BL20 UNIVERSAL I/O BUS TERMINAL SYSTEM

Transcription

1 BL20 UNIVERSAL I/O BUS TERMINAL SYSTEM F 418/02

2 2 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

3 The BL20 concept 6 BL20 and fieldbus protocols BL20 and PROFIBUS-DP 8 BL20 and CANopen 10 BL20 and DeviceNet TM 12 BL20 system extension and system supply 14 General technical information Formula symbols, ID colors 16 Module identification legend 17 Dimensions 18 General technical data of BL20 modules 20 Technical data Gateways 21 Power distribution modules 28 Digital input modules 32 Analog input modules 40 Digital output modules 48 Analog output modules 54 Relay modules 56 Counter module 60 BL20 module guide 64 Software I/Oassistant 66 busstop monitor 67 Accessories guide 68 BL20 product range 70 Type reference list 73 Contact 80 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 3

4 The BL20 concept The modular concept of BL20: gateway, block and slice design, is a combination of many benefits which, as one, represent a completely new approach to quality in the I/O field. The BL20 gateway means that I/O modules are no longer dependent on the type of fieldbus. Its function is to provide communication between the fieldbus and the I/O modules. The DIN-rail mountable base modules, available in block or slice design, represent the connection level for the field devices. The electronics modules, also available as block or slice, are pluggable, and contain the channel functions. The power distribution module (24 V DC or 120/230 V AC) supplies the interconnected I/O with the required voltage. Bus-independence, precise project planning (you only purchase the required number of channels), the high-level of compactness, the list is endless. In short: openness and flexibility are BL20's strengths. Electronic module in block design Electronic module in slice design Gateway Gateway Interface between BL20 periphery modules and the fieldbus Supports the fieldbus protocols PROFIBUS-DP, Device Net TM, CANopen Coordinates the entire process data exchange Generates diagnostic information for the higher-level controller Fieldbus connection via direct wiring or fieldbus-specific plugs Offers integrated interfaces for the software I/Oassistant Enables the setting of fieldbus addresses 4 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

5 End plate Together with the integrated end bracket, it is the mechanical termination of each BL20 station. Together with an end bracket mounted next to the gateway it guarantees the vibration resistance of the station. The end plate comes with the gateway. End plate Base module in slice design Electronic modules Contain a large number of I/O functions Communicate with the gateway via an internal module bus Are independent of the higher-level fieldbus Are pluggable and independent of the field wiring Are available in slice design with 1, 2 or 4 channels or in block design with 16 or 32 channels Offer type-specific color identification Base module in block design Base modules Are the connection for the field wiring Are based on terminal block technology Are available in slice and block design with tension clamp or screw connections Are available in 2-/3-, 4- and 4x2-/3- wire connection technology Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 5

6 BL20 detailed concept Software I/Oassistant (optional) Windows based Project planning Configuration Parameterization Monitoring BL20 Openness The gateway product palette serves the proven fieldbus systems PROFIBUS- DP, CANopen, DeviceNet The I/O modules do not rely on a particular bus system Bus Refreshing module 6 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

7 Mechanical coding Enables group assignment between electronics and base modules Prevents replacement with wrong modules Relay modules Direct power supply when used in combination with certain base modules (e.g. BL20-S4T-SBCS) Bridging of relay roots and reduction of wiring costs with jumpers (QVR) Power Feeding module Power Feeding modules Field power supply of 24 VDC or 120/230 VAC to BL20 modules Creation of potential groups Bus Refreshing modules Diagnostic function: monitoring of the field voltage System power supply to the BL20 modules and the gateway via the internal module bus. Field power supply of 24 VDC to the modules Creation of potential groups Diagnostic functions: monitoring of the field voltage, module bus supply and module bus overload Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 7

8 BL20 and PROFIBUS-DP Decentralized periphery Optimized for high speed, this PROFIBUS version is designed especially for communication between automation control systems and decentralized periphery devices. PROFIBUS-DP can be used to replace cost-intensive, parallel signal transmission from digital and analogue sensors and actuators. PROFIBUS-DP is based on DIN Part 1 and Part 4. During the course of the European fieldbus standardization, PROFIBUS-DP has been included in the European fieldbus standard EN Maximum system extension without repeaters A PROFIBUS-DP bus line consists of at least a master and a slave. Without a repeater, a PROFIBUS-DP bus line can consist of up to 31 slaves.the maximum number of 32 bus stations must not be exceeded without the use of a repeater! Maximum system extension with repeaters A maximum of 3 repeaters can be used within a PROFIBUS-DP structure. This increases the number of possible slaves to 122. The maximum number of 125 bus stations, including all slaves and repeaters, must not be exceeded! The PROFIBUS-DP addresses 000, 126 and 127 are reserved and must not be used for BL20! Topology PROFIBUS-DP communicates via a shielded twisted pair cable according to the RS 485 standard. The network topology represents a linear structure with active bus termination on both ends Maximum bus length The maximum bus length for PROFIBUS-DP depends on the transmission rate: Cable type Baud rate Max. distance between two stations/cable type A (kbit/s) (DIN Part 3) max. length of a bus line without repeater (m) max. bus length with 3 repeaters (m) Parameters Characteristic impedance Distributed capacitance Loop resistance Wire diameter Wire cross-section Terminating resistor Cable type A DIN Part to 165Ω (3 to 20 MHz) < 30 nf/km < 110 Ω/km > 0.64 mm > 0.34 mm Ω 8 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

9 PROFIBUS-DP system extension BL20 station Maximum system extension BL20 station A BL20 station can consist of a gateway for PROFIBUS-DP and a maximum of 74 slice modules (approximately 1 m length of rail including end bracket and end plate). With the use of block modules, the maximum number of modules is correspondingly reduced (1 block module corresponds to approximately 8 slice modules). Maximum station extension, process data dependent Module types Digital inputs, 4 DI Digital outputs, 2 DO Analog inputs, 1 AI-I Analog inputs, 1 AI-U Analog inputs, 2 AI-PT/Ni Analog inputs, 2 AI-THERMO Analog outputs, 1 AO-I Analog outputs, 2 AO-U Counter module, 1 CNT Channels Max. number/ station / 7 Modules Max. number/ station 72 * 1) 72 * 1) 57 * 1) 57 * 1) 23 ** 1) 38 * 1) 33 * 2) 19 ** 2) 7 ** 1) Ensure that a sufficient number of Power Feeding or Bus Refreshing modules are used if the system is extended to its maximum. If the system limits are exceeded, the software I/Oassistant generates an error message when the user activates the command <Station - Verify>. Maximum station extension, diagnostic data dependent Module types Digital inputs, 4 DI Digital outputs, 2 DO Analog inputs, 1 AI-I Analog inputs, 1 AI-U Analog inputs, 2 AI-PT/Ni Analog inputs, 2 AI-THERMO Analog outputs, 1 AO-I Analog outputs, 2 AO-U Counter module, 1 CNT Channels Max. number/ station / 7 Modules Max. number/ station 72 * 1) 61 * 1) 57 * 1) 57 * 1) 23 ** 1) 29 * 1) 33 * 2) 19 ** 2) 7 ** 1) *...plus 2 Bus Refreshing modules **...plus 1 Bus Refreshing module 1)...Standard GSD file; module description, not compressed 2)...Extended GSD file; module description, not compressed Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 9

10 BL20 and CANopen Bus system CANopen CANopen is a network that is based on the serial, two-wire transfer of Controller Area Networks (CAN). CANopen uses the international CAN standard ISO as the basis for communications with an open network. This standard covers layers 1 and 2 (physical and data link layer) of the ISO/OSI communication model. Building on this, the CANopen family of profiles were developed by the international user and manufacture organization CiA (CAN in Automation). This family of profiles comprises, the communication profile CiA DS 301, which represents ISO/OSI layer 7 (Application Layer) and specifies the communication mechanisms. Plus a number of device profiles (CiA DS 40x) which specify the device functionality. Topology CANopen is based on a linear topology utilizing shielded, twisted-pair cabling with bus terminators at both ends of the bus line in accordance with ISO-DIS Parameters Impedance Resistivety Conduction delay Terminating resistance ISO-DIS to 132 Ω 70 m Ω/m 5 ns/m 120 Ω Mixed operation with other devices Within a CANopen structure, BL20 can be used in conjunction with CANopen conform field bus devices from various manufacturers. Maximum bus length The maximum bus length for CANopen is dependent on the rate of transmission: Baud rate (kbit/s) Max. wire length (m) Maximum system extension A CANopen bus line consists of at least two stations. These could be a PC or PLC, and a BL20 gateway, for example. A bus line can consist of a maximum of 110 stations (for example, BL20 gateways). The use of repeaters can become necessary with bus lengths of more than m. The CANopen Address 000 is reserved for telegrams to all stations and must not be used as a station address! 10 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

11 CANopen system extension BL20 station Maximum system extension BL20 station A BL20 station can consist of a gateway for CANopen and a maximum of 74 slice modules (approximately 1 m length of rail including end bracket and end plate). With the use of block modules, the maximum number of modules is correspondingly reduced (1 block module corresponds to approximately 8 slice modules). Module types Digital inputs, 4 DI Digital outputs, 2 DO Analog inputs, 1 AI-I Analog inputs, 1 AI-U Analog inputs, 2 AI-PT/Ni or 2 AI-THERMO Analog outputs, 1 AO-I Analog outputs, 2 AO-U Counter module, 1 CNT Channels Max. number/ station / 71 Modules Max. number/ station 72 * 72 * 71 ** 71 ** 71 ** 71 ** 71 ** 71 ** Ensure that a sufficient number of Power Feeding or Bus Refreshing modules are used if the system is extended to its maximum. If the system limits are exceeded, the software I/Oassistant generates an error message when the user activates the command <Station - Verify>. *... plus 2 Bus Refreshing modules **... plus 3 Bus Refreshing modules Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 11

12 BL20 and DeviceNet TM Bus system DeviceNet TM The open low-end network DeviceNet TM, is based on CAN technology. The communication profile used by BL20 contains: UCMM Topology DeviceNet TM uses a full trunk / branch line topology with up to 64 nodes. Offline Connection Set Polled I/O COS/Cyclic Bitstrobe Device Heartbeat Message Device Shut Down Message The user can select a master/slave, multimaster or a combined configuration, depending on the application requirements. Maximum bus length The DeviceNet TM specifications permit the use of two types of cable: thick and thin. Depending on the type of cable used, the following maximum bus lengths for the three possible transfer rates are possible. Baud rate (kbit/s) Max. distance between 2 stations 100 % thick cable 100 % thin cable m (1640 ft) 250 m (820 ft) 100 m (328 ft) 100 m (328 ft) 100 m (328 ft) 100 m (328 ft) Maximum system extension The branches can be up to 6 m (20 ft) long, but the total extent of all branches depends on the baud rate. A DeviceNet TM bus line consists of a scanner and at least another bus station. The maximum number of 64 bus stations (including the scanner) must not be exceeded. Mixed operation with other devices Within a DeviceNet TM structure, BL20 can be used in conjunction with standardized DeviceNet TM fieldbus devices from various manufacturers. 12 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

13 DeviceNet TM system extension - BL20 station Maximum system extension BL20 station A BL20 station can consist of a gateway for DeviceNet TM and a maximum of 74 slice modules (approximately 1 m length of rail including end bracket and end plate). With the use of block modules, the maximum number of modules is correspondingly reduced (1 block module corresponds to approximately 8 slice modules). Module types Digital inputs, 4 DI Digital outputs, 2 DO Analog inputs, 1 AI-I Analog inputs, 1 AI-U Analog inputs, 2 AI-PT/Ni or 2 AI-THERMO Analog outputs, 1 AO-I Analog outputs, 2 AO-U Counter module, 1 CNT Channels Max. number/ station /31 Modules Max. number/ station 72 ** 72 ** 71 *** 71 *** 63 *** 71 *** 63 *** 31* Ensure that a sufficient number of Power Feeding or Bus Refreshing modules are used if the system is extended to its maximum. If the system limits are exceeded, the software I/Oassistant generates an error message when the user activates the command <Station - Verify>. *... plus 1 Bus Refreshing modules **...plus 2 Bus Refreshing modules ***...plus 3 Bus Refreshing modules Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 13

