MODEL NO.: G121S1-L02

Size: px

Start display at page:

Download "MODEL NO.: G121S1-L02"

Aleesha Houston
5 years ago
Views:

1 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 TFT LCD Specification MODEL NO. G2S-L2 Customer Approved by Note FOR MORE INFORMATION AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA Http// Liquid Crystal Display Division QRA Division. APPL Head Division. / 29 Version 2.

2 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 - CONTENTS - REVISION HISTORY GENERAL DESCRIPTION OVERVIEW.2 FEATURES.3 APPLICATION.4 GENERAL SPECIFICATIONS.5 MECHANICAL SPECIFICATIONS 2. ABSOLUTE MAXIMUM RATINGS ABSOLUTE RATINGS OF ENVIRONMENT 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2. TFT LCD MODULE LED CONVERTER 3. ELECTRICAL CHARACTERISTICS TFT LCD MODULE 3.2 BACKLIGHT UNIT 4. BLOCK DIAGRAM TFT LCD MODULE 5. INPUT TERMINAL PIN ASSIGNMENT TFT LCD MODULE 5.2 BACKLIGHT UNIT 5.3 COLOR DATA INPUT ASSIGNMENT 6. INTERFACE TIMING INPUT SIGNAL TIMING SPECIFICATIONS 6.2 POWER ON/OFF SEQUENCE 6.3 THE INPUT DATA FORMAT 6.4 SCANNING DIRECTION 7. OPTICAL CHARACTERISTICS TEST CONDITIONS 7.2 OPTICAL SPECIFICATIONS 8. RELIABILITY TEST CRITERIA PACKAGING PACKING SPECIFICATIONS 9.2 PACKING METHOD. DEFINITION OF LABELS PRECAUTIONS ASSEMBLY AND HANDLING PRECAUTIONS.2 SAFETY PRECAUTIONS 2. MECHANICAL CHARACTERISTICS / 29 Version 2.

3 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 REVISION HISTORY Version Date Section Description 2. Jan., 2 All G2S-L2 Spec. was first issued. 3 / 29 Version 2.

4 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2. GENERAL DESCRIPTION. OVERVIEW The G2S-L2 model is a 2. TFT-LCD module with a white LED Backlight Unit and a 2-pin ch-lvds interface. This module supports 8 x 6 SVGA MVA mode and displays 262K/ 6.2M colors. The converter for the LED Backlight Unit is built in..2 FEATURES - Wide viewing angle - High contrast ratio - SVGA (8 x 6 pixels) resolution - Wide operating temperature - DE (Data Enable) mode - LVDS (Low Voltage Differential Signaling) interface - Reversible-scan direction - RoHS Compliance - LED Light Bar Replaceable.3 APPLICATION - TFT LCD Monitor - Industrial Application - Amusement.4 GENERAL SPECIFICATINS Item Specification Unit Note Diagonal Size 2. inch Active Area 246.(H) x 84.5(V) mm () Bezel Opening Area 249.(H) x 87.5(V) mm Driver Element a-si TFT active matrix - - Pixel Number 8 x R.G.B. x 6 pixel - Pixel Pitch.375(H) x.375(v) mm - Pixel Arrangement RGB vertical stripe - - Display Colors 262K/ 6.2M color - Transmissive Mode Normally black - - Surface Treatment Hard coating (3H), Anti-glare (Haze 25%) - - Module Power Consumption 3.52 W (3),Typ. 4 / 29 Version 2.

5 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2.5 MECHANICAL SPECIFICATIONS Item Min. Typ. Max. Unit Note Horizontal (H) mm Module Size Vertical (V) mm () Depth (D) mm Weight g - The mounting inclination of the connector makes - (2) the screen center within ±.5mm as the horizontal. I/F connector mounting position Note () Please refer to the attached drawings for more information of front and back outline dimensions. (2) Connector mounting position +/-.5mm (3) The Module Power Consumption is specified at 3.3V, white pattern and % duty for LED backlight. 5 / 29 Version 2.

