PrepKing. PrepKing

Transcription

1 PrepKing Number: Passing Score: 790 Time Limit: 120 min File Version: PrepKing

2 Exam A QUESTION 1 After connecting to a codec via WebGUI, you are prompted for a username and password. Which username password combination is codec by default? A. Cisco, Cisco B. admin, Cisco C. Cisco, Cisco D. admin, cisco Correct Answer: D /Reference: QUESTION 2 Which statement is correct when discussing the Cisco TelePresence System 1300? A. The system is designed to support meetings of six to eight participants B. The system features three 65-inch screens, three cameras, microphones, and speakers C. Voice-enabled switching is performed by the codec to select the active speaker in the room and capture the video for the remote side D. The power and Ethernet outlets must be positioned directly behind the unit /Reference: QUESTION 3 When using Auto-Collaborate. What two actions need to be done to display the laptop content after connecting the cable? (Choose two) A. Press the Auto-Collaborate softkey B. Initiate Auto-Collaborate on the codec's GUI C. Set the laptop resolution to 1024x768 D. Set your laptop resolution to 1024x720 E. Use function key on the laptop to send signal to external display Correct Answer: AE /Reference: QUESTION 4

3 During your RRA assessment of a potential Cisco TelePresence System 1300 room you notice. The HVAC diffuser has noticeable noise (measured at 48dB) which sounds like rushing air. What three recommendations should be made to the customer? (Choose three) A. The customer should turn the fan level down on the HVAC system to insure the fan noise is minimized in the Cisco TelePresence room B. The customer should contact an HVAC specialist to review and recommend an appropriate solution C. The customer should not worry about the HVAC fan noise because the Cisco TelePresence System uses a noise suppression algorithm designed to identify HVAC fan noise and minimize those frequencies D. The customer should replace the diffusers with a diffuser that is rated with a noise criterion of 10 or greater E. The customer should replace the ducting directly above the room with acoustically treated ducting to remove the sound of rushing airflow Correct Answer: ADE /Reference: QUESTION 5 In the Cisco TelePresence administration WebGUI, the camera Auto Adjust can be used to check which setting? A. life size B. zoom and focus C. white color balance D. HDMI input threshold /Reference: QUESTION 6 What is the leveling process for the Cisco TelePresence System 1000 frame? A. With only one display, there is no need to level the frame before attaching it to the wall B. Attach the frame to the wall and level the frame by raising or lowering the feet. C. Place a level on the middle and upper crossbars and adjust the feet as necessary to ensure that the frame is horizontally level D. Place a level on the side of the frame and adjust the feet as necessary to ensure that the frame is vertically level

4 /Reference: QUESTION 7 Refer to the exhibit. Identify the port number where the A/V expansion box should connect A. B. C. D. E. F. G. H. I Correct Answer: H /Reference: QUESTION 8 Which statement is correct when tuning the cameras by using the WebGUI of the Cisco TelePresence codec?

5 A. If there is a noticeable flicker on the screen, the 60 Hz Flicker Reduction button will eliminate the flicker and improve the image quality B. If the user is 1 2 to 1 5 meters (four to five feet) away from the display, click the 4 feet radio button for the Focus Distinct radio choice. if the user is farther than 1 5 meters (five feet) away, click the 6 feet choice C. It the room uses outside lighting, click the Disable r.idm button for the Camera Auto Brightness and Camera Auto Color Balance choices D. Auto Color Balance can produce the best results when the colors of the walls in your room are white or gray /Reference: QUESTION 9 Which three statements are correct when tuning the camera on a Cisco TelePresence System? (Choose three.) A. Target placement should match the green and red boxes on the screen, respectively B. Place the large target three feet behind the small target. C. Place the large target five feet behind the small target D. Tune the camera so that the red and green bars line up as closely as possible E. Perform auto-adjust to optimize focus and sharpness Correct Answer: ACD /Reference: QUESTION 10 Which two statements are correct when calibrating the Cisco Telepresence cameras? (Choose two) A. If the room uses fixed artificial lighting, click the Disable radio button for the Camera Auto Brightness and Camera Auto Color Balance B. If the Auto Adjust test to automatically adjust lighting and color balance fails, you may need to add more light C. If the room uses fixed artificial lighting, click the Enable radio button for the Camera Auto Brightness and Camera Auto Color Balance D. If the room uses outside lighting, click the Disable radio button for the Camera Auto Brightness and Camera Auto Color Balance Correct Answer: AB /Reference: QUESTION 11 During your assessment of a potential Cisco Telepresence System 1300 room you notice. The ceiling is 8 feel (2,4meters) high and currently illuminated with recessed parabolic light fixtures. Which