14 BL20 system extension General system supply The power supply to a BL20 station is fed via Power Feeding or Bus Refreshing modules, the latter also being responsible for the power supply to the internal module bus. Bus Refreshing modules are used within a BL20 station (without gateway supply) if the system supply to the BL20 modules (nominal current I MB 1.5 A) is no longer sufficiently guaranteed. These Bus Refreshing modules are to be combined with the base modules BL20- P3T-SBB-B or BL20-P4T-SBBC-B (tension clamp connections) or with the base modules BL20-P3S-SBB-B or BL20-P4S- SBBC-B (screw connections). Power Feeding modules are used if the system supply to the BL20 modules (nominal current I EL 10 A) is no longer sufficiently guaranteed. Nominal current consumption The following table offers an overview of the nominal current consumption of the different BL20 types on the module bus: Modules Gateway PROFIBUS-DP Gateway CANopen Gateway DeviceNet BL20-BR-24VDC-D BL20-PF-24VDC-D BL20-PF-120/230VAC-D BL20-2DI-24VDC-P BL20-2DI-24VDC-N BL20-2DI-120/230VAC-P BL20-4DI-24VDC-P BL20-4DI-24VDC-N BL20-16DI-24VDC-P BL20-32DI-24VDC-P BL20-1AI-I(0/4..20mA) BL20-2AI-I(0/4...20mA) BL20-1AI-U(-10/0..+10VDC) BL20-2AI-U(-10/0..+10VDC) BL20-2DO-24VDC-0.5A-P BL20-2DO-24VDC-0.5A-N BL20-2DO-24VDC-2A-P BL20-4DO-24VDC-0.5A-P BL20-16DO-24VDC-0.5A-P BL20-1AO-I(0/4...20mA) BL20-2AO-I(0/4...20mA) BL20-2A0-U(-10/ VDC) BL20-2DO-R-NC BL20-2DO-R-NO BL20-2DO-R-CO BL20-1CNT Power supply I MB 1500 ma System supply BL20 gateway The first module on a BL20 station after the BL20 gateway must always be a Bus Refreshing module as well as the corresponding base module BL20-P3x-SBB or BL20-P4x-SBBC with tension clamp or screw connection to supply the gateway. Nominal current I MB 430 ma 350 ma 250 ma 28 ma 25 ma 28 ma 28 ma 28 ma 29 ma 28 ma 45 ma 30 ma 41 ma 35 ma 41 ma 35 ma 32 ma 32 ma 33 ma 30 ma 45 ma 39 ma 43 ma 43 ma 28 ma 28 ma 28 ma < 40 ma System supply via module bus The number of BL20 modules that can be supplied by a Bus Refreshing module via the internal module bus depends on the respective nominal current I MB of the individual modules on the module bus. The sum total of the nominal current inputs of the connected BL20 modules must not exceed 1.5 A. The power requirements of the BL20 gateway supplied via the first Bus Refreshing module in the station is to be is to be taken into consideration when calculating the required number of Bus Refreshing modules. If the software I/Oassistant is used, an error message is generated automatically via the <Station - Verify> as soon as the system supply via the module bus in no longer sufficiently guaranteed. All Bus Refreshing modules used in a BL20 station are to be connected via the same frame potential. The power supply to the module bus is fed via the connections 11 (plus) and 21 (ground) of the respective base module for the Bus Refreshing module. Creating potential groups Both Bus Refreshing modules as well as Power Feeding modules can be used to create a potential group. The potential isolation of the potential group on the left-hand side of the respective power distribution module is created by the base module. It is not permitted for modules with 24 VDC and with 120/230 VAC field supply to be used in a joint potential group. Therefore, it must be observed that when using digital input modules for 120/230 VAC the Power Feeding module BL20-PF- 120/230VAC-D is to be used to create a special potential group. 14 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

15 BL20 system supply C-rail (cross connection) The C-rails run through all I/O base modules. The C-rail of the base modules for power distribution modules is mechanically separated; thus potentially isolating the adjoining supply groups. Access to the C-rail Access to the C-rail is made via base modules with a C in their designation (for example, BL20-S4T-SBCS). The corresponding connection level is indicated by a thick black line on all base modules for BL20 I/O modules. With base modules for power distribution modules, the black line is above the connection 24 only. This makes clear that the C-rail is separated from the adjoining potential group to its left. It is permitted to load the C-rail with a maximum of 24 V! Never with 120/230 VAC. The C-rail can be used as required in the application, for example, as a protective earth (PE). In this case, the PE connection of each power distribution module must be connected to the mounting rail via an additional PE terminal, which is available as an accessory. Using the C-rail with relay modules The C-rail can be used to supply a common voltage when relay modules are to be used. To accomplish this, the load voltage (24 VDC) is connected to a power distribution module with the base module BL20-P4x- SBBC with either tension clamp or screw connection. All the following relay modules are supplied with 24 VDC via the C-rail (1). The cross-connection of the individual relay modules is achieved using the crossconnector QVR (2). If the C-rail is to be used for the joint supply of voltage to relay modules, then there must subsequently be a further power distribution module used for the potential isolation of the following BL20 modules. The C-rail can again be put on other uses (for example, as a PE) once the potential isolation has been made. Using the C-rail as a protective earth The C-rail can be used as required in the application, for example, as a protective earth (PE). In this case, the PE connection of each power distribution module must be connected to the mounting rail via an additional PE terminal, which is available as an accessory. Gateway BR 2 DO 2 DI 2 DO 2 DI PF 2 DO 2 DI 2 DO 2 DI PE terminal SHLD DGND VP A B TS SHLD DGND VP A B XI/ON Your fieldbus connection C-rail (PE) C-rail (PE) 24 SBBC SBC SBBC SBC SBB SBBC SBC SBBC SBC SBB Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 15

16 Formula symbols / ID colours for BL20 electronics modules Abbreviation GND I A I El I H I I I L I MB L- L+ PE R LI R LK R LL R LO S Sh U A U H U I U h U L U L U PF U sys Designation Ground Active level current (with negative switching electronics modules) Electrical operating supply (field voltage) High-level current Inactive level current (with negative switching electronics modules) Low-level current Current via the module bus Neutral conductor Positive conductor Protective earth conductor Load impedance, inductive Load impedance, capacitive Lamp load Resistive load Signal cable Shielding Active level voltage (with negative switching electronics modules) High-level voltage Inactive level voltage (with negative switching electronics modules) Auxiliary voltage for analogue valuator sensor Field supply with LEDs Low-level voltage Voltage that is presently being supplied via the power distribution module System supply Electronic modules Gateway ID colour dusty grey Bus Refreshing modules 24 VDC Power Feeding modules 24 VDC Power Feeding modules 120/230 VAC Digital input modules Analogue input modules Digital output modules Analogue output modules Relay modules Technology modules (counter module) dusty grey dusty grey orange brown light grey pigeon blue strawberry red pale green pastel orange zinc yellow 16 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

17 Module type code ID ABPL AI AO B B B BR C CJ CNT CO D DI DO GW KLBU KO MB N NC NI NO P P PBDP PF PI PT QV R S S S S T x Designation End plate for right-sided termination of a BL20 station Analogue input module Analogue output module Designation for base module in block design Bridge connector: bridged connections on the same connection level in a base module, for applying potentials Added to designation of base modules for those Bus Refreshing modules used within a BL20 station but do not supply the gateway with power. Bus Refreshing module Designation of a connection level with cross-connection to a C-rail and can, among other things, be used as a PE (only possible with certain base modules). Base module for BL20-2AI-THERMO-PI with integrated PT100 for cold junction compensation Counter Changeover Diagnostics Digital input module Digital output module Gateway Terminal clip, shield connection for analogue input modules Coding element for coding electronics and base modules MBaud (MBit/s); transmission rate for data transfer Negative switching Normally closed for connecting resistance thermometers with sensors Ni100 and Ni1000 in 2- or 3-wire measurement type Normally open Positive switching Designation of the base module for Power Feeding and Bus Refreshing modules BL20-Gateway for PROFIBUS-DP Power Feeding modules Analogue input module for connecting thermoelements with cold junction compensation Analogue input module for connecting resistance thermometers with sensors PT100, PT500 and PT1000 in 2- or 3-wire measurement type Jumper for relay modules Relay module Designation for base module in slice design Designation for base modules with screw connection Designation for gateway with screw connection Single connector: non-bridged connections on the same connection level in a base module, used for connecting the signal Designation for base modules with tension clamp connection Partly for S or T in the designations of base modules with screw or tension clamp connections Examples XN-ABPL BL20-1AI-U (-10/ VDC) BL20-1AO-I(0/4...20MA) BL20-B3S-SBB BL20-S3T-SBB BL20-P4T-SBBC-B BL20-BR-24VDC-D BL20-S4T-SBBC BL20-S4T-SBBS-CJ BL20-1CNT-24VDC BL20-2DO-R-CO BL20-BR-24VDC-D BL20-2DI-24VDC-P BL20-2DO-24VDC-2A-P BL20-GW-PBDP-1.5MB XN-KLBU/T XN-KO/2 BL20-GW-PBDP-1.5MB BL20-2DI-24VDC-N BL20-2DO-R-NC BL20-2AI-PT/NI-2/3 BL20-2DO-R-NO BL20-2DI-24VDC-P BL20-P3T-SBB BL20-GW-PBDP-1.5MB BL20-PF-24VDC-D BL20-2AI-THERMO-PI BL20-2AI-PT/NI-2/3 XN-QV/1 BL20-2DO-R-NC BL20-S3T-SBB BL20-S3S-SBB BL20-GW-PBDP-1.5MB-S BL20-S3T-SBB BL20-S3T-SBB BL20-S3x-SBB Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 17

18 Dimensions Electronic modules in slice design in block design Base modules in slice design 2-/3-wire connection technology 4-wire connection technology 4 x 2-/3-wire connection technology in block design 2-/3-wire connection technology 4-wire connection technology 4 x 2-/3-wire connection technology Dimensions in mm (W x L x H) 12.6 x 74.1 x x 74.1 x x x x x x x x x x x x x 49.9 Complete BL20 module (slice design; base module with tension clamp connection Electronic module in slice design Electronic module in block design 18 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

19 Base module with tension clamp connection (side view) Base module with screw connection (side view) Base module in slice design (top view) Base module in block design (top view) Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 19

20 General technical data BL20 General technical data BL20 generell Potential isolation Ambient temperature Operating temperature Storage temperature Relative humidity Noxious gas SO 2 H 2 S Resistant to vibration Operating conditions Resistant to shock Resistant to repetitive shock Topple and fall Protection class Electromagnetic compatibility (EMC) Tests Base modules Measurement data Connection technology in TOP construction Insulation stripping length Crimpable wire Nominal diameter "e" solid core H 07V-U "f" flexible core H 07V-K "f" with ferrules according to DIN /1 (ferrules crimped gas-tight) Plug gauge according to IEC 947-1/1988 Protection class Approvals via optocoupler 32 F to +131 F (0 to +55 C) -13 F to +185 F (-25 to +85 C) 5 to 95 % (indoor), Level RH-2, without condensation (storage at 45 C) 10 ppm (rel. humidity < 75 %, without condensation) 1.0 ppm (rel. humidity < 75 %, without condensation) according to EN according to EN according to IEC according to IEC according to IEC and free fall according to IEC IP 20 according to EN (Industry) according to EN according to VDE 0611 part 1/8.92 / IEC /1989 tension clamp or screw connection 8 mm 1.5 mm to 2.5 mm to 1.5 mm to 1.5 mm 2 A1 IP 20 CE UL CSA 20 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

