Series 8000 RF Signal Switch Solution

Transcription

1 RF Signal Switch Solution Operation Manual Operation Manual, Part Number , Rev. A, May 17, 2013

2 All technical data and specifications in this publication are subject to change without prior notice and do not represent a commitment on the part of Giga-tronics, Incorporated Giga-tronics Incorporated. All rights reserved. Printed in the U.S.A. Warranty Giga-tronics Series 8000 instruments are warranted against defective materials and workmanship for one year from date of shipment, or as detailed in the warranty section of this manual. Giga-tronics will, at its option, repair or replace products that are proven defective during the warranty period. This warranty DOES NOT cover damage resulting from improper use, nor workmanship other than Giga-tronics service. There is no implied warranty of fitness for a particular purpose, nor is Giga-tronics liable for any consequential damages. Specification and price change privileges are reserved by Giga-tronics. MODEL NUMBERS The Series 8000 includes many models. Apart from the number of switches they support, the models are identical. The models are referred to in this manual by the general term Series 8000, except where it is necessary to make a distinction. CONTACT INFORMATION Giga-tronics, Incorporated 4650 Norris Canyon Road San Ramon, California Telephone: (only within the United States) (international) Fax: inquiries@gigatronics.com Website: Operation Manual, Part Number , Rev. A, May 16, 2013 Page 2

3 Regulatory compliance information This product complies with the essential requirements of the following applicable European Directives, and carries the CE mark accordingly. 89/336/EEC and 73/23/EEC EN (1993) EN (1997) EMC Directive and Low Voltage Directive Electrical Safety EMC Emissions and Immunity Manufacturer s Name: Giga-tronics, Incorporated Manufacturer s Address 4650 Norris Canyon Road San Ramon, California U.S.A. Type of Equipment: DC to 40 GHz RF Switch 8000 Model Series Number Model Numbers: 8000 Declaration of Conformity on file. Contact Giga-tronics at the following; Giga-tronics, Incorporated 4650 Norris Canyon Road San Ramon, California Telephone: (only within the United States) Fax: Operation Manual, Part Number , Rev. A, May 16, 2013 Page 3

4 Record of Changes to This Manual Use the table below to maintain a permanent record of changes to this document. Corrected replacement pages are issued as Technical Publication Change Instructions (TCPI). When you are issued a TCPI, do the following: 1. Insert the TCPI at the front of the manual binder. 2. Remove the pages from the manual binder that are noted in the TCPI. 3. Replace the page(s) removed in the previous step with the corrected page(s). 4. Record the changes in the table below. TPCI Number TPCI Issue Date Date Entered Comments Operation Manual, Part Number , Rev. A, May 16, 2013 Page 4

5 Record of Changes Revision Description of Change Chg Order # Approved By A Initial Release 3565 G.G. Operation Manual, Part Number , Rev. A, May 16, 2013 Page 5

6 Table of Contents SECTION SAFETY AND MANUAL CONVENTIONS... 7 OVERVIEW... 8 FUNCTIONAL DESCRIPTION... 8 WARRANTY... 8 FRONT/REAR VIEW... 9 SECTION UNIT DEFAULTS CONTROL COMMANDS SWITCH CLOSURE, COUNTER, QUERY COMMANDS SECTION AC INPUT MODULE FUSE FUSE, 250V, TYPE T, SLO-BLO, 6.3 AMP POWER SUPPLY SPECIFICATIONS Universal Power Supply, 250W, 5V/30A & 12V/16.7A, W/FAN SECTION RF SWITCH SPECIFICATIONS See your manual addendum for switch specifications SECTION OUTLINE DRAWINGS Series 8000 OUTLINE DRAWING RF SWITCH FACE DETAIL Operation Manual, Part Number , Rev. A, May 16, 2013 Page 6

