AQUASMART Room Controller
|
|
- Amie Ramsey
- 5 years ago
- Views:
Transcription
1 LLOYD'S REISTER QUALITY ASSURANE AQUASMART Room ontroller IS O W 42WH 42Y 42JW - 42EL INSTALLATION MANUAL
2 Installation manual This control system only operates with water indoor units of the following type: 42W assette, 42WH/WHE Hi-Wall, 42Y Fan coil, 42JW Satellite and 42EL Aqualia. For installation instructions of this unit, refer to the relevant manuals. ontents age eneral information... 2 hoosing the installation site... 2 Installation... 3 Electrical connections... 4 Room controller configuration... 5/7 Troubleshooting... 7 INSTALLATION FLOW HART Read manual ENLISH Install Room ontroller Wire Room ontroller and unit network onfigure Room ontroller Test System Operate Room ontroller Dimension (mm) B - 1
3 eneral information and choosing the installation site IMORTANT: Read the entire instruction manual before starting the installation. For trouble-free installation, which should be carried out by a qualified installer, follow the installation chart sequence. Follow all current national safety code requirements. In particular ensure that a properly sized and connected ground wire is in place. After installation thoroughly test the system operation and explain all system functions to the owner. Leave this manual with the owner for consultation during future periodic maintenance. Dispose of packaging material in accordance with local requirements. The manufacturer denies any responsibility and warranty shall be void if these installation instructions are not observed. Inspect equipment for damage due to improper transportation or handling: file an immediate claim with the shipping company. Do not install or use damaged units. In case of any malfunctioning turn the unit off, disconnect the mains power sply and contact a qualified service engineer. ower Note that the Room ontroller requires no batteries and is not power stealing. It requires 12 VD to be connected for proper operation, which is easily obtained from the Unit connected to it. The Room ontroller will not operate without this connection. Room ontroller Models roducts that the Room ontroller can interface with 42W ASSETTE 42WH/WHE HI-WALL 42Y FAN OIL 42JW SATELLITE 42EL AQUALIA hoosing the installation site and installation The Room ontroller Location The Room ontroller can be positioned on the unit or fitted to the wall. If the indoor air sensor on the Room ontroller has been selected, it should NOT be mounted: Minimum clearances If fitted to a wall, the Room ontroller must be mounted: In the same area where the unit is located, preferably on an inside partitioning wall. Approximately 1.5 m from floor. On a section of wall without pipes or duct work. lose to a window, on an outside wall, or next to a door leading to the outside. Exposed to direct light and heat from a lamp, sun, fireplace, or other temperature-radiating object which may cause a false reading. lose to or in direct airflow of a heating or cooling sply. In areas with poor air circulation, such as behind a door or in an alcove. Maximum of 150 m of total network wiring. B - 2
4 Installation Mounting WARNIN: Before installing the Room ontroller, turn off all power to the Unit that will sply power to the Room ontroller. Electrical shock can cause personal injury or death. ENLISH Match and connect equipment wires to proper terminals in the connector block. Both power and communication wires must be connected correctly for proper Room ontroller operation. Turn OFF all power to unit. Mounting screws Open the Room ontroller rear mounting base to expose mounting holes. The base can be removed to simplify mounting (snap apart carefully at hinge to separate mounting base from remainder of the Room ontroller). Route the Room ontroller wires through the large hole in the mounting base. Level mounting base against wall (for aesthetic value only the Room ontroller need not be level for proper operation) and mark the wall through the 2 mounting holes. Drill two 5 mm mounting holes in wall where marked. Secure mounting base correctly ( ) to wall with 2 screws and anchors provided, (additional anchoring holes available for more secure mounting if needed) making sure all wires extend through hole in mounting base. Adjust length and routing of each wire to reach the proper terminal in the connector block on the mounting base, with 6 mm of extra wire (strip only 6 mm of insulation from each wire to prevent adjacent wires from shorting together when connected). ush any excess wire into the wall and against mounting base. If the air sensor is being used on the Room ontroller, seal hole in wall to prevent air leaks. Leaks can affect sensor operation. ush the Room ontroller snap hinge to the base. onnection cable onnection cable To indoor unit Rigid V conduit inside ø 30mm min. laster approx 30 mm Room ontroller onnector block B - 3