21 Technical data Gateways Gateway PROFIBUS DP Gateway overview: The gateway is the interface between the BL20 periphery modules and PROFIBUS-DP It is responsible for the data exchange between the BL20 station and the PROFIBUS-DP master The connection to the PROFIBUS-DP is made via 9-pole SUB-D socket or by direct wiring Hexadecimal rotary switches for setting the PROFIBUS-DP station address ( ) LEDs for indicating supply voltage, group or bus errors BL20 Gateway PROFIBUS BL20-GW-PBDP-1.5MB (tension clamp) Supply voltage Permissible range Residual ripple Nominal current consumption from module bus I MB Service interface Connection technology fieldbus Connection technology for direct wiring Transmission speed Fieldbus addressing Fieldbus termination Passive LWL adapters can be connected Number of parameter bytes Number of diagnostic bytes Address range for PROFIBUS-DP Included in range of supply 5 V DC (from Bus Refreshing module) 4.7 to 5.3 VDC according to EN ma PS/2 socket 2x SUB-D sockets, 9-pole 2x direct wiring, 5-pole tension clamp 9.6 kbit/s to 1.5 MBit/s 2 hexadecimal rotary switches via SUB-D connector current consumption max. 100 ma 5 Bytes 3 Bytes 001 to 125 dec x x 74.4 mm 2x end bracket XN-WEW-35/2-SW 1x end plate XN-ABPL Ordering information Type BL20-GW-PBDP-1.5MB Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 21

22 Technical data Gateways Gateway PROFIBUS DP Gateway overview: The gateway is the interface between the BL20 periphery modules and PROFIBUS-DP It is responsible for the data exchange between the BL20 station and the PROFIBUS-DP master The connection to the PROFIBUS-DP is made via 9-pole SUB-D socket or by direct wiring Hexadecimal rotary switches for setting the PROFIBUS-DP station address ( ) LEDs for indicating supply voltage, group or bus errors BL20 Gateway PROFIBUS BL20-GW-PBDP-1.5MB-S (screw connection) Supply voltage Permissible range Residual ripple Nominal current consumption from module bus I MB Service interface Connection technology fieldbus Connection technology for direct wiring Transmission speed Fieldbus addressing Fieldbus termination Passive LWL adapters can be connected Number of parameter bytes Number of diagnostic bytes Address range for PROFIBUS-DP Included in range of supply 5 V DC (from Bus Refreshing module) 4.7 to 5.3 VDC according to EN ma PS/2 socket 2x SUB-D sockets, 9-pole 2x direct wiring, 5-pole screw connection 9.6 kbit/s to 1.5 MBit/s 2 hexadecimal rotary switches via SUB-D connector current consumption max. 100 ma 5 Bytes 3 Bytes 001 to 125 dec x x 74.4 mm 2x end bracket XN-WEW-35/2-SW 1x end plate XN-ABPL Ordering information Type BL20-GW-PBDP-1.5MB-S Ident-number /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

23 Technical data Gateways Gateway PROFIBUS DP Gateway overview: The gateway is the interface between the BL20 periphery modules and PROFIBUS-DP It is responsible for the data exchange between the BL20 station and the PROFIBUS-DP master The connection to the PROFIBUS-DP is made via 9-pole SUB-D socket or by direct wiring Hexadecimal rotary switches for setting the PROFIBUS-DP station address ( ) LEDs for indicating supply voltage, group or bus errors BL20 Gateway PROFIBUS BL20-GW-PBDP-12MB Supply voltage Permissible range Residual ripple Nominal current consumption from module bus I MB Service interface Connection technology fieldbus Transmission speed Fieldbus addressing Fieldbus termination Passive LWL adapters can be connected Number of parameter bytes Number of diagnostic bytes Address range for PROFIBUS-DP Included in range of supply 5 V DC (from Bus Refreshing module) 4.7 to 5.3 VDC according to EN ma PS/2 socket 1 SUB-D socket, 9-pole 9.6 kbit/s to 12 MBit/s 2 hexadecimal rotary switches via SUB-D connector current consumption max. 100 ma 5 Bytes 3 Bytes 001 to 125 dec x x 74.4 mm 2x end bracket XN-WEW-35/2-SW 1x end plate XN-ABPL Ordering information Type BL20-GW-PBDP-12MB Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 23

24 Technical data Gateways Gateway PROFIBUS DP Gateway overview: This gateway principally fufils the same functions as the gateway BL-20GW-PBDP-12MB with the following restrictions: A maximum of 15 BL20 I/O modules may be connected From these 15, only 4 block type modules may be connected The software I/O assistant may only be used online for firmware download Packing of process data of the modules is not supported BL20 Gateway PROFIBUS BL20-GW-PBDP-12MB-STD Supply voltage Permissible range Residual ripple Nominal current consumption from module bus I MB Service interface Connection technology fieldbus Transmission speed Fieldbus addressing Fieldbus termination Passive LWL adapters can be connected Number of parameter bytes Number of diagnostic bytes Address range for PROFIBUS-DP Included in range of supply 5 V DC (from Bus Refreshing module) 4.7 to 5.3 VDC according to EN ma PS/2 socket 1 SUB-D socket, 9-pole 9.6 kbit/s to 12 MBit/s 2 hexadecimal rotary switches via SUB-D connector current consumption max. 100 ma 5 Bytes 3 Bytes 001 to 125 dec x x 74.4 mm 2x end bracket XN-WEW-35/2-SW 1x end plate XN-ABPL Ordering information Type BL20-GW-PBDP-12MB-STD Ident-number /1101 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

25 Technical data Gateways Gateway DeviceNet TM Gateway overview The gateway is the interface between the BL20 periphery modules and the DeviceNet TM It is responsible for the data exchange between the BL20 station and further DeviceNet TM stations The connection to the DeviceNet TM is made via Open Style Connector LEDs for indicating supply voltage, group diagnostics and bus errors BL20 Gateway DeviceNet TM Supply voltage Permissible range Residual ripple Nominal current from module bus I MB Service interface Connection technology fieldbus Transmission speed Fieldbus addressing Fieldbus termination Address range Included in range of supply BL20-GW-DNET 5 V DC (from Bus Refreshing module) 4.7 to 5.3 VDC according to EN ma PS/2 socket Open Style Connector 125/250/500 kbits/s 2 decimal rotary coding switches via DIP switches 0 to x x 74.4 mm 2x end bracket XN-WEW-35/2-SW 1x end plate XN-ABPL Ordering information Type BL20-GW-DNET Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 25

26 Technical data Gateways Gateway CANopen Gateway overview The gateway is the interface between the BL20 periphery modules and the CAN bus It is responsible for the data exchange between the BL20 station and further CANopen stations The connection to the CAN bus is made via 9-pole SUB-D connection or by direct wiring LEDs for indicating supply voltage, group diagnostics and bus errors BL20 Gateway CANopen Supply voltage Permissible range Residual ripple Nominal current consumption from module bus I MB Service interface Connection technology fieldbus Connection technology for direct wiring Addressing fieldbus Address range for CANopen Transmission rates Setting the transmission rate Fieldbus termination Included in range of supply BL20-GW-CANOPEN 5 V DC (from Bus Refreshing module) 4.7 to 5.3 VDC according to EN < 350 ma PS/2 socket 1x SUB-D socket, 9-pole 1x SUB-D plug, 9-pole 2x direct wiring tension clamp 2 hexadecimal rotary switches 001 to 127 (dec) kbit/s 800 kbit/s 500 kbit/s 250 kbit/s 125 kbit/s 50 kbit/s 20 kbit/s via DIP switch via SUB-D plug 50.6 x x 7.4 mm 2x end bracket XN-WEW-35/2-SW 1x end plate XN-ABPL Ordering information Type BL20-GW-CANOPEN Ident-number /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

27 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 27

28 Technical data power distribution modules Bus refreshing module Module overview Supply BL20 modules and gateway with a system nominal voltage of 5 VDC via the internal module bus Supply BL20 modules with nominal voltage of 24 VDC Can be used to create potential groups Base modules are available with or without connections to C-rails LEDs for indicating system and field supply as well as diagnostics Bus Refreshing module with diagnostics Electronic modules Nominal voltage System supply U SYS Permissible range for U SYS = 24 VDC Permissible range for U SYS = 5 VDC Field suppy U L Permissible range Ripple Residual ripple Maximum operating current I El Maximum system current supply I MB Number of diagnostic bits Base modules with gateway supply Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module with C Connection technology Designation for tension clamp Designation for screw connection Base modules without gateway supply Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module with C Connection technology Designation for tension clamp Designation for screw connection BL20-BR-24VDC-D 24 VDC 24 VDC / 5 VDC 18 to 30 VDC 4.7 to 5.3 VDC 24 VDC according to EN (18 to 30 VDC) < 5 % according to EN A 1.5 A 4 Bit 12.6 x 74.1 x 55.4 mm Connection for module bus light grey 2-/3-wire 12.6 x x 49.9 mm BL20-P3T-SBB BL20-P3S-SBB 4-wire 12.6 x x 49.9 mm BL20-P4T-SBBC BL20-P4S-SBBC Connection for module bus yellow 2-/3-wire 12.6 x x 49.9 mm BL20-P3T-SBB-B BL20-P3S-SBB-B 4-wire 12.6 x x 49.9 mm BL20-P4T-SBBC-B BL20-P4S-SBBC-B Only the modules BL20-P3x-SBB or BL20-P4x-SBBC (first module after the gateway) can be used to supply the gateway. Assignment of base modules: 1 Base module with gateway supply: light grey connection 2 Base module without gateway supply: yellow connection 28 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

29 Technical data power distribution modules Bus refreshing module Wiring diagram BL20-P4x-SBBC with gateway supply BL20-P4x-SBBC-B without gateway supply Wiring diagram BL20-P3x-SBB with gateway supply BL20-P3x-SBB-B without gateway supply 24 V DC Module bus supply + 24 V DC Module bus supply V DC Field supply V DC Field supply PE Ordering information Types Electronic module BL20-BR-24VDC-D Base modules BL20-P3T-SBB BL20-P3S-SBB BL20-P4T-SBBC BL20-P4S-SBBC BL20-P3T-SBB-B BL20-P3S-SBB-B BL20-P4T-SBBC-B BL20-P4S-SBBC-B Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 29

30 Technical data power distribution modules Power feeding modules with diagnostics Module overview Supply the BL20 I/O modules with a nominal voltage of 24 VDC or 120/230 VAC Can be used to create potential groups Base modules are available with or without connections to C-rails LEDs for indicating system and field supply as well as diagnostics Wiring diagram printed on the module cover Power Feeding module with diagnostics Electronic modules Nominal voltage Permissible range Field suppy U L Permissible range Nominal current from module bus I MB Ripple Residual ripple Maximum operating current I El Voltage anomalies Number of diagnostic bits Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module with C Connection technology Designation for tension clamp Designation for screw connection BL20-PF-24VDC-D 24 VDC 18 to 30 VDC 24 VDC according to EN (18 to 30 VDC) 28 ma < 5 % according to EN A according to EN and EN Bit 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-P3T-SBB BL20-P3S-SBB 4-wire 12.6 x x 49.9 mm BL20-P4T-SBBC BL20-P4S-SBBC BL20-PF-120/230VAC-D 120/230 V AC according to EN /230 V AC according to EN ma < 5 % according to EN A according to EN and EN Bit 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-P3T-SBB BL20-P3S-SBB 4-wire 12.6 x x 49.9 mm BL20-P4T-SBBC BL20-P4S-SBBC 30 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

