Contents. External Pinsetter Interface Box... 1

Transcription

1 Contents External Pinsetter Interface Box... 1 Internal Pinsetter Interface Box (Non- GS Series Pinsetters, Earlier GS Series Pinsetter Installations)... 3 Pinsetter Controller PCB... 4 Adaptor PCB... 7 GS Series Pinsetter Controller... 9 GS Series Pinsetter Setup PCB Replacement Setup Pinsetter Controller PCB Configuration Jumpers (JP1, JP2, and JP3) Termination Jumper (JP4) S1- ID Switch GS Controller PCB Termination Jumper (J8) Cable Diagrams Pinsetter Interface 29 i

2 ii 30 Pinsetter Interface Intentionally Blank

3 External Pinsetter Interface Box The main purpose of the Pinsetter Interface Box is to connect a scanner, pinsensor, or non-direct Connect GS-Series pinsetter and selected pinsetter signals to the Lane Group Processor (LGP) of a lane pair. The box provides control for the pinsetter to allow the LGP to turn the machine on and off automatically, reset the machine when needed, and obtain pinsetter cycle count information. The box also routes 28 VAC to power the scanner or pinsensor and allows them to communicate properly with the LGP. When connected to a Brunswick GS Series pinsetter, the box adapts the communication from the Gamesetter or Consolidated Low Voltage Box. so it can be understood by the LGP. With installations that include BowlerTrack, the Pinsetter Interface Box connects the BowlerTrack PCB to the LGP. Two interface boxes are currently available. The first is used for non-gs- Series pinsetters and in earlier GS-Series pinsetter installations. The second is used for later GS-Series pinsetter installations. The Interface Box is typically located on a mounting board attached to the curtain wall or between a pair of pinsetters. Refer to the figure titled External Pinsetter Interface Box. External Pinsetter Interface Box (1) KEYSWITCH (2) DIAGNOSTICS LIGHT (3) MECHANIC OVERRIDE SWITCH (4) CURTAIN WALL (5) MOUNTING BOARD (6) LATER GS SERIES PINSETTER INSTALLATIONS (7) NON GS SERIES PINSETTER INSTALLATIONS, EARLIER GS SERIES PINSETTER INSTALLATIONS Pinsetter Interface 1

4 The function of the components in the Pinsetter Interface Box are: (1) Diagnostics LED - This light flashes to indicate the operation condition and setup of the Pinsetter Controller PCB. In older units, this LED is located on the Pinsetter Controller PCB. On newer interface boxes for GS Series pinsetters, this LED is removed. Flash Slow Rate Medium Fast Switch 8 position Meaning of S1 is set to the "ON" Switch 8 of S1 is set to the "OFF" position and communication to the scanner or pinsensor has been established. Switch 8 of S1 is set to the "OFF" position, but communication to the scanner or pinsensor has not been established. (2) Keyswitch - The keyswitch is present on some interface boxes. If present, the switch should be disconnected from the Pinsetter Controller PCB. (3) Mechanic Override Switch - This switch allows the user to turn the pinsetter on and off manually in the event of a failure in the system or the Pinsetter Interface Box. When set to the scorer control position, the LGP will control the on/off operation of each pinsetter. When set to the mechanic override position, both pinsetters will turn on. On newer interface boxes for GS Series pinsetters, this switch has been removed. 2 Pinsetter Interface

5 Internal Pinsetter Interface Box (Non- GS and Earlier GS Series Pinsetter Installations) Internally, the Pinsetter Interface Box consists of one main circuit board called the Pinsetter Controller PCB and a main power transformer. When the box is connected to a Brunswick GS Series pinsetter or the BowlerTrack option is installed, an additional board called the Adaptor PCB is added to the box. Refer to the figure titled Internal Pinsetter Interface Box. Internal Pinsetter Interface Box The functions of the components in the Pinsetter Interface Box are: (1) Adaptor PCB - This board adapts the communication from the Gamesetter of a GS Series pinsetter or BowlerTrack PCB so it can be used by the LGP. It is only installed in the Pinsetter Interface Box if a Brunswick GS-10, GS-92, or GS-96 Pinsetter is being used or if the BowlerTrack option is installed. For installations after January 2000, this PCB is located in the BowlerTrack chassis. (2) Pinsetter Controller PCB - This board is responsible for all of the functions provided by the interface box. (3) Power Transformer - The transformer changes the incoming 28 VAC received from the Secondard Console (Laneworx, Powerworx, Touchworx) or LGP chassis (Skyworx and Teamworx) to 9.5 VAC. This voltage is sthen used by the Pinsetter Controller PC to generate 5 VDC. Pinsetter Interface 3