5 Electrical connections Wiring Room ontroller to the unit WARNIN: Before connecting any wiring to the Room ontroller, turn off all power to the unit that will sply power to the Room ontroller. Electrical shock can cause personal injury or death. The Room ontroller is connected to the unit using the following instructions. Reference Diagram 1 or 2 when making these connections. ower cable and communication connections Room controller to the unit (3 conductor cable). Diagram 1: onnection diagram for the following units: 42W 42WH/WHE 42JW 42EL Diagram 2: onnection diagram for the 42Y unit A Y/ B Wire colours A Brown B Blue Y/ Yellow/green B Y/ A D.. OWER ROUND (SINAL) Room ontroller Unit A Y/ B Wire colours A Brown B Blue Y/ Yellow/green Room ontroller Unit Terminal block in the Room ontroller Terminal block in the unit Window contact (if present) Local Bus; maximum 6 units B Y/ A D.. OWER ROUND (SINAL) Terminal block in the Room ontroller Terminal block in the unit Window contact (if present) Local Bus; maximum 6 units Slacken the terminal screws (D ower), (ROUND) and (SINAL), present on the rear base of the Room ontroller. - (D power) - (round) - (Signal) Make the connections on the terminal block of the Room ontroller as per diagram 2. onnect the other end of the cables to the terminal block of the unit as per diagram 2. ower cable installation is now complete. Slacken the terminal screws (D ower), (ROUND) and (SINAL), present on the rear base of the Room ontroller. - (D power) - (round) - (Signal) Make the connections on the terminal block of the Room ontroller as per diagram 1. onnect the other end of the cables to the terminal block of the unit as per diagram 1. ower cable installation is now complete. Wiring Materials required (splied by installer) 1 small screwdriver 3 x 0,5 mm 2 multiple cables, double insulated. Suggested type: H03VV-F. B - 4
6 Room ontroller configuration ENLISH Access to the configuration menu ress and hold the MODE button for around 5 seconds until 1- appears on the display.. 2- AIR SENSOR SELETION rogram if you want to use the air temperature sensor present in the Room ontroller On or the one present in the units OF. The default setting is OF. To select while in configuration mode: This indicates that the user could set configuration item number 1. ress U botton until 2- is displayed. 1- FAHRENHEIT OR ELSIUS: SELETION Select between Fahrenheit (F) or elsius () operation. Factory default is elsius. To select while in configuration mode: ress the MODE button to change the current selection The onfiguration Option ( 1- ) and the current selection should be displayed. ress the MODE button to alter the current selection. Use either the U o DOWN to change between OF (OFF) and On (ON). 3- UNIT TYE It allows to determine appropriately which unit type is connected to the Room ontroller. Use either the U or DOWN button to change between F or. To select while in UNIT ONFIURATION mode: To move to the next setting, press the U button again and the 2- will be displayed. ress and hold the U and DOWN keys at the same time for around 5 seconds, until -2 appears on the display. ress the DOWN button and the display will change to 1-. ress MODE button to alter the current selection (the - will disappear). B - 5
7 Room ontroller configuration ress either the U or DOWN button until the appropriate number is displayed. lease refer to the following table for proper selection: ress the U or DOWN per passare dalla modalitàbutton to go from the O mode (open) to the mode (closed). Unit type Application Size Selected value Hi-Wall 42WH/WHE All All 1 assette 42W All All 3 Fan oil 42Y Vertical All 4 Fan oil 42Y Horizontal All 5 Above ceiling 42JW All All 5 Above ceiling 42EL All All 5 If your unit is not included in the above models, refer to unit installation manual to determine the selected value. An error in the selected value, causes a malfunction or absent swing of the louver and a bad comfort in the heating mode. To end UNIT ONFIURATION mode do not press any buttons for 10 seconds. 5- BOOSTER HEATIN SELETION (splementary heating) Units fitted with electric heaters can be enabled for the Booster Heating function (splementary heating) This function permits heating using hot water and the electric heaters at the same time. To perform the configuration proceed as follows: ress and hold the U and DOWN keys at the same time for around 5 seconds. 4- WINDOW ONTAT SELETION It is possible to configure the window contact in the NO condition (normally open) or in the N (normally closed) condition. To perform this configuration, proceed as follows: ress U button until -5 is displayed. ress and hold the U and DOWN keys at the same time for around 5 seconds. ress the MODE button to select the mode. ress U button until -4 is displayed. ress the U or DOWN button to go from the OFF mode (Booster Heating not enabled) to the ON mode (Booster Heating enabled). ress the MODE button to select the mode. B - 6