31 Technical data power distribution modules Wiring diagrams: power feeding module Wiring diagram BL20-P3x-SBB for BL20-PF-24VDC-D Wiring diagram BL20-P4x-SBBC for BL20-PF-24VDC-D V DC PE Wiring diagram BL20-P3x-SBB for BL20-PF-120/230VCD-D Wiring diagram BL20-P4x-SBBC for BL20-PF-120/230VCD-D Ordering information Types Electronics modules BL20-PF-24VDC-D BL20-PF- 120/230VAC-D Base modules BL20-P3T-SBB BL20-P3S-SBB BL20-P4T-SBBC BL20-P4S-SBBC Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 31

32 Technical data digital input modules 2DI, 24 VDC Module overview Detection of digital input signals 24 VDC 2 channels, positive or negative switching Electronics galvanically isolated from the field level via optocoupler Base modules are available with or without connections to C-rails LEDs for indicating status and diagnostics Wiring diagram printed on the module cover Digital input module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Input voltage, nominal value at 24 VDC Low level U L High level U H Active level U A Inactive level U I Input current Low level I L High level I H Active level I A Inactive level I I Input delay t rise t fall 2-wire initiators can be connected Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module with C Connection technology Designation for tension clamp Designation for screw connection BL20-2DI-24VDC-P 2 24 VDC 20 ma 28 ma 0.7 W -30 V to +5 V 11 V to 30 V 0 ma to 1.5 ma 2 ma to 10 ma < 200 µs < 200 µs with a permissible closed-circuit current of 1.5 ma 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 4-wire 12.6 x x 49.9 mm BL20-S4T-SBBC BL20-S4S-SBBC BL20-2DI-24VDC-N 2 24 VDC 20 ma 28 ma 0.7 W 0 V to +5 V > (U PF - 11 V) 1.8 ma to 10 ma 0 ma to 1.7 ma < 200 µs < 200 µs with a permissible closed-circuit current of 1.5 ma 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 4-wire 12.6 x x 49.9 mm BL20-S4T-SBBC BL20-S4S-SBBC 32 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

33 Technical data digital input modules Wiring diagrams Wiring diagram BL20-S3x-SBB for BL20-2DI-24VDC-P Wiring diagram BL20-S4x-SBBC for BL20-2DI-24VDC-P Wiring diagram BL20-S3x-SBB for BL20-2DI-24VDC-N Wiring diagram BL20-S4x-SBBC for BL20-2DI-24VDC-N Ordering information Types Electronic modules BL20-2DI-24VDC-P BL20-2DI-24VDC-N Base modules BL20-S3T-SBB BL20-S3S-SBB BL20-S4T-SBBC BL20-S4S-SBBC Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 33

34 Technical data digital input modules 2 DI, 120/230 VAC, positive switching Module overview Detection of digital input signals 120/230 VDC 2 channels, positive switching Electronics galvanically isolated from the field level via optocoupler Base modules are available with or without connections to C-rails LEDs for indicating status and diagnostics Wiring diagram printed on the module cover Digital input module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Input voltage, nominal value at 120/230 V AC Low level U L High level U H Frequency range Input current Low level I L High level I H Input delay t rise t fall Maximum permissible wire capacity Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module with C Connection technology Designation for tension clamp Designation for screw connection BL20-2DI-120/230VAC-P 2 120/230 VAC 20 ma 28 ma < 1 W 0 to 20 V AC 79 V AC to 265 VAC 47.5 Hz to 63 Hz 0 ma to 1 ma 3 ma to 8 ma < 20 ms < 20 ms 141 nf at 79 VAC / 50 Hz 23 nf at 265 VAC / 50 Hz 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 4-wire 12.6 x x 49.9 mm BL20-S4T-SBBC BL20-S4S-SBBC 34 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

35 Technical data digital input modules Wiring diagrams Wiring diagram BL20-S3x-SBB Wiring diagram BL20-S4x-SBBC Ordering information Types Electronic modules BL20-2DI- 120/230VAC-P Base modules BL20-S3T-SBB BL20-S3S-SBB BL20-S4T-SBBC BL20-S4S-SBBC Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 35

36 Technical data digital input modules 4 DI, 24 VDC Module overview Detection of digital input signals 24 VDC 4 channels, positive and negative switching Electronics galvanically isolated from the field level via optocoupler Base modules are available with or without connections to C-rails LEDs for indicating status and diagnostics Wiring diagram printed on the module cover Digital input module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Input voltage, nominal value at 24 VDC Low Level U L High Level U H Active level U A Inactive level U I Input current Low Level I L High Level I H Active level I A Inactive level I I Input delay t rise t fall Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module without C Connection technology Designation for tension clamp Designation for screw connection BL20-4DI-24VDC-P 4 24 VDC 40 ma 29 ma < 1 W -30 V to +5 V 15 V to 30 V 0 ma to 1.5 ma 2 ma to 10 ma < 200 µs < 200 µs 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-S4T-SBBSBB BL20-S4S-SBBSBB 4x 2-/3-wire 12.6 x x 49.9 mm BL20-S6T-SBBSBB BL20-S6S-SBBSBB BL20-4DI-24VDC-N 4 24 VDC 40 ma 28 ma < 1 W 0 V to +5 V > (U PF - 11 V) 1.3 ma to 6 ma 0 ma to 1.2 ma < 200 µs < 200 µs 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-S4T-SBBSBB BL20-S4S-SBBSBB 4x 2-/3-wire 12.6 x x 49.9 mm BL20-S6T-SBBSBB BL20-S6S-SBBSBB 36 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

37 Technical data digital input modules Wiring diagrams Wiring diagram BL20-S4x-SBBS for BL20-4DI-24VDC-P Wiring diagram BL20-S6x-SBBSBB for BL20-4DI-24VDC-P S S S S Wiring diagram BL20-S4x-SBBS for BL20-4DI-24VDC-N Wiring diagram BL20-S6x-SBBSBB for BL20-4DI-24VDC-N S S S S Ordering information Types Electronic modules BL20-4DI-24VDC-P BL20-4DI-24VDC-N Base modules BL20-S4T-SBBS BL20-S4S-SBBS BL20-S6T-SBBSBB BL20-S6S-SBBSBB Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 37

38 Technical data digital input modules 16/32 DI, 24 VDC, positive switching Module overview Detection of digital input signals 24 VDC 16 or 32channels, positive switching Electronics galvanically isolated from the field level via optocoupler Base modules are available with or without connections to C-rails LEDs for indicating status and diagnostics Wiring diagram printed on the module cover Digital input module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Input voltage, nominal value at 24 VDC Low Level U L High Level U H Input current Low Level I L High Level I H Input delay t rise t fall Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module with C Connection technology Designation for tension clamp Designation for screw connection BL20-16DI-24VDC-P VDC 40 ma 45 ma < 2.5 W -30 V to +5 V 15 V to 30 V 0 ma to 1.5 ma 2 ma to 10 ma < 200 µs < 200 µs x 74.1 x 55.4 mm 16 x 2-/3-wire x x 49.9 mm BL20-B3T-SBB BL20-B3S-SBB 16 x 4-wire x x 49.9 mm BL20-B4T-SBBC BL20-B4S-SBBC BL20-32DI-24VDC-P VDC < 30 ma < 30 ma < 4.2 W -30 V to +5 V 15 V to 30 V < 1.5 ma 2 ma to 10 ma < 200 µs < 200 µs x 74.1 x 55.4 mm 32 x 2-/3-wire 100,8 x 154,5 x 49,9 BL20-B6T-SBBSBB BL20-B6S-SBBSBB 38 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

39 Technical data digital input modules Wiring diagrams Wiring diagram BL20-B3x-SBB for BL20-16DI-24VDC-P Wiring diagram BL20-B4x-SBBCfor BL20-16DI-24VDC-P Wiring diagram BL20-B6x-SBBSBB for BL20-32DI-24VDC-P S S S S Ordering information Types Electronic modules BL20-16DI-24VDC-P BL20-32DI-24VDC-P Base modules BL20-B3T-SBB BL20-B3S-SBB BL20-B4T-SBBC BL20-B4S-SBBC BL20-B6T-SBBSBB BL20-B6S-SBBSBB Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 39

40 Technical data analogue input modules 1AI-I, 2 AI-I Module overview Detection of standard analogue input signals: current or voltage Electronics galvanically isolated from the field level via optocoupler Deployment of shielded cables Base modules available with or without sensor supply Potential-free or potential-linked connection of sensor supply LEDs for indicating diagnostics Wiring diagram printed on the module cover Analogue input module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Input current Max. input current Input resistance (burden) Cutoff frequency (-3 db) Basic error at 23 C Repeat accuracy Temperature coefficient Resolution of A/D converter Measuring principle Measurement value representation Sensor supply Number of diagnostic bits Number of parameter bits Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module without C, intended for sensor supply Connection technology Designation for tension clamp Designation for screw connection BL20-1AI-I(0/4...20MA) 1 24 VDC 50 ma 41 ma < 1 W 0/4 to 20 ma 50 ma < 125 Ω 200 Hz < 0.2 % 0.09 % 300 ppm/ C from end value 14 Bit signed integer gradual approximation 16 Bit signed integer / 12 Bit full-range left-justified Bridged with L+ and L- from the power supply; not short-circuit proof 2 Bit 3 Bit 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 4-wire 12.6 x x 49.9 mm BL20-S4T-SBBS BL20-S4S-SBBS BL20-2AI-I(0/4...20MA) 2 24 V DC 12 ma 35 ma < 1 W 0/4 to 20 ma 50 ma 125 Ω 50 Hz < 0.2 % 0.05 % 300 ppm/ C from end value 16 Bit delta sigma 16 Bit signed integer / 12 Bit full-range left-justified 250 ma; Bridged with L+ and L- from the power supply; not short-circuit proof 1 Bit 1 Byte (per channel) 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 4-wire 12.6 x x 49.9 mm BL20-S4T-SBBS BL20-S4S-SBBS 40 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

41 + + Technical data analogue input modules Wiring diagrams Wiring diagram BL20-S3x-SBB for BL20-1AI-I(0/4...20MA), analogue sensor without sensor supply Wiring diagram BL20-S4x-SBBS, for BL20-1AI-I(0/4...20MA), analogue sensor with potential-free sensor supply Wiring diagram BL20-S3x-SBB for BL20-2AI-I(0/4...20MA), analogue sensor without sensor supply Wiring diagram BL20-S4x-SBBS for BL20-2AI-I(0/4...20MA), analogue sensor with potential-bound sensor supply U h + U h + Sh Sh Sh Sh Ordering information Types Electronic modules BL20-1AI-I(0/4...20MA) BL20-2AI-I(0/4...20MA) Base modules BL20-S3T-SBB BL20-S3S-SBB BL20-S4T-SBBS BL20-S4S-SBBS Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 41

