Installation Guide. Versatile Access Power and Integration Enclosures. Trove2M2 - Trove2 enclosure with Altronix/Mercury backplane

Size: px

Start display at page:

Download "Installation Guide. Versatile Access Power and Integration Enclosures. Trove2M2 - Trove2 enclosure with Altronix/Mercury backplane"

Rosanna Carpenter
5 years ago
Views:

1 Versatile Access Power and Integration Enclosures Installation Guide Models Include: Trove2M2 - Trove2 enclosure with / backplane TM2 - / backplane only Trove2V2 - Trove2 enclosure with / backplane TV2 - / backplane only TMV2 - or optional door backplane Rev More than just power.

2 Overview: Trove2M2 or Trove2V2 accommodates various combinations of or boards with or without power supplies and accessories for access systems. Specifications: 19 Gauge grey enclosure with ample knockouts for convenient access. Enclosure Dimensions (H x W x D): x x 6.5 (692.15mm x mm x 165.1mm) Trove2M2 - Trove2 enclosure with TM2 / backplane. Includes: tamper switch, cam lock, lock nuts and mounting hardware. Trove2M2 accommodates a combination of the following: Two (2) eflow3nb, eflow4nb, eflow6nb, eflow102nb or eflow104nb. Four (4) ACM4(CB), ACM8(CB), MOM5, PD4UL(CB), PD8UL(CB). Six (6) MR16IN, MR16OUT. Six (6) EP2500 or. Five (5) MR51e. Two (2) MR50. Trove2V2 - Trove2 enclosure with TV2 / backplane. Includes: tamper switch, cam lock, lock nuts and mounting hardware. Trove2V2 accommodates a combination of the following: Two (2) eflow3nb, eflow4nb, eflow6nb, eflow102nb or eflow104nb. Four (4) ACM4(CB), ACM8(CB), MOM5, PD4UL(CB), PD8UL(CB). Six (6) V1000 or V2000. Backplanes Only: TM2 - / backplane only. Includes: lock nuts and mounting hardware. TV2 - / backplane only. Includes: lock nuts and mounting hardware. Optional Door Backplane: TMV2 - or door backplane only. Includes: lock nuts and mounting hardware. Trove2M2, Trove2V2 Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Remove backplane from enclosure. Do not discard hardware. 2. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure s upper keyholes over the three upper screws, level and secure. Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 10). 3. Mount UL Listed tamper switch (included) (Ademco model 112 or equivalent) at the top of the enclosure. Slide the tamper switch bracket onto the edge of the enclosure approximately 2 from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure. Fig Mount // boards to backplane, refer to pages Hardware: Male/Female Standoff Standoff (Metal or Nylon) 5/16 Pan Head Screw 7/8 Pan Head Screw Lock Nut Honeywell model # 112 Tamper Switch or equivalent (provided) Enclosure to Access Control Panel or U.L. Listed Reporting Device Edge of Enclosure // Enclosure

3 TM2: Configuration of Power Supply and/or Boards 1. Fasten standoffs (provided) to pems that match the hole pattern for Power Supply/Chargers or boards (Fig. 2, pg. 3). Use male/female nylon standoffs for the upper two mounting holes in the board. Use metal standoffs for the bottom mounting holes to provide sufficient grounding for the board. 2. Affix boards to standoffs (Fig. 2, pg. 3) by pressing down the upper mounting holes onto nylon standoffs. Use provided mounting screws to affix the lower mounting holes. Make sure that boards are locked onto standoffs. 3. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided). Fig. 2 Power Supply or Metal Standoff Placement Power Supply or Metal Standoff Placement // Enclosure - 3 -

4 TM2: Configuration of Boards 1. Fasten standoffs (provided) to pems that match the hole pattern for MR16IN or MR16OUT (Fig. 3, pg. 4). Use male/female nylon standoffs only. 2. Affix boards to standoffs (Fig. 3, pg. 4) by pressing down the mounting holes onto nylon standoffs. Make sure that boards are locked onto standoffs. 3. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided). Fig // Enclosure

5 TM2: Configuration of Boards (cont d) 1. Fasten standoffs (provided) to pems that match the hole pattern for EP2500 or (Fig. 4, pg. 5). Use male/female nylon standoffs only. 2. Affix boards to standoffs (Fig. 4, pg. 5) by pressing down the mounting holes onto nylon standoffs. Make sure that boards are locked onto standoffs. 3. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided). Fig. 4 // Enclosure - 5 -

6 TM2: Configuration of Boards (cont d) 1. Fasten standoffs (provided) to pems that match the hole pattern for EP1501 or MR51e (Fig. 5, pg. 6). Use male/female nylon standoffs only. 2. Affix boards to standoffs (Fig. 5, pg. 6) by pressing down the mounting holes onto nylon standoffs. Make sure that boards are locked onto standoffs. 3. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided). Fig. 5 EP1501, MR51e EP1501, MR51e EP1501, MR51e EP1501, MR51e EP1501, MR51e // Enclosure

