HyperDisk SOLID STATE DISK

Transcription

1 SOLID STATE DISK NAND Flash-based 2.5 SATA Standard Type Product Data sheet Preliminary Mar 2008 Storage Tecnologies Ltd

2 INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO HYPERDISK PRODUCTS, AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IN HYPERDISK PRODUCTS OR TECHNOLOGY. ALL INFORMATION IN THIS DOCUMENT IS PROVIDED ON AS "AS IS" BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND. 1. For updates or additional information about products, contact your nearest agent. 2. products are not intended for use in life support, critical care, medical, safety equipment, or similar applications where Product failure could result in loss of life or personal or physical harm, or any military or defense application, or any governmental procurement to which special terms or provisions may apply. is a registered trandemark of storage technologies Ltd. For further information please contact: storage technologies Ltd 18/C,Wing A, Yuehai Building,Nanhai Road, Shenzhen,CHINA, Phone: Fax: URL: Copyright 2005, 2017 storage technologies Ltd.

3 TABLE OF CONTENTS 1. General Description 2 2. Physical Specifications Physical Dimensions 3 3. Product Specifications System Interface and Configuration System Performance System Power Consumption 4 System Reliability Environmental Specifications 5 4. Electrical Specification " Type " Pin Locations " Pin Assignments Jumper Settings Signal Descriptions DC Characteristics Absolute Maximum Ratings Recommended Operating Conditions 8 5. Ordering Information 9 6. Product Line-up

4 1. General Description The Flash-based SSD of Electronics is fully consist of semiconductor device and using NAND Flash Memory which has a high reliability and a high technology for a storage media. As the SSD doesn't have a moving parts such as platter(disk) and head media, it gives a good solution in a sub. note PC and Tablet PC for a storage device with a high performance and a power consumption and a small form factor. Also it gives rugged features in industrial PC with an extreme environment and an increased MTBF. For an easy adoption, the SSD has a same host interface with HDD. Density: 512M to 128GB are available Power consumption : Active : Typical 300mA Idle : Typical 100mA Standby : Typical 20mA Form Factor: 100.2±0.25mm * 69.85±0.25mm * 9.5±0.25mm Temperature: Operating : -10 ~ 85 Operating : -40 ~ 85 (wide temperature type) Shock: Operating : 2000G, duration 0.5ms, Half Sine Wave Vibration : 15G Peak, 10~2000Hz,(12Cycle/Axis)x3 Axis Host interface Compliant with Serial ATA International Organization: Serial ATA Revision 2.6 Serial ATA interface of 3.0Gbps. Serial ATA power save modes. Serial ATA hot-plug. Serial ATA Set Features for disabling device-initiated Serial ATA power management. USB2.0 interface Compliant with Universal Serial Bus Specification Revision 2.0 Compliant with USB Mass Storage Class specification version 1.0 MTBF 2,000,000 Hours Performance Host Interface : Max 3.0Gbps/s Sustained Data Read : Max 160MB/s Sustained Data Write : Max 80MB/s Maxium Weight: Max 130g - 2 -

5 2. Physical Specifications 2.1 Physical Dimensions - 3 -

6 3. Product Specifications 3.1 System Interface and Configuration Serial ATA interface of 3.0Gbps. Serial ATA power save modes. Serial ATA hot-plug. Serial ATA Set Features for disabling device-initiated Serial ATA power management. 3.2 System Performance Read / Write Performance(MB/s) Random Read Sector Max 120 Random Write Sector Max 35 Sequential Read Sector Max 160 Sequential Write Sector Max System Power Consumption Current Typical(mA) Active 300 Idle 100 Standby 100 System Reliability MTBF 2,000,000 Hours - 4 -

7 3.4 Environmental Specifications Features Operating Non-Operating Temperature Humidity Vibration Shock Standard -10 C ~ 85 C -55 C ~ 125 C Wide-Temperature -40 C ~ 85 C 0 C to 55 C / 90~98% RH, 10cycles 15G Peak, 10 ~ 2000Hz, (12cycle / Axis) x3 Axis 2000G, duration 0.5ms, Half Sine Wave 4. Electrical Specification " Type " Pin Locations The following diagram identifies the Pin Locations of the SSD 2.5 Drive

8 " Pin Assignments PIN NAME PIN NAME 1 GND 8 GND 2 VCC 9 NC 3 RX_P 10 NC 4 RX_M 11 NC 5 GND 12 GND 6 TX_M 13 GND 7 TX_P 14 GND 15 VCC 16 VCC 17 GND 18 GND 19 GND 20 NC 21 NC 22 NC NOTE: NC is Reserved, don t connect it to anywhere, just leave it 4.2 Jumper Settings SATA SSD have no Jumper Settings - 6 -

