COMPUTER NETWORK WIRING SYSTEMS FOR PLCs
|
|
|
- Edwina Crawford
- 5 years ago
- Views:
Transcription
1 SECTION COMPUTER NETWORK WIRING SYSTEMS FOR PLCs NOTE TO SPECIFIER: This section applies to primary learning centers only. PART 1 GENERAL 1.01 SUMMARY A. Section Includes: A complete computer network wiring system for data communications, including necessary accessories. B. Related Sections: Telephone and Data Raceway Systems Wire and Cable SUBMITTALS A. Submit properly identified manufacturer's literature and technical data to A/E before installation. B. Provide additional information as may be required by A/E to establish compliance with requirements of this section. C. Project Record Documents: Furnish a set of "Record Drawings" to A/E indicating accurate plan layout, conduit runs, and the like as actually installed QUALITY ASSURANCE A. Qualifications: The installer shall be a licensed electrical contractor with at least 10 years of experience installing data cables and equipment and certified by equipment manufacturer. All devices shall be installed as indicated and as specified by manufacturer's recommendations. 1. Provide tools, labor, and materials as necessary for a complete installation. B. Regulatory Requirements: Comply with current building and electrical requirements of: 1. National Electrical Code - NFPA 70 (NEC). Project No. GUIDELINE SPECIFICATIONS
2 2. Florida Building Code (FBC). 3. Manufacturer's Product Specification. 4. Fire Prevention and Control (Chapter 633) WARRANTY A. Provide 15 year warranty for each Level 5 Link as defined in EIA/TIA-568A and EIA/TIA-TSB-67, latest edition. PART 2 PRODUCTS 2.01 MANUFACTURERS A. Computer Network Wiring Systems: 2. Mohawk Cable. 3. Consolidated Datacom Data Cable, Division of Wilcox and Gibbs. 4. Interlink. 5. Panduit. B. Data Cables: 1. AT&T, types 1061A or 2061A. 2. Mohawk, types M54518 or M Consolidated Datacom Data Cable, Level 5 construction. C. Workstation Category 5 Outlet Jack: 2. Interlink. 3. Ortronics. 4. Panduit. D. Wiring Closet Cross-Connect Category 5 Jack Panel: 2. Interlink. 3. Ortronics. 4. Panduit. E. Plastic Cable Ties: TY-Rap or accepted equivalent. F. Adhesive Marking Tape: Bradley or accepted equivalent COMPONENTS A. Data Cable: The data cable shall be a Level 5, high Project No. GUIDELINE SPECIFICATIONS
3 performance 100 ohm, four-pair (No.24 AWG) twisted unshielded solid core copper cables, band marked insulation, tested and capable of transmitting data at speeds up to 100 Mbps. 1. Unshielded Data Cable in Metal Conduit: PVC coated. 2. Unshielded Data Cable Not in Metal Conduit: Plenum rated and FEP (teflon) coated. 3. Provide color-coded cables as follows: a. The EIA/TIA 568B wiring standard shall be used for data and voice jacks. b. This system requires: 1) Pair - 1 be wired to pins 4 and 5. 2) Pair - 2 be wired to pins 1 and 2. 3) 4) Pair - 3 be wired to pins 3 and 6. Pair - 4 be wired to pins 7 and 8. B. Fiber Optic Cable: Inside/outside 62.5/125 micron 12 stranded multimode fiber optic cable with snap type (ST) connectors. C. Workstation Outlets: 1. Workstation Outlet Jack: AT&T type M100 or equal. 2. Single Gang Faceplate: AT&T M16A fourplex, almondcolored plastic, or accepted equivalent. D. Wiring Closet Panel: 1. Cross-connect Category 5 Jack Panel: AT&T 1100 type or accepted equivalent. 2. A data communications backboard or terminal cabinet. E. Data Communication Backboard: 3 feet wide by 6 feet high by 3/4" thick plywood panel, painted gray with fire retardant paint. F. Terminal Cabinet: Great Lakes Case and Cabinet Co. or accepted equivalent. G. Communication Cabinets: P/N GLPP-2418, GLPP-4818, or GLPP PART 3 EXECUTION 3.01 INSTALLATION Project No. GUIDELINE SPECIFICATIONS