6 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 2. ABSOLUTE MAXIMUM RATINGS 2. ABSOLUTE RATINGS OF ENVIRONMENT Item Symbol Value Min. Max. Unit Operating Ambient Temperature T OP ºC Storage Temperature T ST ºC Note () Temperature and relative humidity range is shown in the figure below. (2) 9 %RH Max. (Ta 4 ºC). (3) Wet-bulb temperature should be 39 ºC Max. (Ta > 4 ºC). (4) No condensation. Note Relative Humidity (%RH) Operating Range 4 2 Storage Range Temperature (ºC) 6 / 29 Version 2.

7 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2. TFT LCD MODULE Value Item Symbol Unit Note Min. Max. Power Supply Voltage VCC V () LED CONVERTER Item Symbol Value Min. Max. Unit Note Converter Voltage V i V (), (2) Enable Voltage EN V Backlight Adjust ADJ V Note () Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for lamp (Refer to 3.2 for further information). 7 / 29 Version 2.

8 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 3. ELECTRICAL CHARACTERISTICS 3. TFT LCD MODULE Ta = 25 ± 2 ºC Parameter Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage VCC V at VCC=3.3V V at VCC=5.V Rush Current I RUSH A (2), at VCC=5.V Power Supply Current ma (3)a, at VCC=3.3V, 6Hz White ma (3)a, at VCC=5.V, 6Hz ma (3)b, at VCC=3.3V, 6Hz Black ma (3)b, at VCC=5.V, 6Hz Power Consumption P L W VCC=3.3V, 6Hz, White Pattern LVDS differential input voltage VID mv - LVDS common input voltage VICM V - Note () The module is recommended to operate within specification ranges listed above for normal function. Note (2) Measurement Conditions +3.3V Q 2SK475 FUSE C3 Vcc (LCD Module Input) R uf 47K (High to Low) (Control Signal) SW +2V R2 K Q2 2SK47 VR 47K C2 C.uF uf Vcc rising time is 47µs +3.3V.9Vcc.Vcc GND 47µs 8 / 29 Version 2.

9 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 Note (3) The specified power supply current is under the conditions at Ta = 25 ± 2 ºC, f v = 6 Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern Active Area Active Area 9 / 29 Version 2.

10 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 3.2 LED CONVERTER Ta = 25 ± 2 ºC Parameter Symbol Value Min. Typ. Max. Unit Note Converter Power Supply Voltage V i V (Duty %) Converter Power Supply Current I i Vi = 2V (Duty %) Converter Power Consumption Pi Vi = 2V (Duty %) EN Control Level Backlight on V Backlight off V PWM Control Level PWM High Level V PWM Low Level V PWM Control Duty Ratio 2 % PWM Control Frequency f PWM Hz LED Life Time L L 5, Hrs (2) Note () LED current is measured by utilizing a high frequency current meter as shown below Note (2) The lifetime of LED is defined as the time when it continues to operate under the conditions at Ta = 25 ±2 and I LED = 8mA DC (LED forward current) until the brightness becomes 5% of its original value. Input Power Pi Power Supply Vi, Ii GND Converter LED Backlight Unit / 29 Version 2.

11 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 4. BLOCK DIAGRAM 4. TFT LCD MODULE RX3(+/-) SEL6/8 RXC(+/-) RX2(+/-) VCC VCC INPUT CONNECTOR (STARCONN 76B2-48RA-G4 or JAE-FI-SEB2P-HFE) LVDS INPUT / TIMING CONTROLLER DC/DC CONVERTER & REFERENCE VOLTAGE SCAN DRIVER IC TFT LCD PANEL (8x R.G.B.x6) DATA DRIVER IC Vi CONVERTER CONNECTOR (Connector, 928-,.mm, WTB, pin, Aces) LED Converter LED BACKLIGHT UNIT / 29 Version 2.

