIP top 110 and to 86 For use with CLIP top 110 and hinges only Installs quickly, easily and tool-free either before or after the hinge has been installed lack nylon 2 86 Angle restriction clip Angle restriction clip for 170 hinges 0 Reduces opening angle of the CLIP top 170 to 0 Required for special applications of the 170 hinge Installs quickly, easily and tool-free lack nylon 0 Angle restriction clip Angle restriction clips for 155 hinges 110 Reduces opening angle of CLIP top 155 hinge to 110 or 92 For use with 155 hinges only Installs quickly, easily and tool-free Gray nylon 110 Angle restriction clip N 92 Angle restriction clip N09 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 33

36 CLIP top angled hinges CLIP top angled hinges from +45 to -45 Angled hinges provide a tremendous array of possibilities for the professional cabinet designer. Specifically designed for panel constructed (frameless) cabinets, the system accommodates cabinet front angles from -45 to +45, in 5 increments. his is achieved by combining any of ten angled hinges, or three standard hinges with a wedge spacer and any of five standard CLIP mounting plates. Step 1. On page 38, the angle-to-style cross-reference provides an overview of all the angled hinge applications available to assist with your specific application. Step 2. Once the cabinet front angle is determined, select the row for that angle from the first column. here are five different possibilities for positive angles and two for negative angles. All CLIP top hinges feature "Spiral ech" depth adjustment which eliminates loosening and retightening the adjustment screws. When the doors are ready to be attached to the cabinet, the time-proven CLIP mechanism connects the hinge arm to the mounting plate, again without tools. All components are nickel-plated and have self-closing action, eliminating the need for additional hardware. Step 3. Cross-reference the angle to the style to find the hinge/plate/wedge combination and the specification number. Specifications on pages 39 through 45 are in numerical order and show all the details lum, Inc. Subject to technical modifications without notice

37 Positive angle hinges A A II* 79A III* 79A9496 Angled +45 I* 79A II* III* 79A9498 *hese angled hinges are marked I, II, or III on the hinge arm for differentiation (see photo) Negative angle hinges A A A5490 Standard thick door hinges used in angled applications 95 straight-arm half-cranked full-cranked Angled spacer wedges for positive and negative angled hinges 2 mm thickness 4 mm thickness 5 mm thickness 7 mm thickness A A A A5070 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 35

38 Angled cabinet configurations Match desired configuration to angle-to-style cross-reference chart on page 38 equal equal lum, Inc. Subject to technical modifications without notice

39 Match desired configuration to angle-to-style cross-reference chart on page 38 Angled Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc.

40 Angle-to-style cross-reference LUMOION inside he chart on this page shows the hinge, plate and wedge (or spacer) needed for each angled application. he legend below shows the order of the part numbers. Application number hinge CLIP top hinge Part number plate CLIP mounting plate Part number wedge/spacer may or may not be required Part number wedge plate hinge front angle Positive angles Negative angles maximum overlay partial overlay corner merge inset door mitered corner maximum overlay inset door A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A lum, Inc. Subject to technical modifications without notice

41 Maximum overlay specifications Positive angle applications minimum 20 minimum =5 OL= =5 OL= =5 OL=16 Angled A A A A minimum 20 minimum =5 OL=16 79A A A A A minimum 25 minimum =5 OL= =5 OL= =5 OL=16 40 =5 OL=16 45 =5 OL= A A A A A Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 39

42 Partial overlay specifications Positive angle applications minimum minimum =5 OL=15.5 =5 OL=16 15 =5 OL= A A A A minimum =5 OL= =5 OL= =5 OL=8 79A A A A minimum minimum =5 OL= =5 OL= =5 OL=3 79A A A A A lum, Inc. Subject to technical modifications without notice

43 Corner merge specifications Positive angle applications minimum 25 minimum 20 minimum Angled = = = A A A A A minimum =5 25 =5 30 = A A A A minimum =5 45 = A A A Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 41

44 Inset door specifications Positive angle applications minimum 20 minimum 20 minimum R= R= = = A A A A A R= R= = R=1 R=1 25 =5 25 =5 30 = A A A minimum minimum R=1 =5 40 R=1 =5 45 R=2 = A A A A A lum, Inc. Subject to technical modifications without notice

45 Mitered corner specifications Positive angle applications NOE: 64 Miter door 65 Miter side 40 Radius edges to fit rial application recommended R=1 minimum 20 =11 Angled 23 79A A NOE: NOE: NOE: 61 Miter door 62 Miter side 48 Radius edges to fit rial application recommended Miter door 70 Miter side 45 Radius edges to fit rial application recommended 63 Miter door 70 Miter side 50 Radius edges to fit rial application recommended 36 minimum R=1 =9.5 79A A A A R=1 = R=1 =9.5 NOE: 32 NOE: 62 Miter door 70 Miter side 55 Radius edges to fit rial application recommended 64 Miter door 70 Miter side 55 Radius edges to fit rial application recommended minimum R=1 = R=1.5 = A A A Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 43

46 Maximum overlay specifications Negative angle applications minimum 20 minimum =5 OL=10 14 =5 OL=15 =5 OL= A A A A minimum 20 minimum =5 OL=8.5 =5 OL=15 =5 OL=14 79A A A A A minimum 20 minimum =5 OL=9.5 =5 OL= =5 OL=11 79A A A A A lum, Inc. Subject to technical modifications without notice

47 =5 Inset door specifications Negative angle applications minimum 20 minimum R=1 = =6 R= =9 R= A A A A minimum 20 minimum R=2.5 R=2.5 =8 =10 79A A A A Angled R=2 hinge mounting plate spacer 79A Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 45

48 CLIP 100 hinges 110 Features hree-dimensional adjustment Available with INSERA attachment For door thicknesses up to 24 (15/16") All metal hinge, nickel-plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness For thickness greater than 24 trial app. recommended Overlay Partial/twin overlay Inset Frame Frame Frame min. Panel W overlay Panel W overlay NOE: his application uses a half-cranked hinge and mounting plate Panel 11 reveal overlay reveal reveal Overlay P S fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Overlay P S fixed distance = boring distance = 1.5 Reveal W P S = boring distance Reveal P S fixed distance = boring distance = -7 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion = Door thickness W = Side panel width Straight-arm Self close Free swing Screw-on 71M M2550.L Press-in 71M M2580.L INSERA 71M2590 alf-cranked Self close Free swing Screw-on 71M M2650.L Press-in 71M2680 INSERA 71M2690 Full-cranked Self close Free swing Screw-on 71M M2750.L Press-in 71M M2780.L INSERA 71M lum, Inc. Subject to technical modifications without notice

49 CLIP 107 hinges 107 Features hree-dimensional adjustment For door thicknesses up to 22 (7/8") 86 angle restriction clip available ( ) All metal hinge, nickel-plated Add-on LUMOION soft close available Minimum reveal table = boring distance = door thickness For thickness greater than 22 trial app. recommended Overlay Partial/twin overlay Inset Frame Frame Frame Panel W overlay Panel W overlay NOE: his application uses a half-cranked hinge and mounting plate Panel min. reveal W CLIP overlay reveal reveal Overlay P S fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in face frame cabinets, 9 plate is only for panel cabinets Overlay P S fixed distance = boring distance = 1.5 Reveal W P S = boring distance Reveal P S fixed distance = boring distance = -7.5 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion = Door thickness W = Side panel width Straight-arm Self close alf-cranked Self close alf-cranked Self close Press-in 75M1580 Press-in 75M1680 Press-in 75M1680 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 47

50 CLIP mounting plates Standard one-piece wing mounting plates Wood screw Steel, nickel-plated Attached with #6 x 5/8" wood screws eight adjustment ±3 mm 32 * 0 plate height () 173L plate height () 173L60 System screw 11.5 Steel, nickel-plated Attached with pre-mounted Ø5 mm system screws ( E) eight adjustment ±3 mm Ø5 32 * 0 plate height () 173L plate height () 173L80 EXPANDO 11.5 Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels ( ) eight adjustment ±2 mm Ø5 32 * 0 plate height () 174E EXPANDO (twin application) 7.5 Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels for twin application ( ) eight adjustment ±2 mm 32 Ø5 * 0 plate height () 174E610Z System screw 11.5 Zinc die-cast, nickel-plated Attached with pre-mounted Ø5 mm system screws ( E) eight adjustment ±3 mm *Add additional wood screw if used with wide angled hinges 32 * Ø5 0 plate height () 175L plate height () 175L80 9 plate height () 175L lum, Inc. Subject to technical modifications without notice

51 Cam adjustable wing mounting plates Wood screw Steel, nickel-plated Attached with #6 x 5/8" wood screws Cam height adjustment ±2 mm 32 0 plate height () plate height () 170 System screw 11.5 Steel, nickel-plated Attached with #7 x 5/8" wood screws or Ø5 x mm system screws Cam height adjustment ±2 mm Ø5 32 EXPANDO plate height () plate height () Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels ( ) Cam height adjustment ±2 mm CLIP plates 32 Ø5 * 0 plate height () E 3 plate height () 17470E EXPANDO (twin application) 7.5 Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels for twin application ( ) Cam height adjustment ±2 mm 32 Ø5 * 0 plate height () ZE INSERA 11.5 Steel (closing lever zinc die-cast, nickel-plated) ool-free assembly with INSERA self-anchoring feature Cam height adjustment ±2 mm Ø5 *Add additional wood screw if used with wide angled hinges 32 * 0 plate height () I 3 plate height () 17470I Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 49

52 CLIP mounting plates Standard two-piece wing mounting plates Wood screw Zinc die-cast, nickel-plated Attached with #6 x 5/8" wood screws eight adjustment ±2 mm * plate height () plate height () plate height () System screw Zinc die-cast, nickel-plated Attached with #7 x 5/8" wood screws or Ø5 x mm system screws eight adjustment ±2 mm Ø5 0 plate height () plate height () plate height () plate height () plate height () *Add additional wood screw if used with wide angled hinges Cam adjustable In-line mounting plates Wood screw Steel, nickel-plated Attached with #6 x 5/8" wood screws Cam height adjustment ±2 mm Use of mounting plate template recommended 0 plate height () Press-in 11.5 Steel, nickel-plated Pre-attached with 10 mm dowels Cam height adjustment ±2 mm Use of insertion ram MZM.0053 required Ø plate height () EXPANDO 11.5 Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels Cam height adjustment ±2 mm Use of mounting plate template recommended Ø plate height () E 3 plate height () 17730E *Add additional wood screw if used with wide angled hinges lum, Inc. Subject to technical modifications without notice

53 Face frame adapter plates Face frame adapter plates Cam adjustable center mount 40 Steel, zinc die-cast and nickel-plated Attached with #7 x 3/4" wood screws Center mount 9.5 (3/8") Cam height adjustment ±2 mm not for use with INSERA hinges plate height () plate height () plate height () plate height () Cam adjustable off-center mount Steel, zinc die-cast and nickel-plated Attached with #7 x 3/4" wood screws For use with INSERA hinge cups Off-center mount 12.5 (1/2") Cam height adjustment ±2 mm 0 plate height () Center mount Zinc die-cast, nickel-plated Attached with #7 x 3/4" wood screws Center mount 9.5 (3/8") eight adjustment ±2 mm 3 plate height () 175L CLIP plates Off-center mount Zinc die-cast, nickel-plated Attached with #7 x 3/4" wood screws Off-center mount 12.5 (1/2") eight adjustment ±2 mm plate height () 175L plate height () 175L plate height () 175L With flange Recommended when using 170 and zero protrusion hinges on face frame cabinets Zinc die-cast, nickel-plated Attached with #7 x 3/4" wood screws Off-center mount 12.5 (1/2") eight adjustment ±2 mm 0 plate height () 175L NOE: Use of PLAEMAE recommended with all face frame adapter plates Inset face frame adapter russ head screw Zinc die-cast, nickel-plated Attached with #8 x 3/4" truss head screws Can be used with applied bead molding Cam height adjustment ±2 mm Use with half-cranked hinges only Wide angle hinges not recommended Use of PLAEMAE required for installation 9 plate height () Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 51

54 52 20 lum, Inc.