4 A. Metal Conduit Systems: 1. Install wires and cables for the computer network wiring systems in a metal conduit raceway system consisting of conduits, cable trays, appropriate supports, pull boxes, and outlet boxes to form an empty raceway system. 2. Conduit fill of any conduit shall not exceed 40 percent. B. Cables shall be pulled-in complete without splice from workstation outlet jack to wiring closet cross-connect jack panel. 1. Each above-ceiling J-box or pull box shall be used for pulling purposes only and shall be located in accessible locations. 2. Junction box blank covers shall be painted gray. C. Make terminations of twisted pair cables at workstation and wiring station panels edge connectors according to color code assigned to each terminal. Color-coded connections shall be the same throughout the work. D. Cables within wall mounted pull boxes shall be neatly bundled with plastic cable ties. Allow an equal amount of slack for cables. E. Identify cables from wiring closet panel to workstations with adhesive marking tape by workstation room number at each junction and pull box. Identify interconnection cables at wiring closet panel. F. Provide within each wiring closet panel a 20A, 125V, 3 wire, grounding type dual duplex receptacle. 1. Install the receptacle in a 4" x 4" x 2-1/8" deep box and connect to a dedicated circuit. 2. Provide an equipment ground. NOTE TO SPECIFIER: The following paragraph applies to new projects only. Edit to suit project requirements. G. Install fiber optic cable between wiring closets, if more than one wiring closet exists. NOTE TO SPECIFIER: The following paragraph applies to renovations and additions only. Edit to Project No. GUIDELINE SPECIFICATIONS
5 suit project requirements. H. Install fiber optic cable between the new wiring closet(s) and the nearest existing wiring closet(s). I. Terminate the fiber with ST connectors in a Lightguide Interface Unit (LIU) box at both ends or in a rack mounted termination/splice cabinet in the terminal cabinet. J. Install 4-pair twisted cables between the nearest new wiring closet and the new workstation locations (maximum wire run of 250 feet). K. Terminate the 4-pair twisted cables between the new closet(s) and workstation outlet locations on a crossconnect jack panel in the wiring closets and on a jack at the workstation outlet locations. L. Install a data communications backboard panel in each wiring closet FIELD QUALITY CONTROL A. Test, with a WAVETEK LAN cable tester, the following: 1. The connection of wiring of each work station outlet and corresponding wiring closet panel outlet. 2. The connection of fiber of each IDF to the MDF. B. Provide tests for the following conditions: 1. Continuity of each wire in the installed cable. 2. Short circuit condition between any wire of the cable and the metal conduit system. 3. Noise. 4. DC Loop Resistance Scan(cable length/distance to fault). Capacitance. 7. Impedance. 8. Attenuation. 9. Near-End Crosstalk. 10. Signal-to-noise ratio. 11. Meet EIA/TIA-568A and EIA/TIA-TSB-67 standards for CAT 5 for basic link. C. Replace defective cable/connections without additional cost to the Board. END OF SECTION Project No. GUIDELINE SPECIFICATIONS
Tarleton State University. Specifications
Tarleton State University Campus Communication Infrastructure Specifications Cabling Standards Summary This document identifies Tarleton State University communication infrastructure standards. The communication
Copper Riser And Intrabuilding Cabling
Copper Riser And Intrabuilding Cabling PART 1: GENERAL The Contractor is held responsible to be familiar with the provisions contained herein and with other Sections of this Specification as applicable
