DIGITAL ANALOG TECHNOLOGY RFID

Transcription

1 DIGITAL ANALOG TECHNOLOGY RFID 334 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax

2 BL20 Modular fieldbus I/O ystem in IP20 BL20 General Page BL20 ystem concept 336 BL20 CODEY and I/O-AITANT 338 BL20 Electronic modules module code and colour code 340 BL20 Base modules type code 341 BL20 Combination options 342 BL20 ystem supply and power supply concept 344 BL20 Maximum system expansion and power supply 346 BL20 General technical data 348 BL20 pecial accessories 30 BL20 Gateways Gateways for PROFIBU-DP 34 Gateways for DeviceNet 36 Gateways for CANopen 38 Gateways for MODBU TCP 360 Multi-protocol interface for Ethernet 361 Gateways for EtherNet/IP 362 Gateways for PRFOFINET IO 364 Gateways for EtherCAT 36 BL20 Programmable Gateways Programmable gateways for MODBU TCP 366 Programmable gateways for EtherNet/IP 367 BL20 Electronic modules and related base modules Bus refeshing modules 368 Power feeding modules 370 Digital input modules 374 Analogue input modules 388 Digital output modules 400 Analogue output modules 422 R232 interface 430 R48/422 interface 432 I interface 434 Counter module 436 BL ident RFID modules 438 WIRE communication modules 442 BL20 Motor starter BL20 motor starter ystem concept 444 BL20 motor starter election guide direct starter 446 BL20 motor starter election guide reversing starter 448 BL20 motor starter Technical specification motor protection switches 40 BL20 motor starter Technical specification power contactors 41 BL20 motor starter Accessories 42 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 33 /0812

3 The BL20 I/O system The integrator for fieldbus, ident system, motor starter Gateway The system control The interface to the higher level control system Gateways e.g. for PROFIBU-DP, CANopen, DeviceNet, Ethernet/IP and Modbus TCP also available as economy version Optional CODEY programmable according to IEC Relieves higher-level controller and bus system I/O modules independent of the fieldbus Prefabricated function blocks e.g. for the RFID system BL ident Economy I/O extremely compact and competitively priced 8 or 16 I/Os in only 12. mm Integrated connection level with Pushin tension spring technology, no tools necessary Economy I/Os combinable with standard I/O slices BL ident, the RFID system Up to 8 RFID channels Pre-processing in programmable gateway relieves the higher-level controller. 336 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

4 tandard I/O multifunctional and system friendly Exchangeable electronic modules disconnection of field wiring is not necessary. Up to two neighbouring modules are exchangeable during normal system operation without disrupting system functions ingle or block modules with screw or cage clamp terminals I/O-AITANT Planning, configuration, commissioning and diagnostic software Based on FDT/DTM technology Available as freeware on Motor starter imple wiring 3 connection-slices per gateway Up to 16 devices per slice Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

5 CODEY Easy programming with CODEY according to IEC The programmable gateways become decentral control units with the CODEY programming software. The graphical programming interface supports all IEC programming languages tatement list ( TL) tructured Text (T) Ladder Diagram (LD) Continuous Function Chart (CFC) equential Function Chart (A) imple connection Fast and simple networking of heterogeneous systems tandard transmission protocols such as TCP/IP and UDP/IP Global network variables Bidirectional data exchange between CODEY systems No additional programming required Project planning and configuration Target upport Package as a driver for the target system Drag and Drop function for hardware configuration tandard editor for I/O configuration and parameterisation ymbolic display of variables for I/O addresses Numerous diagnostics and commissioning functions Function blocks e. g. for the RFID system BL ident Dataexchange via Ethernet 338 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

6 I/O-AITANT Easy parameterisation with the I/O-AITANT on the basis of FDT/DTM technology ystem configuration, parameterisation and diagnostics with a graphical interface based on FDT/DTM technology DTMs can be integrated in any FDT frame application for configuration, commissioning and maintenance I/O-AITANT and DTMs are available as freeware on Description The configuration software I/O-AITANT supports you in planning and implementation of your I/O system. No matter if you are online or offline, the I/O-AITANT simplifies configuration and parameterisation of the modules. This software is also extremely helpful in system set-up and testing. Functions upporting software tool election of the required modules Offline planning and configuration of BL20 modules Configuration, parameterisation and commissioning of individual modules Reading and setting of process data Commissioning help for testing the wiring and sensors without PLC Realistic display of configured BL20 components Automatic documentation of configured BL20 systems Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

7 BL20 Electronic modules code and colour code Electronic module code Marking Designation Examples GWBR Gateway with integrated supply BL20-GWBR-PBDP PBDP PROFIBU-DP BL20-GWBR-PBDP E ECONOMY modules BL20-E-8DI-24VDC-P BL20-8/-E-8 Number of channels BL20-E-8DI-24VDC-P BR Bus refreshing modules BL20-BR-24VDC-D PF, D Power feeding modules, with diagnostics BL20-PF-24VDC-D DI Digital input module BL20-2DI-24VDC-P N npn BL20-2DI-24VDC-N P pnp BL20-2DI-24VDC-P DO Digital output module BL20-2DO-24VDC-2A-P R Relay module BL20-2DO-R-NC CO Change over BL20-2DO-R-CO NC Normally closed BL20-2DO-R-NC NO Normally open BL20-2DO-R-NO AI Analogue input module BL20-1AI-U(-10/0...10VDC) PT/NI Analogue input module for the connection of resistance thermometers Ni100 BL20-2AI-PT/NI-2/3 and Ni1000 as well as Pt100, Pt00 and Pt1000 in 2-wire and 3-wire technology PI Analogue input module for the connection of thermocouples with BL20-2AI-THERMO-PI cold junction compensation AO Analogue output module BL20-1AO-I(0/4...20MA) CNT Counter module BL20-1CNT-24VDC Electronic modules Colour code Electronic module Gateway Bus refreshing modules Power feeding modules Power feeding modules 120/230 VAC Digital input modules Analogue input modules Digital output modules Analogue output modules Relay modules Technology modules (counter module) Colour code dusty grey dusty grey dusty grey orange brown light grey pigeon blue strawberry red pale green pastel orange zinc yellow 340 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

8 BL20 Base modules code B L T B B Example: BL20-3T-BB Device series (BL20) BL20 system Device design () lice design (B) Block design (P) Base module for power supply Number of connection levels (3) 3 connection levels level 3 (B) bridged conections (bridged connectors) technology (T) Tension spring connection () crew connection level 2 (B) bridged conections (bridged connectors) level 1 () non-bridged connections (single connectors) Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

9 BL20 Combination options Electronic modules and base modules Base modules with Ident-no. tension spring connection BL20-3T-BB BL20-3T-BC BL20-4T-BBC BL20-4T-BB BL20-4T-BC BL20-4T-BB-CJ BL20-6T-BBBB BL20-6T-BCBC BL20-B3T-BB BL20-B3T-BC BL20-B4T-BBC BL20-B6T-BBBB BL20-B6T-BCBC BL20-P3T-BB BL20-P3T-BB-B BL20-P4T-BBC Digital input modules Ident-no. BL20-2DI-120/230VAC-P BL20-4DI-24VDC-P BL20-4DI-24VDC-N BL20-4DI-NAMUR BL20-16DI-24VDC-P BL20-32DI-24VDC-P Analogue input modules BL20-2AI-I(0/4...20MA) BL20-2AI-U(-10/0...10VDC) BL20-2AI-PT/NI-2/ BL20-2AI-THERMO-PI BL20-4AI-U/I BL20-2AIH-I Digital output modules BL20-2DO-24VDC-0,A-N BL20-2DO-24VDC-2A-P BL20-2DO-120/230VAC-0.A BL20-4DO-24VDC-0,A-P BL20-16DO-24VDC-0,A-P BL20-32DO-24VDC-0,A-P Analogue output modules BL20-2AO-I(0/4...20MA) BL20-2AO-U(-10/0...10VDC) BL20-2AOH-I Relay modules BL20-2DO-R-NC BL20-2DO-R-NO BL20-2DO-R-CO Technology modules BL20-1R BL20-1R48/ BL20-1I BL20-P4T-BBC-B Page Power supply modules BL20-BR-24VDC-D BL20-PF-24VDC-D BL20-PF-120/230VAC-D BL ident RFID modules BL20-2RFID-A BL20-2RFID Base module with gateway power supply 2 Base module for module refresh within the station 342 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

10 Base modules with Ident-no. screw connections BL20-3-BB BL20-3-BC BL20-4-BBC BL20-4-BB BL20-4-BC BL20-4-BB-CJ BL20-6-BBBB BL20-6-BCBC BL20-B3-BB BL20-B3-BC BL20-B4-BBC BL20-B6-BBBB BL20-B6-BCBC BL20-P3-BB BL20-P3-BB-B BL20-P4-BBC BL20-P4-BBC-B Page ECONOMY modules Digital input modules series ECO (base module integrated) Page BL20-E-8DI-24VDC-P BL20-E-16DI-24VDC-P Digital output modules series ECO (base module integrated) BL20-E-8DO-24VDC-0,A-P BL20-E-16DO-24VDC-0,A-P Analogue input modules series ECO (base module integrated) BL20-E-8AI-U/I-4PT/NI Analogue output modules series ECO (base module integrated) BL20-E-4AO-U/I Technology modules series ECO (base module integrated) BL20-E-2CNT-2PWM WIRE communication module series ECO (base module integrated) BL20-E-1WIRE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

11 BL20 ystem supply General system power supply The BL20 system features two power circuits: The internal module bus feeds the module electronics and the gateway. The field supply feeds all connected fieldbus devices. Forming potential groups Bus-Refreshing modules as well as Power-Feeding modules can be used for the creation of potential groups. Modules with and 120/230 VAC field supply should not be used in the same potential group. The use of digital input modules for 120/230 VAC requires the creation of a separate potential group with the Power-Feeding module BL20-PF-120/230VAC-D. Module bus supply The voltage supply for the module bus is integrated in current BL20 gateways. If the module bus is not sufficiently supplied (max. 1. A), a second Refreshing-Module has to be applied see chapter upply concept on the next page. NOTE: Bus-Refreshing modules can not be used in combination with the Economy gateway for PROFIBU-DP. Field supply The field supply is provided by the gateway. A Power-Feeding module has to be used if the field supply of fieldbus nodes reaches 10 A or a new potential group is required (see section to the left). ystem planning For the planning of many complex BL20 stations, different factors have to be considered. For example rated current consumption of the modules, number of modules, parameters and data volume and possible restrictions imposed by the higher level fieldbus. The I/O-AITANT (p. 339), which can be downloaded from our website checks all relevant parameters and simplifies project planning considerably. The I/O-AITANT is also able to generate dimension drawings and documentation of the stations. Reading and setting of I/Os is also possible which proves very helpful for commissioning. Furthermore, module parameters can be set. 1 I MB : current via the module bus 2 I EI : electrical operating current (field supply) 344 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