8 Room ontroller configuration, troubleshooting ENLISH 6- SELETIN THE TYE OF ALIATION (2 ipes / 4 ipes) With this selection we choose the type of application: 2 ipes The unit is equipped with just one valve which heats (winter) when splied with hot water and cools (summer) when splied with cold water. 4 ipes The unit is equipped with two valves (hot water valve and a cold water valve). To make the configuration, proceed as follows: ress the MODE button to select the mode. ress and hold the U and DOWN keys at the same time for around 5 seconds. ress the U or DOWN button to go from the 2 (2 pipes) mode to the 4 (4 pipes) mode. ress U button until -6 is displayed. Troubleshooting Symptom ossible ause Things to check Solution No LD display 1) mis-wiring of the 12 volt power to Room ontroller control. 1) Verify that +12V and round are connected to the proper terrminals of the ontroller. Reference Installation wiring section for correct connections After disconnecting the power, correct the wiring problem and re-cycle power. 2) ower not online 1) heck that the units main power is connected. The main control board should be operating normally After verifing the wiring to the Room ontrollerl, re-cycle the unit power. 3) No 12 volts between and of terminal block. 1) heck the installation of the J6 plug on the main control board. After disconnecting the power, correct the wiring problem and re-cycle power. +12 volts applied to Room ontroller at the correct terminals and still does not operate 1) The Room ontroller is damaged. hange the Room ontroller and re-cycle power. B - 7
9 L010123H ALOR SRL Str. rogresului nr , sector 5, Bucurestitel: , fax: ofertare@calor.ro -
33MC -URC Room Controller
33M -UR Room ontroller 40KM 40KMQ 40QN 40QNQ INTALLATION MANUAL This control system only operates with indoor units of the following types: 40KM, 40KMQ assette, 40QN, 40QNQ High Wall For installation instructions
More informationZone Manager INSTALLATION MANUAL 40KMC KMQ QNC QNQ
40KMC------301 40KMQ------301 40QNC------3 40QNQ------3 INSTALLATION MANUAL Installation manual This control system only operates with indoor units of the following models: 40KMC------301 and 40KMQ------301
More informationInstallation, Start-up and Operating Instructions
Installation, Start-up and Operating Instructions EVOLUTION SMART SENSOR FOR ZONING Cancels: NEW II ZONESMS-0-1 7-04 NOTE: Read the entire instruction manual before starting the installation. This symbol
More informationInstallation Instructions
50ES, 50EZ, 50GL, 50GS, 50GX, 50JS, 50JX, 50JZ, 50SD, 50SZ, 50VL, 50VT, 50XP, 50XZ 601A, 602A, 602B, 604A, 604B, 604D, 607C, 701A, 702A, 702B, 704A, 704B, 704D, 707C PA1P, PA2P, PA3P, PH1P, PH2P, PH3P
More informationWireless Remote Controller Kit
INSTALLATION MANUAL Wireless Remote Controller Kit LS BRC4C8 Read these instructions carefully before installation. Keep this manual in a handy place for future reference. This manual should be left with
More informationKNX T-UP. Temperature Sensor. Technical specifications and installation instructions
EN KNX T-UP Temperature Sensor Technical specifications and installation instructions Elsner Elektronik GmbH Control and Automation Engineering Herdweg 7 D 75391 Gechingen Phone +49 (0) 70 56 / 93 97-0
More informationSAVE THESE INSTRUCTIONS
OUTDOOR HARDWIRE INSTALLATION INSTRUCTIONS Please read and save these instructions. Read carefully before using product. Protect yourself and others by observing all safety information, warnings and cautions.
More informationModel HM-535 Power Supply Installation and Service Instructions
Model HM-535 Power Supply Installation and Service Instructions 430-535 0104 2004 Heritage MedCall, Inc SENTRY INSTALLATION & SERVICE INSTRUCTIONS POWER SUPPLY UNIT Model HM-535 IMPORTANT SAFETY INSTRUCTIONS
More informationINSTALLATION INSTRUCTIONS
Wired Remote Controller 7 Day Programmable Ductless Systems KSACN0401AAA (High Wall Models) KSACN0501AAA (Ducted/Cassette Models) INSTALLATION INSTRUCTIONS NOTE: Read the entire instruction manual before
More informationOwner s Manual RBC-AX32U(W)-E RBC-AX32U(WS)-E AIR CONDITIONER (SPLIT TYPE) Wireless remote controller kit. Model name: English.
AIR CDITIER (SPLIT TYPE) Owner s Manual Wireless remote controller kit Model name: RBC-AX3U(W)-E RBC-AX3U(WS)-E Generic model name RBC-AX3U(W)-E Wireless remote controller model name WH-LSE Signal receiving
More informationVR 80 Remote Control Device
For the owner and heating engineer Operating and installation manual VR 80 Remote Control Device Bus modular control system VR 80 GB Contents Contents Notes on the documentation...... 4 Other valid documents...
More informationD-Pack 6 Classic ORDERCODE 50315
D-Pack 6 Classic ORDERCODE 50315 Congratulations! You have bought a great, innovative product from Showtec. The Showtec D-Pack 6 Classic brings excitement to any venue. Whether you want simple plug-&-play
More informationSTR-3 STANDARD 3-PHASE 230 VAC TRANSFORMER CONTROLLER. Mounting and operating instructions
STANDARD 3-PHASE 230 VAC TRANSFORMER CONTROLLER Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA
More informationCOMFORT CONTROL CENTER SERVICE INSTRUCTIONS
USA SERVICE OFFICE Dometic Corporation 2320 Industrial Parkway Elkhart, IN 46516 574-294-2511 CANADA Dometic Corporation 46 Zatonski, Unit 3 Brantford, ON N3T 5L8 CANADA 519-720-9578 For Service Center
More informationMODELS DSH/DSV R-410A AIR SIDE ECONOMIZER KIT