6 lighting recommendation is the most appropriate? A. The Cisco Telepresence endpoint has a lighting facade which is designed to provide enough light for the participants face and torso, so no lighting changes are required B. The ceiling should be raised higher than 8 feet (2.4 meters) to accommodate appropriate light fixtures for use with Telepresence C. The existing fixtures are not ideal but are adequate for use with TelePresence D. The existing fixtures should be replaced with recessed indirect light textures E. No recommendation can be made until the lighting has been measured with a lux meter in the appropriate zones Correct Answer: D /Reference: QUESTION 12 Which is a design requirement for Cisco Telepresence room aesthetics? A. Every room should be identical. B. Maintain continuity in appearance among rooms C. Carpet patterns and textures match from room to room D. All rooms should be painted brown E. The only wall treatment should be paint /Reference: QUESTION 13 When using HFR codec in a multipoint call, what happens when an endpoint without HFR calls in? A. The entire call downgrades the data channel to 5 fps B. The entire call downgrades the data channel to 5 fps but when the endpoint without HFR codec drops, it automatically increases the data channel to 30 fps C. The endpoint without the HFR shares data at 5 fps and all the other endpoints share at 3D fps D. The call drops since there are different frame rates Correct Answer: A /Reference: QUESTION 14 Which option on the Cisco Telepresence System administration WebGUI allows selecting table type? A. Troubleshooting --> Hardware Setup --> Display B. Troubleshooting --> Hardware Setup -> Configuration

7 C. Troubleshooting -> Hardware Setup --> Camera D. Troubleshooting -> Hardware Setup -> Other Devices /Reference: QUESTION 15 What is the first step when preparing to attach the Cisco Telepresence System 1100 or Cisco Telepresence System 1300 mounting bracket to the wall? A. Attach the sliders on the bracket to the wall B. Level the bracket C. Find the center of the conference table D. Measure the correct width between the drill holes of the mounting bracket /Reference: QUESTION 16 Which two statements are correct when discussing the Cisco Telepresence codec software upgrade process? (Choose two) A. Cisco TelePresence codecs must have IP address information for the TFTP servers that the Cisco Unified Communications Manager use B. TFTP server information must be manually provided to the Cisco TelePresence codec when the 150 option in the DHCP scope for Cisco Unified Communications Manager is enabled C. Cisco TelePresence codecs use TFTP to download system images and configuration files D. To abort the upgrade, you can reboot the codec manually before the codec finishes downloading the software image E. The peripherals upgrade can take up to 60 minutes to complete During the upgrade, the display screens are blank Do not manually reboot the codec during the peripherals upgrade E /Reference: QUESTION 17 What is the default configuration for displaying presentations on a Cisco Telepresence System 1000? A. An external display for displaying presentations is part of the default configuration. B. Presentations are displayed as presentation-in-picture.

8 C. Presentations are displayed on an external display and include a presentation codec. D. A projector and screen are used to display presentations. /Reference: QUESTION 18 Which statement is correct when discussing the microphone placement for the Cisco Telepresence System 1100? A. The installation kit provides you with two microphones that must be installed B. You can install the second microphone on the opposite side of the table to provide full-table microphone coverage for audio-only conferences C. The second microphone should be installed 9 inches (23 cm) from the edge of the table that is closest to the plasma display D. Align the holes in the bottom of the microphone guide with the threaded holes in the microphone and secure them with the screws and washers provided /Reference: QUESTION 19 The customer decides to use static IP addressing for the codec. Which three parameters must be configured? (Choose three) A. IP address B. IP address subnet mask C. gateway IP address D. NTP server IP address E. DNS server IP address Correct Answer: ABC /Reference: QUESTION 20 What are the two choices for focal distance on a CTS-500? (Choose two) A. 3.5 feet B. 4 feet C. 6 feet D. 8 feet E. 8.5 feet