A. System design shall be completed by a Registered Communications Distribution Designer (RCDD).
UDIVISION 27 COMMUNICATIONS 27 00 00 COMMUNICATIONS A. System design shall be completed by a Registered Communications Distribution Designer (RCDD). B. Comply with American National Standards Institute
Computer Network Design Guide Existing Systems 1 / 6
COMPUTER NETWORK DESIGN GUIDELINE FOR EXISTING SYSTEMS DOCUMENT NUMBER: 16765 APPLICATION: ELEMENTARY, MIDDLE AND HIGH SCHOOL DATE OF ISSUE: 11-27-06 - First Issued NOTES: The attached guideline should
SPECIFICATION STANDARD COPPER RISER AND INTRABUILDING CABLING
PART 1: GENERAL 1.01 SCOPE OF WORK A. The Designer and Contractor are responsible to be familiar with the provisions contained herein and with other Sections of this Specification as applicable to the
Office of the Chief Information Officer Technical Note: IT-960-TN14 Effective: 05/25/2006 Last Revised: 02/17/2012 Issuing Office: OCIO
Cabling Standards Office of the Chief Information Officer Technical Note: IT-960-TN14 Effective: 05/25/2006 Last Revised: 02/17/2012 Issuing Office: OCIO 1. Purpose CABLING STANDARDS This technical note
LACCD IT Design Standards
LACCD IT Design Standards March 1 2009 This document establishes a uniform standard for the design of IT Structured Cabling for LACCD. It ensures a secure, consistent, robust system with physical and low-voltage
UMass Lowell. October 1, Network and Voice Infrastructure Specifications Prepared by Network Engineering and Network Project Management
UMass Lowell October 1, 2011 Network and Voice Infrastructure Specifications Version 5.1 Prepared by Network Engineering and Network Project Management TABLE OF CONTENTS NETWORK AND VOICE INFRASTRUCTURE
TIA/EIA 568A Sub-system HORIZONTAL CABLING
TIA/EIA 568A Sub-system HORIZONTAL CABLING Horizontal Cabling WA 100(120)Ω CAT 3 TP TP 100(120)Ω CAT 5 150Ω STP-A 62.5(50)/125µ FIBER HC/FD WA Horizontal Media Considerations UTP/FTP Consider bandwidth,
SECTION COMMON WORK RESULTS FOR COMMUNICATIONS
PART 1 - GENERAL SECTION 270500 - COMMON WORK RESULTS FOR COMMUNICATIONS 1.1 RELATED SECTIONS A. All division 27 work shall, in addition to all division 1 specification sections, comply with all of the
COMMON WORK RESULTS FOR COMMUNICATIONS
SECTION 270500 - COMMON WORK RESULTS FOR COMMUNICATIONS PART 1 - GENERAL 1.1 RELATED SECTIONS A. All division 27 work shall, in addition to all division 1 specification sections, comply with all of the
Network Construction Guide Specification Telecommunications Infrastructure Standards V 2.6
Network Construction Guide Specification Telecommunications Infrastructure Standards 11-16-2018 V 2.6 Springfield Public Schools R12 Prepared by: Approved by: Released by: Springfield Public Schools R12
Division 27 Master Specification for
Division 27 Master Specification for Information Transport Systems and Spaces December 1, 2018 1 Table of Contents 1 Section 27 10 01 Structured Cabling General Requirements 1.1 Scope 1.2 Approved Contractor
Newark, Delaware Architectural Engineering Senior Thesis Portfolio
Telecommunications System Design The represents the advancement of solar design in our world today. The building itself is an example of this. A Headquarters this dedicated to moving into the future should
Government of Prince Edward Island Structured Cabling Standards August 24, 2009
Government of Prince Edward Island Structured Cabling Standards August 24, 2009 Emerging technologies dictate that it is no longer allowable to simply integrate various manufacturers components into a
ANSI/TIA/EIA-568-B Cabling Standard
73 ANSI/TIA/EIA-568-B Cabling Standard In the mid-1980s, consumers, contractors, vendors, and manufacturers became concerned about the lack of specifications relating to telecommunications cabling. Before
The 5500 Series from The Wiremold Company
5500 Nonmetallic Raceway Multi-Channel Surface Nonmetallic Raceway Available Factory Prewired. The 5500 Series from The Wiremold Company provides wire and cable management for data, voice, video, and power
Target Interface / Construction Compliance Inspection Checklist
TES A. Roads-Service, Lanes Common Items Trails and service roads provide adequate access to buildings for maintenance B. Testing Results-provided to the local government construction representative Data
INTERIM COMMUNICATIONS INFRASTRUCTURE PLANNING GUIDELINES
INTERIM COMMUNICATIONS INFRASTRUCTURE PLANNING GUIDELINES University of California, Riverside Computing and Communications April XX, 2001 R1V6 TABLE OF CONTENTS Introduction and Background...3 Outside
The University of Texas at Austin July 30, 2014 SECTION COMMUNICATIONS TERMINATION BLOCKS AND PATCH PANELS
SECTION 27 11 19 COMMUNICATIONS TERMINATION BLOCKS AND PATCH PANELS PART 1 - GENERAL 1.1 SUMMARY A. This section specifies the products and installation of communications termination blocks and patch panels
The 5400 Series Raceway from The Wiremold
5400 Nonmetallic Raceway Nonmetallic Raceway with Twin Snap Cover System Available Factory Prewired The 5400 Series Raceway from The Wiremold Company provides wire and cable management for data, voice,
The six major components of a structured wiring system are:
OBJECTIVES 1. Describe various ANSI/TIA/EIA standards for commercial buildings and residential settings. 2. Discuss the specific Technical Systems Bulletins that can affect telecommunications installations.