6 Pinsetter Controller PCB The Pinsetter Controller PCB is responsible for all of the functions provided by the Pinsetter Interface Box. It allows the control of the pinsetter so the LGP can turn the machine on/off automatically and obtain pinsetter cycle count information. The board also routes 28 VAC to power the scanner or pinsensor and allows them to communicate properly with the LGP. Refer to the figure titled Pinsetter Controller PCB. Pinsetter Controller PCB The functions of the comoponents and connectors on the Pinsetter Controller PCB are: (1) Adaptor Data (J6) - Connection for the communication cable to the optional Adaptor PCB. (2) Adaptor Power (J7) - Connection for the power cable to the optional Adaptor PCB. 4 Pinsetter Interface

7 (3) Configuration Jumpers (JP1, JP2, JP3) - These jumpers are used to set up the PCB for use with a scanner/pinsensor or a GS Series Pinsetter. All jumpers must be set the same. Installation Type All Installations Jumper Placement for JP1, JP2, and JP3 Short Pins 2 and 3 (A) (4) Diagnostic LED (Light-Emitting Diode) (D4) - This light flashes to indicate the operating condition and setup of the PCB. In newer installations, this LED is located on the front panel of the chassis. Flash Slow Rate Medium Fast Switch 8 position Meaning of S1 is set to the "ON" Switch 8 of S1 is set to the "OFF" position and communication to the scanner or pinsensor has been established. Switch 8 of S1 is set to the "OFF" position, but communication to the scanner or pinsensor has not been established. (5) ID Switch (S1) - Set the switches according to the following chart: Switch No. 1, 2 10 Pin Pinsetter 5 Pin Free Fall Pinsetter (Double Diamond) 5 Pin String Pinsetter Duck Pin String Pinsetter Settings No.1 On On No.2 On On 3-7 All Installation s No. 3 No. 4 No. 5 No. 6 No.7 8 Adaptor PCB Not Installe d Adaptor PCB Installed No. On 8 (6) Keyswitch (J5) - Not used. If the keyswitch is present, the cable from the switch should be disconnected. (7) Left Pinsetter (J10) - Connection to the left pinsetter. The Controller PCB controls the left pinsetter on/off and cycle count functions from this connection. Pinsetter Interface 5

8 (8) LLAN (Local Local Area Network) In (J4) - Connection for the cable that allows the PCB to communicate to the LGP. This connection allows scores and pinsetter information to be sent to the LGP and allows the LGP to control pinsetter functions. (9) LLAN Out (J3) - Connection that allows the LLAN to continue to additional devices if needed. Usually the TV-Only Monitor LLAN cables attach here. Refer to (16) Termination Jumper (JP4). (10) Main Power In (J2) - Connection for 28 VAC coming from the Secondary Console (Laneworx, Powerworx, and Touchworx) or LGP (Teamworx and Skyworx) Secondary Transformer. (11) Main Power Out to Transformer (J11) - Connection for the transformer located in the Pinsetter Interface Box. 28 VAC is sent to the transformer from this connection. (12) Mechanic s Override Switch (J8) - Connection to the override switch located on the front of the box. This switch allows the user to turn the pinsetters on manually. (13) Right Pinsetter (J9) - Connection to the right pinsetter. The Controller PCB controls the right pinsetter on/off and cycle count functions from this connection. (14) Scanner (J1) - Connection to the scanner or pinsensor (string machine) that provides 28 VAC power to the scanner/pinsensor and allows the scanner/pinsensor to communicate with the Pinsetter Interface Box. Refer to (8) LLAN In (J4). (15) Secondary Transformer Power In (J12) - Connection to the secondary side of the transformer located inside the box. 9.5 VAC power used by the Pinsetter Controller PCB to generate 5 VDC enters at this connection. (16) Termination Jumper (JP4) - Jumper used to terminate the LLAN signal if it does not continue to additional devices. Refer to (9) LLAN Out (J3). Set the jumper as follows: Configuration No additional devices connected to J3 (Terminated) Additional devices connected to J3 (Not terminated) Jumper Placement Short Pins 1 and 2 (T) Short Pins 2 and 3 (U) 6 Pinsetter Interface