9 4.3 Signal Descriptions Signal Pin NO Type Description VCC 14,15,16 I POWER SUPPLY: +5V ± 10% GND 1, 4,7,11,12,13,17,18, 19 I GROUND: Device Ground. TX_P 6 I Transmit Data. Differential analog output TX_M 5 I/O Transmit Data. Differential analog output RX_P 2 I Receice Data. Differential analog input RX_M 3 I/O Receice Data. Differential analog input - 7 -

10 4.4 DC Characteristics Absolute Maximum Ratings Characteristics Symbol Rating Unit DC Supply Voltage VDD 5.0V -0.3 to 5.5 V Input/Output Voltage VIN/VOUT 5.5 V DC Input Current I IN +/- 100 ma Storage Temperature T STG -55 to Recommended Operating Conditions Characteristics Symbol Rating Unit DC Supply Voltage VDD 5.0V 4.5 to 5.5 V Input/Output Voltage V IN /V OUT 5 V Operating Temperature T OPR -10 to 85 or -40 to Electrical Characteristics - Normal I/O Vdd = 4.5 to 5.5(V), Ta = 25, Vext = 5V ± 0.25V Characteristics Symbol Test Condition Min Typ Max Unit Input High Current IIH VIN = VDD Normal Pull - Down Down ua Input Low Current IIL VIN = VSS Pull - Up Normal Up ua Input High Voltage VIH CMOS V Input Low Voltage VIL CMOS V Output High Voltage VOH 6mA Buffer, IOH = -6mA V Output Low Voltage VOL 6mA Buffer, IOL = 6mA V Tri-state Output Leakage Current IOZ VOUT = VDD or VSS ua NOTE: Schmitt Trigger test condition : VDD = 4.5 to 5.5(V), Ta = 25 Characteristic: These DC parameters guarantee the I/O cell characteristic at the static state only, not at the dynamic state

11 5. Ordering Information D M 2 5 X X X - X X X X - X ~2. DM: Flash Disk Module 3~4. Drives Type 2 5 = 2.5 inch Type 3 5 = 3.5 inch Type 5. Disk Type S = Standard Flash Drives W = Wide-Temperature Flash Drives T = Special Flash Drives 6. Interface P = IDE/PATA S = SATA 7. component generation A = 1st Generation B = 2st Generation C = 3st Generation D = 4st Generation 8~11. Disk Density -128M~512M = 128M Byte~512M Byte -001G~064G = 1G Byte ~ 64G Byte 12. Flash Type -S = SLC -M = MLC - 9 -

12 6. Product Line-up Part Number Density Type Remark DM25SSB - 512M-S 512MB 2.5 DM25SSB - 001G-S 1GB 2.5 DM25SSB - 002G-S 2GB 2.5 DM25SSB - 004G-S 4GB 2.5 DM25SSB - 006G-S 6GB 2.5 DM25SSB - 008G-S 8GB 2.5 DM25SSB - 010G-S 10GB 2.5 DM25SSB - 012G-S 12GB 2.5 DM25SSB - 014G-S 14GB 2.5 DM25SSB - 016G-S 16GB 2.5 DM25SSB 018G-S 18GB 2.5 DM25SSB 020G-S 20GB 2.5 DM25SSB 022G-S 22GB 2.5 DM25SSB 024G-S 24GB 2.5 DM25SSB - 026G-S 26GB 2.5 DM25SSB 028G-S 28GB 2.5 DM25SSB 030G-S 30GB 2.5 DM25SSB 032G-S 32GB 2.5 DM25SSB 034G-S 34GB 2.5 DM25SSB 036G-S 36GB 2.5 DM25SSB 038G-S 38GB 2.5 DM25SSB 040G-S 40GB 2.5 DM25SSB 042G-S 42GB 2.5 DM25SSB 044G-S 44GB 2.5 DM25SSB - 046G-S 46GB 2.5 DM25SSB 048G-S 48GB 2.5 DM25SSB 050G-S 50GB 2.5 DM25SSB 052G-S 52GB 2.5 DM25SSB 054G-S 54GB 2.5 DM25SSB - 056G-S 56GB 2.5 DM25SSB 058G-S 58GB 2.5 DM25SSB 060G-S 60GB 2.5 DM25SSB 062G-S 62GB 2.5 DM25SSB 064G-S 64GB 2.5 DM25SSB 064G-S 128GB

13 For further information please contact: storage tecnologies 18/C Wing A Yuehai Building Nanhai Road Shenzhen China Phone Fax URL