SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE

Transcription

1 ANSHAN YES OPTOELECTRONICS DISPLAY CO.,LTD SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE MODEL NO. YTS35ELAB-- DATE DEC. 2, 27 Approved Checked Department CUSTOMER MODEL NO. DATE Approved Checked Department ADD 25# QIANSHAN ROAD,ANSHAN LIAONING P.R.CHINA TEL FAX P.C

2 YTS35ELAB-- Revision Revision Description Date 2 of 22

3 YTS35ELAB--. General Description and Features YTS35ELAB-- is a 3.5 TFT-LCD MODULE dedicated for video.the TFT-LCD will be applied to a high transmittance mode TFT-LCD product. TN mode This product is composed of a TFT LCD panel, driver ICs, FPC and a backlight unit. The following table described the features of YTS35ELAB--. No. Item Screen Size Specification 3.5 inch Remark Diagonal 2 Display Resolution 32 x RGB x 24 Dot 3 Module Size 77.8 (H) x 64.5 (V) x 2.8 (D) 4 Dot Pitch.73 (H) x.29 (V) mm 5 Active Area 7.8 (H) x (V) mm 6 Display Mode Normally white/transmissive 7 Pixel Arrangement RGB-Strip 8 Display Color 6M 9 Viewing Direction 2o cloc Input Interface digital 24-bits RGB 2 32 R G B R G B 2 R G B DISPLAY 24 R G B R G B DOT PITCH (V) DOT PITCH (H) Pixel Arrangement 3 of 22

4 PRODUCT SPECIFICATIO 2. Functional Block Diagram YTS35ELAB-- 4 of 22

5 3. Electrical Specifications YTS35ELAB Pin Description Pin Symbol I/O Function Remark K I Backlight LED Ground 2 K I Backlight LED Ground 3 A I Backlight LED Power 4 A I Backlight LED Power 5 NC - Not Use 6 NC - Not Use 7 NC O Not Use 8 /RESET I Hardware Reset 9 /CS I Chip select pin of serial interface SCL I Clock pin of serial interface SDI I Data input pin in serial mode 2 BB I Blue Data Bit 3 BB I Blue Data Bit 4 BB2 I Blue Data Bit 2 5 BB3 I Blue Data Bit 3 6 BB I Blue Data Bit 4 7 BB5 I Blue Data Bit 5 8 BB6 I Blue Data Bit 6 9 BB7 I Blue Data Bit 7 2 GG I Green Data Bit 2 GG I Green Data Bit 22 GG2 I Green Data Bit2 23 GG3 I Green Data Bit3 24 GG4 I Green Data Bit4 25 GG5 I Green Data Bit5 26 GG6 I Green Data Bit6 5 of 22

6 YTS35ELAB-- 27 GG7 I Green Data Bit7 28 RR I Red Data Bit 29 RR I Red Data Bit 3 RR2 I Red Data Bit2 3 RR3 I Red Data Bit3 32 RR4 I Red Data Bit4 33 RR5 I Red Data Bit5 34 RR6 I Red Data Bit6 35 RR7 I Red Data Bit7 36 HSYNC I Line synchronization signal 37 VSYNC I Frame synchronization signal 38 DOTCLK I Dot-clock signal and oscillator source 39 NC - Not Use 4 NC - Not Use 4 VDD I Logic Power 42 VDD I Logic Power 43 NC - Not Use 44 NC - Not Use 45 NC - Not Use 46 NC - Not Use 47 NC - Not Use 48 NC - Not Use 49 NC - Not Use 5 NC - Not Use 5 NC - Not Use 52 ENABLE I Data Enable Input 53 GND I Ground 54 GND I Ground 6 of 22

7 YTS35ELAB-- Basic Display Color and Gray Scale Input Color Data Red MSB LSB Green MSB LSB Blue MSB LSB Color R7 R6 R5 R4 R3 R2 R R G7 G6 G5 G4 G3 G2 G G B7 B6 B5 B4 B3 B2 B B Basic Colors Black Red(255) reen(255) Blue(255) Cyan Magenta Yellow White Red Red() Dark Red() Red(2) Red(253) Red(254) Red(255) Bright Green Green() Dark Green() Green(2) Green(253) Green(254) Green(255)Bright Blue Blue() Dark Blue() Blue(2) Blue(253) Blue(254) Blue(255) Bright 7 of22