55 LUMOION for doors LUMOION inside Soft closing solutions for every application LUMOION for doors soft closing mechanisms can be quickly integrated into cabinets. It will work for almost any application and does not require any change to the hinge assembly. LUMOION redefines the phrase qua lity of motion. he system is quick and easy to install and once installed, creates a quiet closing motion. he braking action increases with the force of the door allowing it to close softly. his technology enables LUMOION to adjust itself automatically to each door size, weight and closing speed. Soft closing motion every time due to adaptability he integrated overload safety feature protects the LUMOION system from damage through abuse LUMOION lasts the lifetime of the cabinet ensuring that your customers remain satisfied > inge planning tools lum has downloadable Excel spreadsheets that help determine the hinge that is right for your application. Planning tools are easily accessible on our website at blum.com/planning Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 53

56 LUMOION for doors overview for Euro hinges LUMOION inside Recommended LUMOION Standard hinge Standard hinge Standard hinge Standard hinge Standard hinge Standard hinge hick door hinge Straight-arm hinge, 0 plate Straight-arm hinge, 0 plate Straight-arm hinge, 0 plate Straight-arm hinge, 0 plate Straight-arm hinge, 0 plate Straight-arm hinge, 0 plate Straight-arm hinge, 0 plate 973A A A A A A A Overlay 971Axxxx 971Axxxx 971Axxxx 971Axxxx 971Axxxx 971Axxxx 971Axxxx 970A A A A A A A1002 Straight-arm hinge, 9 plate Straight-arm hinge, 9 plate Straight-arm hinge, 9 plate Straight-arm hinge, 9 plate Straight-arm hinge, 9 plate Straight-arm hinge, 9 plate Straight-arm hinge, 9 plate Partial/twin overlay 973A A A A A A A alf-cranked hinge, 0 plate alf-cranked hinge, 0 plate alf-cranked hinge, 0 plate alf-cranked hinge, 0 plate 973A A A A A A A A A A A1002 Straight-arm hinge, 18 plate Straight-arm hinge, 18 plate Straight-arm hinge, 18 plate Straight-arm hinge, 18 plate Straight-arm hinge, 18 plate Straight-arm hinge, 18 plate Straight-arm hinge, 18 plate 973A A A A A A A alf-cranked hinge, 9 plate alf-cranked hinge, 9 plate alf-cranked hinge, 9 plate alf-cranked hinge, 9 plate Inset 973A A A A0600 Full-cranked hinge, 0 plate Full-cranked hinge, 0 plate 973A A A A A A A A A1002 NOE: he overview chart shows all possible LUMOION applications. he recommended LUMOION part number is marked in orange lum, Inc. Subject to technical modifications without notice

57 LUMOION inside Zero protrusion hinge Standard hinge Aluminum door hinge Glass door hinge Mini hinge lind corner hinge overlay and inset Angled hinges: +30 II, +45 I,+45 II Straight-arm hinge, 0 plate Straight-arm hinge, 0 plate Straight-arm hinge, 0 plate 973A A A Axxxx 971Axxxx 971Axxxx 971Axxxx 970A A A A A A A1002 Straight-arm hinge, 9 plate Straight-arm hinge, 9 plate Straight-arm hinge, 9 plate 973A A A alf-cranked hinge, 0 plate 973A0600 LUMOION 970A A A A A A A1002 Straight-arm hinge, 18 plate Straight-arm hinge, 18 plate Straight-arm hinge, 18 plate 973A A A alf-cranked hinge, 9 plate 973A0600 Full-cranked hinge, 0 plate 973A A A A A A A A1002 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 55

58 LUMOION 973A for CLIP top and CLIP hinges Features Soft-closing feature for CLIP top and CLIP hinges Offers the same quality of motion as drawer systems with LUMOION Automatically adjusts to the closing force of the door Simple attachment to the hinge arm Designed for use with lum Euro hinges only Nickel-plated steel and gray nylon For straight-arm hinges 36 CLIP top 107 CLIP top 110 CLIP top CLIP top 120 CLIP top CLIP top 95 thick door CLIP top 120 aluminum door CLIP 100 CLIP 107 Straight-arm 973A For half-cranked arm hinges CLIP top 110 CLIP top 120 CLIP top 95 thick door CLIP 100 CLIP 107 alf-cranked arm 973A0600 For full-cranked arm hinges CLIP top 110 CLIP top 95 thick door CLIP Full-cranked arm 973A lum, Inc. Subject to technical modifications without notice

59 LUMOION inside Specifications For 170 hinges CLIP top 170 straight-arm CLIP top 170 half-cranked X S inge X S CLIP top 170 straight-arm max. CLIP top 170 half-cranked max. NOE: Additional clearance of 41 mm needed above and below for interior roll-out 973A6000 For 155 hinges CLIP top 155 straight-arm CLIP top 155 half-cranked X S inge X S CLIP top 155 straight-arm CLIP top 155 half-cranked NOE: Additional clearance of 41 mm needed above and below for interior roll-out 973A7000 LUMOION Attachment Attach to the square hole in the hinge arm 1 Pull forward and down on the front Removal Pull forward and up simultaneously 2 Push down on the back LUMOION per door LUMOION 973A is designed for one LUMOION per self-closing hinge, however, quantities may vary depending on door size and weight Small or light doors may only require one LUMOION rial application recommended LUMOION 973A inges Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 57

60 LUMOION 971A for Euro hinges Product Description Soft-closing feature for CLIP top and CLIP straight-arm hinges Offers the same quality of motion as drawer systems with LUMOION Adjustable to various door sizes and weights (+3/-7 mm range) Installed onto hinge-side panel For use with straight-arm hinge and either 0 mm or 3 mm mounting plate only Nickel-plated steel and gray nylon Application Wing plate (screw-on) mm setback, 32 mm apart Attach with #6 x 5/8" wood screws 0 mm 971A0500 Installation screw 606N or 606P Face frame adapter plate (screw-on) 9.5 mm setback, 32 mm apart Attach with #6 x 5/8" wood screws mm 971A mm 971A2700 Installation screw 606N or 606P lum, Inc. Subject to technical modifications without notice

61 LUMOION inside Specifications LUMOION per door For optimum LUMOION effect, LUMOION 971A should be installed onto the hinge-side panel centered between the two hinges all or heavy doors may require an additional LUMOION 971A between the hinges rial application recommended LUMOION 973A inges 0 mm LUMOION application For all hinges with a straight-arm and a 0 mm mounting plate 25 3 mm LUMOION application For all hinges with a straight-arm and a 3 mm mounting plate LUMOION 33 NOE: 95 thick door straight-arm hinge requires 3 mm LUMOION Adjustment Use a Phillips or POZI screwdriver to adjust the contact point in or out (+3/-7 mm). Adjust out for larger, heavier doors or adjust in for smaller, lighter doors Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 59

62 LUMOION 970A for Euro hinges Product Description Soft-closing feature for CLIP top and CLIP hinges Offers the same quality of motion as drawer systems with LUMOION Automatically adjusts to the closing force of the door Installed into the top and/or bottom panel or with adapter plates on hinge-side Gray nylon Application LUMOION 970A LUMOION per door LUMOION 970A is designed for two LUMOION per door, however, one may be enough depending on door size and weight Small or light doors may only require one LUMOION rial application recommended LUMOION 970A 970A1002 LUMOION 973A inges Face frame adapter (screw-on) mm setback, 32 mm apart Can also be used in panel cabinets Attach with #6 x 5/8" wood screws Nickel-plated steel Screw-on Installation screw 606N or 606P /32 mm adapter (EXPANDO) mm setback, 32 mm apart EXPANDO version installs with pre-attached screws Nickel-plated steel Ø EXPANDO E1 In-line adapter (screw-on) mm setback, 32 mm apart wo-piece design Attach with #6 x 5/8" wood screws Nickel-plated steel and gray nylon Screw-on Installation screw 606N or 606P lum, Inc. Subject to technical modifications without notice

63 LUMOION inside LUMOION 970A Standard applications For angled applications he charts below provide the boring distance based on the application and mounting plate height X boring distance (X) in mm 3 mm 35 boring distance (X) in mm min. mounting plate height application, refer to pages 38 to 45 Ø Standard application mounting plate height Overlay boring distance win boring distance Inset boring distance Inset with straight-arm boring distance 0 mm 32 0 mm 41 0 mm mm 50 3 mm 35 3 mm 44 3 mm 53 6 mm 38 6 mm 47 9 mm 41 9 mm 50 lind corner applications Inset blind corner boring distance Overlay blind corner boring distance mounting plate height 0 mm 32 3 mm 51 3 mm 35 6 mm 38 Angled applications (reference angle applications page 38 to 45) Max. overlay boring distance Partial overlay boring dist. Corner merge boring distance Inset boring distance Mitered corner boring distance LUMOION Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 61

64 62 20 lum, Inc.

65 IP-ON for doors IP-ON inside Opening comfort for doors without handles Doors can be opened easily with IP-ON a light touch is all that's needed. Designed for panel or face frame (blocked out) cabinet applications Works with CLIP, CLIP top and CLIP top LUMOION free swing and self close hinges Can be bored into the side panel or used with an adjustable adapter plate Easy depth adjustment when used with an adapter plate Works for both overlay and inset applications Quick and easy installation Increased design options Requires minimal force to open and close Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 63

66 IP-ON for doors program igh quality down to the last detail he IP-ON unit can be either bored into the cabinet end panel or a attached to the cabinet interior using adapter plates. 2 he catch plate is the counterpart to IP-ON. It is available in self-adhesive or screw-on versions. 3 Free swing hinges are used with IP-ON for doors with magnet/self close hinges are used withh IP-ON for doors with bumper. he ideal location for the IP-ON mechanism, as shown in this image, is no more than 12" up the side panel or no more than 1/4 of the door width from the edge. For taller doors, IP-ON should be installed no more than 12" from the area normally pressed to open the door lum, Inc. Subject to technical modifications without notice

67 IP-ON inside Adjustments A minimum door gap of 2.5 mm should be planned when using the self-adhesive catch plate. he screw-on catch plate requires a minimum of 3 mm. In-line or wing adapter plates can be adjusted using a spiral screw (+4.5/ 1.5 mm range). he factory setting of the door gap is 2 mm. For adapter plate assembly (in-line or wing adapter plates), the door gap can be adjusted to a minimum of 1.5 mm. IP-ON boring specifications Standard IP-ON set Catch plate (screw-on) Catch plate (self-adhesive) 50 min. 2.5 (3) min. 0.5 Large IP-ON set 76 min. Ø10 Pre-boring Ø2.5 mm countersunk pilot holes required 0.6 Cleaning of the door surface is recommended 2.5 (3) min. OL = Door overlay NOE: Minimum gap of 2.5 mm with a self-adhesive catch plate or 3 mm with a screw-on catch plate IP-ON in-line and wing adapter plate specifications In-line adapter plate Catch plate (screw-on) Catch plate (self-adhesive) IP-ON 1.5 min. Wing adapter plate 1.5 min. NOE: Factory setting of door gap is 2 mm Pre-boring Ø2.5 mm countersunk pilot holes required Cleaning of the door surface is recommended OL = Door overlay NOE: Minimum gap of 2.5 mm with a self-adhesive catch plate or 3 mm with a screw-on catch plate Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 65

68 Components IP-ON set for standard doors Overlay Inset 50 min For use with lum Euro free swing hinges For door heights less than 48" Nylon gray mechanism with magnet tip Works for both overlay and inset applications Can be bored into the panel or used with an adjustable adapter plate 50 min Set includes: IP-ON mechanism Self-adhesive catch plate Screw-on catch plate Wood screw NOE: Due to various door weights and sizes, trial application recommended Standard door set IP-ON set for large doors Overlay Inset 76 min For use with lum Euro free swing hinges on larger doors For door heights greater than 48 Nylon gray mechanism with magnet tip Works for both overlay and inset applications Can be bored into the panel or used with an adjustable adapter plate 76 min Set includes: IP-ON mechanism Self-adhesive catch plate Screw-on catch plate Wood screw NOE: Due to various door weights and sizes, trial application recommended Large door set 955A1004 IP-ON for self closing hinges Overlay Inset 76 min 76 min For use with lum Euro self close hinges For door widths greater than 10" Nylon gray mechanism with bumper tip Push out distance 38 mm Works for both overlay and inset applications Can be bored into the panel or used with an adjustable adapter plate New IP-ON with bumper compatible with existing IP-ON adapter plates Ideal location for IP-ON mechanism is no more than 12" up the side panel or no more than 1/4 of the door width from the edge NOE: Due to various door weights and sizes, trial application recommended Self closing hinges 955A lum, Inc. Subject to technical modifications without notice

69 IP-ON inside IP-ON in-line adapter plate (screw-on) 77.5 wo-piece, nylon gray 20 mm setback, 32 mm apart Door gap factory setting 2 mm Adjustment range +4.5 mm to -1.5 mm Application Setback Overlay 20 Inset 22 + door thickness Screw-on in-line adapter NOE: For face frame applications, blocking out may be required Installation screw 606N or 606P IP-ON wing adapter plate (screw-on) 77.5 One-piece, nylon gray mm setback, 32 mm apart Door gap factory setting 2 mm Adjustment range +4.5 mm to -1.5 mm IP-ON Application Setback Overlay Inset 39 + door thickness Screw-on in-line adapter NOE: For face frame applications, blocking out may be required Installation screw 606N or 606P Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 67

70 68 20 lum, Inc.