12 BL20 Power supply concept tandard gateways (with integrated power supply) Power feeding module Bus refreshing module I MB I MB V MB V ys = Internal module bus = ystem supply V F1 = Field supply 1 V F2 = Field supply 2 I F1 I F2 I F1 I MBmax = 1. A I F1max = 10 A I F2max = 10 A Field supply Potential group I Field supply Potential group II Field supply Potential group III V ys() V F1() V F2(/120/230 VAC) V ys() V F1() Economy gateway for PROFIBU-DP (with integrated power supply) Power feeding module Power feeding module I MB V MB V ys = Internal module bus = ystem supply V F1 = Field supply 1 V F2 = Field supply 2 I F1 I F2 I F2 I MBmax = 1 A I F1max = 10 A I F2max = 10 A V ys() Field supply Potential group I V F1() V F2(/120/230 VAC) Field supply Potential group II Field supply Potential group III V F2(/120/230 VAC) Note: No application of bus refreshing module possible with Economy Gateway for PROFIBU-DP. Economy gateway for DeviceNet and CANopen (with integrated power supply) Power feeding module Bus refreshing module I MB I MB V MB V ys = Internal module bus = ystem supply V F1 = Field supply 1 V F2 = Field supply 2 I F1 I F2 I F1 I MBmax = 0.7 A I F1max = 10 A I F2max = 10 A Field supply Potential group I Field supply Potential group II Field supply Potential group III V ys() V F1() V F2(/120/230 VAC) V ys() V F1() Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 34 /0812

13 BL20 Maximum system extension Maximum system extension The maximum number of modules depends on the respective system configuration. Important thereby is the current consumption of the different I/O modules as well as the required address space and the fieldbus used. The tables below show some of the limitations for different fieldbuses. The configuration software I/O- AITANT takes these and all other relevant parameters into consideration and generates a warning message if appropriate. A BL20 station consists of a gateway and a maximum of 74 modules (approximately 1 m length of rail including end bracket and end plate). With the use of block modules, the maximum number of modules is correspondingly reduced (1 block module corresponds to approximately 8 slice modules). up to 74 module slices on a length of approx. 1 m 346 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

14 BL20 ystem assembly and power supply C-rail (cross connection) The C-rails run through all I/O base modules. The C-rail of the base modules for power distribution modules is mechanically separated; thus potentially isolating the adjoining supply groups. Using the C-rail as a protective earth The C-rail can be used as required in the application, for example, as a protective earth (PE). In this case, the PE connection of each power distribution module must be con- nected to the mounting rail via an additional PE terminal (see accessories), which is available as an accessory. Gateway BR 2 DO 2 DI 2 DO 2 DI PF 2 DO 2 DI 2 DO 2 DI PE terminal HLD DGND VP A B T HLD DGND VP A B C-rail (PE) C-rail (PE) 24 BBC BC BBC BC BB BBC BC BBC BC BB Access to C-rail Access to the C-rail is made via base modules with a C in their designation, for example: BL20-4T-BC. The corresponding connection level is indicated by a thick black line on all base modules for BL20 I/O modules. With base modules for power distribution modules, the black line is above the connection 24 only. This makes clear that the C-rail is separated from the adjoining potential group to its left. A maximum load of to the C-rail is allowed, but never 120/230 VAC. Using the C-rail with relay modules The C-rail can be used to supply a common voltage when relay modules are to be used. To accomplish this, the load voltage () is connected to a power distribution module with the base module BL20-P4x-BBC using either tension springs or screw connections. All the following relay modules are supplied with via the C-rail (see 1, Fig. below). The cross-connection of the individual relay modules is achieved using the cross-connector QVR (see 2, Fig. below). If the C-rail is to be used for the joint supply of voltage to relay modules, then there must subsequently be a further power distribution module used for the potential isolation of the following BL20 modules. The C-rail can again be put on other uses (for example, as a PE) once the potential isolation has been made. relay 1 relay n Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

15 BL20 General technical data BL20 modules technical data upply voltage/auxiliary power Nominal value (provided for other modules) Residual ripple according to EN Electrical isolation (U L ² to U Y ³/ U L to fieldbus/u Y to fieldbus) Ambient temperature yes, via opto-couplers Horizontal mounting ambient temperature 0 C Vertical mounting ambient temperature 0 C torage temperature -2 8 C Relative humidity to EN /EN 0178 Corrosive gases O₂ H₂ 9 % (indoor), Level RH-2, no condensation (storage at 4 C, no functional test) 10 ppm (rel. humidity < 7 %, no condensation) 1.0 ppm (rel. humidity < 7 %, no condensation) Vibration resistance 10 to 7 Hz, constant amplitude 0.07 mm, 1 g yes 7 to 10 Hz, constant amplitude 1 g yes Vibration type Vibration duration hock resistance as per IEC Repeated shock resistance as per IEC Drop and topple Fall height (weight < 10 kg) Fall height (weight 10 to 40 kg) Variable frequency runs at a rate of change of 1 octave/min 20 variable frequency runs per coordinate axis 18 shocks, half-sine 1 g peak value/11 ms, for both ±-directions per spatial coordinate 1000 shocks, half sine 2 g peak value/6 ms, for both ±-directions per spatial coordinate 1.0 m 0. m Test runs 7 Electromagnetic compatibility (EMC) as per EN (Industrial) tatic electricity as per EN Air discharge (direct) Relay discharge (indirect) Electromagnetic HF fields as per EN and ENV kv 4 kv 10 V/m Conducted interference, induced by HF fields as per 10 V EN Radiated interference as per EN (industrial) to EN 011 class A¹, group 1 ¹ Use in residential areas may lead to functional errors. Additional suppression measures are necessary! ² U L : Field supply ³ U Y : ystem supply 348 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

16 BL20 General technical data BL20 stations approvals and tests Approvals Ó È Í Tests (EN ) Cold DIN IEC , temperature -2 C, duration 96 h; device not operational Dry heat DIN IEC , temperature 8 C, duration 96 h; device not operational Damp heat, cyclic DIN IEC , temperature C, duration 2 cycles of 12 h; device operational Temperature change DIN IEC , temperature 0 to C, duration 2 cycles, temperature change per minute; device operational Operating life MTBF h Extraction/insertion cycles for electronics modules 20 Pollution level as per IEC 664 (EN 61131) 2 Degree of protection (IEC 6029/EN 6029) IP20 Base modules technical data BL20 Base module BL20 ECONOMY module Degree of protection (IEC 6029/EN 6029) IP20 IP20 tripped length 8 mm 8 mm Max. cross-section at terminal mm² mm² Conductors to be clamped e solid H 07V-U mm² mm² f stranded H 07V-K mm² mm² f with core-end ferrules to DIN 46228/1 (ferrules are crimped gas-tight) mm² mm² on wire end sleeves with plastic collar mm² mm² Finger test to IEC 947-1/1988 A1 A1 Rating data in accordance with VDE 0611 part 1/8.92/IEC / 1989 Rated voltage 20 V 20 V Rated current 17. A 17. A Rated cross-section 1. mm² 1. mm² Rated surge voltage 4 kv 4 kv Pollution degree 2 2 method in TOP direction Tension spring connector or screw terminal Tension spring connector Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

17 BL20 pecial accessories Figure Description Ident-No. Configuration, commissioning and diagnosticsoftware I/O-AITANT for modular fieldbus I/O systems freeware for download on R232 adapter cable for connection to configuration software I/O AITANT, 9-pole UB-D connector, cable length 2. m I/O-AITANT-Kabel-BL20/BL User manuals The user manual for BL20 systems is only available as PDF file and can be downloaded on 30 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

18 Designation Description (per packing unit) Ident-No. Labels for labelling electronic modules DIN A sheets, slice, perforated (laser print) 7 labels DIN A sheets, block, perforated (laser print) 6 labels BL20-LABEL/CHEIBE BL20-LABEL/BLOCK Markers for labeling base modules, color identification for clear recognition of potentials in the connection level of the base modules (strip of 10 6): blue red green black brown red/blue green/yellow white BL20-ANBZ-BL BL20-ANBZ-RT BL20-ANBZ-GN BL20-ANBZ-W BL20-ANBZ-BR BL20-ANBZ-RT/BL-BED BL20-ANBZ-GN/GE-BED BL20-ANBZ-W Jumpers for relays (QVR) for bridging the 4th connection level (14/24) of base modules for relays /10 pcs. 1 grid 2 grid 3 grid 4 grid grid 6 grid 7 grid 8 grid BL20-QV/1 BL20-QV/2 BL20-QV/3 BL20-QV/4 BL20-QV/ BL20-QV/6 BL20-QV/7 BL20-QV/ Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 31 /0812

19 BL20 pecial accessories Designation Description (per packing unit) Ident-No. End plate mechanical termination of the BL20 station on the right-hand side, included with gateways BL20-ABPL End bracket, black mechanical fixing of the BL20 station, 2 pcs., included with gateways BL20-WEW-3/2-W hield terminal hield terminal B311/KLBUE tension spring operating tool tension spring operating tool ZBW /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

20 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax /0812

21 Gateway for BL20 I/O system Interface for PROFIBU-DP incl. supply BL20-GW-DPV1 74,4 LED 114,8 0,6 Rotary coding switch for adjustment of the node address Degree of protection IP20 2 end brackets BL20-WEW3/2-W 1 end plate BL20-ABPL With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and PROFIBU-DPV0/DPV1 12 Mbps 9-pole sub-d female connector Ident-No. ystem power supply Field supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing range Fieldbus addressing ervice interface Fieldbus connection technology Voltage supply connection Fieldbus connection Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-GW-DPV / VDC VDC < 430 ma 10 A 1. A screw connection 9.6 kbps up to 12 Mbps rotary switches P/2 socket for I/O-AITANT 1 female sub-d connector screw connection external 3 0 to C Field supply/system supply 34 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

22 Gateway for BL20 I/O system Interface for PROFIBU-DP BL20-E-GW-DP 7 72,6 129, 33, DIP switch rotary for adjustment of the node address Degree of protection IP20 2 end brackets BL20-WEW3/2-W 1 end plate BL20-ABPL With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and PROFIBU-DPV0/DPV1 12 Mbit/s Push-in clamps Ident-No. ystem power supply Field supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing range Fieldbus addressing ervice interface Fieldbus connection technology Voltage supply connection Fieldbus connection Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-E-GW-DP / VDC VDC < 430 ma 10 A 1 A Push-in clamps 9.6 kbps up to 12 Mbps per DIP switch P/2 socket for I/O-AITANT push-in clamps push-in clamps per DIP switch 3 0 to C Field supply/system supply = Field supply = ystem supply Fieldbus connection Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 3 /0812