9 Adaptor PCB The Adaptor PCB adapts the communication used by the Gamesetter of a GS Series Pinsetter and/or the BowlerTrack PCB so it can be understood by the LGP. This board is only installed in the Pinsetter Interface Box for earlier installations with Brunswick GS Series Pinsetter or the BowlerTrack system is being used on non- GS Series pinsetters. Refer to the figure titled Adaptor PCB (Part No ). Adaptor PCB (Part No ) The functions of the connections on the Adaptor PCB are: (1) Adaptor Data (J3) - Connection for the communication cable coming from the Pinsetter Controller PCB. (J6) (2) Adaptor Power (J1) - Connection for the power cable coming from the Pinsetter Controller PCB. (J7) Pinsetter Interface 7

10 (3) Diagnostic LED - This light flashes whenever the board is functioning properly. Flash Slow Rate Medium Fast Switch 8 position Meaning of S1 is set to the "ON" Switch 8 of S1 is set to the "OFF" position and communication to the scanner or pinsensor has been established. Switch 8 of S1 is set to the "OFF" position, but communication to the scanner or pinsensor has not been established. (4) Gamesetter/BowlerTrack PCB (J2) - Connection for communication to the Gamesetter of a GS Series Pinsetter or the BowlerTrack PCB. If both the Gamesetter and the BowlerTrack PCB are used, this signal is split by a Y cable so it can be routed to both locations. 8 Pinsetter Interface

11 GS Series Pinsetter Controller The GS Series Pinsetter Controller is used exclusively for centers containing GS-96 and GS-98 Pinsetters that had the scoring system installed between March 1997 and June The purpose of this box is to convert the LLAN (RS-485) information to a format that can be used by the Gamesetter of the GS machine. Through this communication, pinsetter on/off frame count monitoring and scoring is accomplished. The box is powered with 28VAC. GS Series Pinsetter Controller (1) J3 28VAC POWER IN (2) J4 28VAC POWER OUT (3) J5 9.5VAC POWER IN (4) J2 TO GAMESETTER (5) J8 JUMPER (6) J7 LLAN OUT (7) J6 LLAN IN (8) HEARTBEAT LED The functions of the connections on the GS Series Pinsetter Controller are: (1) 28 VAC Power In (J3) - Input for the voltage originating at the secondary transformer located in the secondary console or the LGP chassis. (2) 28 VAC Power Out (J4) - Output for the voltage going to the stepdown transformer located inside the Interface Box. Pinsetter Interface 9

12 (3) 9.5 VAC Power In (J5) - Input for the voltage returning for the step down transformer. This voltage is then changed to +5 VDC on the board. (4) J2 to Gamesetter (J2) - Connection for communication to the Gamemaker connection located on the Pinsetter Gamesetter Box. Information handled by this communication includes pinsetter on/off, frame count monitoring, scores, and special cycle information. (5) LLAN Termination Jumper (J8) - Jumper used to terminate the LLAN signal if it does not continue to additional devices. Refer to (6) LLAN Out (J7). Set the jumper as follows: Configuration No additional devices connected to J7 (Terminated) Additional devices connected to J7 (Not terminated) Jumper Placement Short Pins 1 and 2 (T) Short Pins 2 and 3 (U) (6) LLAN Out (J7) - Connection for LLAN Communication to additional devices on a lane pair. Currently the only device that connects to J7 is the TV Only monitor. If the monitors are not present, the connection is not used. Refer to (5) LLAN Termination Jumper (J8). (7) LLAN In (J6) - Connection for LLAN communication to J2 of the I/O PCB located in the LGP. All information needed by the Pinsetter Interface to control the machine, as well as the scores, are handled through this cable. (8) Heartbeat LED - The Heartbeat LED allows the user to monitor the communication between the board and the Gamesetter Box. The LED can have the following flash rates. Refer to (4) J2 to Gamesetter. Flash Rate Flash, Flash, Pause Meaning Normal Communication to Gamesetter Fast Flashing No Communication to Gamesetter 10 Pinsetter Interface