9 C /Reference: QUESTION 21 Which two statements describe the design goals for the Cisco Telepresence System? (Choose two) A. Creating a uniform feeling across all installations helps to create the illusion of participants being in the same room B. Cisco does not recommend colors so that customers can choose a palette that best complements their corporate standards, while creating an environment that is both warm and inviting C. Customers should use different colors in each of the Cisco Telepresence rooms to help identify the different locations D. Textures and adornments on the walls should not be similar to those of the walls in the other rooms E. Repeatability strengthens the feeling of a common, seamless environment, which enhances the overall experience Correct Answer: AE /Reference: QUESTION 22 Which two statements are correct when discussing light measurement recommendations for a Cisco Telepresence System 1100 room? (Choose two) A. Overall illumination should be measured with the light sensor pointed at the ceiling B. When measuring overall illumination in the room, the light range should be between 250 and 800 lux. C. Generally, shoulder lighting should be no more than 3 times greater than the overall illumination of the room D. Overall illumination of the room should never exceed 900 lux E. The overall illumination target with the auto features disabled is between 250 and 460 lux Correct Answer: AB /Reference: QUESTION 23 A Cisco Telepresence System 1000 is being installed into a room where the walls are constructed of drywall over metal studs. What is the correct mounting hardware for this type of installation? A. 5/16 x 5-inch wood screws B. 3/1B x 5-inch wood screws C. M6.0 x 80-mm hex head screws D. 1/4-20 Snap Toggler BB anchor

10 /Reference: QUESTION 24 Which would be considered the best environment to house a dedicated Cisco TelePresence system? A. a conference room in the corner of a building with the best view B. a conference room next to the elevator for easy accessibility C. a conference room along an interior corridor D. an open space in the demonstration area of a briefing center E. a large meeting room used for events /Reference: QUESTION 25 What are two Cisco recommendations when a customer has magnetic ballast installed in? A. Enable auto brightness and disable auto color balance. B. Enable auto brightness and auto color balance. C. Enable 50-Hz flicker reduction D. Enable focus distance to A feet E. Replace the light fixture with an electronics fixture E /Reference: QUESTION 26 When booting the Cisco TelePresence 500, how do you determine which IP address is used by the codec before connecting to the codec via WebGUI? A. The codec, uses as its default IP setting B. The IP address is displayed on the phone user interface C. The IP address is displayed during the hunt process on the plasma D. The codec uses as its default IP setting /Reference: QUESTION 27 When using the camera target on a Cisco TelePresence System 1300, how often do you need to repeat the

11 auto-adjust procedure before all cameras are calibrated? A. once B. twice C. three times D. four times /Reference: QUESTION 28 During your assessment of a potential Cisco TelePresence System 1100 room you notice - Walls and 4 are painted plasterboard (drywall) - Wall 3 is a heavy plate glass interior wall with a solid frosted finish What are two inherent concerns? (Choose two) A. Privacy is compromised because people will be able to see into the room through the glass wall B. Lighting from the adjacent room may illuminate a portion of this room and should be measured to see if remediation is required C. The glass wall will promote excessive reverberation between itself and the multiple plasma screens on the Cisco Telepresence endpoint. D. The glass wall will promote excessive reverberation between itself and wall 4 D /Reference: QUESTION 29 Which statement is correct when discussing the Cisco Telepresence System 500? A. Installation is easy with some required remediation and construction cost B. A power distribution unit provided with the system C. The system requires three AC outlets one tor the codec, one for the facade lighting, and one for the LCD display D. The system requires two AC outlets one for the codec and one for the LCD display Correct Answer: D /Reference: QUESTION 30

12 Which statement is correct when discussing the camera target placement for the Cisco Telepresence System 500? A. Do not set the easel and large target in the position that the user will occupy B. Use the distance measured from the camera to the head of the user to position the target If the distance is unknown, use 1.5 meters (5 feet) C. The user must be at least 8 feet (2,4 meters) away from the display D. Raise or lower the target so that the green rectangle that displays on the screen is at the approximate eye level of the user /Reference: QUESTION 31 When performing the Auto White Balance Adjustment on a Cisco Telepresence System, which three statements are correct? (Choose three) A. Lights must be set as they would be during a TelePresence meeting B. The RJ-45 cables must be unplugged from the Cameras not being configured to ensure that each camera is set up independency C. Ensure that no movement in the room might cross in front of the camera or create shadows on the target board D. Target boards should be set up on each table segment at the same time. The adjustment runs on all segments at the same time to capture the exact lighting for a consistent configuration E. The adjustment must be run on each segment and can be run only one segment at a time F. The adjustment needs to be run only on the center camera. The settings are duplicated on the left and right segments Correct Answer: ACE /Reference: QUESTION 32 During your assessment of a potential Cisco Telepresence System 1300 room you notice. - None of the insulated walls extend up to the structural deck above the suspended ceiling tiles - All adjacent rooms are conference rooms The customer makes it clear that their landlord prohibits wall construction in the open plenum space above the suspended ceiling. What are two appropriate recommendations? (Choose two) A. Recommend the customer doubles the layer of drywall below the plenum ceiling to achieve adequate isolation from adjacent room B. Recommend the customer installs white noise generator to mask the noise from adjacent rooms C. Recommend the customer installs added insulation above the suspended ceiling tiles D. Recommend the customer do nothing but be advised of possible noise issues with the adjacent rooms so that proper expectation is Correct Answer: AC