42 Technical data analogue input modules 1AI-U, 2 AI-U Module overview Detection of standard analogue input signals: voltage Electronics galvanically isolated from the field level via optocoupler Use of shielded cables Base modules available with or without sensor supply Potential-free or potential-bound connection of sensor supply LEDs for indicating diagnostics Wiring diagram printed on the module lid Analogue input module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Input voltage Max. input voltage Input resistance (burden) Cutoff frequency (-3 db) Basic error at 23 C Repeat accuracy Temperature coefficient Resolution of A/D converter Measuring principle Measurement value representation Sensor supply Number of diagnostic bits Number of parameter bits Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module without C, intended for sensor supply Connection technology Designation for tension clamp Designation for screw connection BL20-1AI-U(-10/ VDC) 1 24 VDC 50 ma 41 ma < 1 W -10/0 to +10 VDC 35 V continuous 98.5 kω 200 Hz < 0.2 % 0.05 % 300 ppm/ C of end value 14 Bit signed integer gradual approximation 16 Bit signed integer / 12 Bit signed integer left-justified / 12 Bit full-range left-justified Bridged with L+ and L- from the power supply; not short-circuit proof 1 Bit 3 Bit 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 4-wire 12.6 x x 49.9 mm BL-S4T-SBBS BL-S4S-SBBS BL20-2AI-U( 10/ VDC) 2 24 VDC 12 ma 35 ma < 1 W -10/0 to +10 VDC 35 V continuous 98.5 k Ω 50 Hz < 0.2 % 0.05 % 150 ppm/ C of end value 16 Bit delta sigma 16 Bit signed integer / 12 Bit full range left-justified 250 ma; bridged with L+ and L- from the power supply; not short-circuit proof 2 Bit 2 Byte 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 BL20-S3T-SBB BL20-S3S-SBB 4-wire 12.6 x x 49.9 BL20-S4T-SBBS BL20-S4S-SBBS 42 /1101 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

43 + + Technical data analogue input modules Wiring diagrams Wiring diagram BL20-S3x-SBB for BL20-1AI-U(10/ VDC), analogue sensor without sensor supply Wiring diagram BL20-S4x-SBBS, for BL20-1AI-U(10/ VDC), analogue sensor with potential-free sensor supply Wiring diagram BL20-S3x-SBB for BL20-2AI-U(-10/ V), analogue sensor without sensor supply Wiring diagram BL20-S4x-SBBS for BL20-2AI-U(-10/ V), analogue sensor with potential-bound sensor supply U h + U h + Sh Sh Sh Sh Ordering information Types Electronic modules BL20-1AI-U (-10/ VDC) BL20-2AI-U (-10/ VDC) Base modules BL20-S3T-SBB BL20-S3S-SBB BL20-S4T-SBBS BL20-S4S-SBBS Ident-no Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 43

44 Technical data analogue input modules 2 AI-PT/Ni Module overview Detection of standard analogue input signals for measurement of temperatures Connection of platinum sensors PT100, PT500 and PT1000 as well as nickel sensors Ni100 and Ni1000 Connection of sensors in 2- or 3-wire technology Electronics galvanically isolated from the field level via optocoupler Base modules available with or without sensor supply LEDs for indicating diagnostics Wiring diagram printed on the module cover Analogue input module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Measurement current Destruction limit Platinum sensors Nickel sensors Measurement value representation Offset error Linearity Basic error at 23 C Repeat accuracy Temperature coefficient Cycle time Connectable sensors Platinum sensors Nickel sensors Number of parameter bytes Number of diagnostic bytes Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Connection technology Designation for tension clamp Designation for screw connection BL20-2AI-PT/NI-2/ VDC < 30 ma 45 ma < 1 W < 1 ma > 30 VDC according to DIN IEC 751 according to DIN Bit signed integer / 12 Bit full-range left-justified 0.1 % < 0.1 % < 0.2 % 0.05 % 300 ppm/ C from end value 130 ms per channel PT100, PT500, PT1000 Ni100, Ni Byte (2 Byte per channel) 2 Byte (1 Byte per channel) 12.6 x 74.1 x 55.4 mm 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 4-wire 12.6 x x 49.9 mm BL20-S4T-SBBS BL20-S4S-SBBS 44 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

45 Technical data analogue input modules Wiring diagrams Wiring diagram BL20-S3x-SBB, 2-wire connection Wiring diagram BL20-S4x-SBBS, 3-wire connection Ordering information Types Electronic modules BL20-2AI-PT/NI-2/3 Base modules BL20-S3T-SBB BL20-S3S-SBB BL20-S4T-SBBS BL20-S4S-SBBS Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 45

46 Technical data analogue input modules 2 AI-Thermo Module overview Detection of standard analogue input signals for measurement of temperatures Connection of thermoelements of the types B,E, J, K, N, R, S and T Electronics galvanically isolated from the field level via optocoupler Base modules with internal cold junction compensation LEDs for indicating diagnostics Wiring diagram printed on the module cover Analogue input module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Destruction limit Sensors Temperature ranges Type B Type E Type J Type K Type N Type R Type S Type T Voltage measurements (resolution) ± 50 mv ± 100 mv ± 500 mv ± 1 V Measurement value representation Offset error Linearity Basic error at 23 C Repeat accuracy Temperature coefficient Cycle time Number of parameter bytes Number of diagnostic bytes Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection BL20-2AI-THERMO-PI 2 24 VDC < 30 ma 45 ma < 1 W > 30 VDC according to DIN IEC 584, Class 1, 2, to C -270 to C -210 to C -270 to C -270 to C -50 to C -50 to C -270 to C < 2 µv < 4 µv < 20 µv < 50 µv 16 Bit signed integer / 12 Bit full-range left-justified 0.1 % < 0.1 % < 0.2 % 0.05 % 300 ppm/ C from end value 60 ms per channel ms 2 Byte (1 Byte per channel) 2 Byte (1 Byte per channel) 12.6 x 74.1 x 55.4 mm 4-wire with integrated cold junction compensation 12.6 x x 49.9 mm BL20-S4T-SBBS-CJ BL20-S4S-SBBS-CJ 46 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

47 Technical data analogue input modules Wiring diagrams Wiring diagram BL20-S4x-SBBS-CJ i PT a PT i Cold junction compensation in base module Ordering information Types Electronic modules BL20-2AI-THERMO-PI Base modules BL20-S4T-SBBS-CJ BL20-S4S-SBBS-CJ Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 47

48 Technical data digital output modules 2 DO, 24 VDC Module overview Output of digital output signals 24 VDC 2 channels, positive and negative switching, with 0.5 A max. output current 2 channels, positive switching, with 2 A max. output current Electronics galvanically isolated from the field level via optocoupler LEDs for indicating status and diagnostics Wiring diagram printed on the module cover Digital output module BL20-2DO-24VDC-0.5A-P BL20-2DO-24VDC-0.5A-N BL20-2DO-24VDC-2A-P Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Output voltage (loaded) Active level U A High level U H Output current Active level I A (nominal value) Active level I A (permissible range) High level I H (nominal value) High level I H (permissible range) Delay at signal change and resistive load (R LO < 1 k ) from inactive to active level from active to inactive level from low to high level from high to low level Load impedance range Synchronization factor Connectable are Load impedance, resistive R LO Load impedance, inductive R LI Lamp load R LL Switching frequency Resistive load Inductive load Lamp load Number of diagnostic bits 2 24 VDC 20 ma (when load current = 0) 32 ma 1 W min. L+ (-1 V) 0.5 A < 0.6 A < 100 µs < 100 µs 48 Ω to 1 kω 100 % resistive and inductive loads as well as lamp loads min. 48 Ω max. 1.2 H max. 3 W 5 khz (R LO < 1 kω) 10 Hz 2 Bit 12.6 x 74.1 x 55.4 mm 2 24 VDC 20 ma (when load current = 0) 32 ma 1 W max. GND (+1 V) 0.5 A < 0.6 A < 100 µs < 100 µs 100 % resistive and inductive loads as well as lamp loads min. 48 Ω max. 1.2 H max. 12 W 100 Hz (R LO < 1 kω) 2 Hz 10 Hz 2 Bit 12.6 x 74.1 x 55.4 mm 2 24 VDC < 50 ma (when load current = 0) 33 ma 1 W min. L+ (-1 V) 2 A < 2.4 A < 100 µs < 100 µs 12 Ω to 1 kω 100 % resistive and inductive loads as well as lamp loads min. 12 Ω max. 1.2 H max. 6 W 5 khz (R LO < 1 kω) 10 Hz 2 Bit 12.6 x 74.1 x 55.4 mm Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module with C Connection technology Designation for tension clamp Designation for screw connection 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBC BL20-S3S-SBC 4-wire 12.6 x x 49.9 mm BL20-S4T-SBCS BL20-S4S-SBCS 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBC BL20-S3S-SBC 4-wire 12.6 x x 49.9 mm BL20-S4T-SBCS BL20-S4S-SBCS 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBC BL20-S3S-SBC 4-wire 12.6 x x 49.9 mm BL20-S4T-SBCS BL20-S4S-SBCS 48 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

49 Technical data digital output modules Wiring diagrams Wiring diagram BL20-P3x-SBC for BL20-2DO-24VDC-0.5A-P Wiring diagram BL20-P4x-SBCS for BL20-2DO-24VDC-0.5A-P Wiring diagram BL20-P3x-SBC for BL20-2DO-24VDC-0.5A-N Wiring diagram BL20-P4x-SBCS for BL20-2DO-24VDC-0.5A-N Wiring diagram BL20-P3x-SBC for BL20-2DO-24VDC-2A-P Wiring diagram BL20-P4x-SBCS for BL20-2DO-24VDC-2A-P Ordering information Types Electronic modules BL20-2DO-24VDC-0.5A-P BL20-2DO-24VDC-0.5A-N BL20-2DO-24VDC-2A-P Base modules BL20-S3T-SBC BL20-S3S-SBC BL20-S4T-SBCS BL20-S4S-SBCS Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 49

50 Technical data digital output modules 4 DO, 24 V DC Module overview Output of digital output signals 24 V DC 4 channels, positive switching, with 0.5 A max. output current Electronics galvanically isolated from the field level via optocoupler LEDs for indicating status and diagnostics Wiring diagram printed on the module lid Digital output module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Output voltage (loaded) Active level U A High level U H Output current High level I H (nominal value) High level I H (short-time overload) Delay at signal change and resistive load (R LO < 1 k ) from low to high level from high to low level Load impedance range Synchronization factor Connectable are Load impedance, resistive R LO Load impedance, inductive R LI Lamp load R LL Switching frequency Resistive load Inductive load Lamp load Number of diagnostic bits Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module with C Connection technology Designation for tension clamp Designation for screw connection BL20-4DO-24VDC-0.5A-P 4 24 V DC 25 ma (when load current = 0) 30 ma < 1 W min. L+ (-1 V) 0.5 A < 1.0 A for max. 5 min. < 250 µs < 250 µs 48 Ω to 1 kω 100 % resistive and inductive loads as well as lamp loads min. 48 Ω max. 1.2 H max. 6 W 5 khz (R LO < 1 kω) 2 Hz 10 Hz 1 Bit 12.6 x 74.1 x 55.4 mm 4-wire 12.6 x x 49.9 mm BL20-S4T-SBCS BL20-S4S-SBCS 4 x 2/3-wire 12.6 x 154,5 x 49.9 mm BL20-S4T-SBCSBC BL20-S4S-SBCSBC 50 /1101 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

51 Technical data digital output modules Wiring diagram Wiring diagram BL20-S4x-SBCS for BL20-4DO-24VDC-0.5A-P Wiring diagram BL20-S6x-SBCSBC for BL20-4DO-24VDC-0.5A-P S S S S PE PE S S S S PE PE Ordering information Type Electronic modules BL20-4DO-24VDC-0.5A-P Base modules BL20-S4T-SBCS BL20-S4S-SBCS BL20-S6T-SBCSBC BL20-S6S-SBCSBC Ident.-no Hans Turck GmbH Hans & Turck Co.KG GmbH D & Co.KG Mülheim D an der Mülheim Ruhr an Tel. der 0208/ Ruhr Tel. 0208/ Fax 0208/ Fax 0208/ turckmh@mail.turck-globe.de turckmh@mail.turck-globe.de / / 51