Data Cabling / Low Voltage Technology Specifications
P19-02- Forsyth County Schools Data Cabling / Low Voltage Technology Specifications 1. General requirements 1.1 On premise connectivity All building closets (IDF) aside from the main closet (MDF) shall
Emery County Senior Center Green River 06/07
SECTION 262726 - WIRING DEVICES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
Communications Updated April
27 00 00 Communication 27 05 00 Common Work Results for Communications 1. Purpose a. Coastal Carolina University facilities requiring cabling installation. This document provides the minimum performance
SECTION COMMUNICATIONS OPTICAL FIBER BACKBONE CABLING
SECTION 27 13 23 COMMUNICATIONS OPTICAL FIBER BACKBONE CABLING PART 1 GENERAL 1.01 DESCRIPTION A. The work covered by this section of the Specifications includes all labor necessary to perform and complete
Los Angeles Community College District Design Standards
LACCD Facilities Design Standards - Structural Cabling and Telecommunications Room Facilities Ver Approved: DTC February 0, 0 LACCD has developed the following Districtwide standard for IT infrastructure
SECTION FARE COLLECTION SYSTEM
SECTION 17830 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes requirements for the Ticket Vending Machines (TVMs) and for the Clipper Network Card Interface Devices (CIDs) as a subsystem of the station
SPECIFICATION STANDARD
PART 1: GENERAL 1.01 SCOPE OF WORK SPECIFICATION STANDARD A. Work covered by this Section shall consist of furnishing labor, equipment, supplies, materials, and testing unless otherwise specified, and
SPOS (Station Point of Sale) 200. SFTP (Station Fare Transaction Processor) 35. CQD (Card Query Device) 35. HCR (Handheld Card Reader) Cradles 120
DESIGN GUIDELINES PRESTO INSTALLATION & CONNECTIVITY PAGE 1 of 4 ELECTRICAL CONNECTIVITY AND WIRING Communications Conduits Conduits designated for Presto equipment data wiring shall be clearly identified
ANSI/TIA/EIA-568-B A P P E N D I X TECHNICAL INFORMATION. Contents ANSI/TIA/EIA-568-B. anixter.com
A The urpose: stablish a generic telecommunications cabling standard that will support a multivendor environment nable the planning and installation of a structured cabling system for commercial buildings
NZQA registered unit standard version 2 Page 1 of 7. Demonstrate basic knowledge of electronic security data protocols and cabling
Page 1 of 7 Title Demonstrate basic knowledge of electronic security data protocols and cabling Level 3 Credits 15 Purpose This unit standard is for electronic security installers engaged in the installation
UNIVERSITY OF CALICUT (Purchase Division)
No. 12831/PURCHASE-ASST-A1/2013/CU UNIVERSITY OF CALICUT (Purchase Division) Calicut University. P.O., Dated, 07.06.2013. TENDER NOTICE Sealed and competitive tenders are invited for the installation of
Interconnect Product CATALOG Q700
onents.com Interconnect Product CATALOG Q700 Quest Network Quest Network Warranty Products Warranty Que st Technology International Inc., carries a LIFETIME warranty on all Category- Rated link components
AT&T Dedicated Internet (ADI formerly known as MIS) and Private Network Transport (PNT)
AT&T Dedicated Internet (ADI formerly known as MIS) and Private Network Transport (PNT) Site Preparation Guide 2015 AT&T Intellectual Property. All rights reserved. AT&T, the AT&T logo and all other AT&T
SECTION WIRING DEVICES PART 1 - GENERAL. A. Drawings and Division 1 Specification Sections, apply to this Section.
