TEP-0700-IMX6UL MODULAR HMI PRODUCT MANUAL (TEP-0700-IMX6UL)

Transcription

1 TEP-0700-IMX6UL MODULAR HMI PRODUCT MANUAL (TEP-0700-IMX6UL) VER August 16, 2018

2 REVISION HISTORY Revision Date Originator Notes 1.00 August 16, 2018 TechNexion First public release Page 2 of 26

3 TABLE OF CONTENTS 1. Introduction General Care and Maintenance TEP-0700-IMX6UL Product Overview Functional Block Diagram Dimensions Device Cut-out Dimensions For Mounting Though a Panel External Connectors Internal Board Connectors External Connectors Serial Port Connectors (RS-XXX1/RS-XXX2) CAN Bus Connector (CANBus) Digital I/O Connectors (GPIO1/GPIO2/GPIO3) MicroSD Connector USB OTG (Type-C) Connector LED Light Indicator S1 Button RST Button USB Host Connector Fast Ethernet Interface Power Input Connector Grounding Internal Connectors and Expansion Options SW2 Panel Scanning Direction Switch SW3 Panel Backlight Switch RTC Battery Connector Mounting VESA Mounting Surface Mounting and O-ring Installation Ordering Information Custom Part Number Rule Standard Package Contents Important Notice DISCLAIMER Page 3 of 26

4 1. Introduction 1.1. General Care and Maintenance Your device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will help you. Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, allow it to dry completely. Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged. Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics. Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards. Do not open the device while power is on. Otherwise electrical shock may result. Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device. Do not paint the device. Paint can clog the moving parts and prevent proper operation. Unauthorized modifications or attachments could damage the device and may violate regulations governing radio devices. These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service facility for service. Regulatory information Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. We hereby declare that the product is in compliance with the essential requirements and other relevant provisions of European Directive 1999/5/EC (radio equipment and telecommunications terminal equipment Directive). Page 4 of 26

5 2. TEP-0700-IMX6UL Product Overview 2.1. Functional Block Diagram Page 5 of 26

6 2.2. Dimensions The following figure shows the TEP-0700-IMX6UL dimensions (unit: mm): Page 6 of 26

7 2.3. Device Cut-out Dimensions For Mounting Though a Panel The TEP-0700-IMX6UL can be mounted on the front or the back of the panel. In order to mount it from the front, a nominal rectangular cutout must be made in the panel. The following drawing shows the dimensions of the cut-out area (unit: mm): Page 7 of 26

8 2.4. External Connectors The TEP-0700-IMX6UL has a number of external connectors. Rear view: External Connectors: No. Description No. Description 1 RS-XXX1 (Serial Port) connector 9 LED Light indicator 2 RS-XXX2 (Serial Port) connector 10 S1 Boot Select button 3 CAN Bus connector 11 Reset button 4 GPIO1 connector 12 USB Host connector 5 GPIO2 connector 13 LAN2 RJ45 connector 6 GPIO3 connector 14 LAN1 RJ45 and PoE (optional) connector 7 MicroSD cardslot 15 Power Input connector 8 USB OTG (Type-C) connector 16 Grounding screw Page 8 of 26

9 Bottom view: Right side view: External Connectors: No. Description No. Description 1 RS-XXX1 (Serial Port) connector 9 LED Light indicator 2 RS-XXX2 (Serial Port) connector 10 S1 Boot Select button 3 CAN Bus connector 11 Reset button 4 GPIO1 connector 12 USB Host connector 5 GPIO2 connector 13 LAN2 RJ45 connector 6 GPIO3 connector 14 LAN1 RJ45 and PoE (optional) connector 7 MicroSD cardslot 15 Power Input connector 8 USB OTG (Type-C) connector 16 Grounding screw Page 9 of 26