71 COMPAC hinges Face frame hinges for the life of your cabinet COMPAC hinges are available for partial and full overlay doors. Some advantages of COMPAC hinges are: Small profile for face frame cabinets LUMOION soft close available 38/39 series Nickel-plated steel construction 38N and 38C/39C: three-dimensional adjustment 38.: height adjustment 33 series Zinc die-cast, nickel-plated steel construction wo-dimensional adjustment Wide variety of small and large overlays COMPAC LUMOION hinges with integrated soft close are also available > inge planning tools lum has downloadable Excel spreadsheets that help determine the hinge that is right for your application. Planning tools are easily accessible on our website at blum.com/planning Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 69

72 COMPAC general specifications Screw-on hinge attachment Use #6 wood screws Press-in hinge attachment Pre-attached Ø8 dowels installed with lum knock-in tool or MINIPRESS with COMPAC insertion ram. Mounting plate attachment One-piece assembly wo-piece assembly COMPAC 39C/38C wraparound COMPAC 38N wrap or edge COMPAC 38. wrap or edge COMPAC 33 edge mount COMPAC 33 face mount Minimum reveal inge cup centerpoint A minimum reveal per door is required to keep the door from binding and varies depending on door thickness (see minimum reveal table for each hinge). reveal Cup centerpoint and MINIPRESS/MINIDRILL setback position is 20.5 (/16") for COMPAC hinges. NOE: Maximum door thickness 3/4" 3/4" Ø8 45 door Ø (1/8") 20.5 (/16") hree-way independent adjustment Side adjustment Depth adjustment eight adjustment Side adjustment is possible on all COMPAC hinges except 38. series. COMPAC 39C, 38C and 38N have cam side adjustment. COMPAC 39C, 38C and 38N have cam depth adjustment. All COMPAC hinges are independently height adjustable lum, Inc. Subject to technical modifications without notice

73 COMPAC 38N hinges for partial overlay 105 Features 105 opening angle One piece assembly Wraparound or edge mount 7/16" cup depth ±1/8" height adjustment ±1/16" side adjustment +3/32", -1/32" cam depth adjustment Steel, nickel-plated Can be used with LUMOION 971A9700 Minimum reveal oring pattern Dimensions 11 cabinet 3/4" 3/8" pilot hole 1/8" cup depth door 3 Ø35 Ø8 45 7/16" 7/16" 105 gap 3/16" factory setting, adjusts +3/32" -1/32" 1/8" 3/4" overlay NOE: Maximum door thickness 3/4" Adjustment Wraparound hinges cam depth adjustment height adjustment cam side adjustment Overlay Screw-on 47 Press-in 3/8" 38N355C.06 38N358C.06 1/2" 38N355C.08 38N358C.08 5/8" 38N355C.10 38N358C.10 3/4" 38N355C.12 38N358C.12 Edge mount hinges COMPAC Calculating door protrusion Door overlay Door protrusion 3/8" 1/4" 1/2" 1/8" 5/8" 0 3/4" 0 Overlay Screw-on 47 Press-in 1/2" 38N355CE08 38N358CE08 Installation screw russ head installation screw 834 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 71

74 COMPAC 38C hinges for full overlay 107 Features 107 opening angle One piece assembly Wraparound mount 7/16" cup depth ±1/8" height adjustment ±1/16" side adjustment +3/32", -1/32" cam depth adjustment Steel, nickel-plated Can be used with LUMOION 971A9700 Minimum reveal sq. edge minimum reveal 3/4" door = 9/32" based on square edge doors oring pattern Dimensions cabinet door 3/4" 3 Ø8 5/16" 3/8" Ø35 45 pilot hole 1/8" overlay 1/8" 11 cup depth 107 gap 3/16" factory setting, adjusts +3/32" -1/32" NOE: Maximum door thickness 3/4" Adjustment Wraparound hinges cam depth adjustment height adjustment cam side adjustment Overlay Screw-on 47 Press-in 1-1/4" 38C355C.20 38C358C /16" 38C358C /8" 38C358C /2" 38C358C /16" 38C358C.25 Installation screw russ head installation screw lum, Inc. Subject to technical modifications without notice

75 COMPAC 39C hinges for full overlay 110 Features 110 opening angle One piece assembly Wraparound mount 1/2" cup depth ±1/8" height adjustment ±1/16" side adjustment +3/32", -1/32" cam depth adjustment Steel, nickel-plated Can be used with LUMOION 971A9700 Minimum reveal oring pattern Dimensions cabinet 3/4" 3 door Ø8 5/16" 3/8" Ø35 45 pilot hole 1/8" cup depth gap 3/16" factory setting, adjusts +3/32" -1/32" overlay 1/8" NOE: Maximum door thickness 3/4" Adjustment Wraparound hinges cam depth adjustment height adjustment cam side adjustment Overlay Screw-on 47 Press-in 1" 39C355C.16 39C358C /4" 39C355C.20 39C358C /16" 39C355C.21 39C358C /8" 39C355C.22 39C358C /2" 39C355C.24 39C358C /16" 39C358C.25 COMPAC Installation screw russ head installation screw 834 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 73

76 COMPAC 33 hinges 110 Features 110 opening angle wo piece assembly Edge or face mount 1/2" cup depth ±9/64" height adjustment -1/8" side adjustment only Zinc die-cast hinge and mounting plates Can be used with LUMOION 971A9700 Minimum reveal sq. edge minimum reveal 3/4" door = 3/16" based on square edge doors oring pattern Mounting cabinet 3/4" 3 door Ø8 3/8" Ø35 45 pilot hole 1/8" cup depth NOE: Maximum door thickness 3/4" COMPAC 33 spacer For use with profile or thin doors with a cup depth less than mm 1.5 mm spacer placed under the hinge cup Clear nylon Attachment options Edge mount mounting plate hinge cup Face mount spacer Overlay Screw-on 47 Press-in COMPAC 33 spacer Installation screw Wood screw 606N or 606P lum, Inc. Subject to technical modifications without notice

77 COMPAC 33 mounting plates Edge mount specifications 3/8" Minimum overlay of 1/4" using a edge mount plate Maximum overlay of 1-5/8" using a edge mount plate 1-3/8" 1/8" 1/8" 110 P overlay 110 overlay Edge mount mounting plates * extra screw location Zinc die-cast, nickel-plated Attaches with #6 x 5/8" wood screws (606N or 606P) Overlays from 1/4" to 1-5/8" NOE: An additional screw is required on mounting plates with 1-3/8" to 1-5/8" overlays to insure stability. Install after height adjustments have been made. Overlay inge arm protrusion (S) Door protrusion (P) Mounting plate 1/4" 1-1/8" 1/2" /2" 7/8" 1/4" /8" 3/4" 1/8" /4" 5/8" " 3/8" /8" 1/4" /4" 3/16" *1-3/8" 3/16" *1-1/2" 3/16" *1-5/8" 3/16" Face mount mounting plates Zinc die-cast, nickel-plated Attaches with #6 x 5/8" wood screws (606N or 606P) Overlays 1-3/8" or greater 9/16" COMPAC 1-1/4" Overlay Face mount mounting plate Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 75

78 COMPAC 38. hinges for partial overlay 105 Features 105 opening angle One piece assembly Self-closing Wraparound mount 7/16" cup depth ±1/8" height adjustment Steel, nickel-plated Can be used with LUMOION 971A9700 Minimum reveal square edge Features minimum reveal 3/4" door = 3/16" based on square edge doors oring pattern Dimensions cabinet 3/4" 3 door Ø8 3/4" 3/8" Ø /16" 11 pilot hole 1/8" cup depth /16" 105 1/8" overlay NOE: Maximum door thickness 3/4" Adjustment Wraparound height adjustment 47 Overlay Press-in 1/2" Distance spacer for 38. hinges Decreases door overlay in 1/32" increments Can be stacked to achieve desired overlay reduction Zinc-coated steel decrease overlay by adding spacers spacer Installation screw russ head installation screw 834 overlay 38. distance spacer lum, Inc. Subject to technical modifications without notice

79 LUMOION 971A for COMPAC hinges LUMOION inside LUMOION 971A poly-bag set Can be used for all COMPAC overlays 1-1/4" type 17 tip Set includes: LUMOION mechanism (971A9700) Spacer (971A9709) #8 x 1-1/4 type 17 wood screw #8 x 2 type 17 wood screw 2" Poly-bag set 971A Full overlay Partial overlay Full overlay 1" or greater overlay Partial overlay less than 1" overlay 15/16" 2-7/8" /16" 15/16" 2-7/8" 1-7/16" LUMOION 971A9700 LUMOION 971A9700 Spacer 971A9709 Installation screw (1-1/4") 8114Z Installation screw (2") 8200Z Specifications Mounting LUMOION for doors mounts anywhere on the hinge-side stile of the cabinet using a 1-1/4" screw or 2" screw when using spacer Attachment of partial overlay spacer he partial overlay spacer snaps onto the side of the LUMOION for easier mounting Adjustment Use a Phillips or POZI screwdriver to adjust the contact point in or out (+5/-5 mm). Adjust out for larger, heavier doors or in for smaller, lighter doors LUMOION per door For optimum LUMOION effect, one LUMOION 971A should be installed for most applications all or heavy doors may require an additional LUMOION 971A rial application recommended COMPAC LUMOION 973A inges Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 77

80 inge accessories COMPAC cover caps COMPAC 38N cover cap For use with COMPAC 38N hinges Clip on attachment/removal Available blank or with printed custom logo (minimums apply) Steel, nickel-plated COMPAC 38C/39C cover cap For use with COMPAC 38C/39C hinges only Clip on attachment/removal Available blank/embossed blum logo or with printed custom logo (minimums apply) Steel, nickel-plated 38N cover cap lank Embossed lum logo 38C C3508.P Dowel cross-reference chart lum press-in and EXPANDO dowels simplify installation Use the charts below to find the proper hinge-to-dowel combination Ø8 mm dowels NOE: All dowels for Ø8 mm holes require a #6 x 1/2" dowel screw ( ) Dowels for Ø8 mm hole type series without flange CLIP top and CLIP COMPAC square head without flange with flange installation screw 100 / / / hick door Zero protrusion Diagonal 45 lind corner i-fold 33 38C/39C 38N 38. Ø5 mm dowels ype Series/application Dowels Installation screws E /std. application E EXPANDO ZE /twin application E8Z lum, Inc. Subject to technical modifications without notice