SECTION 16140 WIRING DEVICES 1.01 RELATED DOCUMENTS PART 1 - GENERAL A. Drawings and Division 1 Specification Sections, apply to this Section. 1.02 SUMMARY A. This Section includes receptacles, connectors,
SECTION WIRING DEVICES
PART 1 - GENERAL... 1 1.1 RELATED DOCUMENTS... 1 1.2 SUMMARY... 1 1.3 DEFINITIONS... 1 1.4 REFERENCES... 2 1.5 SUBMITTALS... 2 1.6 QUALITY ASSURANCE... 2 1.7 COORDINATION... 2 PART 2 - PRODUCTS... 2 2.1
SECURE NETWORK INFRASTRUCTURE POLICY
Responsible University Administrator: Vice Provost for Academic Affairs Responsible Officer: Chief Information Officer Origination Date: N/A Current Revision Date: 02/19/13 Next Review Date: 02/19/17 End
SECTION COMMUNICATIONS BACKBONE CABLING
(NOTE TO DESIGNER: These Specifications are basic minimum criteria to be met in preparing the final specifications for this section, which is the responsibility of the Designer.) PART 1 GENERAL 1.1 RELATED
Cabling Infrastructure
Introduction Ethernet Banking on Structured Cabling Technology Drivers Classification of Cables Fibre-optic cable Cables in building Cabling Infrastructure Cabling systems address the networking requirements
5500 Series Nonmetallic Raceway
5500 Series Nonmetallic Raceway Multi-Channel Nonmetallic Raceway System Available Factory Prewired. A/V INTEGRATION COMMUNICATIONS FIBER OPTIC CAT5 Wiremold 5500 Series Raceway from provides wire and
Cables and Connectors
Module 2 Cables and Connectors Twisted Pair Two wires that carry the data signals (one conductor carries a positive signal; one carries a negative signal). Two wires are twisted to reduce the effects of
E. Numbering and Labeling Pathway components. In general, pathway components are not labeled.
27 05 53 Identification (Labeling) for Communications Systems (Revision date: 3/6/13) 1.0 Purpose A. These guidelines provide requirements for designers to incorporate into bid documents. They are part
AL4400 Series Isoduct Aluminum Raceway
AL4400 Series Isoduct Aluminum Raceway Aesthetic Dual-Channel Raceway Available Factory Prewired. COMMUNICATIONS SURGE PREWIRED Wiremold AL4400 Series Raceway is a two-channel, single-cover, cost effective
This Wiremold aluminum raceway system meets the
Architectural Aluminum Raceway AL3300 Aluminum Raceway This Wiremold aluminum raceway system meets the demands of today's commercial spaces, providing a compact, handsome and effective method of consolidating
9/27/04 cci Cablecom Inc. 1
cci Cablecom Inc. 1 CCI Cablecom Inc. is a privately held, women owned corporation headquartered in Aurora, CO. We manufacture a variety of voice and datacom products. Cable applications Include: Local
Information Transport Systems and Spaces
Division 27 Master Specification for Information Transport Systems and Spaces 1 Table of Contents 1 Section 27 10 01 Structured Cabling General Requirements 1.1 Scope 1.2 Approved Contractor 1.3 Submittals
f) Telecommunications Equipment Rooms
SECTION 270000 - COMMUNICATIONS PART 1 - GENERAL 1.1 GENERAL REQUIREMENTS A. The Contractor is held responsible to be familiar with the provisions contained herein and with other Sections of this Specification
AT&T Dedicated Internet (ADI formerly known as MIS) and Private Network Transport (PNT)
AT&T Dedicated Internet (ADI formerly known as MIS) and Private Network Transport (PNT) Site Preparation Guide This guide is designed to assist local on-site contacts to understand what you will need to
Communications. UNM IT/Telecommunications Guide Specification Communications
The material below covers specific information we definitely want to be included in the contract documents and may not be a completed specification section. This material is to be highlighted in your preliminary
3 Chapter Introduction. 3.2 Copper Cable
3 Chapter 3 3.1 Introduction The Network Media is the device that physically carries the data from computer to computer. The three major types of network media are: Copper Cable Fiber-Optic Cable Wireless
MICHIGAN DEPARTMENT OF TRANSPORTATION
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR GROUNDING, BONDING, LIGHTNING PROTECTION AND SURGE PROTECTION FOR INTELLIGENT TRANSPORTATION SYSTEM EQUIPMENT ITS:CLC 1 of 5 APPR:LWB:DBP:07-31-13
With its tamper-resistant design, the
Dual-Channel 40N2 Series Nonmetallic Raceway Systems CableSmart Series Nonmetallic Raceway With its tamper-resistant design, the CableSmart 40N2 Series Raceway is ideal for schools or office settings,
Power/Data Instructions. Genius. Movable Walls. September
Power/Data Genius Movable Walls September 2011 Genius Movable Walls Power and Data in Shell Level 1 Conventional Boxes in Panel (conventional box and conduit) Choose 2x4 box or 4x4 box (shown). Separate
CableSmart Series Nonmetallic Raceway
CableSmart Series Nonmetallic Raceway Dual-Channel 40N2 Series Nonmetallic Raceway System FIBER OPTIC CAT5 Wiremold CableSmart 40N2 Series Raceway is a large capacity nonmetallic raceway system that offers
Specifications for Modular Sound Shadow Sound Masking Sound Management Group, LLC.