10 Left side view without side cover: External Connectors: No. Description No. Description 1 RS-XXX1 (Serial Port) connector 9 LED Light indicator 2 RS-XXX2 (Serial Port) connector 10 S1 Boot Select button 3 CAN Bus connector 11 Reset button 4 GPIO1 connector 12 USB Host connector 5 GPIO2 connector 13 LAN2 RJ45 connector 6 GPIO3 connector 14 LAN1 RJ45 and PoE (optional) connector 7 MicroSD cardslot 15 Power Input connector 8 USB OTG (Type-C) connector 16 Grounding screw Page 10 of 26

11 2.5. Internal Board Connectors The TEP-0700-IMX6UL has several connectors, switches and internal expansion options. It is necessary to remove the Power Expansion module to access several switches, headers and connectors. Rear view (opened device) with the Power Expansion module: A B Power Expansion Module Internal Connectors and Switches: No. Description No. Description A SW2 Panel switch B RTC Battery connector Page 11 of 26

12 Rear view (opened device) without the Power Expansion module: A B D* C* Internal Connectors and Switches: No. Description No. Description A SW2 Panel switch C* SW3 Panel switch B RTC Battery connector D* Power Expansion module connector NOTE: Items marked with * are accessible only after removing the Power Expansion module. Page 12 of 26

13 3. External Connectors 3.1. Serial Port Connectors (RS-XXX1/RS-XXX2) The TEP-0700-IMX6UL has four non-galvanic isolated 2-wire RS-232 serial ports. RS-XXX1: Pin Signal Description Device # 1 GND Ground 2 SERIAL1A_TXD Port#1A Transmit data (output) ttymxc0 3 SERIAL1A_RXD Port#1A Receive data (input) ttymxc0 4 NC 5 NC 6 GND Ground 7 SERIAL1B_TXD Port#1B Transmit data (output) ttymxc1 8 SERIAL1B_RXD Port#1B Receive data (input) ttymxc1 9 NC 10 NC RS-XXX2: Pin Signal Description Device # 1 GND Ground 2 SERIAL2A_TXD Port#2A Transmit data (output) ttymxc2 3 SERIAL2A_RXD Port#2A Receive data (input) ttymxc2 4 NC 5 NC 6 GND Ground 7 SERIAL2B_TXD Port#2B Transmit data (output) ttymxc3 8 SERIAL2B_RXD Port#2B Receive data (input) ttymxc3 9 NC 10 NC Header on TEP-0700-IMX6UL: Molex (10-pin Micro-Fit 3.0). Cable receptacle: Molex (10-pin Micro-Fit 3.0) plug with crimp contact Molex Page 13 of 26

14 3.2. CAN Bus Connector (CANBus) The TEP-0700-IMX6UL has two non-galvanic isolated CAN Bus interfaces. CANBus: Pin # Signal Description Interface 1 GND_CAN Ground for CAN 2 CAN1A_TERM_P To enable CAN1A Termination, bridge with CAN1A_P can0 3 CAN1A_P CAN Bus 1A high (-24~+24V) can0 4 CAN1A_N CAN Bus 1A low (-24~+24V) can0 5 CAN1A_TERM_N To enable CAN1A Termination, bridge with CAN1A_N can0 6 NC 7 GND_CAN Ground for CAN 8 CAN1B_TERM_P To enable CAN1B Termination, bridge with CAN1B_P can1 9 CAN1B_P CAN Bus 1B high (-24~+24V) can1 10 CAN1B_N CAN Bus 1B low (-24~+24V) can1 11 CAN1B_TERM_N To enable CAN1B Termination, bridge with CAN1B_N can1 12 NC Header on TEP-0700-IMX6UL: Molex (12-pin Micro-Fit 3.0). Cable receptacle: Molex (12-pin Micro-Fit 3.0) plug with crimp contact Molex Digital I/O Connectors (GPIO1/GPIO2/GPIO3) The TEP-0700-IMX6UL has three non-galvanic isolated GPIO Expansion headers with the following pinout: GPIO1: Pin Signal Description Voltage Current GPIO GPIO # Min. Typ. Max. Max. Kernel Bank/IO 1 GPIO1A DIG_IN1/OUT1-0.5V 3.3V 6V 0.15mA 12 1_12 2 GPIO1B DIG_IN2/OUT2-0.5V 3.3V 6V 0.15mA 13 1_13 3 GND_DIO Ground for digital I/O 4 NC 5 GPIO1C DIG_IN5/OUT5-0.5V 3.3V 6V 50mA 500 pca GPIO1D DIG_IN5/OUT6-0.5V 3.3V 6V 50mA 501 pca VCC_DIO Supply output for d. I/O 3.3V 8 NC Page 14 of 26