13 GS Series Pinsetter Setup Since the pinholder switches are used to count the pins, the Gamesetter or Consolidated Low Voltage Box must be programmed for double detect whenever the Adaptor PCB is used. This is done by moving switch No. 1 of the configuration switch (SW2), located on the Gamesetter I/O PCB or Consolidated CPU PCB, to the off position. Also, switch No. 2 must be turned to the on position so that the communication can be sent from the pinsetter through the proper connector. (Refer to the Pinsetter Service Manual for the setting of switch Nos. 3 and 4.) Refer to the figure titled Gamesetter I/O PCB Switch Settings. PCB Switch Settings (1) SWITCH NO. 1 (2) SWITCH NO. 2 (3) REFER TO THE PINSETTER SERVICE MANUAL FOR PROPER SETTING (4) OFF (5) ON (6) GAMESETTER I/O PCB (7) CONSOLIDATED CPU PCB The controls at the top of the Gamesetter or Consolidated Low Voltage Box must also be set properly in order for the system to score correctly. The keyswitch must be set to the normal position. The comline push button must be engaged so that the light turns on. Refer to the figure titled Gamesetter Setup. (1) COMLINE DISCONNECT (2) KEYSWITCH Gamesetter Setup (1) COMLINE DISCONNECT (2) KEYSWITCH Pinsetter Interface 11

14 PCB Replacement Setup Pinsetter Controller PCB Whenever the Pinsetter Controller PCB is replaced, it must be set up (configured) using jumpers and switches located on the PCB. Jumpers that must be checked include JP1, JP2, JP3, and JP4. Switches that must be set include switches 1-8 of S1. Refer to the figure titled Pinsetter Controller PCB (located earlier in this section) for jumper locations and configure the board according to the following tables. Configuration Jumpers (JP1, JP2, and JP3) These jumpers are used to set up the PCB for use with a scanner/pinsensor or a GS Series Pinsetter. All jumpers must be set the same. Installation Type All Installations Jumper Placement for JP1, JP2, and JP3 Short Pins 2 and 3 (A) Termination Jumper (JP4) This jumper is used to terminate the LLAN signal if it does not continue to additional devices. Refer to (9) LLAN Out (J3) (located earlier in this section). Set the jumper as follows: Configuration No additional devices connected to J3 (Terminated) Additional devices connected to J3 (Not terminated) Jumper Placement Short Pins 1 and 2 (T) Short Pins 2 and 3 (U) 12 Pinsetter Interface

15 S1 - ID Switch Switch No. 1, 2 10 Pin Pinsetter 5 Pin Free Fall Pinsetter (Double Diamond) 5 Pin String Pinsetter Duck Pin String Pinsetter Settings No.1 On On No.2 On On 3-7 All Installation s No. 3 No. 4 No. 5 No. 6 No.7 8 Adaptor PCB Not Installe d Adaptor PCB Installed No. 8 On GS Controller PCB When replacing the GS Controller PCB, jumper J8 must be set according to the following chart. Termination Jumper (J8) Configuration No additional devices connected to J7 (Terminated) Additional devices connected to J7 (Not terminated) Jumper Placement Short Pins 1 and 2 (T) Short Pins 2 and 3 (U) Pinsetter Interface 13

16 Cable Diagrams Pinsetter Interface External Cables for Brunswick A and A-2 Pinsetters and Skyworx, Teamworx (1) LANE GROUP PROCESSOR (2) PINSETTER CONTROLLER (3) CCD SCANNER (4) TO CABLE ( ) (5) TO TV ONLY MONITOR (6) BOWLERTRACK (OPTIONAL) (7) ADAPTOR PRINTED CIRCUIT BOARD Pinsetter Interface External Cables for Brunswick A and A-2 Pinsetters and Powerworx, Laneworx, Touchworx (1) PRIMARY CONSOLE (2) PINSETTER CONTROLLER (3) CCD SCANNER (4) TO CABLE ( ) (5) SECONDARY CONSOLE (6) BOWLERTRACK (OPTIONAL) (7) ADAPTOR PRINTED CIRCUIT BOARD (8) TO TV ONLY MONITOR 14 Pinsetter Interface

17 Pinsetter Interface External Cables for AMF Pinspotters and Skyworx, Teamworx (1) LANE GROUP PROCESSOR (2) PINSETTER CONTROLLER (3) CCD SCANNER (4) TO CABLE ( ) (5) TO TV ONLY MONITOR (6) BOWLERTRACK (OPTIONAL) (7) ADAPTOR PRINTED CIRCUIT BOARD Pinsetter Interface External Cables for AMF Pinspotters and Powerworx, Laneworx, Touchworx (1) PRIMARY CONSOLE (2) PINSETTER CONTROLLER (3) CCD SCANNER (4) TO CABLE ( ) (5) SECONDARY CONSOLE (6) BOWLERTRACK (OPTIONAL) (7) ADAPTOR PRINTED CIRCUIT BOARD (8) TO TV ONLY MONITOR Pinsetter Interface 15