23 Gateway for BL20 I/O system Interface for DeviceNet incl. supply BL20-GWBR-DNET 74,4 LED 114,8 0,6 Rotary coding switch for adjustment of the node address Degree of protection IP20 2 end brackets BL20-WEW3/2-W 1 end plate BL20-ABPL With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and DeviceNet 12 / 20 / 00 kbps The connection to DeviceNet is established via an Open-tyle- Connector Ident-No. ystem power supply Field supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing range Fieldbus addressing ervice interface Fieldbus connection technology Voltage supply connection Fieldbus connection Operating temperature BL20-GWBR-DNET / VDC VDC < 20 ma 10 A 1. A screw connection 12/20/00 kbps, DIP switch rotary switches P/2 socket for I/O-AITANT open connector screw connection external 0 to C Field supply/system supply ystem supply V CAN_H hield CAN_L V - Gateway Field supply 2 DI 2 DO /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

24 Gateway for BL20 I/O system Interface for DeviceNet BL20-E-GW-DN 7 72,6 129, 33, DIP switch rotary for adjustment of the node address Degree of protection IP20 2 end brackets BL20-WEW3/2-W 1 end plate BL20-ABPL With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and DeviceNet 12 / 20 / 00 kbps The connection to DeviceNet is established via an Open-tyle- Connector Ident-No. ystem power supply Field supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing range Fieldbus addressing ervice interface Fieldbus connection technology Fieldbus connection Operating temperature BL20-E-GW-DN / VDC VDC < 20 ma 10 A 0.7 A Push-in clamps kbps 0 63 per DIP switch P/2 socket for I/O-AITANT open connector per DIP switch 0 to C Field supply/system supply U L GND L GND L V CAN H shield CAN L V Field supply Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 37 /0812

25 Gateway for BL20 I/O system Interface for CANopen incl. supply BL20-GWBR-CANOPEN 74,4 LED 114,8 0,6 Rotary coding switch for adjustment of the node address Degree of protection IP20 2 end brackets BL20-WEW3/2-W 1 end plate BL20-ABPL With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface between BL20 system and CAN bus 20 kbps up to 1000 kbps The connection to CANopen is established via an Open-tyle- Connector Ident-No. ystem power supply Field supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing range Fieldbus addressing ervice interface Fieldbus connection technology Voltage supply connection Fieldbus connection Operating temperature BL20-GWBR-CANOPEN / VDC VDC < 30 ma 10 A 1. A screw connection 20 to 1000 kbps, DIP switch rotary switches P/2 socket for I/O-AITANT open connector screw connection external 0 to C Field supply/system supply ystem supply V CAN_H hield CAN_L V - Gateway Field supply 2 DI 2 DO /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

26 Gateway for BL20 I/O system Interface for CANopen BL20-E-GW-CO 7 72,6 129, 33, DIP switch rotary for adjustment of the node address Degree of protection IP20 2 end brackets BL20-WEW3/2-W 1 end plate BL20-ABPL With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and CANopen 1 Mbps Push-in clamps Ident-No. ystem power supply Field supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing range Fieldbus addressing ervice interface Fieldbus connection technology Fieldbus connection Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-E-GW-CO / VDC VDC < 30 ma 10 A 0.7 A push-in clamps 20 kbps to 1 Mbps 1 63 per DIP switch P/2 socket for I/O-AITANT push-in clamps per DIP switch 3 0 to C Field supply/system supply = Field supply = ystem supply Fieldbus connection Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 39 /0812

27 Gateway for BL20 I/O system Interface for MODBU TCP incl. supply BL20-GW-EN 74,4 LED 114,8 0,6 Rotary coding switch for adjustment of the node address Degree of protection IP20 2 end brackets BL20-WEW3/2-W 1 end plate BL20-ABPL With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and MODBU TCP 10/100 Mbps RJ4 socket Ident-No. ystem power supply Field supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing ervice interface Fieldbus connection technology Voltage supply connection Operating temperature BL20-GW-EN / VDC VDC < 00 ma 10 A 1. A screw connection 10/100 Mbps rotary switch, BOOTP, DHCP, IO-AITANT P/2 socket for I/O-AITANT RJ4 socket screw connection 0 to C Field supply/system supply 360 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

28 Gateway for BL20 I/O system Multi-protocol interface for Ethernet BL20-E-GW-EN Ident-No. upply voltage Admissible range Rated current from module bus Max. system supply current Max. load current Io Voltage supply connection ystem data Transmission rate technology Ethernet Protocol detection/changeover ervice interface Web server Modbus TCP Addressing upported function codes Number of connections EtherNet/IP Addressing Quick Connect (QC) Device Level Ring (DLR) Number of connections PROFINET IO Addressing Conformance Class MinCycleTime Fast tartup Diagnostics Topology detection Automatic addressing Operating temperature 7 72,6 129, 33, BL20-E-GW-EN VDC < 200 ma 0.4 A 10 A push-in clamps 10/100 Mbps; Full/Half Duplex; Auto Negotiation; Auto Crossing 2 RJ4, female automatic Mini-UB, Ethernet in preparation tatic IP, BOOTP, DHCP FC1, FC2, FC3, FC4, FC, FC6, FC1, FC16, FC23 6 (available Q1/2013*) acc. to EtherNet/IP specification < 10 ms supported 6 (available Q1/2013*) DCP B (RT) 1 ms < 10 ms acc. to PROFINET IO Alarm Handling supported supported 0 to C DIP switch rotary for adjustment of the node address Degree of protection IP20 LEDs for display of supply voltage, common alarm and bus errors Multiprotocol interface between the BL20 system and the Ethernet protocols Modbus TCP and EtherNet/IP and PROFINET IO EtherNet/IP supports QuickConnect (QC) PROFINET IO supports fast start-up (FU) Integrated switch 10/100 Mbps Two RJ4 males for fieldbus connection Push-in clamps for connection of power supply Field supply/system supply ETH1 ETH2 U L GND L U Y GND Y Field supply ystem supply * The current device firmware supports Modbus TCP, the EtherNet/IP and PROFINET IO protocols will be included in phase 2 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

29 Gateway for BL20 I/O system Interface for EtherNet/IP supply inclusive BL20-GW-EN-IP 74,4 LED 114,8 0,6 Rotary coding switch for adjustment of the node address Degree of protection IP20 2 end brackets BL20-WEW3/2-W 1 end plate BL20-ABPL With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and EtherNet/IP 10/100 Mbps RJ4 socket Ident-No. ystem power supply Field supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing ervice interface Fieldbus connection technology Voltage supply connection Operating temperature BL20-GW-EN-IP / VDC VDC < 00 ma 10 A 1. A screw connection 10/100 Mbps rotary switch, BOOTP, DHCP, IO-AITANT P/2 socket for I/O-AITANT RJ4 socket screw connection 0 to C Field supply/system supply 362 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

30 Gateway for BL20 I/O system Interface for EtherNet/IP supply inclusive BL20-E-GW-EN-IP 7 72,6 129, 33, DIP switch rotary for adjustment of the node address Degree of protection IP20 2 end brackets BL20-WEW3/2-W 1 end plate BL20-ABPL With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and EtherNet/IP 10/100 Mbps Integrated switch 2 RJ4 socket Ident-No. ystem power supply Field supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing ervice interface Fieldbus connection technology Operating temperature Approvals BL20-E-GW-EN-IP / VDC VDC < 20 ma 10 A 0.4 A push-in clamps 10/100 Mbps per DIP switch Mini UB RJ4 socket 0 to C CE, culus, Zone2, ClassI, Div.2 Field supply/system supply ETH1 ETH2 U L GND L U Y GND Y Field supply ystem supply Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

31 Gateway for BL20 I/O system High-feature interface for PROFINET IO (RT/IRT) BL20-E-GW-PN 7 72,6 129, 33, Degree of protection IP20 LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and PROFINET IO (IRT) Interface between BL20 system and PROFINET IO RT/IRT upports topology recognition and LLDP Integrated switch 10/100 Mbps Two RJ4 males for fieldbus connection Push-in clamps for connection of power supply Ident-No. ystem power supply Admissible range Rated current from module bus Max. system supply current Max. load current I o Voltage supply connection ystem data Transmission rate technology Ethernet Protocol detection/changeover ervice interface Web server PROFINET Addressing Conformance Class MinCycleTime Fast tartup Diagnostics Topology detection Automatic addressing Media Redundancy Protocol (MRP) Max. number of I/O modules Operating temperature BL20-E-GW-PN VDC < 200 ma 0.8 A 10 A push-in clamps 10/100 Mbps; Full/Half Duplex; Auto Negotiation; Auto Crossing 2 RJ4, female automatic Mini UB in preparation DCP C (IRT) 1 ms < 10 ms acc. to PROFINET Alarm Handling supported supported in preparation 72 0 to C Field supply/system supply ETH1 ETH2 U L GND L U Y GND Y Field supply ystem supply 364 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

32 Gateway for BL20 I/O system Interface for EtherCAT BL20-E-GW-EC 7 72,6 Degree of protection IP20 LEDs for display of supply voltage, common alarm and bus errors Interface between the BL20 system and PROFINET IO (IRT) Interface between the BL20 system and EtherCAT Modular Device Profile (MDP) upport 129, 33, 10/100 Mbps, Auto MDIX Two RJ4 males for fieldbus connection Push-in clamps for connection of power supply Ident-No. ystem power supply Admissible range Rated current from module bus Max. system supply current Max. load current I o Voltage supply connection ystem data Transmission rate technology Ethernet Protocol detection/changeover ervice interface Web server EtherCAT Addressing MinCycleTime Diagnostics CAN over EtherCAT Max. number of I/O modules Operating temperature BL20-E-GW-EC / VDC VDC < 200 ma 0.8 A 10 A push-in clamps 10/100 Mbps; Full/Half Duplex; Auto Negotiation; Auto Crossing 2 RJ4, female automatic Mini UB in preparation automatic 20 µs CoE Emergencies, DiagnosisHistory acc. to Modular Device Profile 72 0 to C Field supply/system supply ETH1 ETH2 UL GNDL UY GNDY EtherCAT IN EtherCAT OUT Field supply ystem supply Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 36 /0812

