TETRA Interoperability Certificate

Transcription

1 TETRA Interoperability Certificate Thales, Digicom25, SwMI PMRS, BHR21 IS, Terminal Elancourt, February 2008 Latest SwMI SW Release: <SwMI Software> Latest Terminal SW Release: PTA_0225 Latest SwMI HW Release: <SwMI Hardware> Latest Terminal HW Release: LA8 ISCOM (Istituto Superiore delle Comunicazioni e delle Tecnologie dell'informazione) certifies, that the Thales, Digicom25, SwMI and the PMRS, BHR21 IS, terminal have been subject to interoperability testing for the certified features listed on second page of this certificate, in accordance with the TETRA Interoperability Profiles, TIP compliance Test Plan and related TETRA interoperability requirement tables. NOTE: The Infrastructure contains EADS TB3 base station and Thales core network. The aim of the test session is to have IOP certification for both brand names Claricor TETRA Solution (EADS) and Digicom25 (Thales). Then for each Terminal two certificates are issued (i.e. one for EADS Claricor TETRA Solution and the other one for Thales Digicom25). See the manufacturers declaration in Annex 1. The table lists all the available TETRA interoperability profiles, and summarizes the main functionalities of every profile according to the TETRA interoperability requirement tables. A feature is when it has been successfully tested during the last test session with one of the testing method described in the TETRA process document part 1 (TPD001). A breakdown into the feature details is given in the Feature Compliance Overview section of this certificate. Detailed test results and explanation about the procedure used to provide verdicts are listed in the Test Report associated to this Certificate. IOP test engineer Radio Office Manager (Ing. ) ISCOM - V.le America 201, Rome, Italy Ph.: , Fax: Date of issue: tetra_ctc.iscom@comunicazioni.it, Web: 1/12

2 features TETRA Tetra Association, TTR001-01: Core Registration Group Management Group call Individual call Status messages Pre-emptive Priority Call Emergency Call Partial Cell Re-selection - PSTN interconnect - MS-ISDN Numbering - In Call Signalling Subscriber Class Procedures - Common Secondary Control Channels - BS Fallback Operation - Energy Economy Mode - Transmit Inhibit - Tetra Association, TTR001-02: SDS SDS Type 1, 2 or 3 - SDS - TL Tetra Association, TTR : DGNA Support for individually addressed DGNA Partial Support for group addressed DGNA - Tolerance of unsupported DGNA functions - Tetra Association, TTR : Auth SwMI Initiated (non-mutual) Authentication SwMI Initiated Authentication made Mutual by MS - TEI Query - 2/12

3 Feature Compliance Overview The first pages of this certificate provide an indication about the main interoperable TETRA features for each TIP specification (as described in the TIC-RT). The main interoperable TETRA features results depend on a set of sub-feature, the verdicts associated to each sub-feature are directly derived from the analysis of the performed test cases. The results associated to each feature and sub-feature are shown in the Feature compliance report table below. The main features are indicated with grey background and the associated sub-features (or second level features) have white background. The verdict assigned to a sub-feature as showed on Page 2, is derived by the Feature compliance report tables. Partial Verdict Definition All required tests have been performed and passed. Not all the required test cases have been performed, but none have failed. - Feature cannot be certified e.g. it is not supported by at least one product, no tests were performed, or some tests were performed but at least one failed. The verdict assigned to a sub-feature is the result of the analysis of the test case results listed in the Test Report. The verdict assigned to each sub-feature is derived from one or several test case results or test steps result, the TETRA Interoperability requirement tables (TIC-RTs) indicate the link between sub-features and test cases for the certified set of equipment capabilities (see Test Report). Verdict Passed (note x) Time_limited Definition All mandated tests or steps of tests linked to this functionality (as per TIC-RT indication) are compliant with the TIP specification relevant to this feature. A note can be associated to this result if further clarification on the behaviour of the equipment is needed. Not all Mandated tests (as per TIC-RT indication) have been executed (ran out of time) The verdict associated to the feature gives also indication about the method used to test that feature. The allowed testing Methods are listed in the table below, a complete description of the procedures and constraints associated to each of them can be found in the TPD001 TETRA Interoperability Certification Process Description document. Testing Method Spot Regression Regression on spot Description All mandated tests associated to the feature have been executed. Only a selection of the mandatory test cases associated to the feature has been executed during the test session. These tests are a subset of the tests performed on an equivalent software which has been completely tested against the same functionality on a different equipment, see manufacturer declaration in annex A. Only a selection of the mandatory the test cases associated to the feature is executed during the test session. These tests are a subset of the tests performed on a previous version of the same software which has been complete tested in a previous test session against the same functionality, see manufacturer declaration in annex A. The regression method has been applied on the verdicts based on the spot testing method. 3/12