MODELS DSH/DSV R-410A AIR SIDE ECONOMIZER KIT Form 145.11-IOM1 (412) AIR SIDE ECONOMIZER FOR DSH AND DSV R-410A AIR COOLED AIR CONDITIONING UNITS INSTALLATION INSTRUCTIONS B Style IMPORTANT! READ BEFORE
More informationMODELS DSH/DSV R-410A AIR SIDE ECONOMIZER KIT
MODELS DSH/DSV R-410A AIR SIDE ECONOMIZER KIT Form 145.11-IOM1 (412) AIR SIDE ECONOMIZER FOR DSH AND DSV R-410A AIR COOLED AIR CONDITIONING UNITS INSTALLATION INSTRUCTIONS B Style IMPORTANT! READ BEFORE
More informationMicroTech II TM Remote I/O Panel Installation Manual
Installation Manual IM 783-0 MicroTech II TM Remote I/O Panel Installation Manual Group: Controls Part Number: IM 783-0 Date: February 2004 Supersedes: New 2004 McQuay International Page 2 IM-783 Table
More informationSER8300 Series Line Voltage Room Controller with Optional PIR Sensor Installation Guide
Line Voltage Room Controller with Optional PIR Sensor Commercial and Hotel/Lodging HVAC Fan Coil Applications CONTENTS Installation 3 Location 3 Installation 3 Terminal, Identification and Function 4 Communication
More informationAir Quality Sensor KNX AQS
EN Air Quality Sensor KNX AQS Technical Specifications and Installation Instructions Elsner Elektronik GmbH Control and Automation Engineering Herdweg 7 D 75391 Gechingen Phone +49 (0) 70 56 / 93 97-0
More informationINSTALLATION INSTRUCTIONS ECONOMIZER WITH EXHAUST
INSTALLATION INSTRUCTIONS ECONOMIZER WITH EXHAUST MODEL WGSEIFM-5 For Use with Bard 3 through 5 Ton Step Capacity Wall Mount Air Conditioners with Gas Heat Bard Manufacturing Company, Inc. Bryan, Ohio
More informationMAKING MODERN LIVING POSSIBLE. Installation Guide. Twin Kit 086L
MAKING MODERN LIVING POSSIBLE Installation Guide 086L70 www.heating.danfoss.com Danfoss A/S is not liable or bound by warranty if these instructions are not adhered to during installation or service. The
More informationDESIGO RX Individual room controllers. for fan-coil systems, chilled ceilings and radiators, with LONMARK-compatible bus communications
3 834 DESIO RX Individual room controllers for fan-coil systems, chilled ceilings and radiators, with MARK-compatible bus communications RXC20.1 RXC21.1 The RXC20.1 and RXC21.1 controllers are used for
More informationComputer Temperature Interface model CTI-2. Description. Installation. Control Module
Description The Sine Systems model CTI-2 Computer-Temperature Interface allows a computer to monitor the outside air temperature. It consists of a 2.75 x 3 x 0.75 control module with 8 screw-terminal connections.
More informationFDS / FDS-R / FDS-PS
FDS / FDS-R / FDS-PS USER MANUAL For use with 120V 60Hz input. Output is 120V 60Hz at 5amps 600W MAX. switched. ETL LISTED Conforms to UL STD 1241 3091594 79-15167-00 REV. A www.fiberstars.com Page 1 of
More informationSE7600E Series. Installation Guide for Commerical HVAC Applications CONTENTS
SE7600E Series Installation Guide for ommerical HVA Applications ONTENTS Installation 2 Location 2 Installation 2 Terminal, Identification and Function 3 Screw terminal arrangement and wiring 3 Main outputs
More informationRoom unit with PPS2 interface
1 626 Room unit with PPS2 interface for use with: controllers with a PPS2 interface QAA88.3 Room temperature measurement Key buttons for adjustment of the room temperature setpoint Key buttons for operating
More informationSER8300 Series Line Voltage Room Controller with Optional PIR Sensor Installation Guide
Line Voltage Room Controller with Optional PIR Sensor Commercial and Hotel/Lodging HVAC Fan Coil Applications CONTENTS Installation 3 Location 3 Installation 3 Terminal, Identification and Function 4 Communication
More informationGavita Master Controller EL1
Gavita Master Controller EL1 User manual User manual Gavita Master controller EL1 Dear customer, Congratulations on the purchase of your Gavita Master controller EL1. This manual contains all the information
More informationGOLDENI. Owners Manual & Safety Instructions. English. model# GOLDi600. Copyright 2017 Smart Grow Technologies, INC All Rights Reserved
GOLDENI 600 model# GOLDi600 English Copyright 2017 Smart Grow Technologies, INC All Rights Reserved Owners Manual & Safety Instructions INTRODUCTION This User Manual is for Smart Grow Technologies (SGS):
More informationBACnet PTEC Unit Conditioner/Fan Coil P. Controller. Control Applications. Accessories. Product Description. Warning/Caution Notation
Installation Instructions BACnet PTEC Unit Conditioner/Fan Coil Controller Figure 1. BACnet PTEC Unit Conditioner/Fan Coil Controller. Control Applications 6540, 6541, 6550, 6551, 6552, 6553 and 6554 Product
More information1 Channel Strobe Controller ORDERCODE 40226
1 Channel Strobe Controller ORDERCODE 40226 Congratulations! You have bought a great, innovative product from Showtec. The Showtec Strobe Controller brings excitement to any venue. Whether you want simple
More informationMicroTech II Remote I/O Panel Installation Manual
MicroTech II Remote I/O Panel Installation Manual Installation Manual IM 783-2 Group: Controls Part Number: IM 783 Date: November 2006 Supersedes: IM 783-1 Table of Contents Notice... 3 Reference Documents...