81 Screws Deep thread wood screw For attaching hinges and mounting plates Deep thread system screw Pilot bore Ø5 (3/16") hole Ø5 #6 x 1/2", #2 Phillips 6062N #6 x 5/8", #2 Phillips 606N #6 x 5/8", #2 POZI 606P #6 x 3/4", #2 Phillips 6064N #7 x 5/8", #2 Phillips 707N #7 x 3/4", #2 Phillips 7074N #7 x 10 mm, #2 POZI G #7 x 11.5 mm, #2 POZI G #7 x mm, #2 POZI G #7 x 14.5 mm, #2 POZI G #7 x 20 mm, #2 POZI G #7 x 25 mm, #2 POZI G Pan head system screw Pilot bore Ø5 mm (3/16") hole Replacement screw for mounting plates with pre-mounted system screws ype 17 truss head screw umpers Clear in color Adhesive backing (diameter x thickness) Ø5 diameter thickness #7 x 14.5 mm, #2 POZI E #8 x 3/4", #2 Phillips x 2 mm bumper FX x 3.5 mm bumper SJ5312 win application screw Pre-bored Ø5 (3/16") hole POZI DRIVER and bits A POZI screwdriver (different from Phillips) is the most crucial tool you can use to assure that full torque is applied to all lum POZI mounting screws. POZI screws can be identified by the distinctive tick marks located in the center of the screw head recess. POZI Phillips ACCESSORIES tick marks 14 (9/16") screw (25/32") sleeve (15/16") sleeve #2 POZI DRIVER POZI DRIVER 1/4" Magnetic bit holder I OLDER #2 x 1" POZI bit insert POZI I #2X1 #2 x 1 POZI bit insert POZI I #2X2 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 79

82 Assembly aids Knock-in tool Can be used to insert all lum press-in hinges Knock-in tool ZME.0710 ECODRILL Simple device for boring lum hinge pattern Driven by electric/cordless drill (18v or higher) oring distance adjusts from 2 mm to 8 mm 9.5 door C Clamps to various door thicknesses up to 40 mm Includes drill bits (pre-installed) and two orx bits Ø35 ECODRILL M Ø8 Accessories Replacement Ø35 mm bit M31.Z35.02 Replacement Ø8 mm bit M31.Z08.02 ool set MZW.00 ECOJIG holes are: 32mm apart, mm setback 32 Used to bore Ø5 mm holes for mounting plates that are mounted with system screws, EXPANDO dowels or INSERA Also can be used to pre-bore Ø5 mm holes for EXPANDO LUMOION adapters Ø5 mm stop collar included ECOJIG Universal individual template For pre-boring mounting plates Also used for marking and pre-boring cabinet profiles, LUMOION, IP-ON adapter plates and AVENOS locating pins Calibrated scale for accurate setting Universal individual template Mounting plate template in-line wing Use with CLIP mounting plates on overlay applications on panel cabinets For wing mounting plates ( mm setback) and in-line mounting plates (20 mm setback) Simple location of mounting plate screw positions Pilot bore Ø2.5 mm holes for wood screws Mounting plate template lum, Inc. Subject to technical modifications without notice

83 QUICKFIX Drilling sleeve dimensions changed from 2.5 mm to 5 mm for drilling for in-line mounting plates Locates/matches positions of hinges and plates on cabinets and doors ransfers positions from door-to-cabinet and cabinet-to-door Adjustable stop for various door overlays For use with wing or in-line mounting plates QUICKFIX Accessories Additional CLIP template meter rail Ø5 mm drill bit D-5mm PLAEMAE adjustable M4 x 25 mm spacer screws included oring template for all lum face frame adapter plates Clamps to the frame with cam lever Adjustment knob accommodates frame thickness of 5/8" to 1" Spacer screws permit quick use without measuring Includes 2.5 mm pilot bit and drill bit extension PLAEMAE Dowelling fixture ool designed for attaching and removing dowels from hinges Mounts directly to work surface Doweling fixture INSERA boring template For boring Ø8 mm dowel holes after Ø35 mm hole is bored oring distance adjusts from 2 mm to 8 mm Also bores Ø5 mm holes for system screw mounting plates Includes drill stop collar to pilot bore Ø2.5 mm for screw-on plates INSERA boring template A LUMOION for doors boring template For pre-boring LUMOION adapters Ø10 mm drill bushing for panel edge boring Vertical guides for setting height Can be used to pre-bore for wing and in-line mounting plates Includes Ø10 mm, Ø5 mm and Ø2.5 mm stop collars LUMOION for doors boring template Assembly aids Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 81

84 Assembly aids Machines MINIPRESS P Deluxe boring and insertion machine Front adjustable boring distance with digital counter Pneumatic hold-down clamps oring depth adjustment Ruler stops (qty 4) ool kit included Dust collection attachment Optional laser center line set Accepts new 8 or 9 spindle heads Single phase 220V power hree-phase 220V power M *US M *US MINIPRESS M 110V manual boring and insertion machine 110V power with molding plug (portable) Does not require pressurized air Ruler stops (qty 4) ool kit included Dust collection attachment Accepts new 8 or 9 spindle heads Single phase 110V power M *US MINIDRILL P Standard boring machine Front adjustable boring distance Ruler stops (qty 4) ool kit included Dust collection attachment Optional laser center line, digital counter and hold down clamps sets Accepts new 8 or 9 spindle heads Single phase 220V power M * lum, Inc. Subject to technical modifications without notice

85 Machine accessories 9 spindle head 9 spindle head for use with MINIPRESS/MINIDRILL ores nine holes spaced 32 mm apart, parallel to the fence New feature quick-disconnect chucks Once aligned, does not require additional adjustment ores cabinet side panel for 32 mm system boring for lum mounting plates and runners Requires retrofit set for use with machines produced in 2009 or prior Includes: Ø3 mm allen wrench Distance spacer Drive pin Air hose 9 spindle head MZK.0S Chuck cover cap M spindle head 8 spindle head for use with MINIPRESS/MINIDRILL ores eight holes spaced 32 mm apart, perpendicular to the fence New feature quick-disconnect chucks Once aligned, does not require additional adjustment ores all MEAOX and ANDEMOX front fixing brackets and galleries ores cabinet side panels for all lum runner systems Requires retrofit set for use with machines produced in 2009 or prior Includes: Ø3 mm allen wrench Distance spacer Drive pin Air hose 8 spindle head MZK.880S Chuck cover cap M30.29 Spindle head retrofit set Required for attachment of 9 and 8 spindle heads to MINIPRESS/ MINIDRILL produced in 2009 and prior Previous boring heads MZK.1000.US and MZK.8000.US cannot be used with the retrofit set Set includes: 1 Adapter ring and shield 2 Ø5 mm allen wrench 3 Mounting bolts (qty 4) 4 Alignment pins (qty 2) 5 Alignment template 6 mm fixed depth stop (qty 2) Assembly aids Spindle head retrofit set M30..UM Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 83

86 Assembly aids Work table for M51 machine Work table for M52 machine Work table for M53 machine Work table MZA.1000 Work table MZA.5200 Work table MZA.5300 Center ruler Extension ruler Extension ruler support Center ruler, 600 (2') M Extension ruler,1250 (4") MZL.1250.US Extension ruler support MZV.2100 Ruler stop Small ruler stop Large ruler stop Left or right ruler stop Left or right ruler stop Symmetrical ruler stop Ruler stop MZS.3000 Small ruler stop MZS.2000 Large ruler stop MZS.1000 Fixed depth stop (1/2") fixed depth stop for use with M51N machines (-shaped) Fixed depth stop (1/2") fixed depth stop for use with M53. machines Digital counter set Fixed depth stop M Fixed depth stop M Digital counter set MZE.2110 old down clamp set Laser center point set reakaway clutch For use with MINIPRESS and MINIDRILL old down clamp set M US Laser center point set MZR.5300.US reakaway clutch MZK lum, Inc. Subject to technical modifications without notice

87 Euro hinge insertion ram Can be used for inserting CLIP top LUMOION, CLIP top, and CLIP press-in hinges Not for use with wide angled or specialty hinges Euro hinge insertion ram Can be used for inserting lum wide angle press-in hinges NOE: Can be used with CLIP top LUMOION 95, CLIP top 95 and CLIP 100 by adjusting ball plungers #10 insertion ram MZM #18 insertion ram MZM.0018 Euro hinge insertion ram Can be used for inserting CLIP top LUMOION, CLIP top, and CLIP press-in hinges COMPAC hinge insertion ram Can be used for inserting all lum COMPAC press-in hinges Mounting plate insertion Ram MINIPRESS insertion ram for press-in, in-line mounting plate NOE: Not for use with 170 and 155 wide angle hinges #40 insertion ram MZM.0040 #47 insertion ram MZM.0047 #53 insertion ram MZM.0053 Machine drill bits Ø5 mm drill bit (right handed) M01.Z05.D2 R Ø5 mm drill bit (left handed) M01.Z05.D3 L Ø8 mm drill bit (left handed) M01.Z08.03 L Ø10 mm drill bit (right handed) M01.Z10.02 R Ø10 mm drill bit (left handed) M01.Z10.03 L Ø5 mm Ø8 mm Ø10 mm Ø35 mm Ø20 mm drill bit (right handed) Ø35 mm with center point M01.Z20.02 R M01.Z35.02 R wist drill bits high speed steel VP-5 wist drill bit *Chuck for D-2mm *Used to pilot bore for screw-on hinges with MINIPRESS or MINIDRILL VP-5 centering bit VP-5 Ø2 mm left D-2mm Ø2.5 mm right D-2.5mm Ø5 mm right D-5mm Ø8 mm right D-8mm Ø10 mm right D-10mm Ø10 mm chuck for D-2 mm D-10 x 2mm Assembly aids Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 85

88 Notes lum, Inc.

89 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 87

90 Part number index Page no A A A A L L L L E E610Z E E I E8Z ZE E l L L L L L L L L E E C C3508.P 78 38C355C C358C C358C C358C C358C C358C N355C N355C N355C N355C N355CE N358C N358C N358C N358C N358CE C355C C355C C355C C355C C355C C358C C358C C358C C358C C358C C358C N N N P A G G G G G G E P , , N N 79 70M2550.L 46 70M2580.L 46 70M2650.L 46 70M2750.L 46 70M2780.L L L L L L L L L N 21-23, N , L L L L 20 71M M M M M M M M M E E lum, Inc.

91 Page no N 21, N 21, N01 21, N N , , , L L L A.L E A A E M M A A A A A A A A A , Z Z M M M A A E A A A A A A A A A A A6000, A , 23, 57 I OLDER 79 D-2mm 85 D-2.5mm 85 D-5mm 81, 85 D-8mm 85 D-10mm 85 D-10 x 2mm 85 FX M01.Z05.D2 R 85 M01.Z05.D3 L 85 M01.Z08.03 L 85 M01.Z10.02 R 85 M01.Z10.03 L 85 M01.Z20.02 R 85 M01.Z35.02 R 85 M M M M30..UM 83 M M M31.Z M31.Z M *US 82 M US 84 M *US 82 M *50 82 M *US 82 MZA MZA MZA MZE MZK.0S 83 MZK MZK.880S 83 MZL.1250.US 84 MZM MZM MZM MZM MZM MZR.5300.US 84 MZS MZS MZS MZW MZV POZI I #2x1 79 POZI I #2x2 79 POZI DRIVER 79 SJ VP-5 85 ZME Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 89

92

93 Why choose lum lum, Inc. is a leading manufacturer of functional hardware for the kitchen cabinet and commercial casework industries specializing in lift systems, concealed hinges and drawer runner systems. Virtually all of the hardware needed to assemble and make cabinets functional is available within the wide range of quality lum products. lum supports the U.S. market with a network of more than 150 dependable distributors, 40+ knowledgeable lum sales representatives and an experienced customer service department. Commitment to manufacturing in the U.S. lum manufactures many of its products in our 450,000 sq ft manufacturing, logistics and warehouse facility located in Stanley, North Carolina. Manufacturing closer to the customer allows lum to react quickly to changing customer needs including unexpected surges in demand. Customer pickups and deliveries can be timed to better match their production schedules. lum is committed to manufacturing in the U.S. for the U.S. market. Product development at lum considers all of the various customers who will come in contact with our products. With this Global Customer enefits philosophy we strive to create advantages for all users. lum, Inc. is ISO 9001 certified which means that you are assured of consistent quality in every lum product. What s more they exceed the requirements of ANSI/ MA standards for cycle life, static load and self-closing performance.

