Note: Indented items indicate parts included in an assembly listed above

Transcription

1 Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number QTY DirectCommand Kit Installation Instructions DC Motor Driver Liquid Product Control Module Cable Power, Multiple Module 12ft Cable Flow Meter/Motor Driver 6ft Cable 12V PWM Motor Power 6ft Cable 10 Boom Motor Valves, Raven, 6ft Cable High Current Adapter CAN Y-Splice CAN BUS Stub 8in Cable CAN BUS Line 8in Cable Implement Plug Implement Switch Tee 1 Input Mounting Kit Large Module Mounting Plate WP Plugged Shroud 3-pin Generic Cable Installation Kit Hardware Kit Large Module This DirectCommand Kit also requires the installation of a Display Kit or Display Cable Kit and 10-Boom Switch Box Kit for correct operation. 10-Boom Switch Box Kit (Ordered Separately) QTY Hardware Kit Deutsch Dust Plug 6-pin CAN Y-Splice CAN Bus Stub 1 ft Switch Box Bracket Switch Box Console Auxiliary Input Module PN: Rev. A October 2011 Page 1 of 11

2 DirectCommand Installation Important Notices You will save time and prevent wrong installation of components by closely following these step-by-step instructions. If you have questions, call Ag Leader Technology at Ext 1. Direction words (LEFT and RIGHT) are commonly used when describing an installation procedure. Interpret direction words as if standing behind equipment and looking forward Signal words (CAUTION, IMPORTANT and NOTE) are provided to draw attention to information that is important for the safe/correct installation and operation of this product. CAUTION will alert you to situations that will impact the physical safety of you or others. IMPORTANT will alert you to the potential for damage to the product or loss of data. NOTE will provide you with additional information to simplify a procedure or clarify a process. Read all instructions first to familiarize yourself with the installation procedures. Keep parts list and installation instructions for use as a reference after completing installation. This DirectCommand Kit fits planters with the Raven Crop Start fertilizer delivery system. Section Contents Section Heading Page Common Components 3 System Layout 4-5 Safety Notices 6 Installing the Liquid Control Module and DC Motor Driver 7 Installing the Module Power and CAN Cables 7 Installing the Control and Flow Meter Cables 9 Setting Up the Display 11 Page 2 of 11 October 2011 PN: Rev. A

3 Common Components This section contains illustrations of components common to all Direct Command Installations. Their purpose is to ensure proper identification and installations in the sections that follow. CAN BUS Connectors 1. Terminator PN: Plug (Not all applications) PN: Y-Splice PN: Auxiliary Input Module 2. Liquid Product Control Module DC Motor Driver PN: Rev. A October 2011 Page 3 of 11

4 DirectCommand Installation System Layout Page 4 of 11 October 2011 PN: Rev. A

5 System Layout PN: Rev. A October 2011 Page 5 of 11

6 DirectCommand Installation Safety Notices CAUTION: Hydraulic equipment should be on safety stops, hydraulic pressure relieved with machines systems turned off and all machine motion stopped before starting work. CAUTION: Be sure to wear proper eye protection when using any power tools, such as when drilling any mounting holes. IMPORTANT: Check behind vehicle and implement panels for any holes, wiring or controls that could be damaged when drilling any holes. IMPORTANT: Disconnect the Display, DirectCommand components and any sensors from electrical system when welding on equipment or jump starting unit to prevent component damage due to power surges or excessive current. IMPORTANT: If using a non Ag Leader GPS receiver, make sure to install a Null Modem Cable, included in the Display Kit, to prevent damage to the Display or GPS receiver. IMPORTANT: Use Dielectric grease to coat the seals and terminals of each connector that will be exposed to weather or chemicals as you plug them in. NOTE: Be sure to follow the alignment keys on the plugs and the receptacles carefully. Do not use excessive force when mating connectors. Page 6 of 11 October 2011 PN: Rev. A

7 Installing the Liquid Control Module and DC Motor Driver Parts required for procedure: From DirectCommand Kit: (1) Hardware Kit Large Module PN: (1) Mounting Kit Large Module Plate PN: (1) DC Motor Driver PN: (1) Liquid Control Module PN: Step-by-Step instructions for installing the Liquid Control Module and DC Motor Driver 1. The Liquid Control Module may be mounted at the operator s discretion. Make sure the module is mounted in a location where the control cables will reach. 2. If mounting the Liquid Control Module on an existing plate, using the module as a template, drill 1/4" diameter holes in the plate. Use 1/4" stainless steel hardware provided in the Hardware Kit PN: to secure the module into place. 3. If mounting the Liquid Control Module on a toolbar, the Large Module Mounting Kit PN: may be used for toolbars up to a 6 x6 square tube. 4. The DC Motor Driver may be mounted at the operator s discretion. Make sure the Driver is mounted in a location where the control and power cables will reach near the Liquid Control Module. Installing the Module Power and CAN Cables Parts required for procedure: From DirectCommand Kit: (1) CAN Bus Stub 8in. PN: (1) Cable High Current Adapter PN: (1) Generic Cable Installation Kit PN: (1) Cable Power, Multiple Module 12ft. PN: Optional items included in the kit: (1) CAN Y-Splice PN: (1) Cable CAN BUS Line 8in. PN: Purchased Separately: (1) Implement Cable 12ft. PN: (1) CAN/Power Cable 3ft. PN: PN: Rev. A October 2011 Page 7 of 11