More informationInstallation Instructions
Please read all instructions before installing RS-350 PIR Dual Relay Universal Application Wall Switch Vacancy Sensor with Manual ON/OFF Lens Lighted Switch ON/OFF button for Relay 1 ON/OFF button for
More informationSE7600F Series. Installation Guide for RTU with Modulating Heat CONTENTS
SE7600F Series Installation Guide for RTU with Modulating Heat ONTENTS Installation 2 Location 2 Installation 2 Model hart 3 Network ready 3 Terminal, Identification and Function 3 Screw terminal arrangement
More informationInstallation Manual RB-RWS20-E. Lite-Vision plus Remote Controller. Model name: English
Model name: RB-RWS20-E Read this manual before using the RB-RWS20-E remote controller. Refer to the supplied with the indoor unit for any installation instructions other than operations of the remote controller.
More informationBTU-4D/BTU-4D-I Digital Temperature Unit & Sensors. Installation and Operation Manual
BTU-4D/BTU-4D-I Digital Temperature Unit & Sensors Installation and Operation Manual BTU-4D/BTU-4D-I Installation and Operation Manual Rev E Table of Contents Introduction... 1 TEMP OUTDOOR Sensor... 1
More informationPILOT TONE DETECTION MODULE IMPEDANCE DETECTION MODULE
INSTALLATION MANUAL VX-2000 series PILOT TONE DETETION MODULE IMPEDANE DETETION MODULE VX-200SP-2 VX-200SZ-2 Thank you for purchasing TOA s VX-2000 series plug-in modules. Please carefully follow the instructions
More informationSapling Converter Box
Installation Manual Sapling Converter Box SCB-100-000-1 Version Number 1.2 Current as of March 15, 2015 The Sapling Company, Inc. (+1) 215.322.6063 P. (+1) 215.322.8498 F. 2-Wire Converter Box (SCB-100-000-1)
More informationVSD-1MC MANUAL 0-10V / 4-20mA Variable Speed Module with Manual Override
MANUAL 0-10V / 4-20mA Variable Speed Module with Manual Override Varifan 3 4 5 6 7 MANUAL 2 8 1 OFF 10 9 AUTO MANUAL SPEED Installation / User s Guide This guide will inform the electrician on proper wiring
More informationDownflow Economizers Z1ECON30 (98W09) ECONOMIZERS
Downflow s Z1EON30 (98W09) EONOMIZERS INSTALLATION INSTRUTIONS FOR EONOMIZERS USED WITH Z,ZG,ZH 036,048,060 UNITS Application The Z1EON30 (98W09) economizer is used with Z,ZG,ZH 036,048,060 units in downflow
More informationProduct and function description
GAMMA instabus The following display and operating functions can be configured: switching, switching with forced control, dimming, sun protection control, recall and save scenes, sending and displaying
More informationOperating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
More informationUser Manual. Item no.: Otto Graf GmbH Carl-Zeiss-Str. 2-6 Tel.: +49(0) Kunststofferzeugnisse D Teningen Fax: +49(0)
User Manual AquaControl + Rainwater System Controller Item no.: 351027 Otto Graf GmbH Carl-Zeiss-Str. 2-6 Tel.: +49(0)7641-5890 Kunststofferzeugnisse D-79 331 Teningen Fax: +49(0)7641-58950 Page 1 Figure
More informationT7560A1036 Digital Wall Module
T7560A1036 Digital Wall Module HONEYWELL EXCEL 5000 OPEN SYSTEM BEFORE INSTALLATION All wiring must comply with local electrical codes and ordinances or as specified on installation wiring diagrams. T7560A1036
More informationBTU 4 & Sensors. Installation and Operation Manual
BTU 4 & Sensors Installation and Operation Manual Table of Contents Introduction... 1 Sensors... 1 BTO Outdoor Sensor... 1 BTI Indoor Sensor... 2 BTS Stack Sensor... 2 Installation... 3 BTU 4 Burk Temperature
More informationOverview These instructions are presented as a guideline for installing and setting up the LX Series Breaker Control Panel.
LX Breaker Control Panels Installation and Setup Procedure Hubbell Building Automation, Inc. 9601 Dessau Road Building One Suite 100 Austin, Texas 78754 512-450-1100 512-450-1215 Fax www.hubbell-automation.com
More information1:1 Model Connection Interface
Air Conditioner Installation Manual 1:1 Model Connection Interface Model name: TCB-PCNT31TLUL Installation Manual Digital Inverter Air Conditioner 1 English Manuel d installation Climatiseur inverseur
More informationAntenna Distributor ORDERCODE D1444
Antenna Distributor ORDERCODE D1444 Congratulations! You have bought a great, innovative product from DAP Audio. The DAP Audio TAS series bring excitement to any venue. Whether you want simple plug-&-play
More informationQuickTouch (QT4) Owner s Manual
QuickTouch (QT4) Owner s Manual 4-Function Hand-Held Wireless Remote Control IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION I. APPLICATION...