33 Programmable gateway for the BL20 I/O system Interface for MODBU TCP incl. supply BL20-PG-EN 74,4 LED 114,8 0,6 Programmable acc.to IEC with CODEY Ethernet and R232 programmable interface 12 kbyte program memory 32 Bit RIC processor < 1 ms for 1000 instructions 3 decimally coded rotary switches Degree of protection IP20 With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface for MODBU TCP 10/100 Mbps Ident-No. ystem power supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing ervice interface Fieldbus connection technology Voltage supply connection PLC data Programming Released for CODEY version Programming languages Application tasks Number of POUs Programming interface Cycle time Program memory Data memory Input data Output data Non-volatile memory Operating temperature BL20-PG-EN VDC < 00 ma 10 A 1. A screw connection 10/100 Mbps rotary switch, BOOTP, DHCP, IO-AITANT P/2 socket for I/O-AITANT RJ4 socket screw connection CODEY V2.3 V IEC (IL, LD, FBD, FC, T) R232 interface, Ethernet RIC 32 bit < 1 ms for 1000 IL commands (without I/O cycle) 12 kbyte 12 kbyte 4 kbyte 4 kbyte 16 kbyte 0 to C Field supply/system supply 366 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

34 Programmable gateway for the BL20 I/O system Interface for EtherNet/IP supply inclusive BL20-PG-EN-IP 74,4 LED 114,8 0,6 Programmable acc.to IEC with CODEY Ethernet and R232 programmable interface 12 kbyte program memory 32 Bit RIC processor < 1 ms for 1000 instructions 3 decimally coded rotary switches Degree of protection IP20 With integrated supply LEDs for display of supply voltage, common alarm and bus errors Interface for EtherNet/IP 10/100 Mbps Ident-No. ystem power supply Admissible range Rated current from module bus Max. field supply current Max. system supply current Voltage supply connection Fieldbus transmission rate Fieldbus addressing ervice interface Fieldbus connection technology Voltage supply connection PLC data Programming Released for CODEY version Programming languages Application tasks Number of POUs Programming interface Cycle time Program memory Data memory Input data Output data Non-volatile memory Operating temperature BL20-PG-EN-IP VDC < 00 ma 10 A 1. A screw connection 10/100 Mbps rotary switch, BOOTP, DHCP, IO-AITANT P/2 socket for I/O-AITANT RJ4 socket screw connection CODEY V2.3 V IEC (IL, LD, FBD, FC, T) R232 interface, Ethernet RIC 32 bit < 1 ms for 1000 IL commands (without I/O cycle) 12 kbyte 12 kbyte 4 kbyte 4 kbyte 16 kbyte 0 to C Field supply/system supply Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

35 BL20 electronic module Bus refreshing module with diagnostics BL20-BR-24VDC-D 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of system status, field supply and diagnostic information Can be used to form potential groups Power supply of the BL20 I/O module and the gateway with a nominal system voltage of VDC via the internal module bus Field supply featuring a rated voltage of Ident-No. ystem power supply Field supply Admissible range Max. field supply current Max. system supply current Number of diagnostic bits Operating temperature BL20-BR-24VDC-D / VDC VDC 10 A 1. A 4 0 to C 368 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

36 BL20 electronic module Bus refreshing module with diagnostics BL20-BR-24VDC-D Compatible base modules Dimensions 117, BL20-P3T-BB Tension spring connection, with gateway supply BL20-P3-BB crew connection, with gateway supply Is placed on the right side of the gateway (for gateways without integrated power supply). F BL20-P3T-BB-B Tension spring connection, without gateway supply BL20-P3-BB-B crew connection, without gateway supply Is applied to bigger BL20 systems in order to supply the module bus if required. Dimensions BL20-P4T-BBC Tension spring connection, C rail, with gateway supply BL20-P4-BBC crew connection, C rail, with gateway supply Is placed on the right side of the gateway (for gateways without integrated power supply). F BL20-P4T-BBC-B Tension spring connection, C rail, without gateway supply BL20-P4-BBC-B crew connection, C rail, without gateway supply Is applied to bigger BL20 systems in order to supply the module bus if required. F186 - Wiring diagram Module bus supply F187 - Wiring diagram Module bus supply Field supply Field supply PE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

37 BL20 electronic module Power feeding module with diagnostics BL20-PF-24VDC-D 73,1 LED 74,1 117,6 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of system status, field supply and diagnostic information Can be used to form potential groups Field supply featuring a rated voltage of 14, Ident-No. Field supply Rated current from module bus Max. field supply current Number of diagnostic bits Operating temperature BL20-PF-24VDC-D < 28 ma 10 A 4 0 to C 370 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

38 BL20 electronic module Power feeding module with diagnostics BL20-PF-24VDC-D Compatible base modules Dimensions 117, BL20-P3T-BB Tension spring connection BL20-P3-BB crew connection F188 Dimensions BL20-P4T-BBC Tension spring connection, access to C rail BL20-P4-BBC crew connection, access to C rail F189 F188 - Wiring diagram F189 - Wiring diagram PE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

39 BL20 electronic module Power feeding module with diagnostics BL20-PF-120/230VAC-D 73,1 LED 74,1 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of system status, field supply and diagnostic information Can be used to form potential groups Field supply featuring a rated voltage of 120/230 VAC 117,6 14, Ident-No. Field supply Rated current from module bus Max. field supply current Number of diagnostic bits Operating temperature BL20-PF-120/230VAC-D / 230 VAC < 2 ma 10 A 4 0 to C 372 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

40 BL20 electronic module Power feeding module with diagnostics BL20-PF-120/230VAC-D Compatible base modules Dimensions 117, BL20-P3T-BB Tension spring connection BL20-P3-BB crew connection F190 Dimensions BL20-P4T-BBC Tension spring connection, access to C rail BL20-P4-BBC crew connection, access to C rail F191 F190 - Wiring diagram F Wiring diagram N N L L PE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

41 BL20 electronic module 2 digital inputs BL20-2DI-120/230VAC-P 73,1 LED 74,1 117,6 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 digital inputs, 120/230 VAC 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Low level signal voltage High level signal voltage Frequency range Low level signal current High level signal current Input delay Electrical isolation Operating temperature BL20-2DI-120/230VAC-P / 230 VAC < 20 ma < 28 ma < 1 W 0 V 20 VAC 79 VAC 26 VAC 47. Hz to 63 Hz 0 ma 1 ma 3 ma 10 ma < 20 ms electronics for the field level 0 to C 374 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

42 BL20 electronic module 2 digital inputs BL20-2DI-120/230VAC-P Compatible base modules Dimensions 117, BL20-3T-BB Tension spring connection BL20-3-BB crew connection F196 Dimensions BL20-4T-BBC Tension spring connection, access to C rail BL20-4-BBC crew connection, access to C rail F197 F196 - Wiring diagram F197 - Wiring diagram Bit 0 BN 11 BU N 12 L BN BU N L Bit 1 Bit 0 BN 11 BU N 12 L 13 GNYE PE BN Bit 1 BU N L PE GNYE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 37 /0812

43 BL20 electronic module 4 digital inputs BL20-4DI-24VDC-P 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 4 digital inputs, pnp Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Low level signal voltage High level signal voltage Low level signal current High level signal current Input delay Electrical isolation Operating temperature BL20-4DI-24VDC-P < 40 ma < 28 ma < 1 W pnp -30 V V 1 V 30 V 0 ma 1. ma 2 ma 10 ma < 0.2 ms electronics for the field level 0 to C 376 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

44 BL20 electronic module 4 digital inputs BL20-4DI-24VDC-P Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F198 Dimensions 14, BL20-6T-BBBB Tension spring connection BL20-6-BBBB crew connection F199 F198 - Wiring diagram F199 - Wiring diagram Bit 0 Bit 1 Bit Bit Bit 2 Bit 3 Bit 2 Bit Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

45 BL20 electronic module 4 digital inputs BL20-4DI-24VDC-N 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 4 digital inputs, npn Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Low level signal voltage High level signal voltage Low level signal current High level signal current Input delay Electrical isolation Operating temperature BL20-4DI-24VDC-N < 40 ma < 28 ma < 1 W npn > 13 V 0 V V ma ma < 0.2 ms electronics for the field level 0 to C 378 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

46 BL20 electronic module 4 digital inputs BL20-4DI-24VDC-N Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F200 Dimensions 14, BL20-6T-BBBB Tension spring connection BL20-6-BBBB crew connection F201 F200 - Wiring diagram F201 - Wiring diagram Bit 0 Bit 1 Bit Bit Bit 2 Bit 3 Bit 2 Bit Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

47 BL20 electronic module 4 digital inputs BL20-4DI-NAMUR 73,1 LED 74,1 117,6 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 4 NAMUR inputs acc. to EN , Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type No-load voltage Input - status Input wire-break Input - short-circuit Input delay Electrical isolation Operating temperature BL20-4DI-NAMUR < 30 ma < 40 ma < 1 W NAMUR according to EN VDC switch on threshold: 1.74 ma switch off threshold: 1.4 ma switch on threshold: 0.08 ma switch off threshold: 0.12 ma switch on threshold: 6.2 ma switch off threshold:.9 ma 0.2 or 2. ms electronics for the field level 0 to C 380 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

48 BL20 electronic module 4 digital inputs BL20-4DI-NAMUR Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F200 F200 - Wiring diagram Bit Bit Bit Bit Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

49 BL20 Economy Module 8 digital inputs BL20-E-8DI-24VDC-P LED 73,1 72,6 Independent of the type of fieldbus used Electronics and connection technology in an single housing Tension spring connection technology Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 8 digital inputs, pnp Ident-No. Number of channels Rated voltage from the supply terminal Admissible range Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Low level signal voltage High level signal voltage Low level signal current High level signal current Input delay Electrical isolation Operating temperature BL20-E-8DI-24VDC-P VDC < 2 ma < 1 ma < 1. W pnp -30 V V 11 V 30 V -1 ma 1. ma 2 ma ma < 0.2 ms electronics for the field level 0 to C Terminal connection GND 382 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

50 BL20 Economy Module 16 digital inputs BL20-E-16DI-24VDC-P LED 74, 72,6 160 Independent of the type of fieldbus used Electronics and connection technology in an single housing Tension spring connection technology Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 16 digital inputs, pnp Ident-No. Number of channels Rated voltage from the supply terminal Admissible range Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Low level signal voltage High level signal voltage Low level signal current High level signal current Input delay Electrical isolation Operating temperature BL20-E-16DI-24VDC-P VDC < 3 ma < 1 ma < 1. W pnp -30 V V 11 V 30 V -1 ma 1. ma 2 ma ma < 0.3 ms electronics for the field level 0 to C Terminal connection GND Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