18 Pinsetter Interface External Cables for String Machines (Models P, R, CA-1, M, and S) and Skyworx, Teamworx (1) LANE GROUP PROCESSOR (2) PINSETTER CONTROLLER (3) PINSENSOR (4) TO PINSETTER (5) TO TV-ONLY MONITOR (6) BOWLERTRACK (OPTIONAL) (7) ADAPTOR PRINTED CIRCUIT BOARD Pinsetter Interface External Cables for String Machines (Models P, R, CA-1, M, and S) and Powerworx, Laneworx, Touchworx (1) PRIMARY CONSOLE (2) PINSETTER CONTROLLER (3) PINSENSOR (4) TO PINSETTER (5) SECONDARY CONSOLE (6) TO TV-ONLY MONITOR (7) ADAPTOR PRINTED CIRCUIT BOARD (8) BOWLERTRACK (OPTIONAL) 16 Pinsetter Interface

19 Pinsetter Interface External Cables for Brunswick GS Series Pinsetters and Skyworx, Teamworx (Earlier Installations) (1) LANE GROUP PROCESSOR (2) PINSETTER CONTROLLER (3) PINSENSOR (4) TO PINSETTER (5) TO TV-ONLY MONITOR (6) GAMESETTER AND OR BOWLERTRACK (7) ADAPTOR PRINTED CIRCUIT BOARD (OPTIONAL) Pinsetter Interface External Cables for Brunswick GS Series Pinsetters and Powerworx, Laneworx, Touchworx (Earlier Installations) (1) PRIMARY CONSOLE (2) PINSETTER CONTROLLER (3) TO GAMESETTER AND/OR BOWLERTRACK (4) ADAPTOR PRINTED CIRCUIT BOARD (5) SECONDARY CONSOLE (6) TO TV-ONLY MONITOR (7) TO PINSETTER Pinsetter Interface 17

20 Pinsetter Interface External Cables for Brunswick GS Series Pinsetters and Skyworx, Teamworx (March 1997 and Later Installations) (1) LANE GROUP PROCESSOR (2) GS PINSETTER CONTROLLER (3) GAMESETTER AND/OR BOWLERTRACK (4) TO TV-ONLY MONITOR Pinsetter Interface External Cables for Brunswick GS Series Pinsetters and Powerworx, Laneworx, Touchworx (March 1997 and Later Installations) (1) PRIMARY CONSOLE (2) GS PINSETTER CONTROLLER (3) TO GAMESETTER AND/OR BOWLERTRACK (OPTIONAL) (4) TO TV-ONLY MONITOR (5) SECONDARY CONSOLE 18 Pinsetter Interface

21 Primary Console to Pinsetter Interface Local LAN Cable (Part No ) (1) DRAIN (2) LOCAL AREA NETWORK A (3) LOCAL AREA NETWORK B (4) +12 VOLTS DIRECT CURRENT (5) GROUND (6) TO J2 ON PRIMARY CONSOLE INPUT/OUTPUT PRINTED CIRCUIT BOARD (7) TO J4 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD Secondary Console to Pinsetter Interface 28 VAC (Part No ) (1) 28 VOLTS ALTERNATING CURRENT (2) 28 VOLTS ALTERNATING CURRENT RETURN (3) 28 VOLTS ALTERNATING CURRENT FROM SECONDARY CONSOLE TRANSFORMER (4) TO J2 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD Pinsetter Interface to String Machine (Part No ) (1) DRAIN (2) NO CONNECTION (3) TRANSMIT (4) RECEIVE (5) SCANNER CLOCK (6) GROUND (7) 28 VOLTS ALTERNATING CURRENT (8) 28 VOLTS ALTERNATING CURRENT RETURN (9) SHIELD (10) TO J1 ON PINSETTER CONTROLLER PRINTED (11) TO J3 ON STRING INTERFACE (12) TO J6 ON STRING INTERFACE CIRCUIT BOARD Pinsetter Interface 19