More informationTemperature controller Ducted systems
2 725 Temperature controller Ducted systems Standard model without zoning functions RRV851 Multifunctional controller used for central control of ducted HVAC systems in combination with a QAX850 master
More informationConfigurable Output Distribution. 120V / 208V / 240V 60Hz. User Manual English
Configurable Output Distribution 120V / 208V / 240V 60Hz User Manual English TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS.......................... 1 GLOSSARY OF SYMBOLS....................................
More informationRoom Temperature Controllers
3 021 Room Temperature Controllers for two-pipe fan coil units RCC10 Output for on / off valve actuator Outputs for three-speed fan Control depending on the room or return air temperature (RCC10) Automatic
More informationProduct and Function Description
Product and Function Description and the LED display. The touchscreen can be used to select from up to 6 languages for the display of texts and messages. The room temperature controller integrated in Contouch
More informationVRp Three-Phase Precision AC Voltage Regulator
VRp-22500-0338 Three-Phase Precision AC Voltage Regulator INSTALLATION INSTRUCTIONS Inspection and Unpacking Please inspect the wooden crate for obvious shipping damage. Some crates contain up to six (6)
More informationInstallation and Operation Guide for PD5200 and PD5300 Automatic Transfer Switch
Installation and Operation Guide for PD5200 and PD5300 Automatic Transfer Switch PD52 PD52S & PD52DCS PD53-100 te: The PD52S & PD52DCS are provided with LED lights. The GREEN LIGHTS indicate Shore Power
More informationTEC Unit Conditioner Controller
Document No. 540-1026 TEC Unit Conditioner Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2040 and 2041 2050 through 2054 Product Description
More informationRE-82 RACK MOUNT DIMMER OWNERS MANUAL. 8 X 2400Watts. Revision /29/2007
RE-82 RACK MOUNT DIMMER 8 X 2400Watts OWNERS MANUAL Revision 2.4 11/29/2007 Page 2 of 8 RE-82 CONTROL PANEL DESCRIPTION The RE-82 is an 8 channel dimmer with a maximum capacity of 2,400 watts per channel
More informationICS Entrance Management Sign Installation Guide. Version 1.0
ICS Entrance Management Sign Installation Guide Version 1.0 Thank you for purchasing your new ICS Entrance Management System (EMS) from Innovative Control Systems, Inc. Installation Overview This document
More informationWINSTA. Full Line Catalog 2008/2009
WINSTA Full Line Catalog 2008/2009 5 Contents FULL LINE CATALOG W4, Volume 1 Rail-Mounted Terminal Block Systems FULL LINE CATALOG W4 Rail-Mounted Terminal Blocks Volume 1 X-COM -SYSTEM Terminal Strips
More informationContent. Product Description
EY-modulo 4 EY-RU482F001 Room Operating Unit with Display for Fan Coil applications EY-RU483F001 Room Operating Unit with Display for VAV applications en Guidelines for the electrician Content 1 Product
More informationEC Series. Safety Guide
EC Series Safety Guide R5906018/02 01/07/2017 Barco Inc, Image Processing 3078 Prospect Park Drive, Rancho Cordova, CA, 95670, USA Phone: +1 916 859-2500 Fax: +1 916 859-2515 Support: www.barco.com/en/support
More informationTechnical Note Series
Technical Note Series pir SENSOR (T2600) S TN0012-0 0 p I R S e n s o r Page 2 IMPORTANT OPERATION INFORMATION Type BF Equipment Internally powered equipment Continuous operation WARNING Explosion Hazard;
More informationBlu2Light Light Management Installation in Luminaires
BLUETOOTH WIRELESS TECHNOLOGY DEVICES FOR INSTALLATION IN LUMINAIRES BLUETOOTH WIRELESS TECHNOLOGY DEVICES FOR INSTALLATION IN LUMINAIRES Blu2Light The intelligent wireless lighting control solution Blu2Light
More informationCLS Atmosphere LED-panel
INDEX Index 2 Introduction Included items Optional accessories Safety information 4 Installation REVO Colour Flow 5 LDC connectioncable for the REVO Colour Flow 6 Assemble a REVO Colour Flow connectioncable
More informationOperation Manual. Concorde 600 Power Supply. *This instrument is intended for laboratory use only.
Concorde 600 Power Supply Operation Manual Cat.no. R10-1001011 *This instrument is intended for laboratory use only http://www.recenttec.com E-mail : support@recenttec.com Version 1.1 Packing List x 1
More informationInView Marquee Message Display
Installation Instructions InView Marquee Message Display Introduction These instructions show how to change the serial address and how to mount InView series signs with NEMA Types 4, 4X, and 12 enclosures.
More informationOmnitron Systems Technology, Inc. 1. iconverter. 19-Module Managed Power Chassis User s Manual
Omnitron Systems Technology, Inc. 1 iconverter 19-Module Managed Power Chassis User s Manual 27 Mauchly, #201, Irvine, CA 92618 Phone: (949) 250-6510; Fax: (949) 250-6514 2 Omnitron Systems Technology,
More informationRoom Temperature Controller
3 023 Room Temperature Controller for four-pipe fan coil units RCC30 Outputs for on / off valve actuators Outputs for three-speed fan Control depending on room or return air temperature Operating modes:
More informationINSTALLATION MANUAL For authorized service personnel only.