13 /Reference: QUESTION 33 Which side of the cabinet is the Cisco Telepresence System 1100 and 1300 codec inserted? A. right B. center C. left D. back and center Correct Answer: A /Reference: QUESTION 34 How many camera processors does the Cisco Telepresence System 1300 have? A. one B. two C. three D. four /Reference: QUESTION 35 How should directory number of the phone and the Cisco Telepresence endpoint be configured in the Cisco Unified CallManager? A. As a shared line where the codec and IP phone share the same directory number B. As a single line for the codec and a single line for the phone using the same directory number. C. As an overlay line using the same directory number D. As a single line for the phone and it only has a directory phone number. The codec uses the IP address of the phone Correct Answer: A /Reference: QUESTION 36 What are three requirements to tune the camera properly on a Cisco Telepresence System 1300? (Choose three)

14 A. The table configuration is completed by using the Cisco Telepresence System administration WebGUI hardware setup B. The table selection is completed in the Cisco Unified Communications Manager device configuration page C. The table edge where participants sit is six to ten feet away from the display D. The table must be perfectly centered and parallel to the Cisco TelePresence System E. The table edge where participants sit is optimal at ten feet away from the display Correct Answer: ACD /Reference: QUESTION 37 During the room assessment, how should you hold the light sensor when taking the majority of light measurements? A. Horizontally, so it gets the direct lighting from ceiling light fixtures B. Vertically, toward the displays to measure the light they put off C. Horizontally, toward any untreated windows to measure light coming in D. Vertically, so it is reading light as if it were hitting the participant's face. Correct Answer: D /Reference: QUESTION 38 What is the Cisco recommendation for power and Ethernet sources location before installing the Cisco Telepresence System 1300? A. directly behind at center B. to the right side, two feet from center C. to the left side, three feet from center D. either the left or right side, no less than four feet from center Correct Answer: D /Reference: QUESTION 39

15 Which statement is correct when discussing the Cisco Telepresence System 500? A. If the user is able to see any of the positioning LEDs while seated, then the user is out of camera view B. To view auto-collaboration presentations from the remote room, you must have a secondary LCD display C. The system must be placed in a position so that the participant is eight feet from the display D. If the user cannot see any of the positioning LEDs while seated, then the user is out of camera view Correct Answer: A /Reference: QUESTION 40 When calibrating the camera on a Cisco Telepresence System, which two settings are needed for Cisco Telepresence rooms with varying lighting conditions? (Choose two) A. Auto Adjust B. Auto Luminance C. Camera Auto Color D. Camera Auto Brightness E. Camera Auto Adjust D /Reference: QUESTION 41 Which statement is correct when discussing the table segment markers in a Cisco Telepresence System 1300 room? A. You should allow 48 inches (112 cm) for the center segment B. You should allow 60 inches (180 cm) for the center segment C. The table segment markers are placed at the left and right side of the Whip. 3fi inches (91 cm) from the center, to indicate the center camera segment D. The table segment marker placement is determined during the camera zoom adjustment /Reference: QUESTION 42 DRAG DROP Please see below the correct order.

16 A. Assemble the frame components to the frame. Obtain the mounting hardware. Mark the location on the wall to mount the Cisco TelePresence System Drill the holes for the mounting hardware. Attach the frame to the wall B. Mark the location on the wall to mount the Cisco TelePresence System Attach the frame to the wall. Obtain the mounting hardware. Assemble the frame components to the frame. Drill the holes for the mounting hardware. C.. Drill the holes for the mounting hardware. Mark the location on the wall to mount the Cisco TelePresence System Assemble the frame components to the frame. Obtain the mounting hardware. Attach the frame to the wall. D. Obtain the mounting hardware. Mark the location on the wall to mount the Cisco TelePresence System Assemble the frame components to the frame. Drill the holes for the mounting hardware. Attach the frame to the wall. Correct Answer: A /Reference: QUESTION 43 Which is correct when determining a background color for a Cisco TelePresence room? A. B. C. D. select a bright color that draws attention select white so everything stands out in front of it select the darkest colors so the plasmas will render other colors more accurately select neutral tones to give the appearance of warmth without too much distraction Correct Answer: D /Reference: QUESTION 44 Which statement is correct when installing the camera cluster for the Cisco Telepresence System 1300? A. Four black plastic screws on top of the camera assembly secure the camera cover B. The cameras are set up correctly when images are centered, in focus on the display screens, and the white balance is configured

