FLEXIBLE AND MODULAR PROCESSOR T11 MULTI I/O MODULES. The Heart of ADwin Pro-II. All-rounder with A/D, D/A, counters, SSI and EtherCAT

Transcription

1 ADWIN-PRO II - Modules FLEXIBLE AND MODULAR PROCESSOR T11 The Heart of ADwin Pro-II The processor module is the center of each ADwin-Pro II system. It executes the ADbasic instructions and accesses the inputs, outputs and interfaces of the other modules. The Pro-CPU-T11 processor module offers highest real-time computing power and is software-compatible to all previous versions. ADSP TS101 (300 MHz) 256 MB DRAM, 768 kb CPU-RAM Trigger input 2 Digital I/Os Ethernet interface 100 MBit/s for communication to the PC,effective data throughput 10 MB/s Bootloader option for stand-alone operation MULTI I/O MODULES All-rounder with A/D, D/A, counters, SSI and EtherCAT The multi I/O modules for ADwin-Pro II are the autonomous all-rounders for any type of signals: The module combines the fast reacting TiCo processor with analog and digital I/Os. On this basis, the intelligent slide-in card can react independently to measurement values and events and disburden the main processor, for example performing as fast closed-loop controller, digital filter for analog signals, function generator or intelligent limit monitor. There are even more possibilities using the extended version, e. g. : counter, SSI decoder or EtherCAT interface. General TiCo processor 128 kb internal memory 4 MB external SRAM 37-pole Sub-D plug Analog inputs 8 differential or 16 single-ended channels ADC resolution 18 bit; conversion time 2 µs Multiplexer settling time 2 µs Analog outputs 4 channels DAC resolution 16 bit Settling time 9 µs Digital channels 8 channels with TTL logic configurable as inputs or outputs in groups of 4 Extension MIO-4-ET1 (ordering option) 4 transistor outputs 4 optically isolated iinputs 1 counter block with two 32 bit counters: a forward/backward counter and a counter for PWM analysis 1 SSI decoder 1 EtherCAT interface (slave) Issue : July 11

2 ANALOG MODULES Interfaces for analog signals The analog modules for ADwin-Pro II systems are the best solution for time-critical tasks. The analog inputs have a resolution of up to 18 bit and offer sample rates up to 50 MHz. 256 MB of data memory is available for temporary data storage on modules with parallel analog inputs. The processor T11 accesses the measurement values of the ADC modules via the ADwin-Pro II bus with up to 200 MB/s. Analog input modules Multiplexed inputs 16 differential or 32 single-ended channels ADC's with a resolution of 18 bit; conversion time 2 µs Multiplexer settling time 2 µs optional with TiCo processor Parallel analog inputs one ADC per channel for synchronous sampling 4 or 8 differential channels resolution 14, 16 or 18 bit 14 bit: conversion time µs 16 bit: conversion time 0.25 µs 18 bit: conversion time 2.0 µs On-board memory 256 MB RAM Build-in edge detection for comparator purposes 16 bit module: optional mean value calculation from a defined number of measurement values Analog output modules The analog output modules allow synchronous data output on 4 or 8 channels without time offset. The DACs have a resolution of 16 bit and and offer a large band with. Pro II AOut-4/16, Pro II AOut-8/16 4 or 8 channels 16 bit resolution Settling time 3 µs Data output 10 times faster than on Pro I modules DIGTAL MODULES ADwin-Pro II and digital signal Digital input and output modules are the interfaces to your measurement devices and digital sensors. Select the digital modules suitable to your signal type. Digital input and output modules DIO-32, DIO-32-TiCo: 32 TTL inputs / outputs, build-in edge detection with time stamp for comparator purposes, optionally with TiCo processor and 256 MB memory OPT-16: 16 optocoupler inputs, min. switching time 100 ns, build-in edge detection with timestamp, input voltage range separately settable for each channel to 5 V, 12 V or 24 V REL-16: 16 relays outputs, switched voltage up to 30 V as normally open contact, response time4 ms, optionally available as normally closed contacts TRA-16: 16 transistor outputs, switched voltage 5 30 V, switching time 2,5 μs, optionally switching to ground PWM-16(-I): 16 PWM outputs, TTL compatible, optionally transistor outputs 5 30 V, separate signal configuration for each channel, reference clock 100 MHz, switching time20 ns (TTL) or < 3 μs (transistor) Customer-specific input and output modules