51 BL20 electronic module 16 digital inputs BL20-16DI-24VDC-P 73,1 LED 117,6 14, 74,1 100,8 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 16 digital inputs, pnp Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Low level signal voltage High level signal voltage Low level signal current High level signal current Input delay Electrical isolation Operating temperature BL20-16DI-24VDC-P < 40 ma < 4 ma < 2. W pnp -30 V V 1 V 30 V 0 ma 1. ma 2 ma 10 ma < 0.2 ms electronics for the field level 0 to C 384 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

52 BL20 electronic module 16 digital inputs BL20-16DI-24VDC-P Compatible base modules Dimensions 117, BL20-B3T-BB Tension spring connection BL20-B3-BB crew connection F ,8 Dimensions BL20-B4T-BBC Tension spring connection, access to C rail BL20-B4-BBC crew connection, access to C rail F ,8 F203 - Wiring diagram F204 - Wiring diagram Bit Bit 0 Bit 1 PE PE Bit Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 38 /0812

53 BL20 electronic module 32 digital inputs BL20-32DI-24VDC-P 73,1 LED 117,6 14, 74,1 100,8 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 32 digital inputs, pnp Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Low level signal voltage High level signal voltage Low level signal current High level signal current Input delay Electrical isolation Operating temperature BL20-32DI-24VDC-P < 30 ma < 4 ma < 4.2 W pnp -30 V V 1 V 30 V < 1. ma 2 ma 10 ma < 0.2 ms electronics for the field level 0 to C 386 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

54 BL20 electronic module 32 digital inputs BL20-32DI-24VDC-P Compatible base modules Dimensions 14, BL20-B6T-BBBB Tension spring connection BL20-B6-BBBB crew connection F20 100,8 F20 - Wiring diagram... Bit 0 Bit Bit 16 Bit Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

55 BL20 electronic module 2 analog inputs BL20-2AI-I(0/4...20MA) 73,1 LED 74,1 117,6 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 analog inputs 0/4 20 ma 14, Ident-No. Number of channels Rated voltage from the supply terminal Max. input current Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Input resistance Max. input current Electrical isolation Maximum limiting frequency, analog Basic fault limit at 23 C Repeatability Temperature coefficient Resolution Measuring principle Measured-value display Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-2AI-I(0/4...20MA) ma < 12 ma < 3 ma < 1 W 0/4 20 ma < ma electronics for the field level < 0 Hz < 0.2 % 0.0 % < 300 ppm/ C of full scale 16 Bit Delta igma 16 bit signed integer 12 bit full range left justified to C 388 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

56 BL20 electronic module 2 analog inputs BL20-2AI-I(0/4...20MA) Compatible base modules Dimensions 117, BL20-3T-BB Tension spring connection with external sensor supply BL20-3-BB crew connection with external sensor supply F210 Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F211, F212 F210 - Wiring diagram F211-2-wire technology F212-3-wire technology U/I U/I h h 23 U/I U/I I I h h U/I U/I h h Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

57 BL20 electronic module 2 analog inputs BL20-2AIH-I 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 analog inputs 0/4 20 ma HART Ident-No. Number of channels Rated voltage from the supply terminal Max. input current Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Input resistance Max. input current Electrical isolation Maximum limiting frequency, analog Basic fault limit at 23 C Repeatability Temperature coefficient Resolution Measuring principle Measured-value display Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-2AIH-I ma < 20 ma < 30 ma < 1 W 0/4 20 ma > ma 00 V electronics to field level, 00 V channel to channel < 0 Hz < 0.1 % 0.1 % < 10 ppm/ C of full scale 16 Bit Delta igma 16 bit signed integer,ne43(pa), Extended to C 390 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

58 BL20 electronic module 2 analog inputs BL20-2AIH-I Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F271, F272 F272-2-wire technology F271-4-wire technology Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

59 BL20 electronic module 2 analog inputs BL20-2AI-U(-10/0...10VDC) 73,1 LED 74,1 117,6 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 analog input -10/0 10 VDC 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Input resistance Max. input voltage Electrical isolation Maximum limiting frequency, analog Basic fault limit at 23 C Repeatability Temperature coefficient Resolution Measuring principle Measured-value display Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-2AI-U(-10/0...10VDC) < 12 ma < 3 ma < 1 W -10/0 10 VDC < 98, 3 V constant electronics for the field level < 0 Hz < 0.2 % 0.0 % < 10 ppm/ C of full scale 16 Bit Delta igma 16 bit signed integer 12 bit full range left justified to C 392 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

60 BL20 electronic module 2 analog inputs BL20-2AI-U(-10/0...10VDC) Compatible base modules Dimensions 117, BL20-3T-BB Tension spring connection with external sensor supply BL20-3-BB crew connection with external sensor supply F210 Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F211, F212 F210 - Wiring diagram F211-2-wire technology F212-3-wire technology U/I U/I h h 23 U/I U/I I I h h U/I U/I h h Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

61 BL20 electronic module 2 analog inputs for temperature measurement BL20-2AI-PT/NI-2/3 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 analog inputs for PT100, PT00 and PT1000 as well as for Ni100 and Ni1000 Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Electrical isolation Basic fault limit at 23 C Repeatability Temperature coefficient Resolution Measured-value display Cycle time Measuring current Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-2AI-PT/NI-2/ < 30 ma < 4 ma < 1 W PT100, PT00, PT1000, Ni100, Ni1000 electronics for the field level < 0.2 % 0.0 % < 300 ppm/ C of full scale 16 Bit 16 bit signed integer 12 bit full range left justified < 130 ms < 1 ma to C 394 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

62 BL20 electronic module 2 analog inputs for temperature measurement BL20-2AI-PT/NI-2/3 Compatible base modules Dimensions 117, BL20-3T-BB Tension spring connection BL20-3-BB crew connection F213 Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F214 F213-2-wire technology F214-3-wire technology I I I I é I é é é I I I Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 39 /0812

63 BL20 electronic module 2 analog inputs for temperature measurement BL20-2AI-THERMO-PI 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 analog inputs for connection of thermoelements, types B, E, J, K, N, R, and T Base module with internal cold junction point compensation Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Electrical isolation Voltage resolution Basic fault limit at 23 C Repeatability Temperature coefficient Resolution Measured-value display Cycle time Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-2AI-THERMO-PI < 30 ma < 4 ma < 1 W types B, E, J, K, N, R,, T electronics for the field level -0mV: < 2µV < 0.2 % 0.0 % < 300 ppm/ C of full scale 16 Bit 16 bit signed integer 12 bit full range left justified < 60 ms to C 396 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

64 BL20 electronic module 2 analog inputs for temperature measurement BL20-2AI-THERMO-PI Compatible base modules Dimensions BL20-4T-BB-CJ Tension spring connection BL20-4-BB-CJ crew connection F21 F21 - Wiring diagram i PT a PT i Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

65 BL20 electronic module 4 analog inputs BL20-4AI-U/I 73,1 LED 74,1 117,6 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 4 analog inputs 0/4 20 ma or 10/0 10 VDC electable per channel 14, Ident-No. Number of channels Rated voltage from the supply terminal Max. input current Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Input resistance Max. input current Max. input voltage Electrical isolation Maximum limiting frequency, analog Basic fault limit at 23 C Repeatability Temperature coefficient Resolution Measuring principle Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-4AI-U/I ma < 20 ma < 0 ma < 1 W 0/4 20 ma or -10/0 10 VDC < 62 Ω (current) or > 98. kω (voltage) 0 ma 3 V constant electronics for the field level < 20 Hz < 0.3 % 0.0 % < 300 ppm/ C of full scale 16 Bit Delta igma to C 398 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

66 BL20 electronic module 4 analog inputs BL20-4AI-U/I Compatible base modules Dimensions 14, BL20-6T-BCBC Tension spring connection BL20-6-BCBC crew connection F216, F217, F218 F216-2-wire technology F217-3-wire technology F218-4-wire technology Channel 1 UL or BR/PF terminal I h 12 Channel 3 13 UL or BR/PF terminal I h h h Channel 2 UL or BR/PF terminal 13 I Channel 4 UL or BR/PF terminal 13 I Channel 1 UL or BR/PF terminal 13 Channel 3 UL or BR/PF terminal 13 U/I h 13 U/I h 16 U/I h 23 U/I h Channel 2 UL or BR/PF Klemme 13 Channel 4 UL or BR/PF terminal 13 Channel 1 U/I U/I Channel 3 U/I U/I h h h h 26 Channel 2 U/I U/I Channel 4 U/I U/I Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

67 BL20 electronic module 8 2-wire analog inputs U/I resp. 4 2/3-wire PT/NI inputs BL20-E-8AI-U/I-4PT/NI Conversion time LED 73,1 Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs Input type Input resistance Max. input current Max. input voltage Basic fault limit at 23 C Temperature coefficient Resolution Measured-value display Number of diagnostic bytes Number of parameter bytes Operating temperature 72,6 BL20-E-8AI-U/I-4PT/NI /4 < 3 ma < 3 ma < 1 W 0/4 20 ma, -10/0 10 VDC, PT100, PT200, PT00, PT1000, NI100, NI1000, 0 20 Ω, Ω, Ω, Ω, Ω < 62 Ω (current) or > 98. kω (voltage) 0 ma -20 VDC < U < 20 VDC (externally supplied) < 0.2 % < 200 ppm/ C of full scale 16 Bit 16 bit signed integer 12 bit full range left justified < (44 [number of channels being activated during parametrization]) ms to C Independent of the type of fieldbus and connection technology used Electronics and connection technology in an single housing Tension spring connection technology Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 8 2-wire analog inputs U/I Passive inputs external power supply 0 20mA, 4 20mA,-10 10VDC or 0 10VDC, selectable per channel, resp. 4PT/NI inputs (always 2 analog inputs are combined to a PT/Ni 2/3-wire input) Terminal connection U/I PT/NI 2-wire 2-wire 3-wire I I 1 é é 2 I I I I 3 é é 4 I I I I é é 6 I I I I 7 é é 8 I I /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

68 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax /0812

69 BL20 electronic module 2 digital outputs BL20-2DO-24VDC-0.A-N 73,1 LED 74,1 117,6 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 digital outputs, 0. A max. npn 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Output voltage Output current per channel Output delay Load type Load resistance, resistive Load resistance, inductive Lamp load witching frequency, resistive Inductive switching frequency witching frequency, lamp load hort-circuit protection imultaneity factor Electrical isolation Number of diagnostic bits BL20-2DO-24VDC-0.A-N < 20 ma < 32 ma < 1 W npn 0. A 0.1 ms resistive, inductive, lamp load > 48 ò < 1.2 H < 12 W < 100 Hz < 2 Hz < 10 Hz yes 1 electronics for the field level 2 Operating temperature 0 to C 402 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