12 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 5. INPUT TERMINAL PIN ASSIGNMENT 5. TFT LCD MODULE Pin Name Description Remark RX3+ Differential Data Input, CH3 ( Positive ) 2 RX3- Differential Data Input, CH3 (Negative ) 3 GND GND LVDS 6/8 bit select function control, Note ( 3 ) 4 SEL68 Low or NC 6 bit Input Mode High 8bit Input Mode 5 GND Ground 6 RXC+ Differential Clock Input ( Positive ) LVDS Level Clock 7 RXC- Differential Clock Input ( Negative ) 8 GND Ground 9 RX2+ Differential Data Input, CH2 ( Positive ) RX2- Differential Data Input, CH2 ( Negative ) GND Ground 2 RX+ Differential Data Input, CH ( Positive ) 3 RX- Differential Data Input, CH ( Negative ) 4 GND Ground 5 RX+ Differential Data Input, CH ( Positive ) 6 RX- Differential Data Input, CH (Negative ) Horizontal Reverse Scan Control, Note ( 3 ) 7 relr Low or NC Normal Mode. High Horizontal Reverse Scan 8 reud Vertical Reverse Scan Control, Low or NC Normal Mode, Note ( 3 ) 9 VCC Power supply 2 VCC Power supply High Vertical Reverse Scan Note () Connector Part No. FI-SEB2P-HFE(JAE) or 76B2-48RA-G4(STARCONN) or equivalent. Note (2) User s connector Part No. FI-SE2ME(JAE) or equivalent Note (3) Low stands for V. High stands for 3.3V. NC stands for No Connected. 5.2 LED CONVERTER Pin Symbol Description Remark V i Converter input voltage 2V 2 V i Converter input voltage 2V 3 V i Converter input voltage 2V 4 V i Converter input voltage 2V 5 V GND Converter ground Ground 6 V GND Converter ground Ground 7 V GND Converter ground Ground 8 V GND Converter ground Ground 9 EN Enable pin 3.3V PWM Dimming ADJ Backlight Adjust (9-2Hz, Hi 3.3V DC, Lo V DC ) Note () Connector Part No H(ACES) or equivalent Note (2) User s connector Part No. 929-(ACES) or equivalent 2 / 29 Version 2.

13 Issued Date Jan., 2 Model No. G2S-L2 3 / 29 Version COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R5 R4 R3 R2 R R G5 G4 G3 G2 G G B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red()/Dark Red() Red(2) Red(6) Red(62) Red(63) Gray Scale Of Green Green()/Dark Green() Green(2) Green(6) Green(62) Green(63) Gray Scale Of Blue Blue()/Dark Blue() Blue(2) Blue(6) Blue(62) Blue(63) Note () Low Level Voltage, High Level Voltage Datasheet pdf - http//

14 Issued Date Jan., 2 Model No. G2S-L2 4 / 29 Version 2. The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R7 R6 R5 R4 R3 R2 R R G7 G6 G5 G4 G3 G2 G G B7 B6 B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red() / Dark Red() Red(2) Red(253) Red(254) Red(255) Gray Scale Of Green Green()/ Dark Green() Green(2) Green(253) Green(254) Green(255) Gray Scale Of Blue Blue() / Dark Blue() Blue(2) Blue(253) Blue(254) Blue(255) Note Low Level Voltage, High Level Voltage Datasheet pdf - http//

15 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 6. INTERFACE TIMING 6. INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note DCLK Frequency Fc MHz Total Tv Th Tv=Tvd+Tvb Vertical Active Display Term Display Tvd Th Blank Tvb Tv-Tvd 28 Tv-Tvd Th Total Th Tc Th=Thd+Thb Horizontal Active Display Term Display Thd Tc Blank Thb Th-Thd 256 Th-Thd Tc Note () Because this module is operated by DE only mode, Hsync and Vsync input signals should be set to low logic level or ground. Otherwise, this module would operate abnormally. (2) Frame rate is 6Hz INPUT SIGNAL TIMING DIAGRAM 5 / 29 Version 2.

16 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 6.2 POWER ON/OFF SEQUENCE To prevent a latch-up or DC operation of LCD module, the power on/off sequence should follow the conditions shown in the following diagram..9vcc.9vcc.vcc VCC LVDS T T2 VALID 9% % T3 T7.VCC T4.9Vi.9Vi Vi.Vi.Vi T5 T6 9% BL ON/OFF % T8 T9 PWM DIMMING 9% % Power ON/OFF sequence Note () Please avoid floating state of interface signal at invalid period. Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD VCC to V. Note (3) The Backlight converter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight converter power must be turned off before the power supply for the logic and the interface signal is invalid. Parameter Value Min Typ Max Units T ms T ms T ms T ms T ms T ms T ms T ms T ms 6 / 29 Version 2.