3 COUNTER MODULES Counter modules for fast digital signals The ADwin-Pro II counter modules can be used for connecting incremental encoders, for event counting, or for the analysis of pulse width modulated signals. Universal counter modules, individually configurable 32 -bit counter for the following modes pulse or event counter PWM analysis, pulse width measurement incremental encoder inputs clock / direction or A / B with 4-edge-evaluation 2 SSI inputs, 5 V differential (RS-422) additionally on differential version Module variants according to input signals: Pro II-Cnt-T: TTL signals Pro II-Cnt-D: 5 V differential (RS-422) Pro II-Cnt-I: optically isolated 5 V / 12 V / 24 V Freely programmable TiCo processor e. g. for pre-processing of complex timing signals. BUS SYSTEM MODULES Communication in all directions ADwin-Pro II modules work with various bus systems and serial interfaces. An ADwin-Pro II system can simultaneously send messages and data via RS232, communicate with devices via CAN bus, and control a test stand. The following interfaces are available: Pro II-RSx-2: 2 x RS-232 / RS-485 (software-selectable), with TiCo processor Pro II-RSx-4: 4 x RS-232 / RS-485, (software-selectable), with TiCo processor Pro II-CAN-2: 2 x 2 CAN bus, low speed or high speed (CAN 2.0 part A+B, ISO 11898),incoming CAN messages can rise a CPU event. Module includes a TiCo processor. Pro II-LIN-2: 2 x LIN Bus Pro II-LIN-4: 4 x LIN Bus Pro II-Profi-SL: 1 x Profibus with slave interface Pro II-Flex-2: 2 x FlexRay; each controller is provided with 2 channels Pro II-EtherCAT-SL: 1 x EtherCAT with slave interface Other field bus interfaces on request TEMPERATURE MODULES Active temperature measurement with ADwin-Pro II Module for Pt sensors The temperature module Pro II-RTD-8 transforms signals of platinum temperature sensors with ADCs and thus enables to query temperature or the attached voltage. All required settings can be done by software. The on-module sequence control executes all measurements which strongly disburdens the main processor of the Pro II system. In addition, the module can automatically filter a defined (disturbance) frequency from the digital signals. Properties: Suitable for temperature sensors Pt100, Pt500, Pt1000, Ni100 Measurement range according to sensor -200 C C Input filter 25 khz Measurement resolution 0,015 K - Measurement accuracy ±0,1 K Module for thermocouples The temperature module Pro II-TC-8-ISO transforms signals of standard thermocouples and enables to query temperature or the attached voltage (with or without cold junction compensation). All required settings can be done by software. The on-module sequence control executes all measurements which strongly disburdens the main processor of the Pro II system. Properties: Suitable for thermocouples of type B, E, J, K, N, R, S, T Measurement range according to the norm IEC Measurement resolution 0,1 K

