Distinctive Characteristics

Transcription

1 Distinctive Characteristics Low Profile Pushbuttons Series UB Bright, full face, or spot illumination with red, amber, or green single-element LEDs (an integral part of the switch), plus square or rectangular models. Combination of PCB mountability and short body allows use in compact applications. Small behind panel dimension for snap-in mounting in tight spaces. Snap-acting contact mechanism provides sensitive actuation with audible feedback; quick-make, quick-break characteristic limits arcing and prolongs electrical life. Latchdown mechanism, independent of switching mechanism, gives visible and tactile indication of circuit status. Terminals are epoxy sealed to lock out flux, solvents, and other contaminants. Momentary and alternate action circuits available in the same space-saving body size. Nonilluminated models available and shown in Pushbutton section. Matching indicators available and shown in Indicator section. Actual Size ILWON ELECTEL. webmaster@ilwon.com. Phone (0) -09. Fax (0)-009

2 General Specifications Low Profile Pushbuttons Series UB Electrical Capacity (Resistive Load) Power Level (code W): /0V AC or 0V DC Logic Level (code G): 0.VA 8V AC/DC maximum Note: See Supplement Index (page Z) to find explanation of operating range. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: Materials & Finishes Housing/Bezel: Snap-in Frame: Movable Contactor: Movable Contacts: Stationary Contacts: Switch Terminals: Lamp Terminals: Base: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: 0 milliohms maximum for silver; 00 milliohms maximum for gold 00 megohms 00V DC,000V AC minimum between contacts for minute minimum;,00v AC minimum between contacts & case for minute minimum,000,000 operations minimum for momentary; 00,000 operations minimum for alternate action 0,000 operations minimum for silver; 00,000 operations minimum for silver with resistive load of V AC 00,000 operations minimum for gold Single Pole: 0 grams for & 9 grams for Double Pole: 0 grams for & grams for Break before make.7mm (.07") pretravel; 0.mm (.0") overtravel;.mm (.09") total Glass fiber reinforced polyamide (UL9V-0) Stainless steel Phosphor bronze Silver alloy or copper with gold plating Silver alloy or copper with gold plating Phosphor bronze with silver or gold plating Brass with silver plating Glass fiber reinforced liquid crystal polymer (UL9V-0) - C through +0 C (- F through + F) 90 ~ 9% humidity for 9 0 C (0 F) 0 ~ Hz with peak-to-peak amplitude of.mm traversing the frequency range & returning in minute; right angled directions for hours 0G (90m/s ) acceleration (tested in right angled directions, with shocks in each direction) Installation Cap Installation Force: 7.N (.70 lbf) maximum downward force on cap Soldering Time & Temperature: 0 C or 70 C Process Seal: Not available Standards & Certifications Flammability Standards: UL Recognized: CSA Certified: UL9V-0 housing/bezel of GFR polyamide & base of GFR liquid crystal polymer All single & double pole models recognized at /0V AC or 8V DC; UL File No. WOYR.E; add "/U" to end of part number to order UL mark on switch. All single & double pole models certified at /0V AC or 0V DC or 0.VA 8V AC/DC maximum; CSA File No ; add "/C" to end of part number to order CSA mark on switch. ILWON ELECTEL. webmaster@ilwon.com. Phone (0) -09. Fax (0)-009

3 TYPICAL SWITCH ORDERING EXAMPLE UB SK G 0 C CC POLES MOUNTING TYPES TERMINALS SPDT DPDT CIRCUITS ON (ON) ( ) = Momentary ON ON Alternate Action with Latchdown PCB Mounting SK RK * Snap-in Mounting KK NK with NBK Side Barriers * Standard with solder lug terminals. CONTACTS & RATINGS W Silver Rated /0V AC Gold Rated 0.VA max 8V AC/DC max 0 0 C D F Solder Lug (for Snap-in Mounting) Straight PC LEDS Bright LED Red Amber Green CAP TYPES & COLORS Full Face Illumination Cap Color Diffuser Color * J Clear Clear * J C Red White * B D Amber Red C F Green Amber D Green F * J & B can be combined with any color listed above. Following combinations for only: JJ, CJ, DJ, & FJ IMPORTANT: AB Spot Illuminated Black Cap/ White Window Switches are supplied without UL & CSA marking unless specified. Specific models & ratings noted on General Specifications page. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE UBSKG0C-CC Gold Contacts with 0.VA Rating with PCB Mounting Red, Bright LED and Red Cap with Red Diffuser SPDT ON-(ON) Circuit Straight PC Terminals ILWON ELECTEL. webmaster@ilwon.com. Phone (0) -09. Fax (0)-009

