Contents Rockers. A Series... B4 Process Sealed 0.4VA Logic Level Straight, Right Angle, & Vertical PC

Transcription

1 Contents Rockers Toggles Rockers Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons A Series... 4 Process Sealed 0.4VA Logic Level Straight, Right Angle, & Vertical PC CW Series A Power Level Solder Lug, Quick Connect, & Right Angle PC Snap-in Mount CWS Series Illuminated Neon; 9A Power Level Quick Connect; Snap-in Mount CWSC Series Illuminated LED; 9A Power Level Solder Lug/Quick Connect; Snap-in Mount G Series Process Sealed 0.4VA Logic Level Straight PC GW Series Ultra-Thin 0.4VA Logic Level Straight, Right Angle, & Vertical PC GW Series Illuminated Fully Illuminated Paddle 0.4VA Logic Level Straight, Right Angle, & Vertical PC JW Series Internationally Approved 10A & 16A Power Level Solder Lug; Snap-in-Mount JWS Series Illuminated & Nonilluminated Internationally Approved 6A & 10A Power Level Solder Lug; Snap-in-Mount LW Series Illuminated A Power Level Incandescent Dual Lamps Solder Lug; Snap-in Mount 2

2 Rockers Contents M Series Snap-in Mount 6A Power Level & 0.4VA Logic Level Solder Lug, Quick Connect, Straight PC, & Wirewrap M Series racketed PC Mount 6A Power Level & 0.4VA Logic Level Straight, Right Angle, & Vertical PC with racket M Series Flat Frame Mount 6A Power Level & 0.4VA Logic Level Solder Lug & Straight PC M2100 Series Illuminated A Power Level & 0.4VA Logic Level Solder Lug, Quick Connect, & PC Flat Frame & Snap-in Mount M2T Series Process Sealed 6A Power Level & 0.4VA Logic Level Straight, Right Angle, & Vertical PC MLW Series Illuminated A Power Level Incandescent, Neon, & LED Lamps Solder Lug; Snap-in Mount P Series Internationally Approved 10A Power Level Solder Lug, Straight PC, & Quick Connect; Flat Frame Mount SW Series A to 30A Medium & High Capacity Solder Lug & Screw Lug Screw Mount WR Series Environmentally Sealed 15A Power Level Solder Lug, Screw Lug, Wire Lead, & Quick Connect Snap-in Mount Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 3

3 Series A Process Sealed Subminiature Rockers Touch Tilt Rockers Toggles Slides Rotaries Programmable Illuminated P Pushbuttons Supplement Accessories Indicators Tactiles Keylocks General Specifications Electrical Capacity (Resistive Load) Logic Level: 0.4VA 28V AC/DC maximum (Applicable Range 0.1mA ~ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: 50 milliohms maximum Insulation Resistance: 500 megohms 500V DC Dielectric Strength: 500V AC minimum for 1 minute minimum Mechanical Life: 100,000 operations minimum for On-None-On & On-Off-On 50,000 operations minimum for other circuits Electrical Life: 50,000 operations minimum Nominal Operating Force: 2.73N (momentary); 1.84N (maintained) Contact Timing: Nonshorting (break-before-make) Angle of Throw: 26 Materials & Finishes Actuator or Toggle: Case Housing: Support racket: Movable Contact: Stationary Contacts: Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Installation Cap Installation Force: PC Processing Soldering: Cleaning: Standards & Certifications Nickel plated brass Glass fiber reinforced polyamide Tin plated phosphor bronze Phosphor bronze with gold plating rass with gold plating rass with gold plating 30 C through +85 C ( 22 F through +185 F) 90 ~ 95% humidity for C (104 F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 39.23N (8.82 lbf) maximum downward force on actuator Wave Soldering Recommended: See Profile A in Supplement section. Manual Soldering: See Profile in Supplement section. Automated cleaning. See Cleaning specifications in Supplement section. The A Series rockers have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. 4

4 Process Sealed Subminiature Rockers Series A Distinctive Characteristics Subminiature size saves space on PC boards. Specifically developed for logic-level applications. Totally sealed body construction prevents contact contamination and allows time- and moneysaving automated soldering and cleaning. Award-winning STC contact mechanism with benefits unavailable in conventional mechanisms: smoother, positive detent actuation, increased contact stability and unparalleled logic-level reliability. (Additional STC details in Terms & Acronyms; see Supplement section.) Molded-in, epoxy sealed or ultrasonically welded terminals lock out flux, solvents, and other contaminants. x (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing. Matching indicators available. Actual Size Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 5