15 GPIO2: Pin Signal Description Voltage Current GPIO GPIO # Min. Typ. Max. Max. Kernel Bank/IO 1 GPIO2A DIG_IN1/OUT1-0.5V 3.3V 6V 50mA 511 pca GPIO2B DIG_IN2/OUT2-0.5V 3.3V 6V 50mA 508 pca GND_DIO Ground for digital I/O 4 NC 5 GPIO2C DIG_IN5/OUT5-0.5V 3.3V 6V 50mA 509 pca GPIO2D DIG_IN5/OUT6-0.5V 3.3V 6V 50mA 510 pca VCC_DIO Supply output for d. I/O 3.3V 8 NC GPIO3: Pin Signal Description Voltage Current PWM GPIO* GPIO # Min. Typ. Max. Max. (default) Kernel Bank/IO 1 GPIO3A ADCI_INO -0.5V 3.3V 8 1_8 2 GPIO3B PWM_OUT or DIG_IN2/OUT2 3 GND_DIO Ground for digital I/O 4 NC -0.5V 3.3V 3.6V 0.15mA 4 5 1_5 5 GPIO3C PWM_OUT or -0.5V 3.3V 3.6V 0.15mA 3 4 1_4 DIG_IN5/OUT5 6 GPIO3D PWM_OUT or -0.5V 3.3V 3.6V 0.15mA 1 9 1_9 DIG_IN6/OUT6 7 VCC_DIO Supply output 3.3V 8 NC NOTE: GPIO3 port is set by default as PWM. GPIO setting requires software modification. Please connect with TechNexion support team for more details. Header on TEP-0700-IMX6UL: Molex (8-pin Micro-Fit 3.0). Cable receptacle: Molex (8-pin Micro-Fit 3.0) plug with crimp contact Molex Page 15 of 26

16 3.4. MicroSD Connector The TEP-0700-IMX6UL features a standard microsd cardslot which is connected to the NXP i.mx6ul integrated Ultra Secured Digital Host Controller (usdhc). The following main features are supported by usdhc: Compatible with the MMC System Specification version 4.2/4.3/4.4/4.41/5.0. Conforms to the SD Host Controller Standard Specification version 3.0. Compatible with the SD Memory Card Specification version 3.0 and supports the Extended Capacity SD Memory Card. Compatible with the SDIO Card Specification version 3.0. Supports 1-bit / 4-bit SD and SDIO modes The MMC/SD/SDIO host controller can support a single MMC / SD / SDIO card or device USB OTG (Type-C) Connector The TEP-0700-IMX6UL has one USB OTG (Type-C) connector (USB 2.0 signals only) that can be used to connect a host computer to the unit for programming and update purposes. Pin Signal Description Pin Signal Description # # A1 GND Ground B1 GND Ground A2 NC B2 NC A3 NC B3 NC A4 VBUS 5V Universal Serial Bus Power B4 VBUSD 5V Universal Serial Bus Power A5 CC1 OTG detection signal B5 CC2D OTG detection signal A6 USB_D+ USB differential pair signal B6 USB_D+ USB differential pair signal A7 USB_D- port 1 B7 USB_D- port 2 A8 NC B8 NC A9 VBUS 5V Universal Serial Bus Power B9 VBUSD 5V Universal Serial Bus Power A10 NC B10 NC A11 NC B11 NC A12 GND Ground B12 GND Ground 3.6. LED Light Indicator The TEP-0700-IMX6UL has one programmable LED Light indicator. LED # Color GPIO No. GPIO Bank/IO 1 Green 505 pca Page 16 of 26

