Product Specification

Size: px

Start display at page:

Download "Product Specification"

Georgiana McDonald
6 years ago
Views:

1 To : REV A Product Specification Customer : Model NO. :HD-1024G600-70MTW Sample No. : Production Designed by Checked by Approved by DEPT. Final Approval by Customer OK NG Problem survey: Approved By Hyundai LCD (HK) Co., Ltd. MODEL HD-1024G600-70MTW 1 Product Specifications

2 Record of Revision Version Contents Date Note A. New issued 2011/03/02 MODEL 2 Product Specifications HD-1024G600-70MTW

3 Contents NO. CONTENTS PAGE REVISION STATUS... 1 TABLE OF CONTENTS GENERAL DESCRIPTION MECHANICAL SPECIFICATION PIN DESCRIPTION ELECTRICAL CHARACTERISTICS INPUT SIGNAL CHARACTERISTICS OPTICAL CHARACTERISTICS QUALITY ASSURANCE SYSTEM GENERAL PRECAUTION MODEL HD-1024G600-70MTW 3 Product Specifications

4 1. GENERAL DESCRIPTION 1.1 DESCRIPTION The specifications is a color active matrix TFT LCD module using amorphous silicontft's (Thin Film Transistors) as an active switching devices.. This product is composed of a TFT LCD panel, driver ICs and a backlight unit. The following table described the features of 7DW WSVGA. 1.2 FEATURES: No. Item Specification Unit 1 Panel Size 7 inch 2 Number of Pixels (RGB) 600 pixels 3 Active Area 153.6(H) 90(V) mm 4 Pixel Pitch 0.050(H) 0.150(V) mm 5 Outline Dimension (H) (V) 2.35(D) mm 6 Number of Colors 16.7M - 7 Display Mode Transmission mode, Normally Black - 8 Viewing Direction Pixels RGB stripe arrangement - 9 Pixel Arrangement RGB-Stripe - 10 Luminance (cd/m^2) 400(TYP) nit 11 Contrast Ratio 400(TYP) 12 Surface Treatment Hard Coating, 3H, Low Reflection (Front Polarizer) 13 Interface LVDS - 14 Backlight LED - 15 Driver IC Operation Temperature -20~70 17 Storage Temperature -30~80 18 Weight - g - MODEL HD-1024G600-70MTW 4 Product Specifications

5 2. MECHANICAL SPECIFICATION MODEL HD-1024G600-70MTW 5 Product Specifications

6 MODEL HD-1024G600-70MTW 6 Product Specifications

7 3. PIN DESCRIPTION Pin No. Symbol Function Remark 1 VDDIN Power supply VDDIN=3.7V (Typ.) 2 VDDIN Power supply VDDIN=3.7V (Typ.) 3 VDDIN Power supply VDDIN=3.7V (Typ.) 4 VDDIN Power supply VDDIN=3.7V (Typ.) 5 VDDIN Power supply VDDIN=3.7V (Typ.) 6 VDDIN Power supply VDDIN=3.7V (Typ.) 7 VDDIN Power supply VDDIN=3.7V (Typ.) 8 NC Non Connection 9 NC Non Connection 10 LDO_EN LDO enable for driver IC 11 GND GROUND 12 GND GROUND 13 RIN0- LVDS Negative data signal (-) 14 RIN0+ LVDS Positive data signal (+) 15 GND GROUND 16 RIN01- LVDS Negative data signal (-) 17 RIN01+ LVDS Positive data signal (+) 18 GND GROUND 19 RIN02- LVDS Negative data signal (-) 20 RIN02+ LVDS Positive data signal (+) 21 GND GROUND 22 LVDS_CLK- LVDS Negative CLK signal (-) 23 LVDS_CLK+ LVDS Positive CLK signal (+) 24 GND GROUND 25 RIN3- LVDS Negative data signal (-) 26 RIN3+ LVDS Positive data signal (+) MODEL HD-1024G600-70MTW 7 Product Specifications

8 27 GND GROUND 28 LED_EN LED enable 29 GND GROUND 30 DVDD 3.3V Power 31 GND GROUND MODEL HD-1024G600-70MTW 8 Product Specifications

9 4. ELECTRICAL CHARACTERISTICS 4.1 ABSOLUTE MAXIMUM RATINGS Item Symbol Ta=25±2 Min. Values Max Power Supply Voltage VDD V Back-light Power Supply Voltage Unit HVDD V Back-light LED Current ILED - 30 ma Remark Back-light LED Reverse VR - 2 V Voltage Note1: The absolute maximum rating values of this product are not allowed to be exceeded at any times. Should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme case, the module may be permanently destroyed. 4.2TFT LCD MODULE Ta=25±2 Item Symbol Values Min. Typ. Max. Power Supply Input Voltage VDD V Unit Power Supply Current IDD ma Back-light Power Supply Voltage Back-light Power Supply Current HVDD V IHVDD ma LED Driver Efficiency η % Positive-going Input Threshold Voltage Negative-going InputThreshold Voltage Differential input common mode voltage Power Consumption VIT mv VIT mv Vcom V Remark Note1 Note2 Vcom = 1.2Vtyp. VIH=100mV, VIL=100mV PD W Note1 PBL 1.25 W Note2 PTotal 2.01 W Note1: The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.7V at 25 Typ : Black Pattern Note2: Calculated value for reference (VLED X ILED) MODEL 9 Product Specifications HD-1024G600-70MTW