94 Please visit blum.com for information on other lum products LI.NG lum, Inc. Printed in the USA lum, Inc Old Plank Rd. Stanley, NC blum.com

95 Premium concealed hinges Premium concealed hinges CLIP top and COMPAC hinges with integrated LUMOION blum.com

96 Elegant design and superior function Get to know the advantages of integrated LUMOION. Discover the possibilities of CLIP top LUMOION and COMPAC LUMOION hinges. Inspire your customers. Perfecting motion for doors, for the lifetime of the cabinet. Contents 2 LUMOION soft close 4 CLIP top LUMOION hinges 6 General specifications 16 Angled hinge program 26 CLIP top 155 hinges 29 CLIP mounting plates 33 CLIP top LUMOION hinge accessories 34 COMPAC LUMOION hinges 36 General specifications 42 COMPAC LUMOION hinge accessories 43 Assembly aids 52 Part number index

97 Quick reference inge cup centerpoint door 9.5 C Ø35 mm Conversion chart inch 1 1 / Ø / / C = Cup centerpoint /16" 27/32" 7/8" 15/16" 31/32" 1" = ore distance inges per door Cabinet height 100" 80" 60" 40" 20" inges required per door <15 lb lb lb lb his chart can serve as a guide for determining the number of hinges per door. Note that door weight can also determine the number of hinges required. NOE: he distance between the top and bottom hinges must be greater than the width of the door 3 1 / / / / / / / / / / / / / / / / inge abbreviation key S 16 5 / / / * 66.5 overlay = oring distance = Plate height OL = Door overlay P = Door protrusion R = Reveal S = Side arm protrusion = Door thickness W = Side panel width FD = Fixed distance P / / / / / / / / / Fixed distance (FD) he distance that the cup overlays the cabinet side panel when a hinge is attached to a 0 mm mounting plate. his is used to calculate hinge overlay with the formula X + minus = OL (Fixed distance + boring distance minus plate height = overlay)

98 LUMOION inside he elegant design of CLIP top LUMOION creates a sleek, sophisticated look while remaining easy to install and adjust LUMOION deactivation option he LUMOION function can easily be deactivated on one of the hinges, giving small or light doors the same high quality of motion. CLIP top LUMOION or COMPAC LUMOION hinges allow you to simply slide the switch on the hinge, close the door once and deactivation is complete. his creates a quicker, but still silent, close. LUMOION can be reactivated in the same way.

99 Innovative technology concentrated into a small space Silent and effortless closing Silent and effortless, that s how cabinet doors close with LUMOION. ecause the LUMOION mechanism is now integrated into the hinge cup, the same quiet close is achieved with a more discreet hinge. he braking action increases with the force of the door allowing it to close softly. his technology enables LUMOION to adjust itself automatically to each door size, weight and closing speed. Additionally, the integrated overload safety feature protects the LUMOION system from damage through abuse.

100 LUMOION inside > inge planning tools lum has downloadable Excel spreadsheets that help determine the hinge that is right for your application. Planning tools are easily accessible on our website at blum.com/planning 4 20 lum, Inc.

101 CLIP top LUMOION hinges Elegant design, Superior function Silent and effortless, that s how cabinet doors close with CLIP top LUMOION hinges regardless of the weight or closing speed. he LUMOION soft close mechanism is integrated in the hinge cup, and continues to provide the quality of motion you have come to expect from lum. With CLIP top LUMOION, you can now use thicker doors depending on the application. he new geometry ensures that the door does not make contact with the cabinet face even with smaller door gaps. CLIP CLIP top CLIP top LUMOION he tried and tested CLIP mechanism offers simple, tool-free hinge assembly. he industry standard for tool-free attachment since 85. Like other CLIP top hinges, CLIP top LUMOION enables easy threedimensional adjustment with lum s spiral tech depth adjustment. ecause the LUMOION function is now integrated into the hinge cup, additional assembly processes are no longer necessary after adjustment is complete. oring pattern he CLIP top LUMOION boring pattern for the hinge cup remains unchanged, however, a mm boring depth is required for all three holes (35 mm and 8 mm). INSERA he INSERA mechanism enables toolfree attachment of the hinge to the door. Press the insertion lever down and the dowels expand to hold the hinge in place. Mounting plates CLIP top LUMOION works with all current CLIP mounting plates so you can start using this new hinge right away with little change to production. 20 lum, Inc. 5

102 General specifications inge-to-door attachment Screw-on Use #6 wood screws Press-in Pre-attached Ø8 dowels installed with lum knock-in tool or MINIPRESS with an insertion ram EXPANDO Pre-attached expanding Ø8 mm dowels INSERA ool-free attachment with INSERA expanding Ø8 mm dowels Mounting plate-to-cabinet Screw-on EXPANDO Pre-attached expanding Ø5 mm dowels INSERA ool-free attachment with INSERA expanding Ø5 mm dowels 6 20 lum, Inc. Subject to technical modifications without notice

103 Adjustment LUMOION inside hree-dimensional adjustment Side adjustment Rotate front screw to increase or decrease door overlay (±2 mm) eight adjustment Rotate cam screw on mounting plate to adjust door position (±2 mm) Depth adjustment Rotate rear spiral tech cam screw to adjust door gap (+3 mm, -2 mm) On non-cam mounting plates, loosen screws, adjust door and retighten screws LUMOION deactivation Deactivation switch on hinge cup For small or light doors, the LUMOION can be deactivated on one of the hinges Door must be closed once for the deactivation to be complete. o reactivate, move switch back to original position. 1 2 emperature information CLIP top LUMOION is designed to be used at temperatures between 65 and 85 F. Lower or higher temperatures will not cause damage to the hinge, however they will affect the closing speed. Once the temperature returns to the suggested range the hinge will return to its optimal closing action. Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 7

104 CLIP top LUMOION 110 hinges 110 Features LUMOION integrated into the hinge cup Deactivation switch for small/light doors For door thicknesses up to 26 (1") Overload safety feature Compatible with existing CLIP mounting plates and hinge arm cover caps Minimum reveal table = boring distance = door thickness For thickness greater than 26 trial app. recommended Overlay Partial/twin overlay Inset Frame Frame Frame = 9 Panel * 66.5 W overlay Panel 66.5 NOE: Application requires a half-cranked hinge and mounting plate Panel 66.5 * W overlay 68 * = 0 14 min. reveal 66.5 * overlay * reveal * reveal *All 35 mm and 8 mm holes must be a minimum of mm deep Overlay P S Overlay P S fixed distance = boring distance = Reveal W P S fixed distance = boring distance = NOE: 4.5 plate is only for use in frame cabinets, 9 plate is only for panel cabinets = boring distance Straight-arm Screw-on Press-in EXPANDO INSERA Self close E alf-cranked Screw-on Press-in INSERA Self close Reveal P S fixed distance: 0 = -7 = boring distance 9 = 1.5 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width Full-cranked Screw-on Press-in INSERA Self close lum, Inc. Subject to technical modifications without notice

105 CLIP top LUMOION hinges 110 Features LUMOION integrated into the hinge cup Deactivation switch for small/light doors For door thicknesses up to 26 (1") Overload safety feature For door overlays up to 22 mm Compatible with existing CLIP mounting plates and hinge arm cover caps Minimum reveal table = boring distance = door thickness For thickness greater than 26 trial app. recommended Overlay Partial/twin overlay uilding both frame and panel cabinets Frame Panel W Frame * overlay * 66.5 overlay hinge (7335XX) plate ( ) 4.5 (1/2") Panel W Panel W Panel 0 same boring distance 66.5 * overlay *All 35 mm and 8 mm holes must be a minimum of mm deep Overlay P S Overlay P S fixed distance = boring distance = fixed distance = boring distance = NOE: 4.5 plate is only for use in frame cabinets, 9 plate is only for panel cabinets Reveal W P S 9 * 66.5 reveal = boring distance 29 hinge (7335XX) plate (any 0 mm plate) (11/16") he most common overlays for frame and panel cabinets can be achieved by using the same machine setting for hinge cup boring. ore all doors at 4.5 mm to achieve: (1/2") overlay on frame cabinets 17.5 (11/16") overlay on panel cabinets Advantages: One machine setting for boring all doors Same hinge used for both applications Straight-arm Self close Straight-arm Self close Abbreviations Screw-on Screw-on = Plate height Press-in EXPANDO E Press-in EXPANDO E P = Door protrusion S = Side arm protrusion INSERA INSERA W = Side panel width Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 9

106 Door thickness dimensions for 110 and hinges 110 New geometry for thick door applications Minimum reveals increase with door thickness. he following applications show common examples of necessary reveal and door gap for each door thickness. he factory setting for the door gap (distance between the back of door and front of side panel/frame) is 1.5 mm. For full opening angle without contacting the side panel or frame, the gap behind the door and the minimum reveal must be adjusted according to the table below. NOE: All dimensions based on 1 mm door radius Frame application Panel application minimum gap 1 rad (1/32") minimum gap 1 rad (1/32") minimum reveal minimum reveal 3/4" thick door 7/8" thick door 1" thick door Minimum reveal ore Minimum gap behind door Minimum reveal ore Minimum gap behind door Minimum reveal ore Minimum gap behind door** * *4.5 mm bore distance for use with hinges, reference page 9 **Factory setting is 1.5, may require adjustment * * lum, Inc. Subject to technical modifications without notice

107 CLIP top LUMOION 95 thick door hinges 95 Features LUMOION integrated into the hinge cup Deactivation switch for small/light doors For door thicknesses up to 30 (1-3/16") Overload safety feature Compatible with existing CLIP mounting plates and hinge arm cover caps Minimum reveal table = boring distance = door thickness For thickness greater than 30 trial app. recommended Overlay Partial/twin overlay Inset Frame Frame Frame = 9 Panel * 66 W overlay Panel * 66 W overlay NOE: Use a half-cranked hinge and mounting plate for this application Panel 67.5 * = 0 14 min. reveal 66 * overlay * 66 reveal 67.5 * reveal *All 35 mm and 8 mm holes must be a minimum of mm deep Overlay P S Overlay P S fixed distance = boring distance = fixed distance = boring distance = 11 NOE: 4.5 plate is only for use in frame cabinets, 9 plate is only for panel cabinets Reveal W P S = boring distance Reveal P S fixed distance: 0 = -7 = boring distance 9 = 1.5 Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width Straight-arm Self close alf-cranked Self close Full-cranked Self close Screw-on Screw-on Screw-on Press-in INSERA Press-in INSERA Press-in INSERA Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 11

108 CLIP top LUMOION 95 narrow aluminum door hinges 95 Features LUMOION integrated into the hinge cup Deactivation switch for small/light doors For door thicknesses up to 22 (7/8") Overload safety feature Compatible with existing CLIP mounting plates and hinge arm cover caps Minimum reveal table door frame width = door thickness For thickness greater than 22 trial app. recommended Overlay Partial/twin overlay Installation Frame Frame W Attach cup adapter to the hinge and insert into machined openings door frame width overlay door frame width overlay Attach using aluminum screws provided with hinges ( ) Panel Panel W W Aluminum door preparation door frame width overlay door frame width reveal Ø6 Overlay P S = fixed NOE: 4.5 plate is only for use in frame cabinets, 9 plate is only for panel cabinets Straight-arm Screw-on Self close 71950A Overlay P S = fixed Reveal W P S = fixed Straight-arm Self close Screw-on 71950A Abbreviations = Plate height P = Door protrusion S = Side arm protrusion W = Side panel width lum, Inc. Subject to technical modifications without notice

109 CLIP top LUMOION 95 inset blind corner hinges 95 Features LUMOION integrated into the hinge cup Deactivation switch for small/light doors For door thicknesses up to 24 (15/16") Overload safety feature oring distance range 3 mm to 7 mm Compatible with existing CLIP mounting plates and hinge arm cover caps Minimum reveal table = boring distance = door thickness For thickness greater than 24 trial app. recommended Flush door applications Offset door applications Adjustments and clearance adjust gap adjust reveal reveal reveal ack of door is flush with stationary panel Stationary panel spaced out thickness of door bumper 70 min Stationary panel mounted to cabinet side, top and bottom 70 min S * reveal * +/-2 +/-2.5 reveal 33.5 *All 35 mm and 8 mm holes must be a minimum of mm deep Reveal P S = boring distance Reveal P S = boring distance Abbreviations = Plate height P = Door protrusion S = Side arm protrusion Inset blind corner Self close Inset blind corner Self close Screw-on Screw-on Press-in Press-in INSERA INSERA Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc.