7 LAN SAFETY AND MANUAL CONVENTIONS SECTION 1 This manual contains conventions regarding safety and equipment usage as described below. Product Reference Throughout this manual, the term Series 8000 refers to all models of within the series, unless otherwise specified. Personal Safety Alert! WARNING WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Equipment Safety Alert CAUTION CAUTION: Indicates a situation which can damage or adversely affect the product or associated equipment. Notes Notes are denoted and used as follows: NOTE: Highlights or amplifies an essential operating or maintenance procedure, practice, condition or statement. Electrical Safety Precautions Any servicing instructions are for use by service-trained personnel only. To avoid personal injury, do not perform any service unless you are qualified to do so. For continued protections against fire hazard, replace the AC line fuse only with a fuse of the same current rating and type. Do not use repaired fuses or short circuited fuse holders. Operation Manual, Part Number , Rev. B, Nov. 15, 2010 Page 7

8 OVERVIEW This manual describes a version of the Series 8000 products. They are full-rack wide units with terminated RF Switches that are controlled by an Ethernet or GPIB Interface. The Series 8000 line of switch products are based on rugged electromechanical switches and microwave relays rated for use from DC to 40 GHz, with low insertion loss and high isolation. Route signals under remote control to simplify and improve automated test systems. Easily removable switches allow reduced mean time to repair. The Series 8000 is a self-contained design, with built-in power supplies, microprocessor-based controller board and up to 256 relay coils, making it easy to implement a microwave switch system. It is designed to host many combinations of microwave relay switches, terminated or non-terminated: SPDT, SP4T, SP6T, SP8T, or Transfer switches. With a standard SCPI command set, the control interface provides the Series 8000 with ease of operation and configurability. FUNCTIONAL DESCRIPTION The design is housed in a 3 RU (5.25 inch) high, full rack size unit. The unit fits in a standard 19 inch rack cabinet and is provided with mounting flanges to enable it to be mounted in the rack. The unit is self contained, that is, it contains its own power supplies, communications interface, RF relay driver circuits and the RF relays mounted on the front. The RF Switches can be removed from the front of the unit. The Ethernet interface is an IEEE device and uses standard Control commands to control its digital interface. (See Section 2 for the Control Command Set for this instrument.) A single power supply provides +5 VDC and +12 VDC to the unit. The power supply input is VAC, Hz. (See Section 3 for full specifications) The RF switches are 50 Ohm impedance, with a frequency range capability of DC to 40 GHz. (See Section 4 for full specifications) WARRANTY Product is warranted to conform to all applicable specifications for a period of one (1) year from acceptance, or the relay cycle life, whichever comes first. Operation Manual, Part Number , Rev. A, June 26, 2013 Page 8

9 FRONT/REAR VIEW The figures below illustrate the front and rear power, power indicator and switch positions for the units. Switch configuration and rear panel as shown are for reference only. Figure 1 Series 8000 Front panel view Figure 2 Series 8000 Rear panel view, LAN Figure 3 Series 8000 Rear panel view, GPIB Operation Manual, Part Number , Rev. A, June 26, 2013 Page 9

10 SECTION 2 UNIT DEFAULTS This unit is shipped from the factory with the following default settings: Default IP Address (LAN units only): Default Timeout: 1,000 seconds Default GPIB Address(GPIB units only): 4 CONTROL COMMANDS An example of control commands is shown below. For your specific configuration, reference the addendum for your switch product. LOCATION SW POSITIONS CONNECTS TO SCPI COMMANDS S1 1 Open J3 (on Relay Control ROUTe:SWITch 1, 0 1 board) ROUTe:SWITch 1, 1 2 ROUTe:SWITch 1, 2 3 ROUTe:SWITch 1, 3 4 ROUTe:SWITch 1, 4 5 ROUTe:SWITch 1, 5 6 ROUTe:SWITch 1, 6 LOCATION SW POSITIONS CONNECTS TO SCPI COMMANDS S6 6 Open J8 (on Relay Control ROUTe:SWITch 6, 0 1 board) ROUTe:SWITch 6, 1 2 ROUTe:SWITch 6, 2 3 ROUTe:SWITch 6, 3 4 ROUTe:SWITch 6, 4 5 ROUTe:SWITch 6, 5 6 ROUTe:SWITch 6, 6 NOTE: The commands referred to in this manual assume that the switches are connected properly to the relay control board connectors. If the switches are physically moved to a different location in the front panel, the command parameters DO NOT change. If such a physical change is made, the user assumes the responsibility of properly identifying the switch locations. CAUTION Please consult Giga-tronics factory before making any changes in your equipment! Operation Manual, Part Number , Rev. A, June 26, 2013 Page 10