4 Depending on equipment capabilities declared by the manufacturer, some features or sub-feature cannot be tested. The following table describes meaning of the used abbreviation: Indication Definition The SwMI and MS do not support the minimum features required to verify these items The SwMI does not support the minimum features required to verify these items The MS does not support the minimum features required to verify these items ISCOM has made every effort to ensure that every result have been correctly evaluated in accordance with the relevant TIPs, Test Plans and TIC-RTs. ISCOM has no liability for the test results, or towards the manufacturers. The table on the following page lists HW and SW releases of SwMI and Terminal under test in the last four test sessions and the used TIP specifications, Test Plans, and TIC-RTs. This Certificate and Certificates from previous test sessions are available on the TETRA Association web site ( The feature results are shown in the tables below. 4/12

5 Information on equipment under test and document references Test Session Date/Place SwMI Type SwMI HW Release SwMI SW Release Terminal Type Terminal HW release Terminal SW release TIP Specs and TIP Compliance Test Plans Core SDS DGNA Auth Thales, Elancourt, February 2008 Digicom25 <SwMI Hardware> <SwMI Software> BHR21 IS LA8 PTA_0225 TTR v500 IOP v260 TIC-RT v231 TTR v201 IOP v200 TIC-RT v202 TTR v200 IOP v201 TIC-RT v211 TTR v300 IOP v200 TIC-RT v213 5/12

6 Feature compliance report Registration ITSI attach Test Session SwMI initiated location updating LA timer based Periodic location updating De-registration Group Management Single group attachment Multiple group attachment MS initiated group detachment SwMI initiated group management Group call Normal group call Late entry Priority Group scanning TTR Core Thales Elancourt February _pass_of_5 5_pass_of_5 8_pass_of_8 3_pass_of_3 6/12

7 Call setup modifications TETRA Resource Queuing based on Call Priority Individual call Simplex individual call Duplex individual call Call setup modifications Resource Queuing based on Call Priority Indication of imminent call disconnection Status messages Individual addressed Status transfer Group addressed Status transfer Pre-emptive Priority Call Pre-emption of Resources Pre-emption of Busy Users Emergency Call Pre-emption of Resources Pre-emption of Busy Users Call setup modifications Cell Re-selection 9_pass_of_10 4_pass_of_4 1_pass_of_2 4_pass_of_4 3_pass_of_3 FAILED 6_pass_of_15 7/12

8 Undeclared Unannounced TETRA Announced - with Call Restoration Announced - without Call Restoration PSTN interconnect TETRA Originated Call PSTN Originated Call DTMF over-dial MS-ISDN Numbering MS ISDN - Voice Call MS-ISDN Status In Call Signalling Slow Signalling on Traffic Channel (SACCH) Fast Signalling on Traffic Channel (FACCH) Subscriber Class Procedures Cell Selection based on Subscriber Class FAILED 3_pass_of_7 FAILED 2_pass_of_7 No_Equipment 0_pass_of_4 No_Equipment 0_pass_of_3 No_Equipment 0_pass_of_1 Subscriber Class Delivery during Location Update Use of Preferred Subscriber Classes Common Secondary Control Channels One C-SCCH per cell Two C-SCCH per cell Three C-SCCH per cell BS Fallback Operation Switch to/from BS Fallback Operation Roaming with BS Fallback Operation Services with BS Fallback Operation Energy Economy Mode Energy Economy Mode Operation 8/12

9 Transmit Inhibit TETRA TXI Activation & De-Activation without Status message TXI Activation & De-Activation with Status message Receipt of group addressed service during TXI 9/12

10 TTR Short Data Service SDS Type 1, 2 or 3 SDS Type 1 SDS Type 2 SDS Type 3 SDS-TL Individually Addressed Group Addressed Using MS-ISDN dialling Using UCS2 coding scheme 3_pass_of_3 TTR Dynamic Group Number Assignment Support for individually addressed DGNA Support for individually addressed DGNA assignment without attachment Support for individually addressed DGNA assignment with attachment as selected group Support for individually addressed DGNA assignment with attachment as scanned group Support for individually addressed DGNA assignment with rejected attachment Support for individually addressed assigment for pre-programmed group No_Equipment 5_pass_of_9 No_Equipment 2_pass_of_4 3_pass_of_3 No_Equipment 2_pass_of_5 Support for group addressed DGNA Support for group addressed DGNA assignment Management of 'group assignment lifetime' Support for group addressed DGNA deassignment Tolerance of unsupported DGNA functions MS tolerance of unsupported individual addressed DGNA signalling MS tolerance of unsupported group addressed DGNA signalling 10/12

11 SwMI Initiated (non-mutual) Authentication Attach with authentication Roaming with authentication SwMI rejects MS during authentication MS rejects SwMI during authentication TTR Authentication SwMI Initiated Authentication made Mutual by MS Attach with authentication Roaming with authentication TEI Query TEI Query Operation 11/12

12 Annex 1: Declarations 12/12