Specifications for Modular Sound Shadow Sound Masking Sound Management Group, LLC. 1.01 General Requirements This section details general requirements for plenum sound masking installations. 1.1 Contract
WIREMOLD Nonmetallic Raceway
Multi-Channel Nonmetallic Raceway System Available Factory Prewired. 5500 Series Raceway from provides wire and cable management for data, voice, A/V, and power applications. It is ideal for large cable
SECTION WIRING DEVICES
SECTION 26 27 26 WIRING DEVICES PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Receptacles, receptacles with integral GFCI, and associated device plates. 2. Twist-locking receptacles.
ANSI/TIA/EIA-568-B Cabling Standard
83 Pair Numbers and Color Coding The conductors in a UTP cable are twisted in pairs and color coded so that each pair of wires can be easily identified and quickly terminated to the appropriate pin on
Classroom WiFi Network Infrastructure Plan
Seattle Archdiocese Office for Catholic Schools Design for Classroom WiFi Network Modernization Guidelines for IT Physical Infrastructure Design and Specifications This document provides guidelines to
Structured Cabling Guidelines
Informatics Planning and Services Structured Cabling Guidelines Version 1.7 August 2015 Informatics Planning and Services 1 Version 1.7 TABLE OF CONTENTS SECTION 1 STATEMENT OF PURPOSE... 1 SECTION 2 APPLICABLE
v2.5 was updated May 10, v2.6 is an updated copy from March 1, 2017.
Changes in v2.6: v2.5 was updated May 10, 2016. v2.6 is an updated copy from March 1, 2017. Modifications to 4. Horizontal Pathways section with feedback incorporated from UofA Facilities and Operations
University of Arkansas at Little Rock
University of Arkansas at Little Rock Policy Name: Infrastructure Cabling and Wiring Standards Policy Number: 702.1 Effective Date: September 24, 2008 Policy: University of Arkansas at Little Rock (UALR)
Anticipating Cat 8 Agenda. Cat 8 Overview Cat 8 Customer Design Considerations Testing Procedures and Standards
Anticipating Cat 8 Agenda Cat 8 Overview Cat 8 Customer Design Considerations Testing Procedures and Standards What is Cat 8? Next Generation Copper Cabling 25G and 40G data rates over twisted pair copper
Technology Standards
June 6, 211 Communications Infrastructure Cabling Services ITB Addenda #1 APPENDIX D, Revision 3.3, dated May 19, 26, is replaced in its entirety, with APPENDIX D, Revision 9, dated April 211, per the
This attractive raceway conceals and
5000 Two-Piece Multiple Channel Raceway Access 5000 Nonmetallic Surface Raceway System This attractive raceway conceals and organizes electrical wiring and low-voltage cabling in a sleek, handsome molding.
Element Z General Design Requirements Owner Standards and Other Requirements
Element Z General Design Owner and Other IS Network Services & PART 1 - General Information...2 1.01 Background...2 1.02 Scope...2 1.03 Additions, changes, testing, and acceptance...2 1.04 Special cases
STRUCTURED CABLING GUIDELINES. for PALM BEACH STATE COLLEGE
STRUCTURED CABLING GUIDELINES for PALM BEACH STATE COLLEGE Palm Beach State College 4200 Congress Avenue Lake Worth, Florida 33461-4796 Prepared by: IT Department, Palm Beach State College Revision #8
Al uminum Raceway is sleek, clean and
Architectural Aluminum Raceway AL5200 Aluminum Raceway Al uminum Raceway is sleek, clean and attractive. Integrated into casework or lab furniture or installed as baseboard, these raceways distribute communication
Family of Cords SYSTIMAX. Structured Cabling Systems. Quality Stranded and Solid Cords That Connect Data and Voice Circuits
SYSTIMAX Structured Cabling Systems Family of Cords Quality Stranded and Solid Cords That Connect Data and Voice Circuits Lucent Technologies Family of Stranded Cords includes 110 patch, modular and adapter
SECTION TELECOMMUNICATIONS TESTING AND DOCUMENTATION
SECTION 17045 TELECOMMUNICATIONS TESTING AND DOCUMENTATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including Facilities Management Design and Construction
This attractive raceway conceals and
Access 5000 Nonmetallic Surface Raceway System 5000 Two-Piece Multiple Channel Raceway This attractive raceway conceals and organizes electrical wiring and low-voltage cabling in a sleek, handsome molding.