22 Pinsetter Controller PCB to TV-Only LLAN (Part No ) (1) DRAIN (2) NO CONNECTION (3) LOCAL AREA NETWORK A (4) LOCAL AREA NETWORK B (5) +12 VOLTS DIRECT CURRENT (6) GROUND (7) TO OVERHEAD LOCAL AREA NETWORK (8) TO J3 ON PINSETTER CONTROLLER PRINTED INPUT CIRCUIT BOARD Frameworx A-2 Pinsetter Y Power and Cycle Cable (Part No ) (1) CYCLE COUNT (2) AUTOMATIC PINSETTER POWER (3) COMMON (4) TO CCD SCANNER NEW PINS SOLENOID (5) NO CONNECTION (6) TO J10 ON PINSETTER CONTROLLER CABLE ( ) PRINTED CIRCUIT BOARD (7) TO J9 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD 20 Pinsetter Interface

23 Scanner to Pinsetter Interface Box Cable (Part No ) (1) DRAIN (2) NO CONNECTION (3) TRANSMIT (4) RECEIVE (5) SCANNER CLOCK (6) GROUND (7) 28 VOLTS ALTERNATING CURRENT (8) 28 VOLTS ALTERNATING CURRENT RETURN (9) SHIELD (10) TO J1 ON PINSETTER CONTROLLER PRINTED (11) TO J67 ON CCD SCANNER (12) TO J1 ON CCD SCANNER CIRCUIT BOARD Pinsetter Interface to GS Series Cable (Part No ) (1) DRAIN (2) GROUND (3) SIGNAL B (4) SIGNAL A (5) +12 VOLTS DIRECT CURRENT (6) SHIELD (7) NO CONNECTION Pinsetter Interface Adaptor Power Cable (Part No ) (1) TO J7 ON PINSETTER CONTROLLER (2) TO J1 ON ADAPTOR PRINTED CIRCUIT BOARD (3) +5 VOLTS DIRECT CURRENT PRINTED CIRCUIT BOARD (4) GROUND (5) +24 VOLTS DIRECT CURRENT Pinsetter Interface 21

24 Pinsetter I/O PCB to Adaptor PCB Data Cable (Part No ) (1) TO J1 ADAPTOR PRINTED CIRCUIT BOARD (2) TO PINSETTER CONTROLLER PRINTED CIRCUIT BOARD LGP to Pinsetter Interface Box LLAN Cable - Skyworx, Teamworx (Part No ) (1) TO J2 ON LANE GROUP PROCESSOR (2) TO J4 ON PINSETTER CONTROLLER PRINTED (3) DRAIN INPUT/OUTPUT PRINTED CIRCUIT BOARD CIRCUIT BOARD (4) LOCAL AREA NETWORK A (5) LOCAL AREA NETWORK B (6) +12 VOLTS DIRECT CURRENT (7) GROUND (8) SHIELD LGP to Pinsetter Interface Box Power Cable - Skyworx, Teamworx (Part No ) (1) TO LANE GROUP PROCESSOR SCANNER (2) TO J2 ON PINSETTER CONTROLLER PRINTED (3) 28 VOLTS ALTERNATING CURRENT TRANSFORMER CIRCUIT BOARD (4) 28 VOLTS ALTERNATING CURRENT RETURN 22 Pinsetter Interface

25 Pinsetter Interface Controller Wiring Diagram (Part No xx) (1) ADAPTOR DATA CABLE (2) PINSETTER CONTROLLER PRINTED CIRCUIT (3) TRANSFORMER MOUNTED TO INSIDE BOARD OF BASE ENCLOSURE (4) ADAPTOR PRINTED CIRCUIT BOARD (5) TO ADAPTOR PRINTED CIRCUIT BOARD, (6) OVERRIDE SWITCH MOUNTED ON POWER CABLE CONNECT TO J1. SIDE OF BASE ENCLOSURE (7) BASE ENCLOSURE WALL (8) NUT (9) CONNECTOR (10) LIGHT-EMITTING DIODE MOUNTED ON (11) KEYSWITCH MOUNTED ON SIDE OF (12) TO ADAPTOR PRINTED CIRCUIT SIDE OF BASE ENCLOSURE BASE ENCLOSURE BOARD, CONNECT TO J3. Pinsetter Interface Controller Override Switch Cable (Part No ) (1) NUMBERS ARE FOR REFERENCE ONLY (2) TO J8 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD Pinsetter Interface 23