110 CLIP top LUMOION 95 overlay blind corner hinge 95 Features LUMOION integrated into the hinge cup Deactivation switch for small/light doors For door thicknesses up to 24 (15/16") Overload safety feature oring distance range 3 mm to 7 mm Compatible with existing CLIP mounting plates and hinge arm cover caps Minimum reveal table = boring distance = door thickness For thickness greater than 24 trial app. recommended Overlay application Adjustments and clearances gap adjust overlay adjust overlay 86 minimum setback +/-2 gap +/-2.5 overlay D 92 FP S gap * stationary panel overlay FP P NOE: Door gap can be adjusted ± 2 mm *All 35 mm and 8 mm holes must be a minimum of mm deep Setback Overlay P D Gap S Abbreviations D = Depth FP = Front panel thickness = Plate height fixed P = Door protrusion distance = boring distance = 9 FP = front panel thickness S = Side arm protrusion NOE: Door overlay varies depending on the setback position of the mounting plate. Use the table to select the desired overlay and cross-reference to the plate setback and bore distance. NOE: Door gap varies depending on the thickness of the stationary panel and the height of the mounting plate. Use the table to cross-reference the plate height based on the front panel thickness and door gap. Overlay blind corner Press-in Self close lum, Inc. Subject to technical modifications without notice

111 CLIP top LUMOION 110 diagonal hinge 110 Features LUMOION integrated into the hinge cup Deactivation switch for small/light doors Overload safety feature Compatible with existing CLIP mounting plates and hinge arm cover caps For thickness greater than trial app. recommended Overlay application Inside corner Calculating door width 45 o mitered panel overlay straight side panel Step 1. Using the boring distance () determined in the reveal table, cross-reference to find the side gap distance (Y) in the table below. Step 2. Using the following formula to find the door width. Door width = interior width minus (Y x 2). reveal Example: interior width = 400 mm, side gap (Y) = 4.5 mm. 391 = 400 minus (4.5 x 2) Y overlay reveal 1.5 Y interior width door width reveal * * *All 35 mm and 8 mm holes must be a minimum of mm deep Overlay Reveal = boring distance = boring distance NOE: Reveal based on (3/4") side panel Y = side gap = boring distance NOE: Calculations based on (3/4") door thickness Diagonal 45 hinge Self close Diagonal 45 hinge Self close Abbreviations INSERA INSERA = Plate height Y = Side gap Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 15

112 CLIP top LUMOION angled hinge program CLIP top LUMOION hinges from +45 to -45 Angled hinges provide a tremendous array of possibilities for the cabinet design professional. Specifically designed for panel (frameless) cabinets, the system accommodates cabinet front angles from -45 to +45, in 5 increments. his is achieved by combining any of ten angled hinges, or three standard hinges with a wedge spacer and any of five standard CLIP mounting plates. Step 1. On page 18, the angle-to-style cross-reference provides an overview of all the angled hinge applications available to assist with your specific application. Step 2. Once the cabinet front angle is determined, select the row for that angle from the first column. here are five different possibilities for positive angles and two for negative angles. All CLIP top LUMOION hinges feature "Spiral ech" depth adjustment which eliminates loosening and retightening the adjustment screws. Also, all CLIP top LUMOION angled hinges are INSERA for tool free hinge-to-door attachment. Step 3. Cross-reference the angle to the style to find the hinge/plate/wedge combination and the specification number. Specifications on pages to 25 are in numerical order and show all the details. 16

113 CLIP top LUMOION angled hinges Positive angled hinges II* III* I* II* III* *hese angled hinges are marked I, II, or III on the hinge arm for differentiation (see photo) Negative angled hinges hick door hinges used in angled applications 95 straight-arm half-cranked full-cranked Wedge spacers for positive and negative angles 2 mm thickness 4 mm thickness 5 mm thickness 7 mm thickness A A A A5070 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 17

114 Angle-to-style cross-reference LUMOION inside he chart on this page shows the hinge, plate and wedge (or spacer) needed for each angled application. he legend below shows the order of the part numbers. NOE: All 35 mm and 8 mm holes must be a minimum of mm deep Application number hinge CLIP top LUMOION hinge Part number plate CLIP mounting plate Part number wedge/spacer may or may not be required Part number wedge plate hinge front angle Positive angles Negative angles maximum overlay partial overlay corner merge inset door mitered corner maximum overlay inset door A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A lum, Inc. Subject to technical modifications without notice

115 Maximum overlay specifications Positive angle applications minimum 20 minimum =5 OL= =5 OL= =5 OL= A A minimum 20 minimum =5 OL= A A minimum 25 minimum =5 OL= =5 OL= =5 OL=16 40 =5 OL=16 45 =5 OL= A A Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc.

116 Partial overlay specifications Positive angle applications minimum minimum =5 OL=15.5 =5 OL=16 15 =5 OL= A A minimum =5 OL= =5 OL= =5 OL= A minimum minimum =5 OL= =5 OL= =5 OL= A A lum, Inc. Subject to technical modifications without notice

117 Corner merge specifications Positive angle applications minimum 25 minimum 20 minimum = = = A A A minimum =5 25 =5 30 = A minimum =5 45 = A Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 21

118 Inset door specifications Positive angle applications minimum 20 minimum 20 minimum R= R= = = A A A R= R= = R=1 R=1 25 =5 25 =5 30 = minimum minimum R=1 =5 40 R=1 =5 45 R=2 = A A lum, Inc. Subject to technical modifications without notice

119 Mitered corner specifications Positive angle applications Positive angle applications NOE: Miter door 65 Miter side 40 Radius edges to fit rial application recommended 35.5 minimum R=1 = A NOE: Miter door 62 Miter side 48 Radius edges to fit rial application recommended NOE: Miter door 70 Miter side 45 Radius edges to fit rial application recommended NOE: Miter door 70 Miter side 50 Radius edges to fit rial application recommended minimum R=1 = A NOE: Miter door 70 Miter side 55 Radius edges to fit rial application recommended R=1 = R=1 =9.5 NOE: Miter door 70 Miter side 55 Radius edges to fit rial application recommended minimum R=1 =9 45 R=1.5 = A Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 23

120 Maximum overlay specifications Negative angle applications minimum 20 minimum =5 OL=10 14 =5 OL=15 =5 OL= A A minimum 20 minimum =5 OL=8.5 =5 OL=15 =5 OL= A A minimum 20 minimum =5 OL=9.5 =5 OL= =5 OL= A A lum, Inc. Subject to technical modifications without notice

121 =5 Inset door specifications Negative angle applications minimum 20 minimum R=1 = =6 R= =9 R= A A minimum 20 minimum R=2.5 R=2.5 =8 = A A R=2 hinge mounting plate spacer Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 25

122 CLIP top 155 zero protrusion hinges 155 Features Zero protrusion hinge For use in cabinets with interior roll-outs For door thicknesses up to 24 (15/16") Add-on LUMOION available Compatible with existing CLIP mounting plates Minimum reveal table = boring distance = door thickness For thickness greater than 24, please see page 27 Overlay Frame Door protrusion At 90 opening, using 0 mm plate, the door will have -2.3 mm protrusion regardless of boring distance. Use side adjustment to increase or decrease door protrusion overlay NOE: Use of 0 mm or 3 mm is recommended for zero protrusion Panel LUMOION for 155 hinges W X S inge X S 72.5 CLIP top 155 straight-arm CLIP top 155 half-cranked overlay inge cup dimensions LUMOION for 155 hinge 973A Overlay P S fixed distance = boring distance = 11 Straight-arm Screw-on Press-in INSERA Self close N N N01 / *47 Angle restriction clips *INSERA For use with 155 hinges only Gray nylon 110 restriction clip N 92 restriction clip N Abbreviations = Plate height P = Door protrusion S = Side arm protrusion = Door thickness W = Side panel width lum, Inc. Subject to technical modifications without notice

123 20 CLIP top 155 straight-arm special applications 155 Maximum door thickness Maximum door overlay = 0 = 0 34 max N N reveal = 23 max rial application recommended NOE: For thick door applications, you must bore at the specified boring distance listed in the chart below rial application recommended Minimum reveal = door thickness = boring distance *Minimum reveal is 1 mm on a 25 mm thick door when bored at 8 mm Mitered door with large overlay Overlay = boring distance hin facing added to door = 0 = N N = max 11.7 = rial application recommended rial application recommended NOE: hese applications can be achieved in face frame cabinets by blocking out behind the frame Straight-arm Self close Angle restriction clips Abbreviations Screw-on Press-in N N For use with 155 hinges only Gray nylon = Plate height P = Door protrusion INSERA N01 S = Side arm protrusion 110 restriction clip N = Door thickness 92 restriction clip N09 W = Side panel width Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 27

124 CLIP top 155 half-cranked special applications 155 Lip door hick lip door = 3 = N max = lip detail max = 3 lip detail 10 P = overlay rial application recommended rial application recommended wo-sided and four-sided mitered door LUMOION for 155 hinges = X S = inge X S CLIP top 155 straight-arm P = 7.2 CLIP top 155 half-cranked rial application recommended LUMOION for 155 hinge 973A7000 NOE: hese applications can be achieved in face frame cabinets by blocking out behind the frame alf-cranked Self close Angle restriction clips Abbreviations Screw-on INSERA N N01 For use with 155 hinges only Gray nylon = Plate height P = Door protrusion S = Side arm protrusion 110 restriction clip N W = Side panel width 92 restriction clip N lum, Inc. Subject to technical modifications without notice

125 CLIP mounting plates Standard one-piece wing mounting plates Wood screw Steel, nickel-plated Attached with #6 x 5/8" wood screws eight adjustment ±3 mm 32 * 0 plate height () 173L plate height () 173L60 System screw 11.5 Steel, nickel-plated Attached with pre-mounted Ø5 mm system screws ( E) eight adjustment ±3 mm 32 Ø5 * 0 plate height () 173L plate height () 173L80 EXPANDO 11.5 Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels ( ) eight adjustment ±2 mm Ø5 32 * 0 plate height () 174E EXPANDO (twin application) 7.5 Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels for twin application ( ) eight adjustment ±2 mm 32 Ø5 * 0 plate height () 174E610Z System screw 11.5 Zinc die-cast, nickel-plated Attached with pre-mounted Ø5 mm system screws ( E) eight adjustment ±3 mm *Add additional wood screw if used with wide angled hinges 32 * Ø5 0 plate height () 175L plate height () 175L80 9 plate height () 175L80 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 29

126 CLIP mounting plates Cam adjustable wing mounting plates Wood screw Steel, nickel-plated Attached with #6 x 5/8" wood screws Cam height adjustment ±2 mm 32 * 0 plate height () plate height () 170 System screw 11.5 Steel, nickel-plated Attached with #7 x 5/8" wood screws or Ø5 x mm system screws Cam height adjustment ±2 mm 32 Ø5 * 0 plate height () plate height () EXPANDO 11.5 Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels ( ) Cam height adjustment ±2 mm Ø5 32 * 0 plate height () E 3 plate height () 17470E EXPANDO (twin application) 7.5 Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels for twin application ( ) Cam height adjustment ±2 mm 32 Ø5 * 0 plate height () ZE INSERA 11.5 Steel (closing lever zinc die-cast, nickel-plated) ool-free assembly with INSERA self-anchoring feature Cam height adjustment ±2 mm Ø5 *Add additional wood screw if used with wide angled hinges 32 * 0 plate height () I 3 plate height () 17470I lum, Inc. Subject to technical modifications without notice