17 C. The camera cluster needs to be secured to the frame after leveling screw down the center screw m the back of the camera cluster to secure it to the frame D. To configure the camera property, the camera cluster need not be perfectly level, because you can level each camera separately Correct Answer: A /Reference: QUESTION 45 Which is not a feature of the Cisco Telepresence System 500? A. The system has a built-in embedded microphone array. B. The system supports life-size images on the display. C. The system has a built-in facade lighting control D. The system has two embedded speakers to support wideband audio /Reference: QUESTION 46 What are two advantages of using the Cisco Telepresence System? (Choose two) A. The system can replace face-to-face meetings B. The remote participant appears smaller than real life size but can be heard clearly C. The system transmits and displays the position, voice, and body movements of each participant in real time by creating the illusion of a life-size face-to-face conversation D. The system is user-friendly with a remote control interface similar to television Correct Answer: AC /Reference: QUESTION 47 The Cisco IP Phone gives you the ability to control meetings and enable features depending on the configuration and models. Which three items can the Cisco IP Phone control? (Choose three.) A. Power on/off the projector B. Power on/off the Document Camera C. Turn on/off Presentation-in-Picture D. Adjust the brightness of the plasma displays. E. The Switching Mode for calls F. Video participants in a multipoint call CE

18 /Reference: QUESTION 48 How does Cisco define Telepresence? A. a high-definition video-conferencing system B. a high-definition video system installed in a studio-quality conference room C. a high-definition video system with spatial audio installed in a studio-quality conference room D. a technology that allows people who are miles apart to feel like they are in the same room E. a technology that allows a large group of people to experience video conferencing Correct Answer: D /Reference: QUESTION 49 Which statement is correct when discussing the Cisco Telepresence System 1000? A. The system supports four participants on each side around a virtual table for up to eight participants in a point-to-point meeting B. The system is designed to be flush-mounted along a wall space to easy use in smaller footprint areas C. The system is designed to be a free-standing system when purchased with the optional pedestal base D. The system uses the same frame and assembly structure that is used in the Cisco TelePresence System 1300 /Reference: QUESTION 50 What is the command path and action on the Cisco TelePresence codec WebGUI to place the camera in loopback mode? A. Configuration > Hardware Setup > Cameras and click Start B. Hardware Setup > Configuration > Cameras and click Start C. Troubleshooting > Hardware Setup > Cameras and click Start D. Configuration > Troubleshooting > Cameras and click Start /Reference: QUESTION 51

19 What is the minimum room size recommended for the Cisco TelePresence System 1300 with a short racetrack style table? A. 15 feet wide by 13 feet deep B. 18 feet wide by 13 feet deep C. 19 feet wide by 13 feet deep D. 23 feet wide by 13 feet deep /Reference: QUESTION 52 Which shipment is correct when focusing the camera on the Cisco Telepresence System 500? A. The green rectangle on the display is aligned with the small target B. The green rectangle on the display is aligned with the large target C. The red rectangle on the display is aligned with the small target D. The red and green bars must be the exact same length for proper calibration E. It does not matter which target is aligned with which rectangle as long as each rectangle is aligned with one of the targets /Reference: QUESTION 53 Which two statements are correct when connecting a laptop direct to a codec to issue commands from the CLI? (Choose two) A. Connect a PC to the secondary Ethernet camera port of the Cisco TelePresence codec. B. The Cisco TelePresence codec has two internal subnets ( X/24 and X/24) that are reserved for the secondary camera port. C. By default, the username is Admin with a password of Cisco. D. The Cisco TelePresence System IP address on the secondary camera port is the first address in the subnet that is assigned to your laptop by DHCP Correct Answer: AD /Reference: QUESTION 54 Which statement is correct when discussing the Cisco Telepresence System 1000? A. The ACU cannot be used with the Cisco Telepresence System 1000 because it is not a supported device. B. The HFR codec cannot be used with the Cisco Telepresence System 1000 because it is not supported and

20 (here is no location to mount it) C. The ACU, the External Presentation display, and the HFR codec are supported with the Cisco TelePresence System 1000 D. The Cisco TelePresence System 1000 does not support External Presentation displays because it supports Presentation in Picture /Reference: QUESTION 55 Which protocol is used by the primary codec to download its configuration from Cisco Unified Communications Manager? A. TFTP B. SFTP C. HTTP D. HTTPS /Reference: QUESTION 56 Which measurement is performed on the Acoustilyzer AL1 that filters out low frequency sound to approximate the response of the human ear? A. A-weighted SPL B. C-weighted SPL C. RTA SPL D. RT-60 SPL Correct Answer: A /Reference: QUESTION 57 To enable One Button to Push for a Cisco Telepresence endpoint, which two assignments must be made to a Room Name? (Choose two) A. primary SMTP address format B. Domino Canonical address format C. display name of the account for the room resources D. secondary SMTP address Correct Answer: AC

