EKI-6332 & EKI-136x- MB_setup example SOP. Revision Date Revision Description Author April/2018 V1.0 Initial release ICG AE Jacky.

Transcription

1 EKI-6332 & EKI-136x- MB_setup example SOP Revision Date Revision Description Author April/2018 V1.0 Initial release ICG AE Jacky.Lin 1

2 Abstract This SOP explains how to configure the EKI-6332 & EKI-136x-MB for polling the PLC Data on site. Related products: EKI-6332, EKI-1361-MB-AE Requirement: EKI-6332, EKI-1361-MB-AE, Note: If you use the PC to simulate the SCADA & PLC, Please download the Third party tool (Modscan & ModSim) for Simulation Test.

3 EKI-6332-EKI-136x-MB topology RS-232 Ethernet PC1 EKI-6332 EKI-1361-MB-AE PLC Wi-Fi Wi-Fi AP EKI-6332 Config: WLAN IP: SSID: testing Wi-Fi client EKI-1361 Config: WLAN IP: LAN IP: Modbus Slave mode Slave ID:1 Mapping ID:1

4 EKI-6332 set up

5 EKI-6332 Setting flow chart NB EKI-6332 Ethernet EKI-6332 WLAN IP: SSID: testing Step 1 :Connect the EKI-6332 via Ethernet cable Step 2 : follow the flow chart to set up EKI-6332 step by step. Log in Network Configuration Wireless Setting

6 Log in EKI-6332 Log in the configuration page via browser (Default IP address: ) You will see the login page as below Type in & Log in Default ID/ PW: Name: admin Password: password

7 Network Setting Enter IP Address, Subnet Mask for EKI-6332 and apply it

8 Wireless Network Settings - For AP Mode Step 1: Choose AP mode & Fill in the SSID e.g. testing Step 2: select Wi-Fi channel Step 3: adjust output power Step 4: after apply, you will see the broadcast SSID

9 Reboot the device Reboot the device and wait for starting the WiFi service

10 EKI-1361 set up

11 EKI-1361 Setting flow chart NB Ethernet EKI-1361 EKI-1361 Config: WLAN IP: LAN IP: Modbus Slave mode Slave ID:1 Mapping ID:1 Step 1 : Connect the EKI-1361 via Ethernet cable Step 2 : follow the flow chart to set up EKI-1361 step by step. LAN/WLAN Port Configuration Wireless Setting Serial Port Setting Data Test Serial Port Operation Mode

12 LAN/WLAN port Configuration Config LAN IP to be Config WLAN IP to be Step 1 : use EKI Utility to scan the EKI-1361 Step 4: Click Launch browser to enter Web GUI for other setting Step 2 : Config LAN to Then click apply Note: make sure your PC in the same subnet. Step 3 : Config WLAN to Then click apply

13 Wireless Setting Step 1 :Set to client mode Step 2 :Click Site survey and choose the AP broadcast SSID Step 3 :remember to save it

14 Serial Port Setting Set the communication type based on the connected PLC.

15 Serial Port Operation Mode Modbus Slave Mode Modbus Protocol :RTU/ASCII Slave Timeout: wait for slave device time interval Peer for Receiving Data : Slave ID : End device ID Mapping ID: Host remapping ID

16 Reboot and Run the ping test Step 1 :Reboot device after all setting done Step 2 : ping EKI-6332 to make sure the wireless connection is established EKI-6332 IP

17 Check wireless connection You may also check the Wi-Fi signal for AP/client on Web GUI EKI-6332 EKI-1361

18 Test by ModScan / ModSim tools

19 Test by Modscan / Modsim tools RS-232 Ethernet PC1 EKI-6332 EKI-1361-MB-AE PC2 Wi-Fi Wi-Fi AP Wi-Fi client Com port 3 ModScan Use Modscan tool to simulate the data center to send out the polling with Modbus TCP ModSim Use Modsim tool to simulate the end device to send out the data with Modbus RTU

20 ModSim tool set up Step 1: Click File and New Step 3: Select the protocol of Modbus RTU and set the parameter step 2: Click Connection, and select the COM Port

21 ModScan tool set up Step 1: Click Connection and Connect Step 2: select Remote TCP/IP Server IP Address: Fill in the IP of EKI-1361 WLAN ( ) 502 service port : Default setting of Modbus Step 3: Click Protocol Selections to select the protocol of Modbus

22 Result ModSim ModScan Device ID = Node of End device Data Type of Modbus, Address and Data Length Device ID = mapping ID Data Type of Modbus, Query Address and Length Double click to change the value ModScan sends polling request and read the value change from ModSim

23