127 Standard two-piece wing mounting plates Wood screw Zinc die-cast, nickel-plated Attached with #6 x 5/8" wood screws eight adjustment ±2 mm * plate height () plate height () plate height () System screw Zinc die-cast, nickel-plated Attached with #7 x 5/8" wood screws or Ø5 x mm system screws eight adjustment ±2 mm Ø5 0 plate height () * 32 3 plate height () plate height () plate height () plate height () *Add additional wood screw if used with wide angled hinges Cam adjustable In-line mounting plates Wood screw Steel, nickel-plated Attached with #6 x 5/8" wood screws Cam height adjustment ±2 mm Use of mounting plate template recommended 0 plate height () Press-in * 11.5 Steel, nickel-plated Pre-attached with 10 mm dowels Cam height adjustment ±2 mm Use of insertion ram MZM.0053 required Ø plate height () EXPANDO 11.5 Steel, nickel-plated Attached with pre-mounted screws with EXPANDO dowels Cam height adjustment ±2 mm Use of mounting plate template recommended Ø plate height () E 3 plate height () 17730E Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 31

128 Face frame adapter plates Face frame adapter plates Cam adjustable center mount Cam adjustable off-center mount Center mount Off-center mount With flange NOE: Use of PLAEMAE recommended with all face frame adapter plates Steel, zinc die-cast and nickel-plated Attached with #7 x 3/4" wood screws Center mount 9.5 (3/8") Cam height adjustment ±2 mm not for use with INSERA hinges 0 plate height () plate height () plate height () plate height () Steel, zinc die-cast and nickel-plated Attached with #7 x 3/4" wood screws For use with INSERA hinge cups Off-center mount 12.5 (1/2") Cam height adjustment ±2 mm 0 plate height () Zinc die-cast, nickel-plated Attached with #7 x 3/4" wood screws Center mount 9.5 (3/8") eight adjustment ±2 mm 3 plate height () 175L Zinc die-cast, nickel-plated Attached with #7 x 3/4" wood screws Off-center mount 12.5 (1/2") eight adjustment ±2 mm 0 plate height () 175L plate height () 175L plate height () 175L Recommended when using 170 and zero protrusion hinges on face frame cabinets Zinc die-cast, nickel-plated Attached with #7 x 3/4" wood screws Off-center mount 12.5 (1/2") eight adjustment ±2 mm 0 plate height () 175L Inset face frame adapter russ head screw Zinc die-cast, nickel-plated Attached with #8 x 3/4" truss head screws Can be used with applied bead molding Cam height adjustment ±2 mm Use with half-cranked hinges only Wide angle hinges not recommended Use of PLAEMAE required for installation 9 plate height () lum, Inc. Subject to technical modifications without notice

129 CLIP top LUMOION hinge accessories a Angle restriction clip 1 Restricts opening angle to 86 For use with CLIP top LUMOION and CLIP top 110 and hinges Can be inserted/removed before or after the hinge has been installed 2 Angle restriction clip inge cup spacer 1.5 mm spacer for use under the hinge cup Use to retrofit existing doors with a cup depth less than mm inge cup cover cap For use with CLIP top LUMOION hinges. Suitable for screw-on, press-in and EXPANDO hinge cups Can also be used with CLIP top 110 and hinges inge cup spacer inge cup cover cap inge arm cover cap P 90M M2203 (lum logo) M nylon steel 110, 110 +, and 95 thick door hinges Straight-arm 90M With lum logo P Cranked-arm 94M hinges Wide angle hinges , blind corner and narrow aluminum door hinges Specialty hinges 90M Angled hinges Straight-arm 90M NOE: Custom logo cover caps are available in black/white nylon or in nickel-plated steel. Consult your lum representative for minimum quantities and lead times on custom logos. Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 33

130 LUMOION inside > inge planning tools lum has downloadable Excel spreadsheets that help determine the hinge that is right for your application. Planning tools are easily accessible on our website at blum.com/planning lum, Inc.

131 COMPAC LUMOION hinges A complete face frame program Since the 80s lum s COMPAC concealed hinge has proven itself as the high quality solution for face frame cabinets. he new LUMOION soft closing mechanism is integrated in the hinge cup, and continues to provide the quality of motion you have come to expect from lum hardware. COMPAC LUMOION hinges are available for most overlay face frame applications or door styles. 39C/38C series Full overlay hinges COMPAC LUMOION 39C full overlay hinges with a 110 opening angle and 1/2" cup depth and 38C full overlay hinges with a 107 opening angle and 7/16" cup depth (ideal for profile doors). 38N series Partial overlay hinges COMPAC LUMOION 38N partial overlay hinges with a 105 opening angle and 7/16" cup depth. 38 series Full overlay, face mount hinges COMPAC LUMOION 38 full overlay face mount hinges with a 107 opening angle and 7/16" cup depth. Overload safety feature his feature protects the hinge from damage if the door is slammed and maintains the LUMOION soft closing for the life of the hinge. Deactivation option he LUMOION function can be easily deactivated on one of the hinges, allowing small or light doors to close with the same high quality of motion. Interchangeable with COMPAC hinges COMPAC LUMOION hinges are interchangeable with current COMPAC hinges so no need to change existing setups or workflows. 20 lum, Inc. 35

132 General specifications LUMOION inside Screw-on Use #6 wood screws Press-in Pre-attached Ø8 dowels installed with lum knock-in tool or MINIPRESS with COMPAC insertion ram Mounting plate attachment 39C/38C series wraparound 38N series wraparound/edge mount 38 series face mount Minimum reveal inge cup centerpoint A minimum reveal per door is required to keep the door from binding and varies depending on door thickness. See minimum reveal table for each hinge. reveal inge cup centerpoint and MINIPRESS/ MINIDRILL setback position is 20.5 (/16") for COMPAC LUMOION hinges 3/4" Ø8 45 Ø door 3 (1/8") 20.5 (/16") NOE: Maximum door thickness 3/4" inges per door his chart can serve as a guide for determining the number of hinges per door. Note that door weight can also determine the number of hinges required. 100" hinges required per door cabinet height 80" 60" 40" lb lb lb 20" <15 lb NOE: he distance between the top and bottom hinges must be greater than the width of the door lum, Inc. Subject to technical modifications without notice

133 Adjustment Door adjustment LUMOION inside hree-dimensional adjustment Side adjustment Rotate the front cam screw to increase or decrease door overlay (± 1/16") eight adjustment Loosen installation screws to adjust door position (± 1/8"), then retighten Depth adjustment Rotate the rear cam screw to adjust door gap (+ 3/32", - 1/32") LUMOION deactivation Deactivation switch on the hinge cup For small or light doors, the LUMOION can be deactivated on one of the hinges. COMPAC LUMOION comes in the activated position, marked with a "I". he deactivated position is marked with a "0". Door must be closed once for the deactivation to be complete. o reactivate, move switch back to the original position "I". 1 2 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc.

134 COMPAC LUMOION 39C hinges for full overlay 110 Description LUMOION integrated into the hinge cup Deactivation switch for small/light doors Overload safety feature One-piece wraparound hinge 1/2" cup depth Minimum reveal sq. edge minimum reveal Features3/4" door = 7/32" based on square edge doors oring pattern Dimensions door cabinet 3 Ø8 3/4" 3/8" 5/16" 1-1/16" 9.5 Ø pilot hole 1/8" 1/2" 110 gap 3/16" factory setting, adjusts +3/32" -1/32" 3/4" 1/8" overlay NOE: Maximum door thickness 3/4" Adjustment deactivation switch Wraparound hinges cam depth adjustment height adjustment overlay screw-on 47 press-in 1" 39C C /4" 39C C /16" 39C C /8" 39C C /2" 39C C /16" 39C C cam side adjustment Installation screw russ head screw 834 NOE: COMPAC LUMOION comes in the activated position, marked with a "I" the deactivated position is marked with a "0" Accessories Angle restriction clip inge cup spacer *lank cover cap *See page 42 for additional cover cap options 38C C C lum, Inc. Subject to technical modifications without notice

135 COMPAC LUMOION 38C hinges for full overlay Features 107 Description LUMOION integrated into the hinge cup Deactivation switch for small/light doors Overload safety feature One-piece wraparound hinge 7/16" cup depth Minimum reveal sq. edge minimum reveal 3/4" door = 9/32" based on square edge doors oring pattern Dimensions 3 door Ø8 cabinet 3/4" 3/8" 5/16" 1-1/16" 9.5 Ø pilot hole 1/8" 7/16" 107 gap 3/16" factory setting, adjusts +3/32" -1/32" 3/4" 1/8" overlay NOE: Maximum door thickness 3/4" Adjustment deactivation switch Wraparound hinges cam depth adjustment height adjustment cam side adjustment Overlay Screw-on 47 Press-in 1-1/4" 38C C Installation screw russ head screw 834 NOE: COMPAC LUMOION comes in the activated position, marked with a "I" the deactivated position is marked with a "0" Accessories Angle restriction clip inge cup spacer *lank cover cap *See page 42 for additional cover cap options 38C C C3508 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 39

136 COMPAC LUMOION 38N hinges for partial overlay Features Minimum reveal 105 Description LUMOION integrated into the hinge cup Deactivation switch for small/light doors Overload safety feature One-piece wraparound hinge Edge mount available in 1/2" overlay 7/16" cup depth Minimum reveal sq. edge minimum reveal 3/4" door = 9/32" based on square edge doors oring pattern Dimensions door cabinet 3 Ø8 3/4" 3/8" 7/16" 7/16" 3/4" Ø /8" pilot hole 1/8" 105 gap 3/16" factory setting, adjusts +3/32" -1/32" overlay NOE: Maximum door thickness 3/4" Adjustment Wraparound and edge mount hinges deactivation switch wraparound edge mount cam depth adjustment height adjustment cam side adjustment overlay door protrusion screw-on 47 press-in 5/16" 5/16" 38N /8" 1/4" 38N N /2" 1/8" 38N N *1/2" 1/8" 38N355E08 38N358E08 5/8" 0 38N N /4" 0 38N N *Available as edge mount hinge Installation screw russ head screw 834 NOE: COMPAC LUMOION comes in the activated position, marked with a "I" the deactivated position is marked with a "0" Accessories Angle restriction clip inge cup spacer *lank cover cap *See page 42 for additional cover cap options 38C C N lum, Inc. Subject to technical modifications without notice

137 COMPAC LUMOION 38 hinges for face mount 107 Description LUMOION integrated into the hinge cup Deactivation switch for small/light doors Overload safety feature One-piece face mount hinge 7/16" cup depth Minimum reveal sq. edge Features minimum reveal 3/4" door = 9/32" based on square edge doors oring pattern Dimensions 3 door Ø8 cabinet face 11/32" min. 11/16" 7/16" 3/4" Ø /8" overlay pilot hole 5/64" 107 gap 3/16" factory setting, adjusts +3/32" -1/32" NOE: Maximum door thickness 3/4" Adjustment deactivation switch Face mount hinges height adjustment cam side adjustment height adjustment overlay screw-on 47 press-in 1-3/8" or greater 38355F F22 Installation screw Flat head wood screw 606N or 606P NOE: COMPAC LUMOION comes in the activated position, marked with an "I" the deactivated position is marked with a "0" Accessories Angle restriction clip inge cup spacer 38C C3559 Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 41

138 COMPAC LUMOION hinge accessories a inge arm cover caps Steel, nickel-plated cap Available blank or embossed (lum logo) Also available with printed custom logo (minimum order quantity applies) 39C/38C cover cap 38N cover cap 39C/38C blank cover cap 39C/38C lum logo embossed cover cap 39C/38C lum logo with black ink cover cap 38N blank cover cap 38N lum logo embossed cover cap 38C C3508.P 38C3508.L 38N N3508P Angle restriction clip Restricts opening angle of the COMPAC LUMOION to 86 Angle restriction clip must be inserted before the hinge has been attached to the face frame inge cup spacer 1/16" spacer for use under the hinge cup for thin or profile doors Distance spacer Steel spacer decreases door overlay in 1/32" increments Can be stacked to achieve desired overlay reduction hinge cup decrease overlay by adding spacers spacer overlay Angle restriction clip 38C inge cup spacer 38C3559 Distance spacer lum, Inc. Subject to technical modifications without notice