26 Pinsetter I/O Keyswitch Cable (Part No ) (1) POSITION 1 (2) POSITION 7 (3) TO J5 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD Pinsetter Interface Controller Transformer (Part No ) (1) NO CONNECTION (2) TO J12 ON PINSETTER CONTROLLER (3) TO J11 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD PRINTED CIRCUIT BOARD (4) PRIMARY 28 VOLTS ALTERNATING (5) SECONDARY 9.5 VOLTS ALTERNATING CURRENT CURRENT Cycle Count for GS Series Pinsetter Cable (Part No ) (1) NO CONNECTION (2) TO J9 OR J10 ON PINSETTER (3) TO P6 ON HIGH VOLTAGE BOX CONTROLLER PRINTED CIRCUIT BOARD 24 Pinsetter Interface

27 A-2 Pinsetter New Pins Solenoid to Low Voltage Box (Part No ) (New Universal Voltage) (1) ASSEMBLE TO 12-PIN MOLEX PLUG IN NEW (2) COMMON (3) 44 /144 NORMALLY OPEN PINS SOLENOID BOX ( ) PER POSITION NUMBER SHOWN (4) 0 NORMALLY OPEN (5) GROUND (6) TO RELAY T2 ON ( ) (7) TO PIN NO. 2 SOLENOID ON (8) GROUND LUG ( ) Pinsetter Interface 25

28 A-2 Pinsetter New Pins Solenoid to Low Voltage Box (Part No ) (Japanese Pinsetter) (1) ASSEMBLE TO 12-PIN MOLEX PLUG IN NEW (2) COMMON (3) 44 /144 NORMALLY OPEN PINS SOLENOID BOX ( ) PER POSITION NUMBER SHOWN (4) 0 NORMALLY OPEN (5) GROUND (6) TO RELAY T2 ON ( ) (7) TO PIN NO. 2 SOLENOID ON (8) TL1 BROWN WIRE ( ) 26 Pinsetter Interface

29 A-2 Pinsetter New Pins Solenoid to CCD Scanner (Part No ) (1) TO NEW PINS SOLENOID LANE 1 (2) TO NEW PINS SOLENOID LANE 2 (3) NO CONNECTION (4) CYCLE COUNT ODD LANE (5) AUTOMATIC PINSETTER POWER ODD LANE (6) COMMON (7) NEW PINS SOLENOID VCC (8) NEW PINS SOLENOID GROUND (9) SWITCH CLUSTER GROUND (10) SECOND BALL (11) 0 SWITCH (12) 44 /144 SWITCH (13) CYCLE COUNT EVEN LANE (14) AUTOMATIC PINSETTER POWER EVEN LANE (15) TO CABLE ( ) (16) TO CCD SCANNER DATA PROCESSOR (J8) (17) TO CCD SCANNER DATA PROCESSOR (J9) (18) LEFT (19) RIGHT Pinsetter Interface 27

30 AMF Interface to CCD Scanner (Part No ) (1) TO AMF INTERFACE PRINTED CIRCUIT BOARD (2) NO CONNECTION (3) POWER DIRECT CURRENT, LANE 1 (4) GROUND AMF, LANE 1 (5) POWER DIRECT CURRENT, LANE 2 (6) GROUND AMF, LANE 2 (7) FOUL, LANE 1 (8) FOUL, LANE 2 (9) SWEEP UP, LANE 1 (10) TABLE SWEEP, LANE 1 (11) POWER, LANE 1 (12) SECOND, LANE 1 (13) TABLE SWEEP, LANE 2 (14) POWER, LANE 2 (15) SECOND, LANE 2 (16) GROUND SCORER, LANE 2 (17) GROUND SCORER, LANE 1 (18) SWEEP UP, LANE 2 (19) TO CABLE ( ) (20) TO J6 ON SCANNER PRINTED CIRCUIT (21) TO J8 ON SCANNER PRINTED CIRCUIT BOARD BOARD (22) TO J9 ON SCANNER PRINTED CIRCUIT BOARD Universal Interface Adaptor String Machine (Part No ) (1) NO CONNECTION (2) TO AUTOMATIC PINSETTER POWER (3) TO AUTOMATIC PINSETTER CYCLE COUNT (4) POWER + (5) POWER - (6) CYCLE COUNT + (7) CYCLE COUNT - (8) TO J10 OR J9 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD 28 Pinsetter Interface