7 TM2: Configuration of Boards (cont d) 1. Fasten standoffs (provided) to pems that match the hole pattern for MR50 (Fig. 6, pg. 7). Use male/female nylon standoffs only. 2. Affix boards to standoffs (Fig. 6, pg. 7) by pressing down the mounting holes onto nylon standoffs. Make sure that boards are locked onto standoffs. 3. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided). Fig. 6 MR50 MR50 // Enclosure - 7 -

8 TV2: Configuration of Power Supply and/or Boards 1. Fasten standoffs (provided) to pems that match the hole pattern for Power Supply/Chargers or boards (Fig. 7, pg. 8). Use male/female nylon standoffs for the upper two mounting holes in the board. Use metal standoffs for the bottom mounting holes to provide sufficient grounding for the board. 2. Affix boards to standoffs (Fig. 7, pg. 8) by pressing down the upper mounting holes onto nylon standoffs. Use provided mounting screws to affix the lower mounting holes. Make sure that boards are locked onto standoffs. 3. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided). Fig. 7 Power Supply or Metal Standoff Placement Power Supply or Metal Standoff Placement // Enclosure

9 TV2: Configuration of Boards 1. Fasten standoffs (provided) to pems that match the hole pattern for V1000 or V2000 boards (Fig. 8, pg. 9). 2. Mount boards to standoffs (Fig. 8, pg. 9) utilizing 7/8 pan head screws (provided). 3. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided). Fig. 8 // Enclosure - 9 -

10 TMV2: Configuration of Boards 1. Fasten standoffs (provided) to pems that match the hole pattern for MR16IN or MR16OUT (Fig. 9, pg. 10). Use male/female nylon standoffs only. 2. Affix boards to standoffs (Fig. 9, pg. 10) by pressing down the mounting holes onto nylon standoffs. Make sure that boards are locked onto standoffs. 3. Fasten backplane to Trove2 enclosure door utilizing lock nuts (provided). Fig // Enclosure

11 TMV2: Configuration of Boards (cont d) 1. Fasten standoffs (provided) to pems that match the hole pattern for EP2500 or (Fig. 10, pg. 11). Use male/female nylon standoffs only. 2. Affix boards to standoffs (Fig. 10, pg. 11) by pressing down the mounting holes onto nylon standoffs. Make sure that boards are locked onto standoffs. 3. Fasten backplane to Trove2 enclosure door utilizing lock nuts (provided). Fig. 10 // Enclosure

12 TMV2: Configuration of Boards 1. Fasten standoffs (provided) to pems that match the hole pattern for V1000 or V2000 boards (Fig. 11, pg. 12). 2. Mount boards to standoffs (Fig. 11, pg. 12) utilizing 7/8 pan head screws (provided). 3. Fasten backplane to Trove2 enclosure door utilizing lock nuts (provided). Fig // Enclosure

13 TM2 and TV2 Mounting Diagram 7.5 (190.5mm) 19.4 (492.76mm) 7.5 (190.5mm) (633.73mm) ( 3.96mm) 25.4 (645.16mm) (412.62mm) (320.55mm) (320.55mm) (215.77mm) 1.0 (25.4mm) 0.45 (11.43mm) 7.5 (190.5mm) 1.0 (25.4mm) 7.5 (190.5mm) 9.2 (233.68mm) // Enclosure

14 TMV2 Mounting Diagram 18.1 (459.7mm) 13.7 (350mm) 7.4 (188mm) 23.7 (602mm) ( 3.96mm) 0.45 (11.43mm) (52.7mm) 8 (203.2mm) 8.7 (221mm) 8.7 (221mm) (274.8mm) 11.8 (299.7mm) 7.85 (199.39mm) 7.5 (190.5mm) 13.7 (350mm) // Enclosure

15 Notes: // Enclosure

16 Enclosure Dimensions (H x W x D approximate): x x 6.5 (692.15mm x mm x 165.1mm) 2.00 (50.8mm) 5.25 (133.35mm) 3.50 (88.9mm) (546.1mm) 3.50 (88.9mm) 5.25 (133.35mm) 1.25 (31.75mm) (14.29mm) (61.34mm) 1.77 (44.96mm) (17.399mm) Knockouts (28.32mm) (22.479mm) 6.25 (158.75mm) 6.25 (158.75mm) 1.25 (31.75mm) 0.85 (21.59mm) 1.5 (38.1mm) (502.92mm) 2.00 (50.8mm) 6.75 (171.45mm) G (685.8mm) 8.25 (209.54mm) 8.00 (203.2mm) 0.85 (21.59mm) 2.00 (50.8mm) 1.00 (25.4mm) 1.25 (31.75mm) 1.25 (31.75mm) 2.00 (50.8mm) 5.25 (133.35mm) 7.00 (177.79mm) 5.25 (133.35mm) 2.00 (50.8mm) is not responsible for any typographical errors. Product specifications are subject to change without notice th Street, Brooklyn New York USA, , fax: website: info@altronix.com. Made in USA. IITrove2M2/Trove2V2 - Rev F21P MEMBER // Enclosure

Installation Guide Versatile Access Power and Integration Enclosures

Rev. 053116 Installation Guide Versatile Access Power and Integration Enclosures Trove1C1 Trove2CV2 - Trove1 enclosure with - Trove2 enclosure with /CDVI backplane (TC1) /CDVI backplane (TCV2) TC1 TCV2