10 4.3 POWER SEQUENCE Parameter Values Min. Min. Max T ms T ms T ms T ms T ms T ms T ms Note1:When the power supply VDD is 0V, keep the level of input signals onthe low or keep high impedance. Note2:Do not keep the interface signal high impedance when power is on. Back Light must be turn on after power for logic and interface signalare valid. Unit MODEL HD-1024G600-70MTW 10 Product Specifications

11 4.4 BACK LIGHT Item Symbol Values Min. Typ. Max. Unit Remark LED Forward Voltage VF V - LED Forward Current IF ma - LED Power Consumption PLED W Note 1 LED Life-Time N/A 15,000 Hour Power supply voltage for LED Driver EN Control Level PWMControlLevel VLED V Backlight on mv Backlight off mv PWM High Level PWM Low Level V V PWM Control Frequency FPWM KHz Duty Ratio - 90% 93% - % IF = 20mA Note 2 Note1: Calculator Value for reference ILED VLED = PLED Note2: The LED Life-time define as the estimated time to 50% degradation of initialluminous. MODEL HD-1024G600-70MTW 11 Product Specifications

12 5. INPUT SIGNAL CHARACTERISTICS 5.1 OPERATED BY THE DE ONLY Parameter Symbol Min. Typ. Max. Unit Frequency 1/Tc MHz Clock High Time Tch 40% 50% 60% Tc Low Time Tcl 60% 50% 40% Tc lines Frame Period Tv Hz ms Vertical Display Period Tvd lines One line ScanningPeriod Th clocks Horizontal DisplayPeriod Thd clocks LVDS Rx Interface Timing Parameter Parameter Symbol Min. Typ. Max. Unit Remark CLKIN Period trcip nsec Input Data 0 trip nsec Input Data 1 trip0 tricp/7-0.4 tricp/7 tricp/7+0.4 nsec Input Data 2 trip7 2 tricp/ tricp/7 2 tricp/7+0.4 nsec Input Data 3 trip6 3 tricp/ tricp/7 3 tricp/7+0.4 nsec Input Data 4 trip5 4 tricp/ tricp/7 4 tricp/7+0.4 nsec Input Data 5 trip4 5 tricp/ tricp/7 5 tricp/7+0.4 nsec Input Data 6 trip3 6 tricp/ tricp/7 6 tricp/7+0.4 nsec Input Data 7 trip2 7 tricp/ tricp/7 7 tricp/7+0.4 nsec MODEL HD-1024G600-70MTW 12 Product Specifications

13 5.2 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL MODEL HD-1024G600-70MTW 13 Product Specifications

14 5.3 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS MODEL HD-1024G600-70MTW 14 Product Specifications

15 5.4. LVDS INTERFACE 5.5LVDS INPUT SIGNAL 5.6 DATA INPUT FORMAT MODEL HD-1024G600-70MTW 15 Product Specifications

16 6. OPTICAL CHARACTERISTICS Item Symbol Condition Contrast Ratio Luminance of White(9 Points) WhiteLuminance uniformity(9 Points) Response Time (Rising + Falling) Chromaticity Viewing Angle Red Green Blue White Hor. Ver. CR Values Min. Typ. Max. Unit Remark Note2 Yw Θ = cd/m2 Note3 ΔY Note4 TRT Rx Ta=25 Θ = ms Note6 TBD TBD TBD - Ry TBD TBD TBD - Gx TBD TBD TBD - Gy TBD TBD TBD - Θ = 0 Bx TBD TBD TBD - By TBD TBD TBD - Wx TBD TBD TBD Wy TBD TBD TBD Θ Θ CR > 10 Θ Θ Note1:Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o clock direction and the vertical or 6, 12 o clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE 1). Note2: Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (see FIGURE 1) Luminance Contrast Ratio (CR) is defined mathematically. deg. Note5 Note1 Note3: Center Luminance of white is defined as luminance values of 9 pointaverage across the LCDsurface. Luminance shall be measured with allpixels in the view field set first to white. This measurement shall be taken atthe locations shown in FIGURE 2 for a total of the measurements per display.the LED current is setting at 20mA. MODEL HD-1024G600-70MTW 16 Product Specifications