21 /Reference: QUESTION 58 What is the valid range of gain for the correct white color balance? A. greater than 1 and less than 5 B. greater than 2 and less than 5 C. greater than 1 and less than 7 D. greater than 2 and less than 7 /Reference: QUESTION 59 Which statement is correct when discussing room materials for a Cisco Telepresence room? A. The audio subsystem is not designed to deliver excellent performance for normal drywall room surfaces B. Standard drywall walls with a smooth finish are preferred. C. Walls and wall coverings with a heavy texture are encouraged. D. Cinder block and brick can be highly reverberant and therefore will likely require a coat of paint E. Thin walls and doors should be enough to block unwanted sound from leaking into the room /Reference: QUESTION 60 How far should the bottom of the camera target be from the ground when adjusting the cameras for a Cisco TelePresence System 1300? A. 22 inches (56 cm) B. 32 inches (81 cm) C. 42 inches (107 cm) D. 48 inches (122 cm) /Reference: QUESTION 61 What are three reasons a dedicated CUCM cluster is recommended for Cisco Telepresence systems? (Choose

22 three) A. The endpoints are able to connect faster B. Easier to manage Cisco Telepresence systems related CUCM upgrades C. Can prioritize Cisco Telepresence traffic separate than other video traffic D. Some endpoints do not work with Cisco IP Phones E. Production environment may not be running minimum CUCM version required for Cisco Telepresence F. Easier to create trunks with a dedicated CUCM cluster CE /Reference: QUESTION 62 Refer to the exhibit. The Cisco Telepresence System 1300 camera is leveled by adjusting which two 3-mm screws? A. the camera up and down adjust screws B. the camera left and right rotation screws C. the camera left and right adjust screws D. the camera zoom and focus rings

23 /Reference: QUESTION 63 Using a supported browser, where must you navigate to test each component from the WebGUI of the Cisco Telepresence codec? A. Configuration > Hardware Setup B. Troubleshooting > Configuration Issues C. Configuration > System Settings D. Troubleshooting > Hardware Setup Correct Answer: D /Reference: QUESTION 64 Given (the following): Cisco Telepresence endpoint A: Phone field Disable Speakerphone and Headset is checked. DN configuration Auto answer is enabled. Cisco Telepresence endpoint B: Phone field: Disable Speakerphone and Headset is unchecked. DN configuration: Auto answer is enabled What happens when Cisco Telepresence endpoint A calls Cisco Telepresence endpoint B? A. Cisco Telepresence endpoint A gets a fast busy B. Cisco TelePresence endpoint B gets a ring, and the call will establish as an audio-only call out of the Cisco IP Phone C. Cisco TelePresence endpoint B gets a ring, and the call will establish as a video-only call D. Cisco TelePresence endpoint B gets a ring, and the call will establish, but there is no audio or video /Reference: QUESTION 65 Which device will cause a Cisco TelePresence call to drop if not plugged in? A. microphone B. camera HDMI C. camera Ethernet

24 D. speaker E. Auto-Collaborate cable /Reference: QUESTION 66 Which statement is correct when discussing the big camera target placement for tuning the Cisco Telepresence System 1300 center camera? A. Position the table so that there is a minimum of 34 inches (86 cm) between the display and the front of the table, and make sure that the sides of the table are evenly positioned on each side of the endpoint B. Raise and lower the front legs of the easel until the bottom of the camera target is 48 inches (122 cm) above the ground C. Place the large camera target with the easel in front of the table closest to the display where the center two participants will sit. The back legs of the easel should be touching the edge of the table D. Measure the distance between the corners of the easel and the corners of the display to make sure that the target is centered and parallel to the display Correct Answer: D /Reference: QUESTION 67 What are the power requirements for Cisco Telepresence System 1100? A. The power receptacles must be located behind the endpoint B. The power receptacles must not be located behind the unit, and no closer than 6 feet (122 cm) away from the center of the cabinet C. Twin power receptacles are required with one dedicated circuit D. Four power receptacles are required with two dedicated circuits /Reference: QUESTION 68 In a Cisco Telepresence room, what are the two locations that should be used for the HVAC supply and return registers? A. The return registers should be located above the participants B. The return registers should be located above the Cisco Telepresence equipment C. The return register should he located in the center of the room D. The supply registers should be located above the participants E. The supply registers should be located above the Cisco Telepresence equipment