17 3.7. S1 Button The TEP-0700-IMX6UL by default boots the unit from internal flash storage (emmc). By pressing the S1 button before applying power to the unit and keeping the button pressed for 10 seconds, the unit will boot from an alternative boot media (microsd card) RST Button The TEP-0700-IMX6UL features a RST button for system reset USB Host Connector The TEP-0700-IMX6UL has a standard single USB Host connector (USB 2.0 signals only) to connect to a USB peripheral such as a keyboard, mouse, USB storage device or USB hub. Page 17 of 26

18 3.10. Fast Ethernet Interface The TEP-0700-IMX6UL by default comes with two Fast Ethernet RJ45 connectors. LAN1 connector can support 802.3at Power over Ethernet functionality if configured with the PoE power option (TEP0700- IMX6G-05-Rxx-Exx-LPOE-xxxx) by connecting it to an 802.3at compliant PoE switch or power injector. LAN1 / LAN2: Pin # 100 Mbps 10 Mbps 1 Transmit Data+ Transmit Data+ 2 Transmit Data- Transmit Data- 3 Receive Data+ Receive Data Receive Data- Receive Data Power Input Connector The TEP-0700-IMX6UL can be powered either over the DC INPUT connector or PoE over the RJ45 LAN1 port (optional). NOTE: Do not power the unit by DC input when you apply power over the Power over Ethernet (RJ45)! Pin # Signal Description 1 GND Ground 2 VCC DC Voltage input (12V/24V/8~36VDC) Header on TEP-0700-IMX6UL: Molex (2-pin Micro-Fit 3.0). Cable receptacle: Molex (2-pin Micro-Fit 3.0) plug with crimp contact Molex Grounding The TEP-0700-IMX6UL must always be grounded to the earth. Grounding helps to limit the effects of noise due to electromagnetic interference on the device. The earth connection will have to be done using the grounding screw. The screw for the ground connection is marked with an engraved ground symbol. Page 18 of 26

19 4. Internal Connectors and Expansion Options Rear view (opened device) without the Power Expansion module: A B D* C* Internal Connectors and Switches: No. Description No. Description A SW2 Panel switch C* SW3 Panel switch B RTC Battery connector D* Power Expansion module connector NOTE: Items marked with * are accessible only after removing the Power Expansion module SW2 Panel Scanning Direction Switch The TEP-0700-IMX6UL has an internal SW2 Panel Scanning Direction switch (Marked A). Always use the default settings. Pin # 5 Panel 7 Panel (default) Description 1-8 ON OFF Down to Up 2-7 OFF OFF Up do Down 3-6 OFF OFF Left to Right 4-5 OFF OFF Right to Left Page 19 of 26

20 4.2. SW3 Panel Backlight Switch The TEP-0700-IMX6UL has an internal SW3 Panel Backlight switch (Marked D). Always use the default settings. Pin # 5 Panel 7 Panel (default) 1-2 OFF ON 4.3. RTC Battery Connector The TEP-0700-IMX6UL has an internal RTC backup battery connector (Marked B). Pin # Signal Description 1 GND Ground 2 RTC_VCC 3V (connect to standard CR2032 battery) Page 20 of 26

21 5. Mounting This section describes the mounting procedures for TEP-0700-IMX6UL. The material in area of the mounting must provide sufficient strength for safe mounting of this device VESA Mounting The TEP-0500-IMX6UL is compatible with the VESA MIS-C Standard 35*75mm hole pattern. There are 4 VESA MIS-C (M4) mounting holes on the rear side of the device. M4 screw holes are a depth of 4mm Page 21 of 26