5 Series A Process Sealed Subminiature Rockers Touch Tilt Rockers Toggles Slides Rotaries Programmable Illuminated P Pushbuttons Supplement Accessories Indicators Tactiles Keylocks A Poles 1 SPDT 2 DPDT SP3T Circuits 2 NE 3 5 NE () R () NE 8 () () 9 () S () * 4 * 6 () () * 7 () ( ) = Momentary * 3- circuits TYPICAL SWITCH ORDERING EXAMPLE 2 2 K H C P 1 H V V1 PC Terminals Straight Straight with racket DESCRIPTI FOR TYPICAL ORDERING EXAMPLE lack.260 (6.6mm) Wide Rocker DPDT -NE- Circuit K Actuators Snap Top for Rocker Code C A22KP-CA Straight with Inline racket (Single Pole only) Right Angle with racket Vertical with racket Vertical with Inline racket (Single Pole only) C K Snap Top Actuator Single PC Terminals Rockers.260 (6.6mm) Wide (K only) A C E F G H A Colors lack White Red Yellow Green lue Gray 6

6 Process Sealed Subminiature Rockers Series A Pole SP DP Model A12 A13 A15 A1R A18 A19 A1S A22 A23 A25 A2R A28 A29 A2S Rocker Position ( ) = Momentary Connected Terminals Throw & Schematics Up Center Down Up Center Down () () () () () () NE NE NE NE NE NE () () () () () () Connected Terminals & Schematics ACTUATORS Note: 2-3 OPEN 2-1 SPDT OPEN DPDT For 3 Throw (3-On) Pole Model Up Center Down SP A24 A26 A27 Slot () External Connection 2 (in) 5 1 (out) 3 4 (out) 6 (out) K POLES & CIRCUITS Slot External Connection 2 (in) 5 1 (out) 3 4 (out) 6 (out) Snap Top For Rocker AT469 () () External Connection 2 (in) 5 1 (out) 3 4 (out) 6 (out) (5.0) The SP3T model utilizes a double pole base. Terminal numbers are not actually on the switch. 3 External connections must be made during field installation. (2.5) (COM) External Connection (COM) 5 (out) Common (in) (out) (out) 4 External Conn Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 7

7 Series A Process Sealed Subminiature Rockers Touch Tilt Rockers Toggles Slides Rotaries Programmable Illuminated P Pushbuttons Supplement Accessories Indicators Tactiles Keylocks P H C Straight Typ (0.8).031 Antirotational Material: Polyamide Colors Available: A,, C, E, F, G, H Color Codes: Right Angle with racket (0.3).012 (0.7).028 (0.5).020 AT (6.6mm) Wide Rocker V PC TERMINALS Use of a support bracket is recommended to increase PC mounting strength and stability. (0.6) Dia Typ (8.8).346 (0.6) Dia Typ (8.8).346 Straight with racket (10.16).400 Vertical with racket (0.3).012 ROCKERS & COLORS Straight with Inline racket Single Pole only A C E F G lack White Red Yellow Green lue (6.6).259 (10.0).394 (12.9).508 (8.8).346 (0.6) Dia Typ (0.3) Typ.012 (0.7) Typ.028 (0.7).028 (0.6) Dia Typ (0.5) Typ.020 (12.9).508 (4.5).177 (8.8).346 (19.0).748 (13.4) TYPICAL SWITCH DIMENSIS P/N This Side (0.6) Dia. (0.8).031 (8.6).339 (3.1).122 Double Pole (1) (2) (3) (0.4).016 (8.8).346 (4) (5) (6) 1 V1 (8.2) (10.2) (2.54) (0.3) Typ.012 (10.16).400 (0.6) Dia Typ (0.7) Typ.028 (1.0).039 C L Vertical with Inline racket Single Pole only (0.3).012 (6.6).260 (0.6) Dia Typ (0.5) Typ.020 (0.7).028 (0.8) Dia Typ.031 (1.0).039 C L (20.1).790 H (7.9).310 Gray Straight PC A22KPCA-CA 8

8 Process Sealed Subminiature Rockers Series A ROCKER MOUNTING PRECAUTI Rocker switches with vertical and right angle terminals must be mounted so that extension of the PC board beyond the top of the switch housing does not interrupt rocker movement, in turn causing incomplete switching operation. The MAXIMUM limit of the PC board extension is.051 (1.3mm), as illustrated below. This precaution does not apply to the double pole switch with right angle terminals due to the extra width of the switch allowing the rocker to clear the PC board. Side View of Rocker Right Angle Mounting PC Single Pole Only (6.6).260 Interruption by end of PC (1.3).051 PC Side View of Rocker Vertical Mounting PC Single Pole and Double Pole 26 Interruption by end of PC (1.3).051 PC Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 9

9 Notes 10

10 Notes 11