52 Technical data digital output modules 16/32 DO, 24 VDC Module overview Output of digital output signals 24 VDC 16 or 32 channels, positive switching, with 0.5 A max. output current Electronics galvanically isolated from the field level via optocoupler LEDs for indicating status and diagnostics Wiring diagram printed on the module cover Digital output module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Output voltage, High level (loaded) Output current High level I H (nominal value) High level I H (permissible range) Delay by signal change and resistive load from low to high level from high to low level Connectable are Load impedance, resistive R LO Load impedance, inductive R LI Lamp load R LL Switching frequency (resistive load) Number of diagnostic bits Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection BL20-16DO-24VDC-0.5A-P VDC 30 ma 45 ma < 4 W min. L+ (-1V) 0.5 A < 0.6 A R LO < 1 kω typ. 100 µs typ. 100 µs resistive and inductive loads as well as lamp loads > 48 kω Category DC 13 according to EN max. 3 W 100 Hz (R LO < 1 kω) x 74.1 x 55.4 mm 2-/3-wire x x 49.9 mm BL20-B3T-SBC BL20-B3S-SBC BL20-32DO-24VDC-0.5A-P available from end of /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

53 Technical data digital output modules Wiring diagrams Wiring diagram BL20-B3x-SBC Ordering information Types Electronic modules BL20-16DO-24VDC-0.5A-P BL20-32DO-24VDC-0.5A-P Base modules BL20-B3T-SBC BL20-B3S-SBC Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 53

54 Technical data analogue output modules 1 AO-I, 2 AO-I, 2 AO-U Module overview Detection of standard analogue output signals 1 channel current and 2 channels voltage Electronics galvanically isolated from the field level via optocoupler Use shielded cables LEDs for indicating diagnostics Wiring diagram printed on the module cover Analogue output module BL20-1AO-I(0/4...20MA) BL20-2AO-I(0/4...20MA) BL20-2AO-U( 10/ VDC) Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Output voltage Output current Burden resistance Resistive load R LO Inductive load R LI Capacitive load R LK Short-circuit current Transmission frequency Basic error at 23 C Repeat accuracy Output ripple Temperature coefficient Settling time (maximal) Resistive load Inductive load Capacitive load Interference voltage suppression Common mode Normal mode Interference between channels Measurement value representation Number of parameter bytes 1 24 VDC 50 ma 39 ma < 1 W 0/4 to 20 ma < 450 Ω < 1 mh < 200 Hz 0.2 % 0.05 % 0.02 % 300 ppm/ C from end value 0.1 ms 0.5 ms 0.5 ms 16 Bit signed integer / 12 Bit full-range left-justified Negative values are put out as 0 ma or as 4 ma, depending on the parameterized measurement range. 3 Byte 12.6 x 74.1 x 55.4 mm 2 24 VDC < 50 ma < 40 ma < 1 W 0/4 bis 20 ma < 450 < 1 mh < 200 Hz 0.2 % 150 ppm/ C from end value 2 ms 2 ms 16 Bit signed Integer / 12 Bit full-range left-justified Negative values are put out as 0 ma or as 4 ma, depending on the parameterized measure ment range. 3 Bytes (per channel) 12.6 x 74.1 x 55.4 mm 2 24 VDC 50 ma 43 ma < 1 W -10/0 to +10 VDC > 1 kω > 1 µf 40 ma < 100 Hz < 0.2 % 0.05 % 0.02 % 300 ppm/ C from end value 0.1 ms 0.5 ms 0.5 ms > 90 db > 70 db > -50 db 16 Bit signed integer / 12 Bit signed integer leftjustified / 12 Bit full-range leftjustified Negative values are automatically put out as 0 when the measurement range is parameterized between 0 to +10 VDC. 6 Bytes (3 Bytes per channel) 12.6 x 74.1 x 55.4 mm Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 2-/3-wire 12.6 x x 49.9 mm BL20-S3T-SBB BL20-S3S-SBB 54 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

55 + Technical data analogue output modules Wiring diagrams Wiring diagram BL20-S3x-SBB for BL20-1AO-I(0/4...20MA) Wiring diagram BL20-S3x-SBB for BL20-2AO-I(0/4...20MA) Wiring diagram BL20-S3x-SBB for BL20-2AO-U(-10/ V) Sh Sh Ordering information Types Electronic modules BL20-1AO-I(0/4...20MA) BL20-2AO-I(0/4...20MA) BL20-2AO-U( 10/ VDC) Base modules BL20-S3T-SBB BL20-S3S-SBB Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 55

56 Technical data relay modules 2 DO-R, 24 V DC Module overview Output of digital output signals Suitable for solenoid valves, D.C. contactors and signaling lamps nominal load voltage range 24 VDC/VAC to 230 VAC 2 channels as NC, NO or changeover contacts Electronics from the supply galvanically isolated LEDs for indicating status and diagnostics Wiring diagram printed on the module cover Relay module BL20-2DO-R-NC BL20-2DO-R-NO BL20-2DO-R-CO Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Connectable are Nominal load voltage Output current with AC voltage 230 VAC Max. continuous current (resistive) Min. load current (recommended) Output current bei DC voltage (resistive) Synchronization factor Min. number of switching cycles (230 VAC, resistive load) 5 A 0.5 A 2, normally-closed contact 24 VDC 20 ma 28 ma 1 W resistive and inductive loads as well as lamp loads 230 VAC / 30 VDC 2 A (5 A, depending on load) 10 ma at 12 VDC see load limit curve 100 % 1 x x x 74.1 x 55.4 mm 2, normally-open contact 24 V DC 20 ma 28 ma 1 W resistive and inductive loads as well as lamp loads 230 VAC / 30 VDC 2 A (5 A, depending on load) 10 ma at 12 VDC see load limit curve 100 % 1x x x 74.1 x 55.4 mm 2, changeover, galvanically isolated 24 VDC 20 ma 28 ma 1 W resistive and inductive loads as well as lamp loads 230 VAC / 30 VDC 2 A (5 A, depending on load) 10 ma at 12 VDC see load limit curve 100 % 1x x x 74.1 x 55.4 mm Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection Base module with C Connection technology Designation for tension clamp Designation for screw connection 4-wire 12.6 x x 49.9 mm BL20-S4T-SBBS BL20-S4S-SBBS 4-wire 12.6 x x 49.9 mm BL20-S4T-SBCS BL20-S4S-SBCS 4-wire 12.6 x x 49.9 mm BL20-S4T-SBBS BL20-S4S-SBBS 4-wire 12.6 x x 49.9 mm BL20-S4T-SBCS BL20-S4S-SBCS 4-wire 12.6 x x 49.9 mm BL20-S4T-SBBS BL20-S4S-SBBS Ordering information Types Electronic modules BL20-2DO-R-NC BL20-2DO-R-NO BL20-2DO-R-CO Base modules BL20-S4T-SBBS BL20-S4S-SBBS BL20-S4T-SBCS BL20-S4S-SBCS Ident-number /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

57 Technical data relay modules Load limit curve, wiring diagram, module circuit diagram Load limit curve Definition: At 1000 switching cycles, no sustained arcs with a burning life of > 10 ms may occur. Wiring diagram BL20-S4x-SBBS with externally connected supply and cross-connected root for BL20-2DO-R-NC Module circuit diagram BL20-S4x-SBBS for BL20-2DO-R-NC ➀ Bridged in the electronics ➁ Cross-connection via jumper in the base module Wiring diagram BL20-S4x-SBCS with supply via C-rail and cross-connected root for BL20-2DO-R-NC Module circuit diagram BL20-S4x-SBCS for BL20-2DO-R-NC ➀ Supply via C-rail ➁ max. 8 relay modules ➀ C-rail ➁ Cross-connection via jumper in the base module Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 57

58 Technical data relay modules Wiring diagrams, module circuit diagrams Wiring diagram BL20-S4x-SBBS with externally connected supply and crossconnected root for BL20-2DO-R-NO Module circuit diagram BL20-S4x-SBBS for BL20-2DO-R-NO R2 R NO NO 1 a Electronics module RT RT 1 b ➀ Bridged in the electronics ➁ Cross-connection via jumper in the base module Wiring diagram BL20-S4x-SBCS with supply via C-rail and cross-connected root for BL20-2DO-R-NO Module circuit diagram BL20-S4x-SBCS for BL20-2DO-R-NO ➀ C-rail ➁ Cross-connection via jumper in the base module ➀ Supply via C-rail ➁ max. 8 relay modules 58 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

59 Technical data relay modules Wiring diagrams, module circuit diagrams Wiring diagram BL20-S4x-SBBS for BL20-2DO-R-CO Module circuit diagram BL20-S4x-SBBS for BL20-2DO-R-CO Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 59

60 Technical data counter module 1 CNT, 24 VDC Module overview Detection of standard counter signals 1 channel digital input 24 VDC 1 channel digital output 24 VDC, 2 A Counter mode, continuous count, single-action count or period duration measurement Measurement mode: frequency measurement, revolutions measurement, perid duration measurement Electronics galvanically isolated from the field level via optocoupler LEDs for indicating diagnostics Wiring diagram printed on the module cover Counter module Electronic modules Number of channels Nominal voltage through supply terminal Nominal current from supply terminal I El Nominal current from module bus I MB Power loss of the module, typical Sensor supply Output voltage Output current Count signals and digital input Input voltage at nominal value 24 VDC Low level U L High level U H Input current Low level I L High level I H Input delay Min. pulse width (max. count frequency) Filter on Filter off Digital output Output voltage at nominal value 24 VDC Low level U L High level U H Output current High level I H (permissible range) High level I H (nominal value) Switching frequency with resistive load with inductive load with lamp load Lamp load RLL Output delay (resistive load) Short-circuit proof Response threshold Inductive reset Measurement ranges Frequency measurement Revolutions measurement Period duration measurement BL20-1CNT-24VDC 1 24 VDC < 50 ma (when load current = 0) < 40 ma 1.3 W L+ (-0.8 V) 0.5 A, short-circuit proof -30 VDC to 5 VDC 11 VDC to 30 VDC -8 ma to 1.5 ma 2 ma to 10 ma 200 µs > 25 ms (20 khz) < 2.5 ms (200 khz) 3 VDC L+ (-1 V) 5 ma to 2 A to 0.5 A (55 C) 100 Hz 2 Hz 10 Hz 10 W 100 µs Yes 2.6 A to 4 A L+ (-50 to -60 V) 0.1 Hz to 200 khz 1 rev/min to rev/min 5 ms to 120 s 60 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

61 Technical data counter module 1 CNT, 24 VDC Counter module Counter modes Signal evaluation A, B Counter mode Hysteresis Pulse duration Synchronization Count limits Upper count limit Lower count limit Measurement modes Signal evaluation A, B Number of diagnostic bytes Number of parameter bytes Base modules Base module without C Connection technology Designation for tension clamp Designation for screw connection BL20-1CNT-24VDC Pulse and direction / Sensor single / double / fourfold Continuous / single-action / periodical 0 to to 255 Single-action / periodical 0 to 7FFF FFFF to FFFF FFFF Pulse and direction / sensor single 1 Byte 15 Byte 12.6 x 74.1 x 55.4 mm 4-wire 12.6 x 74.1 x 55.4 mm BL20-S4T-SBBS BL20-S4S-SBBS Ordering Information Types Electronic modules BL20-1CNT-24VDC Base module BL20-S4T-SBBS BL20-S4S-SBBS Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 61

62 Technical data counter module Wiring diagram Wiring diagram BL20-S4x-SBBS 62 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