ANSI/TIA-568-C Cat 6A Field Test Specifications
This document has been prepared to aid consultants or engineers in developing contractual specifications covering the certification of Category 6A Permanent Links. It is offered as a general guide. Suitability
SECTION TELEPHONE AND COMPUTER CABLING
SECTION 16700 TELEPHONE AND COMPUTER CABLING PART 1 - GENERAL Verify the computer and telephone cabling standards with MINES CCIT and Telecommunications departments. Telephone and computer lines shall
Cabinet Location Plan FIG.01. Cabinet Symbol Key. Air Handler. Air Handler SAN disk storage. SAN disk storage. option B. Not To Scale.
Cabinet front face - 09 Data Center Storage / Fit-Up Square Feet Square Meters Up Cabinet Symbol Key A Network Row A Network Substation B Server Cabinet A A A A4 A A6 A7 A8 A9 FIG.0 Data Center Square
REQUEST FOR PROPOSAL:
REQUEST FOR PROPOSAL: FIBER CABLING INSTALLATION TO CONNECT SIX ADDITIONAL VIEWING STATIONS AT THE EMERGENCY OPERATION CENTER (EOC) WITH THE REGIONAL VIDEO COMMAND CENTER (RVCC) VIDEO FEED I. DESCRIPTION
The EMITEX PRODUCT GUIDE 2018/19
The EMITEX PRODUCT GUIDE 2018/19 ABOUT US QUALITY GUARANTEED Emitex was established in 2002, and since then has gone from strength to strength, becoming one of the most recognisable brands in the voice
SECTION WIRING DEVICES
SECTION 16141 WIRING DEVICES PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
ELLIS COUNTY COURTS AND JAIL EXPANSION. SECTION Communications Cabling Infrastructure ADDENDUM #4. Table of Contents
ELLIS COUNTY COURTS AND JAIL EXPANSION SECTION 17000 Communications Cabling Infrastructure ADDENDUM #4 Table of Contents 1.0 REQUEST FOR PROPOSAL OVERVIEW... 2 1.1 Purpose... 2 1.2 Proposed System... 2
Termination for 568A and 568B pin configurations.
1 Termination for 568A and 568B pin configurations. The four twisted pairs in Unshielded Twisted Pair (UTP) cabling terminate in eight-pin modular jacks. There are two different pin configurations permitted
SECTION IDENTIFICATION FOR ELECTRICAL SYSTEMS
SECTION 26 05 53 IDENTIFICATION FOR ELECTRICAL SYSTEMS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Nameplates. 2. Labels. 3. Wire markers. 4. Conduit markers. 5. Underground Warning Tape. 6. Lockout
SECTION MODEL 2577 INDOOR SCOREBOARD. A. Single-face electronic scoreboard and control console for indoor use.
SECTION 116643 MODEL 2577 INDOOR SCOREBOARD PART 1 GENERAL 1.01 SECTION INCLUDES A. Single-face electronic scoreboard and control console for indoor use. 1.02 REFERENCES A. Standard for Electric Signs,
The 400, 800, and 2300 Series, from
400, 800, 2300, 2300D Surface Nonmetallic Raceway Systems For Low Voltage and Power pplications 400, 800, 2300, 2300D Series Raceway Systems The 400, 800, and 2300 Series, from The Wiremold Company, is
SECTION WIRING DEVICES PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 26 27 26 - WIRING DEVICES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
Run lots of CAT5 and CAT5e cable to support different high-speed applications and know at a glance which cable is for which purpose.