25 F. The supply register should be located in the center of the room D /Reference: QUESTION 69 When building the large camera target for the Cisco Telepresence 1300, the target is placed on the easel with the bottom edge of the target what distance from the ground? A. 28 inches B. 30 inches C. 32 inches D. 34 inches /Reference: QUESTION 70 Which statement is correct when making preliminary adjustments to the vertical height of the display for a pedestal stand-mounted Cisco TelePresence System 500? A. Raise the pedestal stand to its maximum height B. Ensure that the user is at least 4 feet (1.2 meters) away from the display C. The distance between eye level and the floor is 48 inches if the user height is unknown D. Ensure that the user is at least 4 feet (1.2 meters) away from the display and that the display height is set to 52 inches /Reference: QUESTION 71 Which statement is correct when discussing the Cisco TelePresence System 1100? A. The system is designed for one to two participants on camera in Cisco Telepresence meetings B. The system is designed for two of six participants to be displayed on camera at one time C. The system incorporates the design of the Cisco Telepresence System 1300; however, it has a single 37- inch plasma display D. Video integration with digital signage is supported during a Cisco Telepresence call Correct Answer: A

26 /Reference: QUESTION 72 What is the most effective way to improve the continuity of a Cisco Telepresence room? A. lighting fixtures B. adornments C. room color D. artwork /Reference: QUESTION 73 What is the cisco recommendation for power and Ethernet sources location before installing the Cisco Telepresence System 1300? A. Directly behind at centre B. To the right, two feet from centre C. To the left, three feet from the centre D. Either the left or right side, no less than four feet from centre. Correct Answer: D /Reference: QUESTION 74 When booting the Cisco TelePresence 500, how do you determine which IP address is used by the codec before connecting to the code via webgui? A. The codes uses as its default IP setting. B. The IP address is displayed on the phone user interface C. The IP address is displayed during the boot process on the plasma D. The codec uses as its default IP setting /Reference: QUESTION 75 Using the cisco Unified Communications Manager drop-down menu,where is WidebandAAC as Audio Codec for a Cisco telepresence endpoint set? A. Region

27 B. Device pool C. Location D. Service parameters Correct Answer: A /Reference: QUESTION 76 How high above the floor should the top stud holes for the mounting bracket be for a Cisco Telepresence System 1300? A. 25 inches B. 35 inches C. 45 inches D. 55 inches Correct Answer: D /Reference: QUESTION 77 Which two wall treatments does Cisco recommend for a Cisco TelePresence room? A. Use a glass wall B. Use flat paint with neutral color C. Use a wallpaper with neutral color D. Use a wood paneled wall E. Use a cinder block wall neutral color F. Use glossy paint with neutral color C /Reference: : QUESTION 78 Your customer would like you to connect a DVI-D output the Auto Collaborate video channel. What are your two connection option? A. Use a DVI-D to VGA make converter B. Use DVI to HDMI cable C. Use a VGA to DVI-A cable D. Use a M1 to DVI-D cable Correct Answer: AD

28 /Reference: QUESTION 79 What two statements are correct when configuring a static IP address for a Cisco Telepresence 1300 endpoint on a network that does not support DHCP? A. Connect a PC to the network Ethernet port of the Cisco Telepresence codec. B. Using SSH, start a CU session by using the first IP address in the subnet that is assigned to your laptop by DHCP. C. Enter utils service start calling-services to the start network services. D. Using a supported internet browser, log into the Cisco telepresence codec and navigate to hardware setup>ip settings E. Change the DHCP Enable setting to YES, and enter a static IP address, subnet mask, and IP gateway. Correct Answer: AD /Reference: QUESTION 80 Which section of Cisco Unified Communications Manager enables an A/V Expansion Box for a Cisco telepresence endpoint? A. Optional Hardware B. Protocol specific information C. Device information D. Product specific configuration layout Correct Answer: A /Reference: QUESTION 81 Refer to the exhibit.