63 Notes Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 63

64 BL20 module guide Base modules with tension clamp Electronic modules Base modules BL20-S3T-SBB BL20-S3T-SBC BL20-S4T-SBBC BL20-S4T-SBBS BL20-S4T-SBCS BL20-S4T-SBBS-CJ BL20-S6T-SBBSBB BL20-S6T-SBCSBC BL20-B3T-SBB BL20-B3T-SBC BL20-B4T-SBBC BL20-B6T-SBBSBB BL20-P3T-SBB BL20-P3T-SBB-B BL20-P4T-SBBC BL20-P4T-SBBC-B Digital input modules BL20-2DI-24VDC-P BL20-2DI-24VDC-N BL20-2DI-120/230VAC BL20-4DI-24VDC-P BL20-4DI-24VDC-N BL20-16DI-24VDC-P BL20-32DI-24VDC-P Analogue input modules BL20-1AI-I(0/4...20MA) BL20-2AI-I(0/4...20MA) BL20-1AI-U(-10/ VDC) BL20-2AI-U(-10/ VDC) BL20-2AI-PT/NI-2/ BL20-2AI-THERMO-PI Digital output modules BL20-2DO-24VDC-0.5A-P BL20-2DO-24VDC-0.5A-N BL20-2DO-24VDC-2A-P BL20-4DO-24VDC-0.5A-P BL20-16DO-24VDC-0.5A-P Analogue output modules BL20-1AO-I(0/4...20MA) BL20-2AO-I(0/4...20MA) BL20-2AO-U(-10/ VDC) Relay modules BL20-2DO-R-NC BL20-2DO-R-NO BL20-2DO-R-CO Technology modules BL20-1CNT-24VDC Supply modules BL20-BR-24VDC-D BL20-PF-24VDC-D BL20-PF-120/230VAC-D /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

65 BL20 module guide Base modules with screw connection Electronic modules Base modules BL20-S3S-SBB BL20-S3S-SBC BL20-S4S-SBBC BL20-S4S-SBBS BL20-S4S-SBCS BL20-S4S-SBBS-CJ BL20-S6S-SBBSBB BL20-S6S-SBCSBC BL20-B3S-SBB BL20-B3S-SBC BL20-B4S-SBBC BL20-B6S-SBBSBB BL20-P3S-SBB BL20-P3S-SBB-B BL20-P4S-SBBC BL20-P4S-SBBC-B Digital input modules BL20-2DI-24VDC-P BL20-2DI-24VDC-N BL20-2DI-120/230VAC BL20-4DI-24VDC-P BL20-4DI-24VDC-N BL20-16DI-24VDC-P BL20-32DI-24VDC-P Analogue input modules BL20-1AI-I(0/4...20MA) BL20-2AI-I(0/4...20MA) BL20-1AI-U(-10/ VDC) BL20-2AI-U(-10/ VDC) BL20-2AI-PT/NI-2/ BL20-2AI-THERMO-PI Digital output modules BL20-2DO-24VDC-0.5A-P BL20-2DO-24VDC-0.5A-N BL20-2DO-24VDC-2A-P BL20-4DO-24VDC-0.5A-P BL20-16DO-24VDC-0.5A-P Analogue output modules BL20-1AO-I(0/4...20MA) BL20-2AO-I(0/4...20MA) BL20-2AO-U(-10/ VDC) Relay modules BL20-2DO-R-NC BL20-2DO-R-NO BL20-2DO-R-CO Technology modules BL20-1CNT-24VDC Supply modules BL20-BR-24VDC-D BL20-PF-24VDC-D BL20-PF-120/230VAC-D Base module for gateway supply/++ Base module for bus refreshing within the station Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 65

66 Software I/Oassistant software for the BL20 station Overview Diagnostic software for project planning configuration parameterization Description The diagnostic and project planning software I/Oassistant supports the complete planning and realization of an I/O system. It is of assistance when planning the station as well as with the configuration and parameterization in both online and offline modes. Installations can be commissioned and tests and diagnostics carried out with the help of the software. Functions Example projects Projects can be created on the monitor, structured and extended according to needs Selection of the required modules Plausibility tests of the station Offline configuration and parameterization of individual stations Detailed project documentation Online help Online configuration and parameterization of individual stations Creation of station-specific GSD files Commissioning of stations Reading and setting of process data Diagnostic and error correction Download of new firmware in to the BL20 gateway Resetting of a BL20 station Ordering information Type SW-I/OASSISTANT XN-PS2-CABLE Ident-number /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

67 Software busstop Monitor - monitoring / commisioning software for PROFIBUS-DP Overview Monitoring/Introduction software for PROFIBUS-DP Graphic representation of stations Error diagnostics Manufacturer independent Fieldbus communication via various standard interfaces Module test of analogue and digital input and output modules via graphic elements Description The software tool busstop monitor supports both commissioning of the I/O modules and error diagnostics. Fieldbus stations are displayed graphically. Up-to-date data that is in the process of being transported via the bus can be displayed on the monitor (bus monitor). Further features: Communications interface - PROFIBUS-DP via the serial interface (RS232) of the PC or laptop Parameterization of stations (PROFIBUS-DP) Reading/writing of input/output data in hexadecimal, decimal and binary formats Plaintext display via connected stations Setting of individual outputs and test functions Recording of input data Reading of diagnostic data (additional plaintext display) Alteration of the station address (if this function is supported by the station) Display of non-replying stations (cyclical query function) Storing of current configuration User-friendly graphic interface Operating system WINDOWS 95/98 and NT WINDOWS Explorer look & feel Ordering information Type SW busstop monitor DP busstop monitor adapter cable DP-BM-M12 adapter Ident-number Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 67

68 Accessories guide Designation Description Type Ident-No. Marking material Labels for labelling electronic modules DIN A5 sheets, slice, perforated (laser print) 5 x 57 labels XN-LABEL/SCHEIBE Markers Connector markers DIN A5 sheets, block, perforated (laser print) 5 x 6 labels for labeling base modules, color identification for clear recognition of potentials in the connection level of the base modules (strip of 10 x 6): blue red green black brown red / blue green / yellow white Dekafix (50 labels per carrier foil/10 foils) XN-LABEL/BLOCK XN-ANBZ-BL XN-ANBZ-RT XN-ANBZ-GN XN-ANBZ-SW XN-ANBZ-BR XN-ANBZ-RT/BL-BED XN-ANBZ-GN/GE-BED XN-ANBZ-WS labelled 1-50 labelled labelled labelled FW5/1-50 FW5/ FW5/ FW5/ Mechanical accessories Jumpers for relays (QVR) Coding for electronic and base modules for bridging the 4th connection level (14/24) of base modules for relays /10 pcs. 1 grid 2 grid 3 grid 4 grid 5 grid 6 grid 7 grid 8 grid for coding slots of electronic and base modules (10 coding pieces per packing unit) Electronic module, type BL20-*DI-24VDC* Electronic module, type BL20-*DO-24VDC* Electronic module, type BL20-2DO-R-NO Electronic module, type BL20-2DO-R-NC Electronic module, type BL20-2DO-R-CO Electronic module, type BL20-1AI- I(0/4...20MA) Electronic module, type BL20-1AI-U (-10/ V) Electronic modules for temperature measurement Electronic module, type BL20-1AO- I(0/4...20MA) Electronic module, type BL20-2AO-U (-10/ V) Electronic module, type power distribution modules 24 VDC Electronic module, type BL20-PF- 120/230VAC-D XN-QV/1 XN-QV/2 XN-QV/3 XN-QV/4 XN-QV/5 XN-QV/6 XN-QV/7 XN-QV/8 XN-KO/2 XN-KO/6 XN-KO/8 XN-KO/9 XN-KO/10 XN-KO/11 XN-KO/12 XN-KO/12 XN-KO/13 XN-KO/14 XN-KO/16 XN-KO/ /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

69 Accessories guide Designation Description Type Ident-No. Mechanical accessories End plate mechanical termination of the BL20 station on the right-hand side, included with gateways XN-ABPL End bracket, black mechanical fixing of the BL20 station, 2 pcs., included with gateways XN-WEW-35/2-SW Electrical accessories Shield connection shield connection for direct wiring of BL20 gateway SCH-1-WINBLOC shield connection for analogue signals, 10 pcs. tension clamp screw XN-KLBU/T XN-KLBU/S Ferrite ring Documentation BL20 Manual BL20 Profibus manual BL20 DeviceNet manual for damping high-frequency interference signals to data and supply lines (2 ferrite rings per packing unit) PS416-ZBX Tools Tension clamp operating tool tension clamp operating tool, 5 pcs. XN-ZBW Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 69

70 BL20 product range Digital input modules BL20-2DI-24VDC-P-SS BL20-2DI-120/230VAC BL20-4DI-24VDC-N BL20-2DI-24VDC-N BL20-4DI-24VDC-P BL20-2DI-24VDC-P BL20-16DI-120/230VAC BL20-32DI-24VDC-P BL20-16DI-24VDC-P available planned Digital output modules BL20-2DO-24VDC-2A-N BL20-4DO-24VDC-0.5A-P BL20-2DO-24VDC-0.5A-N BL20-2DO-24VDC-2A-P BL20-2DO-24VDC-0.5A-P BL20-32DO-24VDC-0.5A-P BL20-16DO-24VDC-0.5A-P available planned Analogue input modules BL20-1AI-I(0/4...20MA) BL20-2AI-I(0/4...20MA) BL20-1AI-U( 10/ VDC) BL20-2AI-U(+10/0...10VDC) BL20-4AI-I(0/4...20MA) BL20-2AI-THERMO-PI BL20-2AI-PT/NI-2/3 BL20-1AI-THERMO-PI BL20-1AI-PT100-2/3/4 available planned Analogue output modules Supply modules BL20-2AO-I(0/4...20MA ) BL20-2AO-U( 10/ VDC ) BL20-1AO-I(0/4...20MA ) available planned BL20-BT BL20-PF-120/230VAC-FD BL20-PF-24VDC-FD BL20-PF-120/230VAC-D BL20-PF-24VDC-D BL20-BR-24VDC-D available planned 70 /1102 /0202 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

71 Technology modules BL20-1RS485-INTERFACE BL20-1RS232-INTERFACE BL20-1SSI-INTERFACE BL20-1CNT-24VDC available planned Outlook BL20 offers continuity! With the new I/O concept you are open for future developments. Turck will respond to new market requirements and technologies regarding both fieldbus and I/O functions and implement these in the range of BL20 products. This means long-term security for your investments. Relay modules BL20-2DO-R-CO BL20-2DO-R-NO BL20-2DO-R-NC available planned Gateways BL20-GW-ETHERNET BL20-GW-IBS BL20-GW-CANOPEN BL20-GW-DNET BL20-GW-PBDP-12MB BL20-GW-PBDP-12MB-STD BL20-GW-PBDP-1.5MB-S available BL20-GW-PBDP-1.5MB planned Legend Scheibe Block Gateway available planned Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 71 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 71