AIR CONDITIONER SIMPLE REMOTE CONTROLLER (WIRED TYPE) UTY-RSNUM INSTALLATION MANUAL For authorized service personnel only. English Français Español Contents. SAFETY PRECAUTIONS...2 2. ACCESSORIES...2 3.
More informationENGLISH Flexstrip Set RGB
MANUAL ENGLISH Flexstrip Set RGB V1 Highlite International B.V. Vestastraat 2 6468 EX Kerkrade the Netherlands Table of contents Warning... 2 Safety Instructions... 2 Operating Determinations... 4 Connection
More informationCharging Cabinet Owner s Manual
by edugear Charging Cabinet Owner s Manual Before using, please read these operating instructions carefully. They contain important advice concerning the use and safety of your Charging Cabinet. The Charging
More informationENGLISH Flexstrip Set IP44 RGB
MANUAL ENGLISH Flexstrip Set IP44 RGB V1 Highlite International B.V. Vestastraat 2 6468 EX Kerkrade the Netherlands Table of contents Warning... 2 Safety Instructions... 2 Operating Determinations... 4
More informationCOMPACT LED DESK LAMP WITH LCD DISPLAY
COMPACT LED DESK LAMP WITH LCD DISPLAY User manual, Operating- and safety instructions, Warranty conditions LED 12 MON Item no.: MROS501 Getting started and operation 1 180 1. Setting up Place the LED
More informationINSTALLATION MANUAL. Remote controller BRC315D7
INSTALLATION MANUAL 2 3 4 2 2 S M S M PCB J5 J8 2 3 5 4 5 6 6 7 P2 P P2 P a d 2 b c 4 3 UNIT No. GROUP SETTING e 3 7 4 5 6 7 6 5 2 READ THIS MANUAL ATTENTIVELY BEFORE STARTING UP THE UNIT. DO NOT THROW
More informationWise HP33 THREE PHASE HIGH PRECISION AVR SURVO-MOTOR AUTOMATIC VOLTAGE STABILIZER
Wise HP33 THREE PHASE HIGH PRECISION AVR SURVO-MOTOR AUTOMATIC VOLTAGE STABILIZER LEN.MAN.STA.111 Rev.4.00/2010 CONTENTS 1. SAFETY INSTRUCTIONS 1 2. INTRODUCTION 2 3. FRONT PANEL AND CONNECTION BOARD 3
More informationPRECAUTIONS FOR USE. Be sure to use indoor wiring within the specified voltage requirements. For extension cord, use the specified rating or more.
PRECAUTIONS FOR USE WARNING Be sure to consult an industry specialist when setting up, moving or transporting this product. This product should not be set up, moved or transported by any one other than
More information- ELV OVERVIEW. InstallationGuide SUPPLIED PARTS RELATED PARTS. Brackets Fixtures. Other. 1 of 9 IG-STR9-ELV
OVERVIEW The STR9 ELV is a long run, low power, linear surface mount LED lighting system designed for exterior architectural lighting applications. This guide contains important information on planning
More informationWhat s in the Box? REAR VIEW SAFETY
TM 1 What s in the Box? 1 Full HD Color Infra-red Weather Proof Camera 1 Full HD 7" TFT LCD Color Monitor w/monitor Mount 1 Power Harness 1 66 Camera Cable 1 Power Connection Wire 1 Screw Kit for installation
More informationREMOTE CONTROLLER (WIRED TYPE) INSTALLATION MANUAL. For authorized service personnel only. PART No
REMOTE CONTROLLER (WIRED TYPE) INSTALLATION MANUAL For authorized service personnel only. PART No. 938007-0 INSTALLATION MANUAL PART No. 938007-0 REMOTE CONTROLLER (WIRED TYPE) Contents. SAFETY PRES....