17 Note4: The White luminance uniformity on LCD surface is then expressed as : ΔY = Minimum Luminance of 9 points / Maximum Luminance of 9 points (seefigure 2). Note5:The color chromaticity coordinates specified in Table 5 shall be calculatedfrom the spectral data measured with all pixels first in red, green, blue andwhite. Measurements shall be made at the center of the panel. Note5: The color chromaticity coordinates specified in Table 5 shall be calculatedfrom the spectral data measured with all pixels first in red, green, blue andwhite. Measurements shall be made at the center of the panel. Note6: The electro-optical response time measurements shall be made as FIGURE3 by switching the data input signal ON and OFF. The times needed for theluminance to change from 10% to 90% is Tr, and 90% to 10% is Td. Note7: Cross-Talk of one area of the LCD surface by another shall be measured bycomparing the luminance (YA) of a 25mm diameter area, with all displaypixels set to a gray level, to the luminance (YB) of that same area when anyadjacent area is driven dark. (See FIGURE 4). Figure1 Measurement Set Up Figure2 White Luminance and Uniformity Measurement Locations (9 points) Center Luminance of white is defined as luminance values of center 9 pointsacross the LCD surface. Luminance shall be measured with all pixels in the viewfield set first to white. This measurement shall be taken at the locations shown infigure 2 for a total of the measurements per display.the White luminance uniformity on LCD surface is then expressed as : ΔY9 = Minimum Luminance of five points / Maximum Luminance of nine points (see FIGURE 2). MODEL HD-1024G600-70MTW 17 Product Specifications

18 Figure3 Response Time Testing The electro-optical response time measurements shall be made as shown infigure 3 by switching the data input signal ON and OFF. The times neededfor the luminance to change from 10% to 90% is Tr and 90% to 10% is Td. Figure4Cross Modulation Test Description The location measured will be exactly the same in both patternscross-talk of one area of the LCD surface by another shall be measured bycomparing the luminance (YA) of a 25mm diameter area, with all display pixelsset to a gray level, to the luminance (YB) of that same area when any adjacentarea is driven dark (Refer to FIGURE 4). MODEL HD-1024G600-70MTW 18 Product Specifications

19 7. QUALITY ASSURANCE SYSTEM 7.1 TEMPERATURE AND HUMIDITY Test Item HighTemperatureStorage Low Temperature Storage High Temperature Operation LowTemperatureOperation HighTemperatureHighHumidity Operation Thermal Shock Test Condition Ta=80 ; 240hrs Ta=-30 ; 240hrs Ta=70,240Hrs Ta=-20 ; 240hrs Ta=60,90%RH,240Hrs(no condensation) -20 (0.5h) ~ 70 (0.5h) / 100cycles 7.2 VIBRATION & SHOCK Test item 7.3 ESD Packing Shock (non-operation) Packing Vibration (non-operation) Test item Electro Static Discharge Test (non-operation) Conditions 980m/s2,6ms, ±x,y,x 3times for direction Frequency range:10 HZ~55HZ Stroke:1.5mm,sweep:10 HZ ~55 HZ x,y,x2 hours for each direction Conditions ±200v,200pF, 0Ω MODEL HD-1024G600-70MTW 19 Product Specifications

20 8. GENERAL PRECAUTION 8.1 SAFETY (1) Do not swallow any liquid crystal, even if there is no proof that liquid crystal ispoisonous. (2) If the LCD panel breaks, be careful not to get liquid crystal to touch your skin. (3) If skin is exposed to liquid crystal, wash the area thoroughly with alcohol or soap. 8.2 STORAGE CONDITIONS (1) Store the panel or module in a dark place where the temperature is 23±5 C andthe humidity is below 50±20%RH. (2) Store in anti-static electricity container. (3) Store in clean environment, free from dust, active gas, and solvent. (4)Do not place the module near organics solvents or corrosive gases. (5) Do not crush, shake, or jolt the module. 8.3 HANDLING PRECAUTIONS (1) Avoid static electricity which can damage the CMOS LSI. (2) The polarizing plate of the display is very fragile. So, please handle it verycarefully. (3) Do not give external shock. (4) Do not apply excessive force on the surface. (5) Do not wipe the polarizing plate with a dry cloth, as it may easily scratch thesurface of plate. (6) Do not use ketonics solvent & Aromatic solvent, use with a soft cloth soaked with a cleaning naphtha solvent. (7) Do not operate it above the absolute maximum rating. (8) Do not remove the panel or frame from the module. (9)When the module is assembled, it should be attached to the system firmly,be careful not to twist and bend the module. (10)Wipe off water droplets or oil immediately. If you leave the droplets for a longtime, staining and discoloration may occur. (11) If the liquid crystal material leaks from the panel,it should be kept away from theeyes or mouth.in case of contact with hands,legs or clothes, it must be washedaway thoroughly with soap. 8.4 WARRANTY (1)The period is within twelve months since the date of shipping out under normal using and storage conditions. (2) Do not repaired or modified the LCM. It may cause function to lose efficacy,hyundai LCD does not warrant the LCM. (3) All process and material comply ROHS. MODEL HD-1024G600-70MTW 20 Product Specifications

SPECIFICATION FOR LCD MODULE

SPECIFICATION FOR LCD MODULE MODULE NO: VERSION NO.: V1.1 Customer s Approval: PREPARED BY CHECKED BY APPROVED BY SIGNATURE DATE Orient Display (NA) Ltd. 145 Royal Crest Court Unit 42, Markham ON L3R9Z4