8 YTS35ELAB Absolute Maximum Ratings If the operating condition exceeds the following absolute maximum ratings, the TFT LCD module may be damaged permanently. Item Power voltage Input signal current LED Reverse Voltage LED Forward Current LEDPower Dissipation Storage Temperature Operating Temperature VGH Symbol Values Min Typ Max Unit Condition VDD V AVSS= VDDIO V AVSS= VCI 2.5or AVSS=, V VDDIO NOTE 4Xbooster % NOTE2 5Xbooster % 6Xbooster % VGL -VGH V Isleep μa Idp - 2 ma Vr V If=2*2mA If - 2*2 - ma Pd.384 w If=2*2 ma Ts -3-8 Top -2-7 Note. VCIX2 efficiency=vcix2/(2xvci)x% 2. VGH efficiency=vgh/(vcixn)x%(wher n=booster factor) 8 of 22

9 YTS35ELAB Electrical Characteristics 3.4. TFT-LCD Panel (GND =V) Note. VcomH& VcomLAdjust the color with gamma data. Item Symbol Specification Min Typ Max Unit TFT gate on voltage VGH V TFT gate off voltage VGL - V TFT common VCOMH 2.5 (3.6) 4.5 V electrode voltage VCOML -3 (-2.4) V NOTE. Vcom must be adjusted to optimize display qualitycross talk,contrast ratio and etc. 2. VGH is TFT gate operating voltage 3. VGL is TFT gate operating voltage The storage capacitance structure of this product is Cst(Storage on Common) The low voltage level of VGL signal must be fluctuated with same phase as Vcom,in case of storage on Gate structure 4. Environmental condition25±5 9 of 22

10 YTS35ELAB Backlight Unit (GND =V) ITEM SYMBOL MIN TYP MAX NUIT CONDITIONS Forward Voltage Vf V If=2*2mA Forward Current If - 2*2 - ma Power Dissipation Pd.384 W If=2*2mA Reverse Voltage VR V Luminous Intensity IV 28 3 Cd/m 2 If=2*2mA Luminous Intensity 25 Cd/m (LCD surface) 2 If=2*2mA Luminous 75 8 % Uniformity Chromaticity X=.27 X=.33 If=2mA Ta=25 coordinate X=.27 X=.33 Each chip ITEM SYMBOL RATINGS Operating Temperature Range Topr -3 to +7 Storage Temperature Range Tsty -4 to +85 D A B C E A P Q R F J I H G K A N L M O of 22

11 YTS35ELAB AC Timing AC Timing Characteristics. AC Timing Diagrams of 22

12 3.4.4 SPI Timing PRODUCT SPECIFICATION YTS35ELAB-- 2 of 22

13 YTS35ELAB interface 3 of22

14 3.4.6 power Up sequence PRODUCT SPECIFICATION YTS35ELAB-- 4 of 22

15 YTS35ELAB power Down sequence 5 of 22

16 YTS35ELAB Power Sequence The LCD panel adopts high voltage driver ICs, so it could be permanently damaged if a wrong power on/off sequence is used. When powering on the LCD, VCC should go up firstly, and then turn on VGL and VDD, and finally VGH. Turn off the LCD panel with reversed order or shut off all the power supplies simultaneously. 6 of 22

17 YTS35ELAB-- 4. Optical Specifications The following items are measured under stable conditions. The optical characteristics should be measured in dark room or equivalent state with the methods shown in Note. Item Symbol Conditions Specifications Min Typ Max Unit Transmittance T% % Contrast Ratio CR Response Time TR 5 3 Ms TC 35 5 ms XR Viewing Red normal YR angle XG Green Chromaticity YG θ X = θy = Blue XB YB White XW YW Viewing Angle Note Hor. Ver. θx+ 45 θx- Center 45 θy+ 5 θy- CR 35 Deg.. Definition of Contrast Ratio(CR) The contrast ratio can be calculated by the following expression Contrast Ratio(CR)=L63/L L63Luminance of gray level 63 LLuminance of gray level CR=CR() CR(X) is corresponding to the Contrast Ratio of the point Xat Figure in Note(5) 2. Definition of response time(fr,tf) Note All left side data arebased on CMO S following condition-t6 NTSC6% LC59 LightC light (MachineBM5A) Normal Polarizer Without DBEF Simulation Data Reference Only" 7 of 22