11 SWITCH CLOSURE, COUNTER, QUERY COMMANDS The SCPI commands required to set switch positions, query the switch count, and to save counters are listed below with an example switch configuration. These end user commands are always accessible. ROUTe:SWITch Sw, P Sets a switch to a desired position. Sw is the switch identification number, 1-6. P is the desired position as a decimal value. Sw Positions 1 0, 1, 2, 3, 4, 5, 6 6 0, 1, 2, 3, 4, 5, 6 NOTE: 0 = Open, or No Connection ROUTe:SWITch? Sw Returns switch position, current switch count, and switch identifier string. Sw is a number to identify the switch. The response is: Sw, position, count, ID. An example is: ROUTe:SWITch? 2 2, 5, , S/N ROUTe:SWITch:SAVe ROUTe:SWITch:SAVe? Saves all switch counter values to flash memory. The command only saves the current counter values. Queries the number of flash saves done via the ROUTe:SWITch:SAVe command, power fail and auto save intervals. Operation Manual, Part Number , Rev. A, June 26, 2013 Page 11

12 SECTION 3 The unit is equipped with a replaceable fuse on the AC power input module AC INPUT MODULE FUSE FUSE, 250V, TYPE T, SLO-BLO, 6.3 AMP POWER SUPPLY SPECIFICATIONS Universal Power Supply, 250W, 5V/30A & 12V/16.7A, W/FAN INPUT Parameter Conditions /Description Min Nom Max Units Input Frequency Hz Input Voltage / Auto-selectable VAC Input Current At VAC At VAC 8 4 A A Inrush Current Peak measured at 230 VAC at full load, cold start Peak measured at 115 VAC at full load, cold start A A Power Factor Passive power factor correction meets EN class A OUTPUT Parameter Conditions /Description Min Nom Max Units Transient Response Output voltage returns to within 1 % in less than 2.5 ms 2.5 ms for a 50 % load change. Peak transient does not exceed 5 % Overshoot Turn-on and turn-off overshoot shall not exceed 5 % 5% over nominal voltage Efficiency Measured at 230 VAC and full load 75 % Turn on Delay At 120 VAC 1 second Hold up Time At 120 VAC and 80 % of rated maximum load 20 ms PROTECTION CIRCUIT Parameter Conditions /Description Overload Current limiting starts at % of the rated output current in foldback mode and recovers automatically Short Circuit Output Over-voltage Over Temperature Short circuit can be continuous. Recovers automatically upon removal of shout Output is protected against over-voltage. Unit shuts down and latches when the voltage at output terminals exceeds 130 %. AC needs to be reset to restart the power supply Power Supply shuts down when temperature is in excess of 85 C. Auto Recovery Operation Manual, Part Number , Rev. A, June 26, 2013 Page 12

13 SECTION 4 RF SWITCH SPECIFICATIONS See your manual addendum for switch specifications. Operation Manual, Part Number , Rev. A, June 26, 2013 Page 13

14 SECTION 5 OUTLINE DRAWINGS Series 8000 OUTLINE DRAWING Note: Switch configuration as shown may different from your model Operation Manual, Part Number , Rev. A, June 26, 2013 Page 14

15 RF SWITCH FACE DETAIL 2.25 x 2.25 SP6T switch shown is typical, for reference only. All coax connector shall be tightened to the torque specified below. Connector Type Material Torque Value American Metric SMA, SMA 2.9 Stainless Steel 7 10 in-lbs N-m Operation Manual, Part Number , Rev. A, June 26, 2013 Page 15

16 Notes Operation Manual, Part Number , Rev. A, June 26, 2013 Page 16

17 Operation Manual, Part Number , Rev. A, June 26, 2013 Page 17