22 5.2. Surface Mounting and O-ring Installation There are 8 mounting holes (M4) on the rear side of the device required for surface mounting. M4 screws with at least 5mm head-to-tip length are required to secure this device Please follow the steps below to properly install the waterproof rubber O-ring. Prepare your device and O- ring (Step 1-2). First, align the O-ring with the groove and press the O-ring into the corners of the O-ring groove (Step 3-4). Then, press it into the center (Step 5). Finally, stretch it uniformly around the O-ring groove (Step 6). Do not pull from one side, and make sure that you stretch it as little as possible. Page 22 of 26

23 6. Ordering Information The TEP-0700-IMX6UL is available in several configurations. Please contact your TechNexion sales contact window or distributor for options and availability details Custom Part Number Rule The TEP-0700-IMX6UL can be ordered in custom tailored configuration to meet special application requirements and conditions according to the following custom part number creation rules. Custom part numbers carry minimum order quantities (MOQ). Please connect with your TechNexion distributor or account manager for conditions and availability. Part number format: TEP0700-IMX6G-05-Rxx-Exx-Lxxx-xxxx Interface Code Description Processor IMX6G NXP i.mx6ultralite Processor Speed MHz Memory R02 256MB DDR3L R05 512MB DDR3L R10 1GB DDR3L Storage E04 emmc 4GB E08 emmc 8GB EXX emmc other capacity Power Expansion L112 TXR-P1-12V-LAN1 (12V 3A) L124 TXR-P1-24V-LAN1 (24V 3A) L130 TXR-P1-1030V-LAN1 (8-36V 5A) LPOE TXR-P1-12V-POE1 (12V 3A) or (PoE 802.3at) Custom ID XXXX Custom Part number ID for customized software loader and special component (BOM) Page 23 of 26

24 6.2. Standard Package Contents Item Partnumber Description 1 TEP-0700-IMX6UL 7 inch PoE HMI PCAP touch system with NXP i.mx6ul 2 2x rubber cable grommets 1x rubber O-ring 1x DC power latch cable (2-pin Micro-Fit 3.0) NOTE: Pack contents might vary depending on your ordered configuration. Page 24 of 26

25 7. Important Notice TechNexion reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TechNexion terms and conditions of sale supplied at the time of order acknowledgment. TechNexion warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TechNexion standard warranty. Testing and other quality control techniques are used to the extent TechNexion deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TechNexion assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TechNexion components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TechNexion does not warrant or represent that any license, either express or implied, is granted under any TechNexion patent right, copyright, mask work right, or other TechNexion intellectual property right relating to any combination, machine, or process in which TechNexion products or services are used. Information published by TechNexion regarding third-party products or services does not constitute a license from TechNexion to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TechNexion under the patents or other intellectual property of TechNexion. TechNexion products are not authorized for use in safety-critical applications (such as life support) where a failure of the TechNexion product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TechNexion products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TechNexion. Further, Buyers must fully indemnify TechNexion and its representatives against any damages arising out of the use of TechNexion products in such safety-critical applications. TechNexion products are neither designed nor intended for use in military/aerospace applications or environments unless the TechNexion products are specifically designated by TechNexion as military grade or "enhanced plastic." Only products designated by TechNexion as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TechNexion products which TechNexion has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TechNexion products are neither designed nor intended for use in automotive applications or environments unless the specific TechNexion products are designated by TechNexion as compliant with ISO/TS requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TechNexion will not be responsible for any failure to meet such requirements. Page 25 of 26

26 8. DISCLAIMER TechNexion Ltd. All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means whether, electronic, mechanical, or otherwise without the prior written permission of TechNexion Ltd. No warranty of accuracy is given concerning the contents of the information contained in this publication. To the extent permitted by law no liability (including liability to any person by reason of negligence) will be accepted by TechNexion Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document. TechNexion Ltd. reserves the right to change details in this publication without notice. Product and company names herein may be the trademarks of their respective owners. TechNexion Ltd. 16F-5, No. 736, Zhongzheng Road, ZhongHe District, 23511, New Taipei City, Taiwan Phone : Fax : sales@technexion.com Web : Page 26 of 26