4 POLES & CIRCUITS Plunger Position ( ) = Momentary Connected Terminals Throw & Power/Lamp Schematics Pole Model Normal Down Normal Down Notes: Switch is marked with NC, NO,, L+ & L-. Lamp circuit is isolated and requires external power source. SP UB ON (ON) UB* ON ON - - SPDT NC NO L (+) L (-) DP UB ON (ON) UB* ON ON DPDT NC NO NC NO L (+) L (-) * When in latchdown position for the alternate circuit, cap position is.0mm (.09") above the housing. SHAPES & MOUNTING TYPES PCB Mounting SK Single Pole Double Pole RK Single Pole Double Pole (.08) (7.) (7.) Typ (0.).00 (0.).00 (0.).00 (0.).00 C L (.) Dia Typ.07 C L (.) Dia Typ.07 C L (.) Dia Typ.07 C L (.) Dia Typ.07 Snap-In Mounting (Solder Lug) KK with Built-in Bezel NK with Built-in Bezel NBK with Built-in Side Barriers (.) Sq.8 (.).8 (.).88 Snap-in Mounting with Solder Lug terminals is the standard combination. Panel Thickness:.0 ~.mm (.09 ~.") CONTACT MATERIALS & RATINGS W G Silver Contacts Power Level V AC & 0V AC Gold Contacts Logic Level 0.VA 8V AC/DC maximum See Supplement Index (page Z) for complete explanation of operating range. TERMINALS Solder Lug The.0" x.0" oblong hole accommodates two solid or stranded -gauge wires. (.).0 (.0).079 (0.8).0 Thk = (0.) (0.) (.0).97 Straight PC (0.).008 (.0).7 (.0).09 Thk = (0.) ILWON ELECTEL. webmaster@ilwon.com. Phone (0) -09. Fax (0)-009

5 LED COLORS & SPECIFICATIONS Electrical specifications are determined at a basic temperature of C. LED circuit is independent of switch operation. If the source voltage is greater than rated voltage, a ballast resistor is required. The ballast resistor calculation and more lamp detail are shown in the Supplement; see Supplement Index (page Z). Bright LED (+) (-) C D F Color Red Amber Green Unit LEDs are an integral part of the switch and not available separately. Forward Peak Current I FM 0 0 ma Continuous Forward Current I F ma Forward Voltage V F.8.0. V Reverse Peak Voltage V RM V Current Reduction Rate Above C I F ma/ C Ambient Temperature Range - C ~ +0 C CAP TYPES & COLOR BINATIONS Transparent Cap with Diffuser for Full Face Illumination J C Clear Red AT07 Cap Caps (.0).8 (.0) Sq J B Clear (for square only) White Diffusers AT07 Diffuser for AT07 Cap (0.) (0.) Sq.07 D F Amber Green AT7 Cap (.0) (7.0).9 (.0).8 C D F Red Amber AT8 Diffuser for AT7 Cap Green (.) (0.).0.07 (0.) Cap & Diffuser Material: Polycarbonate Cap Finish: Glossy Diffuser Finish: Textured Note: Both cap & diffuser colors must be selected. J & B can be combined with any color. Combinations JJ, CJ, DJ, & FJ are for only. Spot Illuminated Cap AB AT9 AT0 Black Cap with Translucent White Window for LED Display (.0).97 (.9).07 (.). (.0).97 (.9).07 (.). Material: Polycarbonate Finish: Matte (.0).8 (.0) Sq (.0) (7.0).9 (.0).8 ILWON ELECTEL. webmaster@ilwon.com. Phone (0) -09. Fax (0)-009

6 TYPICAL SWITCH DIMENSIONS PCB Mount (0.) UBSKG0C-CB (.0) Sq (.) Sq.00 (.) (.0).09 (0.0).9 Latchdown Position (0.) Typ Single pole models do not have terminals,, &. Nonilluminated models do not have lamp terminals. (.0) (.0) Typ PCB Mount (0.) UBRKG0D-DD (.0) (.).00 Snap-in Mount Built-in Bezel (7.0).9 (0.).800 (.) (.0).09 Single pole models do not have terminals,, &. Nonilluminated models do not have lamp terminals. (0.0).9 (.).0 (.0).7 Latchdown Position (0.) Typ (0.8) x (.) Typ.0 x.0. (7.) Typ.00 (.0) Typ (.0) Sq (7.8) Sq (0.0) (.0) Latchdown Position Single pole models do not have terminals,, &. Nonilluminated models do not have lamp terminals. Snap-in Mount Built-in Bezel (.) (.0).09 (.).0 (0.) Typ (0.8) x (.) Typ.0 x.0 (.0) Typ (.8). UBKKW0C-CB (.0) (7.8).70 (7.0).9 (.0).9 Latchdown Position Single pole models do not have terminals,, &. Nonilluminated models do not have lamp terminals. Snap-in Mount Built-in Side Barriers (.) (.0).09 (0.0).9 (.0).97 (0.) Typ (0.8) x (.) Typ.0 x.0. (7.) Typ.00 (.0).8.00 (.8)..00 (.0) Typ.079 UBNKW0F-FF (.0) (7.8).70 (7.0).9 (.0).9 (0.) Typ Single pole models do not have terminals,, &. Nonilluminated models do not have lamp terminals. ILWON ELECTEL. webmaster@ilwon.com. Phone (0) -09. Fax (0)-009 (.9). (8.).9 (.0).97. (7.) Typ.00 (.0).8.00 (.8)..00 (.0) Typ.079 UBNBKW0F-FB