17 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 6.3 The INPUT DATA FORMAT Note () R/G/B data 7 MSB, R/G/B data LSB Note (2) Please follow PSWG Note (3) Output signals from any system shall be low or Hi-Z state when VCC is off 7 / 29 Version 2.

Datasheet pdf - http//www.datasheet4u.net/ Issued Date Jan., 2 Model No. G2S-L2 6.4 SCANNING DIRECTION The following figures show the image see from the front view.

18 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 6.4 SCANNING DIRECTION The following figures show the image see from the front view. The arrow indicates the direction of scan. Fig. Normal Scan Fig.2 Reverse Scan Fig.3 Reverse Scan Fig.4 Reverse Scan Fig. Normal scan ( pin 7, relr = Low or NC, pin 8, reud = Low or NC ) Fig. 2 Reverse scan ( pin 7, relr = High, pin 8, reud = Low or NC ) Fig. 3 Reverse scan ( pin 7, relr = Low or NC, pin 8, reud = High ) Fig. 4 Reverse scan ( pin 7, relr = High, pin 8, reud = High ) 8 / 29 Version 2.

19 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 7. OPTICAL CHARACTERISTICS 7. TEST CONDITIONS Item Symbol Value Unit Ambient Temperature Ta 25±2 o C Ambient Humidity Ha 5± %RH Supply Voltage V CC 3.3 V Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS" Converter Voltage V in 2 V Converter Duty % 7.2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown in 7.2. The following items should be measured under the test conditions described in 7. and stable environment shown in Note (5). Item Symbol Condition Min. Typ. Max. Unit Note Red Rx.6 - Ry Green Color Gy Typ Typ + - Chromaticity Bx θ x =, θ Y = Blue By CS Gx (), (5) White Wx.33 - Wy Center Luminance of White L C (4), (5) Contrast Ratio CR (2), (5) Response Time T R ms θ x =, θ Y = T F ms (3) White Variation δw θ x =, θ Y = (5), (6) Viewing Angle θ x Horizontal θ x CR θ Y Vertical θ Y Deg. (), (5) 9 / 29 Version 2.

20 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 Note () Definition of Viewing Angle (θx, θy) Normal θx = θy = º θy- θy+ θx- = 9º x- θx θx+ y+ 2 o clock direction θy+ = 9º 6 o clock θy- = 9º y- x+ θx+ = 9º Note (2) Definition of Contrast Ratio, CR The contrast ratio can be calculated by the following expression. Contrast Ratio, CR = L63 (255) / L L63 Luminance of gray level 63 (255) L Luminance of gray level CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6). Note (3) Definition of Response Time (T R, T F ) and measurement method % 9% Gray Level 63 (255) Gray Level 63 (255) Optical Response % Gray Level % Time T F T R ms ms 2 / 29 Version 2.

21 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 Note (4) Definition of Luminance of White, L C Measure the luminance of gray level 63 (255) at center point L C = L (5) L (x) is corresponding to the luminance of the point X at Figure in Note (6). Note (5) Measurement Setup The LCD module should be stabilized at given temperature for 2 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 2 minutes in a windless room. LCD Module LCD Panel USB2 CS-2T Center of the Screen 5 mm Light Shield Room (Ambient Luminance < 2 lux) 2 / 29 Version 2.

22 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 Note (6) Definition of White Variation (δw) Measure the luminance of gray level 63 (255) at 5 points δw = Maximum [L (), L (2), L (3), L (4), L (5)] Minimum [L (), L (2), L (3), L (4), L (5)] Horizontal Line D D/4 D/2 3D/4 Vertical Line W W/4 W/2 3W/ X Test Point X= to 5 Active Area 22 / 29 Version 2.