4 ORDERING INFORMATIONS ADwin-Pro-ІІ ADwin-Pro-II-BM ADwin-Pro-II-DC ADwin-Pro-II-light ADwin-Pro-II-light-DC ADwin-Pro-II-mini ADwin-Pro-II Enclosures 19 enclosure (19 inch wide, 5 ¼ inch high), AC power supply, 115/230V, slots. Desktop unit, all modules mounted from the front-side. 19 enclosure (19 inch wide, 5 ¼ inch high), AC power supply, 115/230V, slots. Desktop unit, all modules mounted from the backside. 19 enclosure (19 inch wide, 5 ¼ inch high), DC-DC converter 10-35V, slots. Desktop unit, all modules mounted from the front-side. ½ 19 enclosure (9 inch wide, 5 ¼ inch high), AC power supply 115/230V, 7 slots. Desktop unit, all modules mounted from the front-side. ½ 19 enclosure (9 inch wide, 5 ¼ inch high), DC-DC converter 10-35V, 7 slots. Desktop unit, all modules mounted from the front-side. enclosure (25HP wide, 3U high), DC-DC-converter 10-35V, 4-5 slots. Desktop unit, all modules mounted from the frontside. Processor Modules and Options Pro-CPU-T11-ENET Pro-Boot 1 processor ADSP, 32-bit, 300MHz, 768KB int. RAM, 256MB ext. RAM, 1 Ethernet interface (10/100Mbit/s) for communication with the computer, 1 trigger input. Option for Ethernet interface for stand-alone operation without PC,10 MB non-volatile data memory. Fetch / Write support for S7 SPS. Only in combination with an Ethernet interface. Analog Input Modules, multiplexed Pro-II-AIn-8/18 Pro-II-AIn-8/18-L2 Pro-II-AIn-16/18-C Pro-II-AIn-32/18-D Pro-II-AIn-8/18-8B Pro-II-AIn-16/18-8B Pro II-Ain-32/18-D-TiCo 8 diff. analog inputs, 18-bit ADC, 2µs conversion time, MUX 2µs, block measurement, limit monitoring, 1pin LEMO 8 diff. analog inputs, 18-bit ADC, 2µs conversion time, MUX 2µs, block measurement, limit monitoring, 2pin LEMO 32 single ended or 16 diff. current inputs 0..20mA, 500W Shunt (0,05%, TK10), 18-bit ADC, 2µs conversion time, MUX 2µs, block measurement, limit monitoring, D-SUB 32 single ended or 16 diff. analog inputs, 18-bit ADC, 2µs conversion time, MUX 2µs, block measurement, limit monitoring, D-SUB, isolated by optocouples 8 analog voltage inputs +/- 10V, 8 analog voltage inputs for 8B signal conditioning modules, 18-bit ADC, 2µs conversion time, block measurement, limit monitoring, D-SUB, 15 HP 16 analog voltage inputs for 8B signal conditioning modules, 18-bit ADC, 2µs conversion time, block measurement, limit monitoring, D-SUB, 15 HP 32 single ended or 16 diff. analog inputs, 18-bit ADC, 2µs conversion time, MUX 2µs, block measurement, limit monitoring, D-SUB isolated by optocouples, (TiCo) Analog Input Modules, Parallel Acquisition Pro-II-AIn-F4/14 Pro-II-AIn-F4/14-L2 Pro-II-AIn-F4/14-D Pro-II-AIn-F4/14-B Pro-II-AIn-F8/14 Pro-II-AIn-F8/14-L2 Pro-II-AIn-F8/14-D Pro-II-AIn-F8/14-B 4 analog diff. inputs, 4x 14-bit ADC, 4x50MHz, 256MB RAM averaging, limit monitoring, 1pin LEMO 4 analog diff. inputs, 4x 14-bit ADC, 4x50MHz, 256MB RAM averaging, limit monitoring, 2pin LEMO 4 analog diff. inputs, 4x 14-bit ADC, 4x50MHz, 256MB RAM, averaging, limit monitoring, D-SUB 4 analog diff. inputs, 4x 14-bit ADC, 4x50MHz, 256MB RAM, averaging, limit monitoring, BNC 8 analog diff. inputs, 8x 14-bit ADC, 4x50MHz, 8x25MHz, 256MB RAM averaging, limit monitoring, 1pin LEMO, 10 HP 8 analog diff. inputs, 8x 14-bit ADC, 4x50MHz, 8x25MHz, 256MB RAM, averaging, limit monitoring, 2pin LEMO, 10 HP 8 analog diff. inputs, 8x 14-bit ADC, 4x50MHz, 8x25MHz, 256MB RAM, averaging, limit monitoring, D-SUB, 10 HP 8 analog diff. inputs, 8x 14-bit ADC, 4x50MHz, 8x25MHz, 256MB RAM, averaging, limit monitoring, BNC, 10 HP