7 OPTIONAL ACCESSORIES Spring Loaded Protective Guard for Snap-in Mounting of PCB Model AT7 Protective Guard/ Snap-in Frame Opens 80 Closes automatically (0.) (0.). (.). Cover: Clear Polycarbonate Base: Black Polyamide Coil Spring: Stainless steel (8.).7 (0.).80 (.0). (9.0). 80 (.). Recommended Panel Thickness:.0mm ~.mm (.09" ~.") (8.) Sq.77 Recommended Panel-to-PCB Range: 9.0mm ~.0mm (." ~.") AT7 (0.). (9.0) Min*. Protective Guard Panel (0.) Installation (9.0) ~ (.0). ~. (0.).80 (0.).80 (N) (N) = Number of switches * Minimum dimension allows opening of cover to 80. Install switch onto PC board.. Snap protective guard into panel.. Join the two assemblies. Switch PC Board Spring Loaded Protective Guard for Snap-in Model AT7 Protective Guard Opens 80 Closes automatically (0.) (0.). (7.).80 (7.9).70 (8.).7 (0.).80 Cap Height When Assembled (7.).9 (.).9 (7.9).70 (.) Sq.8 AT7 (0.) (0.). (9.0) Min*. Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel 80 (0.).80 (0.).80 (N) (N) = Number of switches * Minimum dimension allows opening of cover to 80 Recommended Panel Thickness:.0mm ~.7mm (.09" ~.0") ILWON ELECTEL. webmaster@ilwon.com. Phone (0) -09. Fax (0)-009

8 OPTIONAL ACCESSORIES Spring Loaded Protective Guard for Snap-in Mounting of PCB Model AT7 Protective Guard/ Snap-in Frame Opens 80 Closes automatically Cover: Clear Polycarbonate Base: Black Polyamide Coil Spring: Stainless steel (.).9 (0.) (0.). (.).99 (.).07 (.0). (9.0). 80 (0.).809 (.). Panel Thickness:.0mm ~.mm (.09" ~.") (8.).77 Recommended Panel-to-PCB Range: 9.0mm ~.0mm (." ~.") (9.0) ~ (.0). ~. (0.) AT7 (0.). (.).07 (.).07 (N) (9.0) Min*. Installation. Install switch onto PC board.. Snap protective guard into panel.. Join the two assemblies. Protective Guard Panel Switch PC Board (N) = Number of switches * Minimum dimension allows opening of cover to 80 Spring Loaded Protective Guard for Snap-in Model AT7 Protective Guard Opens 80 Closes automatically (0.) (0.). (7.).80 (7.9).70 (.).88 (.).99 (.).07 Cap Height When Assembled (7.).9 (0.).80 (.).99 (.).8 AT7 (0.). (9.0) Min*. Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel 80 (0.) (.).07 (N) = Number of switches (.).07 (N) * Minimum dimension allows opening of cover to 80 Recommended Panel Thickness:.0mm ~.7mm (.09" ~.0") ILWON ELECTEL. webmaster@ilwon.com. Phone (0) -09. Fax (0)-009

9 OPTIONAL ACCESSORIES Splash Covers AT00 Not for use with barrier type models. AT0 (.0) Sq.9 (.).0 (.).0 (.0).9 Cap Height When Assembled (7.).87 (.) (.0) Sq.9 (.7).89 (0.).89 PVC with polyethylene gasket (PVC loses pliability below 0 C ( F).) Panel Thickness.0mm ~.mm (.09" ~ ") LEGENDS General information and basic specifications are presented here for customers who want to do their own legends. Suggested Printable Area for UB Lens & Film Insert Cap UP Lens Shaded areas are printable areas. Lens (0.8). (.0) Cap Lens (0.8) Sq. (.0) Sq (.8).09 (7.0).9.00 (0.) R (0.) R RUN Film Insert Film Insert (8.78). (0.).0 Diffuser (8.78) Sq. (0.) Sq (.78). (.).0.00 Recommended Print Methods: Screen Print on Lens or Film Insert; Pad Print on Lens. Epoxy based ink is recommended. Film Insert: Clear Polyester mil max. thickness LEGEND PACKET UP. To order caps with legends contact the factory and request the UB/UB Legend Packet.. Once you determine your desired legend, fill out the ordering work sheet included in the packet.. Return the completed work sheet to receive a quotation. ILWON ELECTEL. webmaster@ilwon.com. Phone (0) -09. Fax (0)-009