2007. All rights reserved. Black Corporation. FREE 24-hour Tech Support: 724-746-5500 blackbox.com CAT5/CAT5e Shielded and Unshielded Cables Run lots of CAT5 and CAT5e cable to support different high-speed
USER MANUAL MODEL 570-R8/570-R R8/580-R Base-T (CAT-5) Surge Protectors
USER MANUAL MODEL 570-R8/570-R16 580-R8/580-R16 100Base-T (CAT-5) Surge Protectors C E R T I F I E D An ISO-9001 Certified Company Part #07M570/580RC-A Doc# 074101UA Revised 2/13/97 SALES OFFICE (301)
SECTION 2 DIVISION 27 UNC CHARLOTTE ITS DEPARTMENT. ITS Telecommunications Standards - Specifications Manual for Construction and Renovations
SECTION 2 DIVISION 27 UNC CHARLOTTE ITS DEPARTMENT ITS Telecommunications Standards - Specifications Manual for Construction and Renovations Page 1 of 67 TABLE OF CONTENTS UNC Charlotte Information Technology
This attractive raceway conceals and
Access 5000 Nonmetallic Surface Raceway System 5000 Two-Piece Multiple Channel Raceway This attractive raceway conceals and organizes electrical wiring and low-voltage cabling in a sleek, handsome molding.
SECTION PANELBOARDS
SECTION 16450 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes requirements for panelboards providing fault interrupting capability and overcurrent protective devices. 1.02 REFERENCE STANDARDS A.
BEJED DISTRIBUTION PRODUCTS FAX:
1 BEJED DISTRIBUTION PRODUCTS 503.281.8153 800.232.3533 FAX: 503.281.3339 www.bejed.com Profile BEJED, Inc. s engineering designs have been supporting the telecommunications industry for over 30 years.
PANGEN SYSTEM WARRANTY. Warranty Guide
PANGEN SYSTEM WARRANTY Warranty Guide C2-10270 PANGEN SYSTEMWARRANTY GUIDE PROGRAM OUTLINE TABLE OF CONTENTS: MATERIALS PAGE # Program Outline 2 Table of Contents Warranty Information 3 Introduction &
WIREMOLD Aluminum Raceway
WIREMOLD Aluminum Raceway Architectural Twin Cover Raceway Available Factory Prewired. ALA4800 Series Isoduct Aluminum Raceway meets the demands of commercial spaces, providing a handsome and effective
WIREMOLD. Bring Wire & Cable Down to Business. Tele-Power Poles
Bring Wire & Cable Down to Business Routing power, data, and A/V neatly and simply from up there to down here; that s what Wiremold Tele-Power Poles are all about. Their sole purpose is to get the business
June
DESIGN CRITERIA 1. Related Sections: Division 01, Section 26 05 00, Design Standards 27 15 00-01 through 27 15 00-05, and Section 27 15 00 Communications Horizontal Cabling. 2. Point-of-Sale (POS) Support:
AT&T Switched Ethernet Service SM
Site Preparation Guide AT&T Switched Ethernet Service SM December 2016 2016 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks
Target Interface / Construction Compliance Inspection Checklist
A. Targets Quantities meet DD9, applicable TC -, and CEHNC Design Guide 0-- Oriented to face firing line or firing positions/points B. Roads-Service, Lanes Number of lanes meets DD 9, applicable TC -,
June
DESIGN CRITERIA 1. Related Sections: Division 1, Section 16000, Design Standards 16600-01 through 16600-07 and Section 16750. 2. Point-of-Sale (POS) Support: A. Abbreviations and Acronyms: 1). ADP Automated
Installation Notes TII Model 341 Protector
Installation Notes TII Model 341 Protector (ATT-IS PEC 32918) for MERLIN Communications System In Range Out of Building (IROB) Station Installation By Trained Technician Only WARNING: Failure to follow
Network Infrastructure Standard. Vanderbilt University - Information Technology Network Services
Network Infrastructure Standard Vanderbilt University - Information Technology Network Services Table of Contents 1. General Project Terms and Conditions. 3 2. Standards and Contractor Qualifications...
Contents. Structured Cabling Solutions. LAN Cables Patch Cords Connectors Patch Panels... 06
Contents Cat6 Structured Cabling Solutions U/UTP Cabling Solutions Structured Cabling Solutions LAN Cables... 03 Patch Cords... 04 Connectors... 05 Patch Panels... 06 U/FTP Cabling Solutions LAN Cables...