29 The Cisco TelePresence System 1300 cameras is invented by adjusting which screws? A. The camera up and down adjust screws B. The camera left and right screws C. The camera left and right adjust screws D. The camera zoom and focus /Reference: QUESTION 82 Which statement is correct when discussing room materials for Cisco TelePresence Room? A. The audio subsystem is not designed to deliver excellent performance for normal drywall room surface. B. Standard drywall walls with a smooth finish are preferred. C. Walls and wall coverings with heavy textures are encouraged D. Cinder block and brick can be highly reverberant and therefore will likely require a cost paint. E. Thin walls and doors should be enough to block unwanted sound from leaking into the room

30 /Reference: QUESTION 83 What are available width options between the stud holes for the wall bracket to property install the Cisco TelePresence 1300? A. 18, 20, or 24 inches B. 16, 22 or 24 inches C. 18, 22 or 24 inches D. 16, 20 or 24 inches Correct Answer: D /Reference: QUESTION 84 Which statement is correct when discussing the Cisco TelePresence System 1300? A. The system is designed to support meetings of six to eight participants B. The system features three 85-inche screen, three cameras, microphones, and speakers C. Voice enabled switching is performed by the codec to select the active speaker in the room and capture the video for the remote side D. The power and Ethernet outlets must be positioned directly behind the unit. /Reference: QUESTION 85 Which three steps are required when turning the Cisco TelePresence System 1300 camera cluster? (Choose three) A. Level the camera cluster B. Tighten and lock down the camera cluster to the frame by using the side screws C. Tighten and lock down the camera cluster to the frame by using the centre screws D. Level the individual camera to ensure that is perfectly vertical E. Level the individual camera to ensure that is perfectly horizontal. Correct Answer: ADE /Reference: QUESTION 86 What are three key steps in the network readiness phase to ensure successful deployment of a Cisco TelePresence System?

31 A. network discovery B. network remediation plan and recommendations C. power and HV/AC capacity analysis D. network hardware, capacity, and ** gap analysis E. room analysis and selection Correct Answer: ABD /Reference: QUESTION 87 Where do you mount the optional presentation codec for the Cisco TelePresence System 1300? A. in the middle inside of the buttom assembly B. on the left side inside of the buttom assembly C. on the outside the assembly on the left side D. on the right side inside of the buttom assembly /Reference: QUESTION 88 What is the additional bandwidth consumption for the High Frame Rate codec to do 30 fps data collaboration? A. 2 Mbps B. 5 Mbps C. 4 Mbps D. 6 Mbps /Reference: QUESTION 89 The Cisco TelePresence System 1100 and 1300 left and right speakers are connected to which component? A. codec B. audio extension box C. POU D. light control box Correct Answer: A

32 /Reference: QUESTION 90 When setting the pedestal height on a new Cisco TelePresence System 500 installation, what is the correct procedure for proper adjustment? A. Loosen the height adjustment knob and push down the monitor until you believe that it is low enough for the user. B. Install the height label eight inches (20 centimeters) down from the top on the side of the pedestal stand and lower it to set it for the proper gender. C. Have the user sit in a chair and measure his or her eye level. Loosen the height adjustment knob and push down the monitor to set the height LED to eye level. D. Loosen the height adjustment knob and adjust the camera level to eye level. Correct Answer: D /Reference: QUESTION 91 In a Cisco Telepresence room, what are the two locations that should be used for the HVAC supply and return registers? A. The return registers should be located above the participants B. The return registers should be located above the Cisco Telepresence equipment C. The return register should he located in the center of the room D. The supply registers should be located above the participants E. The supply registers should be located above the Cisco Telepresence equipment F. The supply register should be located in the center of the room D /Reference: QUESTION 92 When booting the Cisco TelePresence 500, how do you determine which IP address is used by the codec before connecting to the code via webgui? A. The codes uses as its default IP setting. B. The IP address is displayed on the phone user interface C. The IP address is displayed during the boot process on the plasma D. The codec uses as its default IP setting /Reference:

33 QUESTION 93 What two statements are correct when configuring a static IP address for a Cisco Telepresence 1300 endpoint on a network that does not support DHCP? A. Connect a PC to the network Ethernet port of the Cisco Telepresence codec. B. Using SSH, start a CU session by using the first IP address in the subnet that is assigned to your laptop by DHCP. C. Enter utils service start calling-services to the start network services. D. Using a supported internet browser, log into the Cisco telepresence codec and navigate to hardware setup>ip settings E. Change the DHCP Enable setting to YES, and enter a static IP address, subnet mask, and IP gateway. Correct Answer: AD /Reference: QUESTION 94 Which three steps are required when turning the Cisco TelePresence System 1300 camera cluster? (Choose three) A. Level the camera cluster B. Tighten and lock down the camera cluster to the frame by using the side screws C. Tighten and lock down the camera cluster to the frame by using the centre screws D. Level the individual camera to ensure that is perfectly vertical E. Level the individual camera to ensure that is perfectly horizontal. Correct Answer: ADE /Reference: QUESTION 95 The Cisco TelePresence System 1100 and 1300 left and right speakers are connected to which component? A. codec B. audio extension box C. POU D. light control box Correct Answer: A /Reference:

34