User manual RFID-USB-DESK Reader

Transcription

1 User manual RFID-USB-DESK Reader

2 Dear Customer! Thank you very much for choosing our product. Before its use, please read these instructions carefully. There are given here the most appropriate ways of dealing with this device, the basic principles of safety and maintenance. Please also keep the user manual so that you can read it during later use. Remember! The manufacturer is not liable for any damage caused by improper use of the device for its intended purpose or improper handling, as well as fault driver resulting from improper use.

3 Table of contents: 1 PURPOSE OF THE DEVICE WARRANTY AND LIABILITY OF THE MANUFACTURER SAFETY GUIDELINES POWER SUPPLY STORAGE, WORKING ENVIRONMENT AND TRANSPORTATION INSTALLATION AND USE OF THE MODULE UTILISATION OF THE MODULE CONSTRUCTION OF THE DEVICE GENERAL FEATURES CONFIGURATION CONFIGURATION EXAMPLES...9 NOTES...11 Before starting work with the controller, read The User manual and follow the instructions contained therein!

4 1 Purpose of the device The device RFID-USB-DESK Reader reads 5 bytes code from UNIQUE standard transponders. Depending on configuration, the device can act as a standard keyboard or a virtual serial port (Virtual Com Port). 2 Warranty and liability of the manufacturer The manufacturer provides a 2-year warranty on the module. The manufacturer also provides post-warranty service for 10 years from the date of the introducing the module on the market. The warranty covers all defects in material and workmanship The manufacturer undertakes to comply with the contract of guarantee, if the following conditions are met:: all repairs, alterations, extensions and device calibrations are performed by the manufacturer or authorized service, supply network installation meets applicable standards in this regard, the device is operated in accordance with the recommendations outlined in this manual the device is used as intended. ProThe manufacturer assumes no responsibility for consequences resulting from improper installation, improper use of the module, not following this manual and the repairs of the module by individuals without permission. This device doesn t contain serviceable parts. The repairs can be done only by manufacturers approved repair service.

5 3 Safety guidelines The module has been constructed using modern electronic components, according to the latest trends in the global electronics. 3.1 Power supply The module is adapted to power directly from the USB port. 3.2 Storage, working environment and transportation The module has to be used in closed environments free from fumes and corrosive atmosphere. Environmental conditions for storage: temperature + 5 C +45 C, relative humidity does not exceed 75%, atmospheric pressure hPa. The device is designed to operate under the following conditions: temperature +10 C +30 C, relative humidity 30% 75%, atmospheric pressure hPa. Recommended conditions for transportation: temperature -10 C +45 C, humidity 20 95%, atmospheric pressure hPa. 3.3 Installation and use of the module The module should be used following the guidelines shown in next part of the user manual. 3.4 Utilisation of the module When it becomes necessary to liquidate the device (e.g., after the time of use), please contact the manufacturer or its representative, who are obliged to respond appropriately, i.e., collecting the module from the user. You can also ask the companies involved in utilization and / or liquidation of electrical or computer equipment. Under no circumstances should you place the device along with other garbage

6 4 Construction of the device 4.1 General Features The reader is equipped with a USB port that supports class CDC (virtual com port) and HID (keyboard). The device is also equipped with three LED and beeper which can be assigned functions: ON continuously on OFF continuously off ON Read switching on for 0.5 second after the correct reading of the card code Technical data: Supply voltage: USB 5VDC (the device is powered from the USB port of a computer) Transponders: Standard supported transponders: UNIQUE Frequency: 125kHz Coding: Manchester Reading distance: approximately 10cm Communication: USB port (keyboard emulation or a virtual COM port) Dimensions:

7 5 Configuration Once installed, the setup program RFIDdesk Config and run it, connect the USB cable to the computer and the module. Figure 1. Window view When the reader is detected in the system (USB Status: Connected) user can proceed to its configuration. Operating mode: USB mode: USB Keyboard Emulator the reader in the system will appear as a standard USB keyboard. Approaching the card, enters tag code in apropriet format, in active window.

8 USB mode: Virtual Com Port the reader in the system will be visible as a virtual serial port. After approaching the card, the device sends tag code, in chosen format to apropriet COM port. Buzzer: Depending on the selected option, beeper placed on the device, after reading the card code can make a sound. LED1 indicates connected power (in its basic configuration) LED2 unused (in its basic configuration) LED3 informing about the correct reading of the card code (in its basic configuration) For each of the LEDs can be assigned to event: ON LED continuous light OFF LED is not lit ON Read LED lights up for 1 second after a correct reading of the card code. Prefix a series that precedes the card code Postfix a series that closes the card code Output Format the format in which it will display the card code: Binary send 5 bytes of code card HEX LowerCase Letter card code in hexadecimal format with lowercase letters HEX UpperCase Letter card code in hexadecimal format with large letters HEX UpperCase Letter Minus card code in hexadecimal format with large letters and cons separating bytes of code Some applications require data input in decimal format. In this case, selecting: Decimal 4 bytes transforms the four youngest bytes, for example: 2B3C4D5E to the value Decimal 3 bytes transforms the three younegest bytes, for example: 3C4D5E to the value Decimal 3,5 bytes turns three and a half youngest byte, for example: B3C4D5E to the value Decimal 5 bytes turns all tag code to 13-digit decimal format for example: 1A2B3C4D5E to the value Read Delay No delay reads tag every 0,5 seconds

9 Only new TAG reads tag only one time even when it is still close to the reader. Next reading occurs only when the transponder is removed and again applied. User Defined (x 0.1 s) - setting the desired reading delay. 5.1 Configuration Examples Keyboard emulation, sending "code card" prefix, card number and enter: After applying the card in the active window will be displayed string: kod karty: and inserted enter symbol

10 Serial port CDC mode Application of the card will send the code to a virtual serial port. User can control the beeper and LEDs. Sending a byte to the virtual serial port causes the appropriate response: Meaning of the bits of send byte: BIT Meaning LED3 LED2 LED1

11 Notes