139 Assembly aids a Deep thread wood screw For attaching hinges and mounting plates Deep thread system screw Pilot bore Ø5 (3/16") hole #6 x 1/2", #2 Phillips 6062N #6 x 5/8", #2 Phillips 606N #6 x 5/8", #2 POZI 606P #6 x 3/4", #2 Phillips 6064N #7 x 5/8", #2 Phillips 707N #7 x 3/4", #2 Phillips 7074N #7 x 10 mm, #2 POZI G #7 x 11.5 mm, #2 POZI G #7 x mm, #2 POZI G #7 x 14.5 mm, #2 POZI G #7 x 20 mm, #2 POZI G #7 x 25 mm, #2 POZI G Pan head system screw Pilot bore Ø5 (3/16") hole #7 x 14.5 mm, #2 POZI E russ head screw For attaching hinge to face frame ype 17 #8 x 3/4", #2 Phillips 834 win application screw Pre-bored Ø5 (3/16") hole Ø8 millimeter dowels Square head dowel for attaching to hinges Round dowel for insertion into doors Ø5 Ø5 POZI DRIVER and bits A POZI screwdriver (different from Phillips) is the most crucial tool you can use to assure that full torque is applied to all lum mounting screws. POZI screws can be identified by the distinctive tick marks located in the center of the screw head recess. POZI Phillips tick marks #2 POZI DRIVER POZI DRIVER 1/4" Magnetic bit holder I OLDER #2 x 1" POZI bit insert POZI I #2X1 #2 x 1 POZI bit insert POZI I #2X (9/16") screw (25/32") sleeve (15/16") sleeve Ø8 mm round dowel Ø8 mm square dowel With flange Installation screw Installation screw Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 43

140 Assembly aids Machines MINIPRESS P Deluxe boring and insertion machine Front adjustable boring distance with digital counter Pneumatic hold-down clamps oring depth adjustment Ruler stops (qty 4) ool kit included Dust collection attachment Optional laser center line set Accepts new 8 or 9 spindle heads Single phase 220V power hree-phase 220V power M *US M *US MINIPRESS M 110V manual boring and insertion machine 110V power with molding plug (portable) Does not require pressurized air Ruler stops (qty 4) ool kit included Dust collection attachment Accepts new 8 or 9 spindle heads Single phase 110V power M *US MINIDRILL P Standard boring machine Front adjustable boring distance Ruler stops (qty 4) ool kit included Dust collection attachment Optional laser center line, digital counter and hold down clamps sets Accepts new 8 or 9 spindle heads Single phase 220V power M * lum, Inc. Subject to technical modifications without notice

141 a Machine accessories 9 spindle head 9 spindle head for use with MINIPRESS/MINIDRILL ores nine holes spaced 32 mm apart, parallel to the fence New feature quick-disconnect chucks Once aligned, does not require additional adjustment ores cabinet side panel for 32 mm system boring for lum mounting plates and runners Requires retrofit set for use with machines produced in 2009 or prior Includes: Ø3 mm allen wrench Distance spacer Drive pin Air hose 9 spindle head MZK.0S Chuck cover cap M spindle head 8 spindle head for use with MINIPRESS/MINIDRILL ores eight holes spaced 32 mm apart, perpendicular to the fence New feature quick-disconnect chucks Once aligned, does not require additional adjustment ores all MEAOX and ANDEMOX front fixing brackets and galleries ores cabinet side panels for all lum runner systems Requires retrofit set for use with machines produced in 2009 or earlier Includes: Ø3 mm allen wrench Distance spacer Drive pin Air hose 8 spindle head MZK.880S Chuck cover cap M30.29 Spindle head retrofit set 1 Required for attachment of 9 and 8 spindle heads to MINIPRESS/ MINIDRILL produced in 2009 and prior Previous boring heads MZK.1000.US and MZK.8000.US cannot be used with the retrofit set Set includes: Adapter ring and shield 2 Ø5 mm allen wrench 3 Mounting bolts (qty 4) 4 Alignment pins (qty 2) 5 Alignment template 6 mm fixed depth stop (qty 2) Spindle head retrofit set M30..UM Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 45

142 Assembly aids Work table for M51 machine Work table for M52 machine Work table for M53 machine Work table MZA.1000 Work table MZA.5200 Work table MZA.5300 Center ruler Extension ruler Extension ruler support Center ruler, 600 (2') M Extension ruler MZL.1250.US Extension ruler support MZV.2100 Ruler stop Small ruler stop Large ruler stop Left or right ruler stop Left or right ruler stop Symmetrical ruler stop Ruler stop MZS.3000 Small ruler stop MZS.2000 Large ruler stop MZS.1000 Fixed depth stop (1/2") fixed depth stop for use with M51N machines (-shaped) Fixed depth stop (1/2") fixed depth stop for use with M53. machines Digital counter set Fixed depth stop M Fixed depth stop M Digital counter set MZE.2110 old down clamp set Laser center point set reakaway clutch For use with MINIPRESS and MINIDRILL old down clamp set M US Laser center point set MZR.5300.US reakaway clutch MZK lum, Inc. Subject to technical modifications without notice

143 a Euro hinge insertion ram Can be used for inserting CLIP top LUMOION, CLIP top, and CLIP press-in hinges Euro hinge insertion ram Can be used for inserting lum wide angle press-in hinges NOE: Not for use with CLIP top LUMOION and CLIP top 95, CLIP 100, wide angle or specialty hinges #10 insertion ram MZM #18 insertion ram MZM.0018 Euro hinge insertion ram Can be used for inserting most lum press-in Euro hinges COMPAC hinge insertion ram Can be used for inserting all lum COMPAC press-in hinges Mounting plate insertion Ram MINIPRESS insertion ram for press-in, in-line mounting plate NOE: Not for use with 170 and 155 wide angle hinges #40 insertion ram MZM.0040 #47 insertion ram MZM.0047 #53 insertion ram MZM.0053 Machine drill bits Ø5 mm drill bit (right handed) M01.Z05.D2 R Ø5 mm drill bit (left handed) M01.Z05.D3 L Ø8 mm drill bit (left handed) M01.Z08.03 L Ø10 mm drill bit (right handed) M01.Z10.02 R Ø10 mm drill bit (left handed) M01.Z10.03 L Ø5 mm Ø8 mm Ø10 mm Ø35 mm Ø20 mm drill bit (right handed) Ø35 mm with center point M01.Z20.02 R M01.Z35.02 R wist drill bits high speed steel VP-5 wist drill bit *Chuck for D-2mm *Used to pilot bore for screw-on hinges with MINIPRESS or MINIDRILL VP-5 centering bit VP-5 Ø2 mm left D-2mm Ø2.5 mm right D-2.5mm Ø5 mm right D-5mm Ø8 mm right D-8mm Ø10 mm right D-10mm Ø10 mm chuck for D-2 mm D-10 x 2mm Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 47

144 Assembly aids Knock-in tool Can be used to insert all lum press-in hinges Knock-in tool ZME.0710 ECODRILL 9.5 door C Simple device for boring lum hinge pattern Driven by electric/cordless drill (18v or higher) oring distance adjusts from 2 mm to 8 mm Clamps to various door thicknesses up to 40 mm Includes drill bits (pre-installed) and two orx bits Ø35 ECODRILL M Ø8 Accessories Replacement Ø35 mm bit M31.Z35.02 Replacement Ø8 mm bit M31.Z08.02 ool set MZW.00 ECOJIG holes are: 32mm apart, mm setback 32 Used to bore Ø5 mm holes for mounting plates that are mounted with system screws, EXPANDO dowels or INSERA Also can be used to pre-bore Ø5 mm holes for EXPANDO LUMOION adapters Ø5 mm stop collar included ECOJIG Universal individual template For pre-boring mounting plates Also used for marking and pre-boring cabinet profiles, LUMOION, IP-ON adapter plates and AVENOS locating pins Calibrated scale for accurate setting Universal individual template Mounting plate template in-line wing Use with CLIP mounting plates on overlay applications on panel cabinets For wing mounting plates ( mm setback) and in-line mounting plates (20 mm setback) Simple location of mounting plate screw positions Pilot bore Ø2.5 mm holes for wood screws Mounting plate template lum, Inc. Subject to technical modifications without notice

145 a QUICKFIX Drilling sleeve dimensions changed from 2.5 mm to 5 mm for drilling for in-line mounting plates Locates/matches positions of hinges and plates on cabinets and doors ransfers positions from door-to-cabinet and cabinet-to-door Adjustable stop for various door overlays For use with wing or in-line mounting plates QUICKFIX Accessories Additional CLIP template meter rail Ø5 mm drill bit D-5mm PLAEMAE adjustable M4 x 25 mm spacer screws included oring template for all lum face frame adapter plates Clamps to the frame with cam lever Adjustment knob accommodates frame thickness of 5/8" to 1" Spacer screws permit quick use without measuring Includes 2.5 mm pilot bit and drill bit extension PLAEMAE Dowelling fixture ool designed for attaching and removing dowels from hinges Mounts directly to work surface Doweling fixture INSERA boring template For boring Ø8 mm dowel holes after Ø35 mm hole is bored oring distance adjusts from 2 mm to 8 mm Also bores Ø5 mm holes for system screw mounting plates Includes drill stop collar to pilot bore Ø2.5 mm for screw-on plates INSERA boring template A LUMOION for doors boring template For pre-boring LUMOION adapters Ø10 mm drill bushing for panel edge boring Vertical guides for setting height Can be used to pre-bore for wing and in-line mounting plates Includes Ø10 mm, Ø5 mm and Ø2.5 mm stop collars LUMOION for doors boring template Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 49

146 50 Notes

147 51

148 Part number index Page no. 171A , 22, 24, A , 18, A , 21, A , , 23, 24, L L L L E610Z E E I ZE E I , 25, , 23, 25, , 20-22, , 22, L L L L L L L L E E , F F C C C3508.L 42 38C3508.P 42 38C C C N N3508P 42 38N355E N N N N N N N N N N358E C C C C C C C C C C C C N N N P A G G G G G G E P N N N N E A , 17-20, , 17, 18, 21, lum, Inc. Subject to technical modifications without notice

149 Page no , 17, 18, N 26, N 26, N01 26, N N E , 18, 24, , 18, 24, , 18, 24, , 17, 18, , 18, , 18, , 18, , 18, M M M A , 28 I OLDER 43 D-2mm 47 D-2.5mm 47 D-5mm 47, 49 D-8mm 47 D-10mm 47 D-10 x 2mm 47 M01.Z05.D2 R 47 M01.Z05.D3 L 47 M01.Z08.03 L 47 M01.Z10.02 R 47 M01.Z10.03 L 47 M01.Z20.02 R 47 M01.Z35.02 R 47 M M M M30..UM 45 M M M31.Z M31.Z M *US 44 M US 46 M *US 44 M *50 44 M *US 44 MZA MZA MZA MZE MZK.0S 45 MZK MZK.880S 45 MZL.1250.US 46 MZM MZM MZM MZM MZM MZR.5300.US 46 MZS MZS MZS MZV MZW POZI I #2x1 43 POZI I #2x2 43 POZI DRIVER 43 VP-5 47 ZME Dimensions in millimeters (inch equivalents as noted) 20 lum, Inc. 53

150 lum, Inc. eadquarters, Stanley NC

151 Why choose lum lum, Inc. is a leading manufacturer of functional hardware for the kitchen cabinet and commercial casework industries specializing in lift systems, concealed hinges and drawer runner systems. Virtually all of the hardware needed to assemble and make cabinets functional is available within the wide range of quality lum products. lum supports the U.S. market with a network of more than 150 dependable distributors, 40+ knowledgeable lum sales representatives and an experienced customer service department. Commitment to manufacturing in the U.S. lum manufactures many of its products in our 450,000 sq ft manufacturing, logistics and warehouse facility located in Stanley, North Carolina. Manufacturing closer to the customer allows lum to react quickly to changing customer needs including unexpected surges in demand. Customer pickups and deliveries can be timed to better match their production schedules. lum is committed to manufacturing in the U.S. for the U.S. market. Product development at lum considers all of the various customers who will come in contact with our products. With this Global Customer enefits philosophy we strive to create advantages for all users. lum, Inc. is ISO 9001 certified which means that you are assured of consistent quality in every lum product. What s more they exceed the requirements of ANSI/ MA standards for cycle life, static load and self-closing performance.