More informationUSER MANUAL. Uninterruptible Power Supply Line-interactive VCL Series UPS VA. GE Critical Power
Critical Power USER MANUAL Uninterruptible Power Supply Line-interactive VCL Series UPS 400 600 800 1000 1500 VA GE Consumer & Industrial SA General Electric Company CH 6595 Riazzino (Locarno) Switzerland
More informationDSTHM-2 COMBINED T AND RH DUCT TRANSMITTER. Mounting and operating instructions
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 4 OPERATIONAL DIAGRAMS 5 WIRING AND
More informationT775S Series 2000 Expansion Module
T775S Series 000 Expansion Module INSTALLATION INSTRUTIONS PRODUT DESRIPTION The T775S008 Relay Expansion Module is a four relay device for use with the T775L007 and T775P00 Series 000 Electronic Stand-Alone
More informationI/O Expansion Box Installation & Operator s Instruction Manual
I/O Expansion Box Installation & Operator s Instruction Manual May 2004 CTB Inc. Warranty I/O Expansion Box CTB Inc. Warranty CTB Inc. warrants each new Chore-Tronics product manufactured by it to be free
More informationTouch-controller_IM_03943A_1_Co_EN.indd 오후 3:06:00
Touch-controller_IM_03943A_1_Co_EN.indd 2 2013-06-28 오후 3:06:00 Touch Centralized Controller MCM-A300N Air Conditioner installation manual This manual is made with 100% recycled paper. imagine the possibilities
More informationPromopar ORDERCODE 30120
Promopar ORDERCODE 30120 Congratulations! You have bought a great, innovative product from Showtec. The Showtec Promopar brings excitement to any venue. You can rely on Showtec, for more excellent lighting
More informationLine reactors SINAMICS. SINAMICS G130 Line reactors. Safety information 1. General. Mechanical installation 3. Electrical installation
Safety information 1 General 2 SINAMICS SINAMICS G130 Mechanical installation 3 Electrical installation 4 Technical specifications 5 Operating Instructions Control version V4.7 04/2014 A5E00331462A Legal
More informationDTC P0AA6 - High Voltage Isolation Fault
DTC P0AA6 - High Voltage Isolation Fault Product Family Orion BMS [Original] (24-180 Cell) Orion BMS 2 (24-180 Cell) Orion JR (16 Cell) Fault Supported YES YES NO FAULT DESCRIPTION This code is set when
More informationETM-2050/ETM-2051 Service Manual
Introduction Novar s Electronic Thermostat Modules (ETMs) are intelligent control modules that provide local, direct digital control of unitary, packaged, staged HVAC systems. This document: Describes
More informationORB TM 4-20 ma Input Box Installation & Operation Manual
IOM ORB TM 4-20 ma Input Box Installation & Operation Manual ORB TM 4-20 ma Input Box Installation & Operation Manual CONTENTS I. HANDLING & STORAGE... 1 Inspection and Handling Disposal and Recycling
More informationZC-OH5 TAMPER-RESISTANT INDOOR/OUTDOOR HOUSING INSTRUCTION MANUAL FOR USE WITH GANZ ZC-D5000 SERIES MINIDOME CAMERAS
ZC-OH5 TAMPER-RESISTANT INDOOR/OUTDOOR HOUSING INSTRUCTION MANUAL FOR USE WITH GANZ ZC-D5000 SERIES MINIDOME CAMERAS Please carefully read and observe all instructions and warnings contained in this manual
More informationUTY-RVNUM. INSTALLATION MANUAL For authorized service personnel only. MANUEL D'INSTALLATION Pour le personnel agréé uniquement.
REMOTE CONTROLLER (WIRED TYPE) INSTALLATION MANUAL For authorized service personnel only. English UTY-RVNUM MANUEL D'INSTALLATION Pour le personnel agréé uniquement. Français MANUAL DE INSTALACIÓN Sólo
More informationPowerware 3105 UPS User s manual
Powerware 3105 UPS 2005 Eaton Corporation All Rights Reserved The contents of this manual are the copyright of the publisher and may not be reproduced (even extracts) unless permission granted. Every care
More informationPowerware 3105 UPS User s manual
Powerware 3105 UPS 2005 Eaton Corporation All Rights Reserved The contents of this manual are the copyright of the publisher and may not be reproduced (even extracts) unless permission granted. Every care
More informationSeries F75 Fail-Safe Module Installation, Operation and Maintenance Instructions
WCAIM2029 (Part 16022) Series F75 Fail-Safe Module Installation, Operation and Maintenance Instructions CAUTION: Flowserve recommends that all products that must be stored prior to installation be stored
More information1/2 Introduction. SIMBOX LC 1/7 Introduction 1/8 Flush-mounting and surfacemounting. 1/9 Dimensional drawings
Siemens AG 200 ALPHA SIMBOX Small Distribution Boards /2 Introduction /2 Introduction /3 Flush-mounting and hollow-wall distribution boards /4 Hood-type distribution boards /5 Accessories /6 Dimensional
More informationLEGA ENERGY ELECTRONIC RELAY VOLTAGE STABILIZER VA USER MANUAL
RELAY VOLTAGE STABILIZER 500 1000 2000 3500 5000 VA USER MANUAL 1- By-pass manuel switch 2- RJ-11 jacks 3- Power signal lamp 4- Stabiliser indication 5- Output plugs 6- Input plug LEGA ENERGY ELECTRONIC
More informationTyp: CAS # GEV_1_fam_RZ_luensee_print.indd :53
Typ: CAS # 088306 Abb./Fig. 1 Abb./Fig. 2a Abb./Fig. 2b Abb./Fig. 3 Abb./Fig. 4 2 ~230V~ -12V+ ~230V~ -12V+ Abb./Fig. 5 ~ ~ 230V PRI SEC 12V ~ ~ Abb./Fig. 6 ~ ~ 230V PRI SEC 12V ~ ~ 3 1-House Audio Door
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationInstallation Manual. 12 Volt Power Supplies. 18-Port. 9-Port RET18PT RET9PT
12 Volt Power Supplies Installation Manual 9-Port RET9PT 18-Port RET18PT INTRODUCTION Congratulations! The RET9PT 9-Port 12V Power Supply is the perfect solution for your larger security installations.
More informationLarge Police Light 100W ORDERCODE 80361
Large Police Light 100W ORDERCODE 80361 Congratulations! You have bought a great, innovative product from Showtec. The Showtec Large Police Light brings excitement to any venue. You can rely on Showtec,
More information