72 Notes 72 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

73 Type reference list Type Type Product Ident-No. Page BL20-16DI-24VDC-P digital input module , 64, 65 BL20-16DO-24VDC-0.5A-P digital output module , 64, 65 BL20-1AI-I(0/4...20MA) analogue input module , 64, 65 BL20-1AI-U(-10/ VDC) analogue input module , 64, 65 BL20-1AO-I(0/4...20MA) analogue output module , 64, 65 BL20-1CNT-24VDC counter module , 64, 65 BL20-2AI-PT/NI-2/3 analogue input module , 64, 65 BL20-2AI-THERMO-PI analogue input module , 64, 65 BL20-2AO-U(-10/ VDC) analogue output module , 64, 65 BL20-2DI-120/230VAC-P digital input module , 64, 65 BL20-2DI-24VDC-N digital input module , 64, 65 BL20-2DI-24VDC-P digital input module , 64, 65 BL20-2DO-24VDC-0.5A-N digital output module , 64, 65 BL20-2DO-24VDC-0.5A-P digital output module , 64, 65 BL20-2DO-24VDC-2A-P digital output module , 64, 65 BL20-2DO-R-CO relay module , BL20-2DO-R-NC relay module , 64, 65 BL20-2DO-R-NO relay module , 64, 65 BL20-4DI-24VDC-N digital input module , 64, 65 BL20-4DI-24VDC-P digital input module , 64, 65 BL20-B BL20-B3S-SBB base modulel , 65 BL20-B3S-SBC base module , 65 BL20-B3T-SBB base module , 64 BL20-B3T-SBC base module , 64 BL20-B4S-SBBC base module BL20-B4T-SBBC base module BL20-BR-24VDC-D bus refreshing module , 64, 65 BL20-G BL20-GW-CANOPEN gateway CANopen BL20-GW-DNET gateway DeviceNet BL20-GW-PBDP-1.5MB gateway PROFIBUS-DP BL20-GW-PBDP-1.5MB-S gateway PROFIBUS-DP BL20-GW-PBDP-12MB gateway PROFIBUS-DP BL20-GW-PDB- 12MB-STD gateway PROFIBUS-DP BL20-P BL20-P3S-SBB base module , 30, 65 BL20-P3S-SBB-B base module , 65 BL20-P3T-SBB base module , 30, 64 BL20-P3T-SBB-B base module , 64 BL20-P4S-SBBC base module , 30, 65 BL20-P4S-SBBC-B base module , 65 BL20-P4T-SBBC base module , 30, 64 BL20-P4T-SBBC-B base module , 64 BL20-PF-120/230VAC-D power feeding module , 64, 65 BL20-PF-24VDC-D power feeding module , 64, 65 BL20-S BL20-S3S-SBB base module , 34, 41, 43, 55, 65 BL20-S3S-SBC base module , 65 BL20-S3T-SBB base module , 34, 41, 43, 55, 64 BL20-S3T-SBC base module , 64 BL20-S4S-SBBC base module BL20-S4S-SBBS base module , 43, 56, 61, 65 BL20-S4S-SBBS-CJ base module , 65 BL20-S4S-SBCS base module , 51, 55, 65 BL20-S4T-SBBC base module , 34, 64 BL20-S4T-SBBS base module , 43, 51, 56, 61, 64 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 73

74 Type reference list Type Type Product Ident.-no. Page BL20-S4T-SBBS-CJ base module , 64 BL20-S4T-SBCS base module , 51, 64 BL20-S6S-SBBSBB base module , 65 BL20-S6T-SBBSBB base module , 64 DP DP-busstop monitor adapter cable adapter cable for PROFIBUS DP-BM-M12 adapter M12 to Sub-D for PROFIBUS FW FW5/1-50 labelling plate FW5/ labelling plate FW5/ labelling plate FW5/ labelling plate PS416 PS416-ZBX-405 ferrite ring S SCH-1-WINBLOC shield connection SW-busstop monitor software package for PROFIBUS SW-I/Oassistant Software I/Oassistant XN-A XN-ABPL end plate XN-ANBZ-BL marker XN-ANBZ-BR marker XN-ANBZ-GN marker XN-ANBZ-GN/GE-BED marker XN-ANBZ-RT marker XN-ANBZ-RT/BL-BED marker XN-ANBZ-SW marker XN-ANBZ-WS marker XN-K XN-KLBU/S shield connection XN-KLBU/T shield connection XN-KO/10 slot coding XN-KO/11 slot coding XN-KO/12 slot coding XN-KO/13 slot coding XN-KO/14 slot coding XN-KO/16 slot coding XN-KO/17 slot coding XN-KO/2 slot coding XN-KO/6 slot coding XN-KO/8 slot coding XN-KO/9 slot coding XN-L XN-LABEL/BLOCK label XN-LABEL/SCHEIBE label XN-Q XN-QV/1 relay cross connection link XN-QV/2 relay cross connection link XN-QV/3 relay cross connection link XN-QV/4 relay cross connection link XN-QV/5 relay cross connection link XN-QV/8 relay cross connection link XN-W/-Z XN-WEW-35/2-SW end bracket XN-ZBW2 tension clamp operating tool /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

75 Type reference list Ident-No. Ident-no. Type Product Page BL20-GW-PBDP-1.5MB gateway PROFIBUS-DP BL20-GW-PBDP-1.5MB-S gateway PROFIBUS-DP BL20-GW-PBDP-12MB gateway PROFIBUS-DP BL20-GW-PBDP-12MB-STD gateway PROFIBUS-DP BL20-GW-CANOPEN gateway CANopen BL20-GW-DNET gateway DeviceNet TM BL20-BR-24VDC-D bus refreshing module 29, 64, BL20-PF-24VDC-D power feeding module 30, 64, BL20-PF-120/230VAC-D power feeding modulel 30, 64, BL20-2DI-24VDC-P digital input module 32, 64, BL20-2DI-24VDC-N digital input module 32, 64, BL20-2DI-120/230VAC-P digital input module 34, 64, BL20-4DI-24VDC-P digital input module 36, 64, BL20-4DI-24VDC-N digital input module 36, 64, BL20-16DI-24VDC-P digital input module 34, 64, BL20-2AI-PT/NI-2/3 analogue input module 43, 64, BL20-1AI-I(0/4...20MA) analogue input module 41, 64, BL20-1AI-U(-10/ VDC) analogue input module 41, 64, BL20-2AI-THERMO-PI analogue input module 47, 64, BL20-2DO-24VDC-0.5A-P digital output module 49, 64, BL20-2DO-24VDC-0.5A-N digital output module 49, 64, BL20-2DO-24VDC-2A-P digital output module 49, 64, BL20-16DO-24VDC-0.5A-P digital output modulel 50, 64, BL20-2DO-R-NC relay module 56, 64, BL20-2DO-R-NO relay module 56, 64, BL20-2DO-R-CO relay module 56, 64, BL20-1CNT-24VDC counter module 61, 64, BL20-1AO-I(0/4...20MA) analogue output module 54, 64, BL20-2AO-U(-10/ VDC) analogue output modulel 55, 64, BL20-P3T-SBB base module 29, 30, BL20-P3S-SBB base module 29, 30, BL20-P4T-SBBC base module 29, 30, BL20-P4S-SBBC base module 29, 30, BL20-P3T-SBB-B base module 29, BL20-P4T-SBBC-B base module 29, BL20-P3S-SBB-B base module 29, BL20-P4S-SBBC-B base module 29, BL20-S3T-SBB base module 32, 34, 41, 43, 55, BL20-S3S-SBB base module 32, 34, 41, 43, 55, BL20-S4T-SBBS base module 41, 43, 56, 61, BL20-S4S-SBBS base module 41, 43, 56, 61, BL20-S4T-SBBS-CJ base module 47, BL20-S4S-SBBS-CJ base module 47, BL20-S4T-SBBC base module 32, 34, BL20-S4S-SBBC base module 32, 34, BL20-S6T-SBBSBB base module 36, BL20-S6S-SBBSBB base module 36, BL20-B3T-SBB base module 38, BL20-B3S-SBB base module 38, BL20-B4T-SBBC base module BL20-B4S-SBBC base module BL20-S3T-SBC base module 49, BL20-S3S-SBC base module 49, BL20-S4S-SBCS base module 49, 56, BL20-B3S-SBC base module 50, BL20-S4T-SBCS base module 49, 56, XN-LABEL/SCHEIBE label XN-LABEL/BLOCK label XN-ANBZ-BL marker 68 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 75

76 Type reference list Ident-No. Ident-No. Type Product Page XN-ANBZ-RT marker XN-ANBZ-GN marker XN-ANBZ-SW marker XN-ANBZ-BR marker XN-ANBZ-RT/BL-BED marker XN-ANBZ-GN/GE-BED marker XN-ANBZ-WS marker PS416-ZBX-405 ferrite ring FW5/1-50 slot coding FW5/ slot coding FW5/ slot coding FW5/ slot coding XN-QV/1 relay cross connection link XN-QV/2 relay cross connection link XN-QV/3 relay cross connection link XN-QV/4 relay cross connection link XN-QV/5 relay cross connection link XN-QV/6 relay cross connection link XN-QV/7 relay cross connection link XN-QV/8 relay cross connection link XN-KO/2 slot coding XN-KO/6 slot coding XN-KO/8 slot coding XN-KO/9 slot coding XN-KO/10 slot coding XN-KO/11 slot coding XN-KO/12 slot coding XN-KO/13 slot coding XN-KO/14 slot coding XN-KO/16 slot coding XN-KO/17 slot coding XN-ABPL end plate XN-WEW-35/2-SW end bracket XN-KLBU/T shield connection XN-KLBU/S shield connection XN-ZBW2 tension clamp operating tool SW-busstop monitor software package for PROFIBUS SW-I/Oassistant software I/Oassistant DP-BM-M12 adapter M12 to Sub-D for PROFIBUS DP-busstop monitor adapter cable adapter cable for PROFIBUS /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

77 Notes Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 77

78 Notes 78 /1102 Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de

79 Bitte senden Sie mir Unterlagen: Sensortechnik Induktive Sensoren Induktive Sensoren für Schwenkantriebe uprox induktive Sensoren Kapazitive Sensoren Magnetfeldsensoren Opto-Sensoren Geräte für den Personenschutz Ultraschall-Sensoren levelprox-füllstandssensoren Strömungswächter Druckwächter Temperaturwächter Identifikationssytem Linearweg-Sensoren Drehweg-Sensoren Steckverbinder CD-ROM Sensortechnik Interfacetechnik Interfacetechnik im Aufbaugehäuse Bauform multimodul Bauform multisafe Allgemeine Informationen Interfacetechnik auf 19"-Karte Bauform multicart Miniaturrelais, Industrierelais, Zeitwürfel, Sockel Zeit- und Überwachungsrelais Ex-Schutz Grundlagen für die Praxis (Übersichtsposter) CD-ROM Interfacetechnik Feldbustechnik busstop -Feldbuskomponenten Bussystem sensoplex 2 Bussystem sensoplex 2Ex Bussystem sensoplex MC Bussystem AS-Interface Bussystem DeviceNet Ethernet Netzwerkkomponenten BL20 I/O-Busklemmensystem Bussystem FOUNDATION fieldbus Bussystem PROFIBUS-DP Bussystem PROFIBUS-PA Bussystem piconet Bussystem excom FAX-ANTWORT/FAX REPLY Absender/Sender: Firma/Company: Abt./Position: Adresse/Address: Please send me more information: Sensors inductive sensors inductive sensors for rotary actuators uprox inductive sensors capacitive sensors magnetic-field sensors photoelectric sensors machine safety equipment ultrasonic sensors levelprox level sensors flow controls pressure controls temperature controls identification system linear position sensors rotary position sensors connectors CD-ROM Sensors Interface technology devices in modular housings multimodul style multisafe style general information devices on 19" card multicart style miniature relays, industrial relays, time cubes, sockets programmable relays and timers explosion protection basics for practical application (overview poster) CD-ROM Interface technology Fieldbus technology busstop fieldbus components bus system sensoplex 2 bus system sensoplex 2Ex bus system sensoplex MC bus system AS-Interface bus system DeviceNet Ethernet network components BL20 I/O bus terminal system bus system FOUNDATION fieldbus bus system PROFIBUS-DP bus system PROFIBUS-PA bus system piconet bus system excom Hans Turck GmbH & Co. KG D Mülheim an der Ruhr Phone (+49) (2 08) Fax (+49) (2 08) turckmh@mail.turck-globe.de Tel./Phone: Fax: Internet Hans Turck GmbH & Co.KG D Mülheim an der Ruhr Tel. 0208/ Fax 0208/ turckmh@mail.turck-globe.de / 79