8 DirectCommand Installation Step-by-Step instructions for installing the Module Power and CAN Cables 1. Connect the ring terminals on the Multiple Module Power Cable, PN: to the battery, or power studs in the cab. Connect the ring terminal with fuses to the positive terminal and connect the ring terminal with black wires to the battery ground. 2. Route the opposite end of the cable toward the CAN/Power Cable, PN: Connect the black 2-pin Deutsch plug on Multiple Module Power Cable to the mating black 2-pin Deutsch secondary receptacle on the CAN/Power Cable. 4. Connect the 4-pin gray Deutsch plug on the 8 in CAN Bus Stub, PN: into the receptacle labeled CAN BUS on the Liquid Control Module. 5. Connect the opposite end of the CAN Bus Stub into the gray side of the CAN Y-Splice installed on the Implement Cable, PN: Locate the High Current Adapter Cable, PN: in the 7. Connect the gray 2-pin Deutsch receptacle on the High Current Adapter Cable to the mating black 2-pin Deutsch secondary plug on the Implement Cable, PN: Connect one of the gray 2-pin power plugs on the High Current Adapter Cable into the 2-pin receptacle coming out of the Liquid Control Module. 9. Connect one of the gray 2-pin power plugs on the High Current Adapter Cable into the mating 2-pin receptacle on the DC Motor Driver. Note: An additional CAN Y-Splice, PN: and CAN Extension Cable, PN: are included in the kit to connect the Liquid Product Control Module to the CAN BUS in multiple module configurations. Page 8 of 11 October 2011 PN: Rev. A

9 Installing the Control and Flow Meter Cables Parts required for procedure: From DirectCommand Kit: (1) Cable Flow Meter/DC Motor Driver 6ft. PN: (1) Cable 12V PWM Motor Power 6ft. PN: (1) Cable 10 Boom Motor Valves 6ft. PN: (1) Generic Cable Installation Kit PN: (9 included) WP Plugged Shroud 3-pin PN: (1) Cable Implement Plug PN: Optional item included in the kit: (1) Implement Switch Tee 1 Input PN: Step-by-Step instructions for installing the Control and Flow Meter Cables 1. Locate the Implement Plug Cable, PN: in the 2. Connect the black 12-pin Deutsch plug from the Implement Plug Cable to the mating black 12-pin receptacle on the Liquid Control Module labeled AUXILIARY. 3. Locate the Flow Meter/DC Motor Driver Cable, PN: , in the 4. Connect the gray 8-pin Deutsch plug from the above cable into the mating receptacle on the Liquid Control Module labeled CHANNEL Connect the black 2-pin Deutsch plug from the Flow Meter/DC Motor Driver Cable to the mating black receptacle on the DC Motor Driver. 6. Route the opposite end of the cable toward the product flow meter. 7. Disconnect the existing Raven flow meter cable at the Conxall connectors. 8. Connect the 3-pin Conxall plug from the Flow Meter/DC Motor Driver Cable to the mating connector on the flow meter. 9. Locate the 12V PWM Motor Cable PN: in the 10. Connect the gray 2-pin Deutsch receptacle from the 12V PWM Motor Cable to the mating 2-pin Deutsch plug on the DC Motor Driver. PN: Rev. A October 2011 Page 9 of 11

10 DirectCommand Installation 11. Route the opposite end of the 12V PWM Motor Cable toward the Crop Start fertilizer pump. 12. Disconnect the existing Raven Crop Start Pump cable at the Weatherpack connectors. 13. Connect the 2-pin Weatherpack tower to the mating 2-pin shroud on the Crop Start fertilizer pump. 14. Locate the 10 Boom Motor Valve Cable, PN: in the 15. Connect the gray 12-pin Deutsch plug from the Boom Motor Valve Cable to the mating receptacle labeled BOOM on the Liquid Control Module. 16. Connect the gray 2-pin Deutsch receptacle on the Boom Motor Valve Cable to a gray 2-pin power plug on the High Current Adapter Cable, PN: Route the opposite end of the cable toward the boom section valve(s). 18. Disconnect the existing Boom Valve Cable(s) at the Weatherpack connections. 19. Connect the 3-pin Weatherpack tower from the 10 Boom Motor Valve Cable to the 3-pin Weatherpack shroud on the section valve assembly. 20. Repeat step 19 for each additional boom section in your configuration. 21. Install WP Plugged Shrouds, PN: on any unused boom section tower connectors. These dust covers are included in the 22. Bundle cables and secure them as necessary with zip-ties from Cable Installation Kit, PN: Note: An Implement Switch Tee Cable, PN: is included in the kit for connection to an existing implement switch, if applicable. Page 10 of 11 October 2011 PN: Rev. A

11 Setting up the Display 1. Refer to the control chart below for setting up the Display. 12V DC Motor PWM Configuration Setting Name Default Value Description Control Configuration PWM 12 Volt Rate Control is achieved through speed changes of the Crop Start fertilizer pump. The PWM signal is sent from the LCM to the DC Motor Driver and then to the Crop Start Fertilizer Pump. PWM Frequency 100 This setting is the frequency that the 12V fertilizer pump is pulsed at. Gain* Allowable Error 2% This setting determines how aggressively the fertilizer pump responds when making rate change adjustments. The higher the value, the more aggressive the system response is. Note: Leaving all other control settings at the default value and making small adjustments to the Gain is usually all that is required to fine-tune the control system. Determines the percent of error that is allowed prior to the product control system making any flow rate corrections. Too low of a setting will cause the control system to continually hunt for the target application rate. Too high of a setting will cause excessive application error. Zero Flow offset 5 This setting represents the maximum duty cycle that is sent to the fertilizer pump without producing product flow. Using too high of a Zero Flow Offset value can cause the product delivery system to not properly shut off. Flow Meter Cal* *See Flow Meter This is the pulses per gallon through the flow meter. Note: Raven flow meter calibration numbers are in pulses per 10 gallons of product flow. To calculate the appropriate values, divide the Raven calibration number by 10 before entering into the Ag Leader Display. PN: Rev. A October 2011 Page 11 of 11