5 Pro-II-AIn-F4/16 Pro-II-AIn-F4/16-L2 Pro-II-AIn-F4/16-D Pro-II-AIn-F4/16-B Pro-II-AIn-F8/16 Pro-II-AIn-F8/16-L2 Pro-II-AIn-F8/16-D Pro-II-AIn-F8/16-B Pro-II-AIn-F4/18 Pro-II-AIn-F-4/18-L2 Pro-II-AIn-F-4/18-D Pro-II-AIn-F-4/18-B Pro-II-AIn-F-8/18 Pro-II-AIn-F-8/18-L2 Pro-II-AIn-F-8/18-D Pro-II-AIn-F-8/18-B and min./max. monitoring, 1pin LEMO and min./max. monitoring, 2pin LEMO and min./max. monitoring, D-SUB and min./max. monitoring, BNC limit and min./max. monitoring, 1pin LEMO limit and min./max. monitoring, 2pin LEMO limit and min./max. monitoring, D-SUB limit and min./max. monitoring, BNC, 10 HP 4 analog isolated inputs, 4x 18-bit ADC, 2µs conversion time, limit monitoring, 1pin LEMO 4 analog isolated inputs, 4x 18-bit ADC, 2µs conversion time, limit monitoring, 2pin LEMO 4 analog isolated inputs, 4x 18-bit ADC, 2µs conversion time, limit monitoring, D-SUB 4 analog isolated inputs, 4x 18-bit ADC, 2µs conversion time, limit monitoring, BNC 8 analog isolated inputs, 8x 18-bit ADC, 2µs conversion time, limit monitoring, 1pin LEMO 8 analog isolated inputs, 8x 18-bit ADC, 2µs conversion time, limit monitoring, 2pin LEMO 8 analog isolated inputs, 8x 18-bit ADC, 2µs conversion time, limit monitoring, D-SUB 8 analog isolated inputs, 8x 18-bit ADC, 2µs conversion time, limit monitoring, BNC, 10 HP Analog Output Modules Pro-II-AOut-4/16 Pro-II-AOut-4/16-D Pro-II-AOut-4/16-B Pro-II-AOut-8/16 Pro-II-AOut-8/16-D Pro-II-AOut-8/16-B 4 analog outputs, 16-bit DAC, 3µs conversion time, LEMO 4 analog outputs, 16-bit DAC, 3µs conversion time, D-SUB 4 analog outputs, 16-bit DAC, 3µs conversion time, BNC 8 analog outputs, 16-bit DAC, 3µs conversion time, LEMO 8 analog outputs, 16-bit DAC, 3µs conversion time, D-SUB 8 analog outputs, 16-bit DAC, 3µs conversion time, BNC, 10 HP Multi I/O Modules Pro-II-MIO-4 Pro-II-MIO-4-ET1 16 s.e. or 8 diff. analog inputs, 18-bit ADC, 2µs conversion time, MUX 5µs, 4 analog outputs, 16-bit DAC, 9µs conversion time, 8 TTL-I/Os configurable in groups of 4, TiCo 128 KB int./4mb ext. RAM, D-SUB 16 s.e. or 8 diff. analog inputs, 18-bit ADC, 2µs conversion time, MUX 5µs, 4 analog outputs, 16-bit DAC, 9µs conversion time, 8 TTL-I/Os configurable in groups of 4, TiCo 128KB int. /4MB ext. SRAM, D-SUB, 4x transistor outputs, isolated by optocouplers, max. 200 ma per channel, 4x optically isolated inputs, input voltage 5V-12 V-24V, common GND, 1x 32-bit counter (RS422) up / down counter with clock / direction or 4-edge evaluation, impulse measurement and simultaneous period width measurement, 1x SSI decoder, 1x EtherCAT slave, 10 HP Signal Conditioning Modules Pro-II-RTD-8 Pro-II-RTD-8-D 8 inputs for Pt100, Pt500, Pt1000, LEMO connector to the sensor, 10 HP 8 inputs for Pt100, Pt500, Pt1000, D-SUB connector to the sensor

6 Digital Input / Output Modules Pro-II-Dio TTL I/Os configurable in groups of 8 Pro-II-Dio-32-TiCo Pro II-OPT-16 Pro II-TRA-16 Pro II-TRA-16-G Pro II-REL TTL I/Os configurable in groups of 8, TiCo with 256MB 16 digital inputs with optocouplers. Input voltage 5V, 12V or 24V 16 transistor outputs, isolated by optocouplers, max. 200 ma per channel 16 transistor outputs, isolated by optocouplers, max. 200 ma per channel, low side driver 16 relay outputs (500mA) Counters, PW and PWM Modules Pro II-CNT-D Pro II-CNT-T Pro II-PWM-16 4x 32-bit counters (RS422), up/down counter with clock/direction or quadrature evaluation, impulse measurement and simultaneous period width measurement, 2x SSI- 4x 32-bit counters (TTL), up/down counter with clock/direction or quadrature evaluation, 16 pulse-width modulated signals (TTL), 32-bit Counters, PW and PWM modules (isolated by optocouplers) Pro II-CNT-I Pro II-PWM-16-I 4x 32-bit counters, up/down counter with clock/direction or quadrature evaluation, impulse measurement and simultaneous period width measurement, isolated by Transistor outputs for 16 pulse-width modulated signals, 32-bit, isolated by optocouplers (5V, 12V, 24V) Serial and fieldbus modules Pro II-RSx-2 Pro II-RSx-4 Pro II-CAN-2 Pro II-CAN-2-LS Pro II-LIN-2 Pro-II-PROFI-SL Pro II-CANopen Pro II-ModBus-RTU Pro II-xxxbus Pro II-Flex-2 2x RS232/485 interface, software-selectable, 9pin D-SUB connector, TiCo 4x RS232/485 interface, software-selectable, 9pin D-SUB connector, TiCo, 10 HP 2x CAN bus, high-speed, 9pin D-SUB connector, TiCo 2x CAN bus, low-speed, 9pin D-SUB connector, TiCo 2x LIN bus, 9pin D-SUB connector, TiCo 1x Profibus DP Slave interface, 9pin D-SUB CANopen inteface Modbus interface other bus interfaces on demand FlexRay interface module 2 controllers with 2 channels each, 9pin D-SUB Specifications are subject to change. Please, verify the latest specifications at time of order. ADAS Route d Elne MONTESCOT - France Phone : + 33 (0) Fax : + 33 (0) telemetry-sales@nexeya.com -