70 BL20 electronic module 2 digital outputs BL20-2DO-24VDC-0.A-N Compatible base modules Dimensions 117, BL20-3T-BC Tension spring connection, access to C rail BL20-3-BC crew connection, access to C rail F221 Dimensions BL20-4T-BC Tension spring connection, access to C rail BL20-4-BC crew connection, access to C rail F222 F221 - Wiring diagram F222 - Wiring diagram Bit 0 Bit 1 Bit Bit 1 PE PE PE PE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

71 BL20 electronic module 2 digital outputs BL20-2DO-24VDC-2A-P 73,1 LED 74,1 117,6 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 digital outputs, 2 A max. pnp 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Output voltage Output current per channel Output delay Load type Load resistance, resistive Load resistance, inductive Lamp load witching frequency, resistive witching frequency, lamp load hort-circuit protection imultaneity factor Electrical isolation Number of diagnostic bits BL20-2DO-24VDC-2A-P < 0 ma < 33 ma < 1 W pnp 2 A 0.1 ms resistive, inductive, lamp load > 12 ò < 1.2 H < 6 W < 000 Hz < 10 Hz yes 1 electronics for the field level 2 Operating temperature 0 to C 404 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

72 BL20 electronic module 2 digital outputs BL20-2DO-24VDC-2A-P Compatible base modules Dimensions 117, BL20-3T-BC Tension spring connection, access to C rail BL20-3-BC crew connection, access to C rail F219 Dimensions BL20-4T-BC Tension spring connection, access to C rail BL20-4-BC crew connection, access to C rail F220 F219 - Wiring diagram F220 - Wiring diagram Bit 0 Bit Bit Bit 1 PE PE PE PE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 40 /0812

73 BL20 electronic module 2 digital outputs BL20-2DO-120/230VAC-0.A 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 digital outputs, 120/230 VAC 0. A max. Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output voltage Output current per channel Output delay Load type Load resistance, resistive Load resistance, inductive hort-circuit protection imultaneity factor Electrical isolation Number of diagnostic bits Operating temperature BL20-2DO-120/230VAC-0.A / 230 VAC < 20 ma < 3 ma < 1 W 120 / 230 VAC 0. A 0.1 ms resistive, inductive, lamp load > 48 ò < 1.2 H yes 1 electronics for the field level 2 0 to C 406 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

74 BL20 electronic module 2 digital outputs BL20-2DO-120/230VAC-0.A Compatible base modules Dimensions 117, BL20-3T-BC Tension spring connection, access to C rail BL20-3-BC crew connection, access to C rail F219 Dimensions BL20-4T-BC Tension spring connection, access to C rail BL20-4-BC crew connection, access to C rail F220 F219 - Wiring diagram F220 - Wiring diagram Bit 0 Bit Bit Bit 1 PE PE PE PE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

75 BL20 electronic module relay module, 2 normally open BL20-2DO-R-NO 73,1 LED 74,1 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 normally open channels 117,6 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Load type Rated load voltage imultaneity factor Life at 230 VAC, A Life at 230 VAC, 0.A Output current with DC voltage (resistive) Electrical isolation Operating temperature BL20-2DO-R-NO , normally open < 20 ma < 28 ma < 1 W resistive, inductive, lamp load 230/30 VAC/DC see load limit curve electronics for the field level 0 to C Load limit curve 10 3 U [V] ,1 1 I [A] /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

76 BL20 electronic module relay module, 2 normally open BL20-2DO-R-NO Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection With externally applied supply and cross connected root 1) Jumpered in the electronics 2) cross-connection via QVR in the base F223, F22 Dimensions BL20-4T-BC F224, F226 Tension spring connection BL20-4-BC crew connection With supply via C rail and cross connected root 1) C rail 2) cross-connection via QVR in the base; max. 8 relay modules F223 - Wiring diagram F224 - Wiring diagram F22 - module wiring diagram F226 - module wiring diagram R R2 Power Relay 1 feeding R1 Relay n R2 R2 23 a R NO 0 RT NO 1 Electronics module RT b VDC Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

77 BL20 electronic module relay module, 2 normally closed BL20-2DO-R-NC 73,1 LED 74,1 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 normally closed channels 117,6 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Load type Rated load voltage imultaneity factor Life at 230 VAC, A Life at 230 VAC, 0.A Output current with DC voltage (resistive) Electrical isolation Operating temperature BL20-2DO-R-NC , normally closed < 20 ma < 28 ma < 1 W resistive, inductive, lamp load 230/30 VAC/DC see load limit curve electronics for the field level 0 to C Load limit curve 10 3 U [V] ,1 1 I [A] /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

78 BL20 electronic module relay module, 2 normally closed BL20-2DO-R-NC Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection With externally applied supply and cross connected root 1) Jumpered in the electronics 2) cross-connection via QVR in the base F223, F227 Dimensions BL20-4T-BC F224, F228 Tension spring connection BL20-4-BC crew connection With supply via C rail and cross connected root 1) C rail 2) cross-connection via QVR in the base; max. 8 relay modules F223 - Wiring diagram F224 - Wiring diagram F227 - module wiring diagram F228 - module wiring diagram Power Relay 1 feeding Relay n R R R R VDC Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

79 BL20 electronic module relay module, 2 change-over BL20-2DO-R-CO 73,1 LED 74,1 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 change-over channels 117,6 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Load type Rated load voltage imultaneity factor Life at 230 VAC, A Life at 230 VAC, 0.A Output current with DC voltage (resistive) Electrical isolation Operating temperature BL20-2DO-R-CO , change-over, galvanically isolated < 20 ma < 28 ma < 1 W resistive, inductive, lamp load 230/30 VAC/DC see load limit curve electronics for the field level 0 to C Load limit curve 10 3 U [V] ,1 1 I [A] /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

80 BL20 electronic module relay module, 2 change-over BL20-2DO-R-CO Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F229, F230 F229 - Wiring diagram F230 - module wiring diagram R11 R21 R R Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

81 BL20 electronic module 4 digital outputs BL20-4DO-24VDC-0.A-P 73,1 LED 74,1 117,6 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 4 digital outputs, 0. A max. pnp 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Output voltage Output current per channel Output delay Load type Load resistance, resistive Load resistance, inductive Lamp load witching frequency, resistive Inductive switching frequency witching frequency, lamp load hort-circuit protection imultaneity factor Electrical isolation Number of diagnostic bits BL20-4DO-24VDC-0.A-P < 2 ma < 30 ma < 1 W pnp 0. A 0.2 ms resistive, inductive, lamp load > 48 ò < 1.2 H < 6 W < 000 Hz < 2 Hz < 10 Hz yes 1 electronics for the field level 1 Operating temperature 0 to C 414 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

82 BL20 electronic module 4 digital outputs BL20-4DO-24VDC-0.A-P Compatible base modules Dimensions BL20-4T-BC Tension spring connection, access to C rail BL20-4-BC crew connection, access to C rail F231 Dimensions 14, BL20-6T-BCBC Tension spring connection, access to C rail BL20-6-BCBC crew connection, access to C rail F232 F231 - Wiring diagram F232 - Wiring diagram Bit Bit Bit PE PE Bit Bit Bit PE PE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 41 /0812

83 BL20 Economy Module 8 digital outputs BL20-E-8DO-24VDC-0.A-P LED 73,1 72,6 Independent of the type of fieldbus used Electronics and connection technology in an single housing Tension spring connection technology Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 8 digital outputs, 0. A max. pnp Ident-No. Number of channels Rated voltage from the supply terminal Admissible range Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Output voltage Output current per channel Output delay Load type Load resistance, resistive Lamp load witching frequency, resistive witching frequency, lamp load hort-circuit protection imultaneity factor Electrical isolation Operating temperature BL20-E-8DO-24VDC-0.A-P VDC < 3 ma < 1 ma < 1. W pnp 0. A 0.3 ms resistive, inductive, lamp load > 48 ò < 6 W < 100 Hz < 10 Hz yes 1 electronics for the field level 0 to C Terminal connection GND 416 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

84 BL20 Economy Module 16 digital outputs BL20-E-16DO-24VDC-0.A-P LED 74, 72,6 160 Independent of the type of fieldbus used Electronics and connection technology in an single housing Tension spring connection technology Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 16 digital outputs, 0. A max. pnp Ident-No. Number of channels Rated voltage from the supply terminal Admissible range Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Output voltage Output current per channel Output delay Load type Load resistance, resistive Lamp load witching frequency, resistive witching frequency, lamp load hort-circuit protection imultaneity factor Electrical isolation Operating temperature BL20-E-16DO-24VDC-0.A-P VDC < 3 ma < 2 ma < 1. W pnp 0. A 0.3 ms resistive, inductive, lamp load > 48 ò < 6 W < 100 Hz < 10 Hz yes 0. electronics for the field level 0 to C Terminal connection GND Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

85 BL20 electronic module 16 digital outputs BL20-16DO-24VDC-0.A-P 73,1 LED 117,6 14, 74,1 100,8 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 16 digital outputs, 0. A max. pnp Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Output voltage Output current per channel Output delay Load type Load resistance, resistive Load resistance, inductive Lamp load witching frequency, resistive hort-circuit protection imultaneity factor Electrical isolation Number of diagnostic bits Operating temperature BL20-16DO-24VDC-0.A-P < 0 ma < 120 ma < 4 W pnp 0. A 0.1 ms resistive, inductive, lamp load > 48 ò < 1.2 H < 3 W < 100 Hz yes 1 electronics for the field level 4 0 to C 418 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

86 BL20 electronic module 16 digital outputs BL20-16DO-24VDC-0.A-P Compatible base modules Dimensions 117, BL20-B3T-BC Tension spring connection, access to C rail BL20-B3-BC crew connection, access to C rail F ,8 F233 - Wiring diagram Bit 0 PE PE Bit 1 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

87 BL20 electronic module 32 digital outputs BL20-32DO-24VDC-0.A-P 73,1 LED 117,6 14, 74,1 100,8 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 32 digital outputs, 0. A max. pnp Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Output voltage Output current per channel Output delay Load type Load resistance, resistive Load resistance, inductive Lamp load witching frequency, resistive hort-circuit protection imultaneity factor Electrical isolation Number of diagnostic bits Operating temperature BL20-32DO-24VDC-0.A-P < 0 ma < 120 ma < 4 W pnp 0. A 0.3 ms resistive, inductive, lamp load > 48 ò < 1.2 H < 6 W < 100 Hz yes 1 electronics for the field level 8 0 to C 420 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