18 YTS35ELAB-- 3.Definition of Viewing Angle ***The abov Viewing Angle is the measuring position with Largest Contrast Ratio;not for good image quality.view Direction for good image quality is 2O clock.module maker can increase the Viewing Angle by applying wide View Film. 4.measurement Set-Up The LCD module should be stabilized at a given temperature for 2 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance,the measurement should be executed after lighting Backlight for 2 minutes in a windless room. 8 of 22

19 YTS35ELAB-- 5. Initial code LCD Initial_HX8238 COMMAND CODE DESCRIPTION RH 633f Driver Output Control R2H 2 LCD-Driving-Waveform Control R3H 7664 Power control R4H 447 Input Data and Color Filter Control R5H 42 Function Control RAH 48 Contrast/Brightness Control RBH D4 Frame Cycle Control RDH 23A Power control 2 REH 2CC Power control 3 RFH Gate Scan Position R6H 9F8 Horizontal Porch R7H 222 Vertical Porch REH DD Power control 4 Adjust the Gamma Curve COMMAND CODE DESCRIPTION R3H 57 Gamma Control R3H 4 Gamma Control R32H 77 Gamma Control R33H Gamma Control R34H Gamma Control R35H 37 Gamma Control R36H 7 Gamma Control R37H Gamma Control R3AH 4B Gamma Control R3BH 4B Gamma Control 9 of 22

20 YTS35ELAB-- 6. Mechanical Dimensions 2of 22

21 YTS35ELAB-- 7. Reliability Test Items Test Item Test Condition High Temperature Operation High Temperature and High Humidity Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Thermal Shock 6 for 24 hours 6, 9%RH for 24 hours -2 for 24 hours 8 for 24 hours -3 for 24 hours -25 (.5Hr) ~ +7 (.5Hr) for 2 cycles Shock Level G Mechanical Shock Waveform Half Sinusoidal Wave Shock Time 6ms Number of Shocks 3 times for each ±X, ±Y, ±Z direction Vibration Sweep Hz ~ 55Hz Amplitude.5mm Sweep time min The Period 6 cycle for each direction of X,Y,Z Note. The test samples have recovery time for 2 hours at room temperature before the function check. In the standard conditions, there is no display function NG issue occurred. 2. All the cosmetic specifications are judged before the reliability stress. 2of 22

22 8. Handling Precautions YTS35ELAB Safety The liquid crystal in the LCD is poisonous. Keep away from your mouth and eyes. If the liquid crystal contacts with your skin, mouth or clothes, use soap to wash it off immediately Handling i. The LCD panel is made by thin glass. Prevent the panel from mechanical shock or putting excessive force on its surface. ii. The polarizer attached on the display is very easy to be damaged, handle it with special attention. iii. To avoid contamination on the display surface, do not touch the display surface with bare hands. iv. The transparent electrodes may be disconnected if you use the LCD panel under dew-condensing environment. v. The characteristics of the semiconductor devices may be affected when they are exposed to light, possibly resulting in malfunctioning of the ICs. To prevent such malfunctioning of the ICs, the application design and the mounting layout are done so that the IC is not exposed to light in using Static Electricity Ground soldering iron tips, tools and testers when you operate. Also ground your body when handling the products and store the products in an anti-electrostatic container Storage Store the products in a dark place where the temperature is within the range of 25± and with low humidity (65%RH or less). Do not store the LCD product in an atmosphere containing organic solvents or corrosive gases Cleaning Do not wipe the polarizer with dry cloth, as it might cause scratch. Wipe the polarizer with a soft cloth soaked with petroleum IPA, other chemical might damage. 22 of 22