23 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 8. RELIABILITY TEST CRITERIA Test Item Test Condition Note High Temperature Storage Test 85ºC, 24 hours Low Temperature Storage Test -3ºC, 24 hours Thermal Shock Storage Test -3ºC,.5hour 85,.5hour; hour/cycle,cycles High Temperature Operation Test 8ºC, 24 hours ()(2) Low Temperature Operation Test -3ºC, 24 hours High Temperature & High Humidity Operation Test 6ºC, 9%RH, 24hours Shock (Non-Operating) 2G, 2ms, half sine wave, time for ± X, ± Y, ± Z. (3) Vibration (Non-Operating).5G, ~ 3 Hz, min/cycle, 3 cycles each X, Y, Z (3) Note () There should be no condensation on the surface of panel during test. Note (2) Temperature of panel display surface area should be 85 ºC Max. Note (3) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. Note (4) In the standard conditions, there is no function failure issue occurred. All the cosmetic specification is judged before reliability test. 23 / 29 Version 2.

24 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 9. PACKAGING 9. PACKING SPECIFICATIONS () 6pcs LCD modules / Box (2) Box dimensions 465 (L) X 362 (W) X 34 (H) mm (3) Weight approximately 5Kg (6 modules per box) 9.2 PACKING METHOD () Carton Packing should have no failure in the following reliability test items. Test Item Test Conditions Note Vibration ISTA STANDARD Random, Frequency Range 2 2 Hz Top & Bottom 3 minutes (+Z), min (-Z), Non Operation Right & Left minutes (X) Back & Forth minutes (Y) Dropping Test Angle, 3 Edge, 6 Face, 6 cm Non Operation Figure. 9- Packing method 24 / 29 Version 2.

25 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 Sea / Land Transportation (4ft Container) Air Transportation Figure. 9-2 Packing method 25 / 29 Version 2.

Datasheet pdf - http//www.datasheet4u.net/ Issued Date Jan., 2 Model No. G2S-L2. DEFINITION OF LABELS.

26 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2. DEFINITION OF LABELS. CMO MODULE LABEL The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. CHI MEI OPTOELECTRONICS G2S -L2 Rev.XX E27943 MADE IN TAIWAN X X X X X X X Y M D L N N N N RoHS (a) Model Name G2S -L2 (b) Revision Rev. XX, for example A, C, C2 etc. (c) Serial ID X X X X X X X Y M D X N N N N Serial No. CMO Internal Use Year, Month, Date CMO Internal Use Revision CMO Internal Use Serial ID includes the information as below (a) Manufactured Date Year ~9, for 2~29 Month ~9, A~C, for Jan. ~ Dec. Day ~9, A~Y, for st to 3 st, exclude I, O and U (b) Revision Code cover all the change (c) Serial No. Manufacturing sequence of product 26 / 29 Version 2.

27 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2. PRECAUTIONS. ASSEMBLY AND HANDLING PRECAUTIONS () Do not apply rough force such as bending or twisting to the module during assembly. (2) To assemble or install module into user s system can be only in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) It s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will be damaged. (4) Always follow the correct power sequence when LCD module is connecting and operating. This can prevent damage to the CMOS LSI chips during latch-up. (5) Do not pull the I/F connector in or out while the module is operating. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage LCD module when it is operating. (9) High temperature or humidity may reduce the performance of module. Please store LCD module within the specified storage conditions. () When ambient temperature is lower than ºC may reduce the display quality, the response time will become slowly. () Do not keep same pattern in a long period of time. It may cause image sticking on LCD..2 SAFETY PRECAUTIONS () Do not disassemble the module or insert anything into the Backlight unit. (2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (3) After the module s end of life, it is not harmful in case of normal operation and storage. 27 / 29 Version 2.

28 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 2. MECHANICAL CHARACTERISTICS 28 / 29 Version 2.

29 Datasheet pdf - http// Issued Date Jan., 2 Model No. G2S-L2 29 / 29 Version 2.

LITEMAX LF1236E. Sunlight Readable 12.1 LED Backlight Display ENRICH YOUR VISUAL WORLD... (1st Edition 10/13/06 )

LITEMAX LF1236E. Sunlight Readable 12.1 LED Backlight Display ENRICH YOUR VISUAL WORLD... (1st Edition 10/13/06 ) ENRICH YOUR VISUAL WORLD... Sunlight Readable LCD! TM by LITEMAX Wide Temp LED Backlight LITEMAX LF236E Sunlight Readable 2. LED Backlight Display (st Edition /3/6 ) All information is subject to change