88 BL20 electronic module 32 digital outputs BL20-32DO-24VDC-0.A-P Compatible base modules Dimensions 14, BL20-B6T-BCBC Tension spring connection, access to C rail BL20-B6-BCBC crew connection, access to C rail F ,8 F234 - Wiring diagram Bit Bit PE PE Bit Bit PE PE Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

89 BL20 electronic module 2 analog outputs BL20-2AO-I(4...20MA) 73,1 LED 74,1 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 analog outputs 0/4 20 ma 117,6 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Load resistance, resistive Load resistance, inductive Electrical isolation Transmission frequency Basic fault limit at 23 C Repeatability Temperature coefficient Resolution Measured-value display Number of parameter bytes Operating temperature BL20-2AO-I(4...20MA) < 0 ma < 40 ma < 1 W 0/4 20 ma < 0.4 kò < 1 mh electronics for the field level < 200 Hz < 0.2 % 0.0 % < 10 ppm/ C of full scale 16 Bit 16 bit signed integer 12 bit full range left justified 6 0 to C 422 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

90 BL20 electronic module 2 analog outputs BL20-2AO-I(4...20MA) Compatible base modules Dimensions 117, BL20-3T-BB Tension spring connection BL20-3-BB crew connection F236 F236 - Wiring diagram h h Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

91 BL20 electronic module 2 analog outputs BL20-2AOH-I 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 analog outputs 0/4 20 ma HART Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Load resistance, resistive Load resistance, inductive Electrical isolation Basic fault limit at 23 C Repeatability Temperature coefficient Resolution Measured-value display Cycle time Number of parameter bytes Operating temperature BL20-2AOH-I < 20 ma < 30 ma < 1 W 0/4 20 ma < 0.60 kò < 1 mh Electronics to field level, channel to channel < 0.2 % 0.0 % < 10 ppm/ C of full scale 16 Bit 16 bit signed integer NE43(PA), Extended 20 ms 12 0 to C 424 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

92 BL20 electronic module 2 analog outputs BL20-2AOH-I Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F286 F286 - Wiring diagram Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 42 /0812

93 BL20 electronic module 2 analog outputs BL20-2AO-U(-10/0...10VDC) 73,1 LED 74,1 Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 analog input -10/0 10 VDC 117,6 14, Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Load resistance, resistive Load resistance, capacitive Electrical isolation Transmission frequency Basic fault limit at 23 C Repeatability Temperature coefficient Resolution Measured-value display Number of parameter bytes Operating temperature BL20-2AO-U(-10/0...10VDC) < 0 ma < 43 ma < 1 W -10/0 10 VDC > 1 kò > 1 µf electronics for the field level < 100 Hz < 0.2 % 0.0 % < 300 ppm/ C of full scale 16 Bit 16 bit signed integer 12 bit signed integer left justified 12 bit full range left justified 6 0 to C 426 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

94 BL20 electronic module 2 analog outputs BL20-2AO-U(-10/0...10VDC) Compatible base modules Dimensions 117, BL20-3T-BB Tension spring connection BL20-3-BB crew connection F236 F236 - Wiring diagram h h Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

95 BL20 Economy Module 4 analog outputs BL20-E-4AO-U/I LED 73,1 72,6 Independent of the type of fieldbus used Electronics and connection technology in an single housing Tension spring connection technology Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 4 analog outputs 0 20 ma, 4 20 ma, VDC or 0 10VDC, electable per channel Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Outputs Output type Load resistance, resistive Load resistance, inductive Load resistance, capacitive Electrical isolation Basic fault limit at 23 C Measured-value display Temperature coefficient Resolution Cycle time Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-E-4AO-U/I < 130 ma < 0 ma < 2.6 W 0 20 ma, 4 20 ma, VDC or 0 10 VDC < 0.4 (current) or > 1 (voltage) kω < 0.01 (voltage) mh < 1 (current) μf electronics for the field level < 0.2 % 16 bit signed integer < 300 ppm/ C of full scale 16 Bit 0 ms to C Terminal connection U 1 h 2 h 3 h 4 h I h h h h /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

96 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax /0812

97 BL20 electronic module R232 interface BL20-1R232 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers Transmission of serial data via R232 interface For connection of different devices, such as printers, scanners or bar code readers Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs / Outputs Transmission level active (U R1) Transmission level inactive (URO) Common-mode range (UGL) Transmission signals Data buffer received end data buffer type Transmission rate Parameter Cable length Electrical isolation Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-1R < 2 ma < 140 ma < 1 W -1 to -3 VDC 3 to 1 VDC -7 to 12 VDC RxD, TxD, RT, CT 128 Byte 64 Byte full duplex 300 to bps transmission rate, diagnostics, data bits, stop bits, XON - character, XOFF - character, parity, flow control 1 m isolation of electronics and field level via optocouplers to C 430 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

98 BL20 electronic module R232 interface BL20-1R232 Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F238 F238 - Wiring diagram RxD TxD GND CT RT HLD Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

99 BL20 electronic module R48/422 interface BL20-1R48/422 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers Transmission of serial data via R48/422 interface For connection of different devices, such as printers, scanners or bar code readers Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs / Outputs Transmission signals Data buffer received end data buffer type Transmission rate Parameter Cable length Line impedance Bus termination Electrical isolation Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-1R48/ < 2 ma < 60 ma < 1 W TxD, RxD 128 Byte 64 Byte 2-wire half duplex or 4-wire full duplex 300 to bps R48/422, transmission rate, diagnostics, data bits, stop bits, XON - character, XOFF - character, parity, flow control 30 m 120 ò external isolation of electronics and field level via optocouplers to C 432 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

100 BL20 electronic module R48/422 interface BL20-1R48/422 Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F239, F240 F239 - wiring diagram for R422 F240 - wiring diagram for R48 TxD/RxD/P TxD 11 GND 12 HLD 13 RxD TxD 21 GND 22 HLD 23 RxD 11 Data In GND 12 HLD Data Out 13 TxD-/RxD-/N 21 GND 22 HLD 23 Data In TxEnable Data Out Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

101 BL20 electronic module connection of I sensors BL20-1I 73,1 LED 74,1 117,6 14, Independent of the type of fieldbus and connection technology used Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers of I sensors Maximum bit transmission rate 1 Mbps Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs / Outputs Transmission signals type Transmission rate Parameter Cable length Electrical isolation Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-1I < 2 ma < 0 ma < 1 W CL, D 4-wire full duplex (clock output/signal input) 62. kbps up to 1 Mbps transmission rate, diagnostics, data format (binary / GRAY coded), data frame bits (1-32), number of invalid bits (LB: 0-1, MB 0-7) 30 m isolation of electronics and field level via optocouplers to C 434 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

102 BL20 electronic module connection of I sensors BL20-1I Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F241 F241 - Wiring diagram CL D Clock CL GND UL D Data 24 Out I Device Parallel-erial-Converter Opto Array Analog Array Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 43 /0812

103 BL20 Economy Module 2 counter/encoder channels, 2 PWM outputs BL20-E-2CNT-2PWM LED 73,1 Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Electrical isolation 72,6 BL20-E-2CNT-2PWM < 20 ma < 0 ma < 1 W isolation of electronics and field level via opto- Low level signal voltage couplers 0 1 VDC / 0 4. VDC 1 High level signal voltage VDC / VDC Low level signal current ma / ma 2 High level signal current ma / 0.6 3mA Counter 1 3 Outputs Filter on > 16 µs (62, khz) Filter off < 2. µs (200 khz) 4 Output type PNP Output voltage Output current per channel Output delay Load type Lamp load witching frequency witching frequency, resistive Inductive switching frequency witching frequency, lamp load hort-circuit protection imultaneity factor Number of diagnostic bytes Number of parameter bytes Operating temperature 0. A 0.2 ms resistive, inductive, lamp load < 10 W Hz < 100 Hz < 2 Hz < 10 Hz yes to C Independent of the type of fieldbus used Electronics and connection technology in an single housing Tension spring connection technology Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers 2 counter/encoder channels 200 khz 2 digital outputs 20kHz / 0.A 2 PWM outputs 20kHz / 0.A Counting mode: Continuous, single or periodic count Measuring mode: Frequency, rotation speed or period duration measurement Terminal connection 6 7 Counter PWM PWM A1 / DI1 (200kHz) B1 / DI2 (200kHz) Z1 / DI3 (10kHz) UB GND A2 / DI4 (200kHz) B2 / DI (200kHz) Z2 / DI6 (10kHz) UB GND P1 (0,A / 20kHz) Direction / DO1 (0,A) GND P2 (0,A / 20kHz) Direction / DO2 (0,A) GND 436 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

104 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax /0812

105 RFID system Interface for connection of BL ident write-read heads (HF/UHF) BL20-2RFID-A 73,1 LED 74,1 117,6 14, This module is used together for example with the gateway BL20-GW-DPV1 Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers of 2 BL ident write-read heads Mixed operation of HF and UHF writeread heads transmission rate: 11.2 kbps Cable length: 0 m maximum Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs / Outputs Transmission rate Cable length Electrical isolation imultaneity factor BL20-2RFID-A < 100 ma < 30 ma < 1 W 11.2 kbps 0 m isolation of electronics and field level via optocouplers 1 ensor supply 0.2 A per channel, short-circuit proof Number of diagnostic bytes Number of parameter bytes Number of input bytes Number of output bytes Operating temperature to C 438 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

106 RFID system Interface for connection of BL ident write-read heads (HF/UHF) BL20-2RFID-A Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F242 F242 - Wiring diagram ( /200) Data 0 (BK) Data 0 (WH) Transceiver GND (BU) (BN) GND (3 BU) (1 BN) Data 1 (2 BK) Data 1 (4 WH) Transceiver Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

107 RFID system Interface for connection of BL ident write-read heads (HF/UHF) BL20-2RFID- 73,1 LED 74,1 117,6 14, No special software (function module) is necessary for integration in the PLC systems 8 byte user data per read / write cycle LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers of 2 BL ident write-read heads Mixed operation of HF and UHF writeread heads Transmission rate: 11.2 kbps Cable length: 0 m maximum Ident-No. Number of channels Rated voltage from the supply terminal Rated current from field supply Rated current from module bus Power loss, typical Inputs / Outputs Transmission rate Cable length Electrical isolation imultaneity factor BL20-2RFID < 100 ma < 30 ma < 1 W 11.2 kbps 0 m isolation of electronics and field level via optocouplers 1 ensor supply 0.2 A per channel, short-circuit proof Number of diagnostic bytes Number of parameter bytes Number of input bytes Number of output bytes Operating temperature to C 440 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

108 RFID system Interface for connection of BL ident write-read heads (HF/UHF) BL20-2RFID- Compatible base modules Dimensions BL20-4T-BB Tension spring connection BL20-4-BB crew connection F242 F242 - Wiring diagram ( /200) Data 0 (BK) Data 0 (WH) Transceiver GND (BU) (BN) GND (3 BU) (1 BN) Data 1 (2 BK) Data 1 (4 WH) Transceiver Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

109 BL20 Economy Module WIRE communication module BL20-E-1WIRE LED 73,1 72,6 Independent of the type of fieldbus used Electronics and connection technology in an single housing Tension spring connection technology Degree of protection IP20 LEDs for display of status and diagnostics Electronics galvanically isolated from the field level via opto-couplers upports the connection of a WIRE branch. Maximum 16 nodes per WIRE branch Maximum 3 WIRE modules per BL20 station Ident-No. Number of channels Admissible range Voltage supply for contactor Voltage supply for contactor Rated current from module bus Electrical isolation Number of diagnostic bytes Number of parameter bytes Operating temperature BL20-E-1WIRE WIRE branch VDC 3 A < 60 ma isolation of electronics and field level via optocouplers to C Terminal connection U AUX U W 442 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

110 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax /0812

111 BL20 motor starter ave switching and protection of motors Direct and reversing starters up to 1 kw The motor starters consequently build upon the advantages of the BL20 system: Modular Flexible imple mounting and operation Cost-efficient BL20 direct and reversing motor starters fulfil the requirements of the IEC/EN norm for industrial switching devices. Modular mounting A BL20 motor starter is composed of standard components. Easy and error-free mounting of direct or reversing starters with a power range between 0.06 kw and 1 kw is thus possible. This applies to the single components of which a motor starter is built, as well as to the connection between motor starters and the gateway. hould it become necessary to adapt the motor starter to altered conditions, the relevant components can be easily exchanged. 444 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

112 Compact system solution The WIRE connection module allows a maximum of 4 m between the module and the last motor starter. This allows an exceptionally flexible layout of the motor starters in the control cabinet and thus compact solutions. WIRE connection Communication Due to digital communications between the motor starters and the BL20, various diagnostics are available to the host system. This is realised without the need for extra I/Os. This means: Reduction of commissioning times Quick trouble shooting Lower costs Configuration The integration of motor starters in the BL20 system is very easy: All connected motor starters are configured in the BL20 system by a simple tap on a pushbutton. maximum distance 4 m Maximum system expansion Up to 16 motor starters per WIRE module, up to 3 WIRE branches per BL20-system = up to 48 motor starters per fieldbus interface! Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 44 /0812

113 BL20 motor starter election guide direct starter = Rated operating performance AC-3, 380 V 41 V Motor protection switch Auxiliary switch for motor protection switch WIRE communication module P, kw / hp pcs / package pcs /package 0.06 / 0.08 PKZM0-0, / 0.12 PKZM0-0, / 0.16 PKZM0-0, / 0.24 PKZM0-0, / 0.33 PKZM / 0. PKZM0-1, / 0.74 PKZM0-1, / 1 PKZM0-2, / 1. PKZM / 2 PKZM / 2.9 PKZM0-6, / 4 PKZM /.4 PKZM / 7.38 PKZM / 10 PKZM / 10 PKZM / 1 PKZM / 20 PKZM NHI-E-10L-PKZ0 (pcs) BL20-WIRE-DIL(pcs) * These power contactors require a different wiring set as mentioned here 446 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

114 1 coordination In type 1 coordination, the contactor or soft starter must not endanger persons or the installation in the event of a short-circuit and does not have to be capable of continued use without repairs or parts replacements. 2 coordination In type 2 coordination, the contactor or soft starter must not endanger persons or the installation in the event of a short-circuit and must be capable of continued use without repairs or parts replacements. or Power contactor Wiring set Power contactor Wiring set Aux. contact Aux. contact 1 N. C. 1 N. O. 1 N. C. 1 N.O. DILM7-01(24VDC) DILM7-10(24VDC) DILM7-01(24VDC) DILM7-10(24VDC) BL20-PKZM0-XDM BL20-PKZM0-XDM DILM9-01(24VDC) DILM9-10(24VDC) DILM12-01(24VDC) DILM12-10(24VDC) DILM17-01(RDC24)* DILM17-10(RDC24)* DILM1-01(24VDC) DILM1-10(24VDC) BL20-PKZM0-XDM DILM17-01(RDC24)* DILM17-10(RDC24)* DILM2-01(RDC24)* DILM2-10(RDC24)* BL20-PKZM0-XDM DILM2-01(RDC24)* DILM2-10(RDC24)* DILM32-01(RDC24)* DILM32-10(RDC24)* DILM32-01(RDC24)* DILM32-10(RDC24)* Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

115 BL20 motor starter election guide reversing starter = 2 Rated operating performance AC-3, 380 V 41 V Motor protection switch Auxiliary switch for motor protection switch WIRE communication module P, kw / hp pcs / package pcs / package 0.06 / 0.08 PKZM0-0, / 0.12 PKZM0-0, / 0.16 PKZM0-0, / 0.24 PKZM0-0, / 0.33 PKZM / 0. PKZM0-1, , / 0,74 PKZM0-1, / 1 PKZM0-2, / 1. PKZM / 2 PKZM / 2.9 PKZM0-6, / 4 PKZM /.4 PKZM / 7.38 PKZM NHI-E-10L-PKZ0 (pcs) BL20-WIRE-DIL(pcs) / 10 PKZM / 10 PKZM / 1 PKZM / 20 PKZM * These power contactors require a different wiring set as mentioned here 448 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

116 1 coordination In type 1 coordination, the contactor or soft starter must not endanger persons or the installation in the event of a short-circuit and does not have to be capable of continued use without repairs or parts replacements. 2 coordination In type 2 coordination, the contactor or soft starter must not endanger persons or the installation in the event of a short-circuit and must be capable of continued use without repairs or parts replacements. or 2 2 Power contactor Wiring set Mech. interlock Aux. contact Power contactor Wiring set Mech. interlock Aux. contact 1 N. C. 1 N. O. 1 N. C. 1 N. O. DILM7-01(24VDC) DILM7-10(24VDC) DILM7-01(24VDC) DILM7-10(24VDC) BL20-PKZM0- XRM DILM12- XMV BL20-PKZM0- XRM DILM12- XMV DILM9-01(24VDC) DILM12-01(24VDC) DILM17-01(RDC24)* DILM9-10(24VDC) DILM12-10(24VDC) DILM17-10(RDC24)* DILM17-01(RDC24)* DILM17-10(RDC24)* BL20-PKZM0- XRM DILM32- XMV DILM2-01(RDC24)* DILM2-10(RDC24)* BL20-PKZM0- XRM DILM32- XMV DILM2-01(RDC24)* DILM2-10(RDC24)* DILM32-01(RDC24)* DILM32-10(RDC24)* DILM32-01(RDC24)* DILM32-10(RDC24)* Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com /0812

117 BL20 motor starter Technical specification motor protection switch Ident-no. Max. rated operating performance Rated continuous current AC3 220 V 380 V 440 V 00 V 660 V 230 V 400V 690 V 240 V 41 V etting range overload release hort circuit release P [kw] I u [A] I r [A] I m [A] PKZM0-0, PKZM0-0, PKZM0-0, PKZM PKZM0-1, PKZM0-2, PKZM PKZM0-6, PKZM PKZM PKZM PKZM PKZM Tripping characteristic for motor protection switch PKZM0-2h min s ms , x operating rated current 40 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com

118 BL20 motor starter Technical specification power contactor Ident-no. Rated operating current Max. rated operating performance three-phase AC motor 0 60 Hz I th = I e, AC-1 at 60 C, open Contactcomplement AC-3 AC-3 AC V 220 V 380 V 660 V 220 V 380 V 660 V 400 V 230 V 400 V 690 V 230 V 400 V 690 V I e [A] P [kw] P [kw] I th = I e [A] N. O./ N. C. DILM7-01(24VDC) N. C. DILM7-10(24VDC) N. O. DILM9-01(24VDC) N. C. DILM9-10(24VDC) N. O. DILM12-01(24VDC) N. C. DILM12-10(24VDC) N. O. DILM1-01(24VDC) N. C. DILM1-10(24VDC) N. O. DILM17-01(RDC24) N. C. DILM17-10(RDC24) N. O. DILM2-01(RDC24) N. C. DILM2-10(RDC24) N. O. DILM32-01(RDC24) N. C. DILM32-10(RDC24) N. O. Electrical interlock wiring for reversing starters NHI-E-10L-PKZ0 X1 X2 X1 X2 BL20-WIRE-DIL BL20-WIRE-DIL X3 X4 X3 X4 DILM..-01 DILM Power contactors with a N. C. output are obligatory for the electrical interlock of reversing starters. The wiring is implemented by the user as shown on the left. All other necessary connections are implemented with pluggable bridges which are included in the wiring sets. Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com 41 /0812

119 BL20 motor starter Accessories Figure Description Ident-no. Three-phase current rail, insulated, U e = 690 V, I u = 63 A, extension enabled by rotated mounting, length 90 mm B3.0/2-PKZ Three-phase current rail, insulated, U e = 690 V, I u = 63 A, extension enabled by rotated mounting, length 180 mm B3.0/4-PKZ Input terminal for three-phase current rail, insulated, U e = 690 V, I u = 63 A, BK2/3-PKZ No-load connection cover for non-assigned connections at three-phase current rails 20 pcs/ package H-B3-PKZ0(20pcs) WIRE power module. For power supply of WIRE branches. Is applied when groups of motor starters have to be disconnected. Max. 4 Power modules per WIRE branch. BL20-WIRE-PF Terminating connector for WIRE-branches, no electrical function 2 pcs / package BL20-WIRE-CAB-000 (2pcs) WIRE connection cable, length 8 mm 2 pcs / package WIRE connection cable, length 110 mm 2 pcs / package WIRE connection cable, length 10 mm pcs / package WIRE connection cable, length 20 mm pcs / package BL20-WIRE-CAB-008 (2pcs) BL20-WIRE-CAB-011 (2pcs) BL20-WIRE-CAB-01 (pcs) BL20-WIRE-CAB-02 (pcs) WIRE connection cable, length 00 mm BL20-WIRE-CAB WIRE connection cable, length1000 mm BL20-WIRE-CAB WIRE connection cable, length 2000 mm BL20-WIRE-CAB Mechanical interlock for reversing starters with power contactors DILM7-DILM1 DILM12-XMV Mechanical interlock for reversing starters with power contactors DILM17-DILM32 DILM32-XMV User manuals The user manual for BL20 systems is only available as PDF file and can be downloaded on 42 /0812 Hans Turck GmbH & Co. KG 4472 Mülheim/Ruhr Germany Tel Fax more@turck.com