CATALOGUE OF PRODUCTS

Transcription

1 CATALOGUE OF PRODUCTS BORIMA -EAD; tel. 359//670// ; fax 359//670// ;

2 QC - MODULES ( QUICK CONNECTING MODULES ) AND ACCESSORIES It is a modern technology,which enables cable connections to function inside the telecommunication networks by pressing in single - core cables. The QC ( quick connecting modules ) provide: Quick connection of copper wires; Solid electric connection; Reliable mechanical contact; Direct work without advance preparation of the wires; Wires with a plastic insulation coating are with diameter from Ø 0.32 to Ø 0.8 mm and diameter of a insulation coating to Ø 1.47 mm. BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

3 QC - MODULES ( QUICK CONNECTING MODULES ) AND ACCESSORIES QC DISCONNECTION MODULE Module QC - Disconnection module is used for connecting of cables in Main and Intermediate Distribution frames, Distribution Cabinets and Distribution End Boxes. It can disconnect the circuit and enable the measurements over the cable network. The module consists of: Base and Body - made of polycarbonate - incombustible ( fire resistant ); Working lamella - made of phosphoric bronze and galvanized with silver with a thickness of 8 μm; Pressing lamella - made of phosphoric bronze. DISCONNECTION MODULE WITH PROTECTION CARTRIDGE In the base of disconnection module is built-in protection cartridge for arresters of voltage protection. In the cartridge are mounted high voltage arresters, which protected eight and ten telephone pairs. Additional elements: Contact lamella and grounding comb made of phosphoric bronze and galvanized with silver with a thickness of 8μm; Protection cover - made of polycarbonate - incombustible ( fire - resistant ) CONNECTION MODULE Module QC - Connection module is used for connecting of cables in Main and Intermediate Distribution frames, Distribution Cabinets and Distribution End Boxes. It gives a possibility for measuring the cable network. The module consists of: Base and Body made of polycarbonate - incombustible ( fire resistant ); Working lamella made of phosphoric bronze and galvanized with silver with thickness of 8 μm. QC GROUNDING MODULE Module QC - grounding is used for derivation of control wires with a perforation plastic insulation to Main or Intermediate Distribution frame, Distribution Cabinet or Terminal Distribution Box. It is the same construction as connection module, but it has only 4 pcs working lamellas. BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

4 QC - MODULES ( QUICK CONNECTING MODULES ) AND ACCESSORIES PROTECTION CARTRIDGE FOR DISCONNECTION MODULE Protection cartridge for disconnection module is an independent module, which is mounted on disconnection module and allows multiple mounting and dismounting. It is used for voltage protection for 8 or 10 telephone pairs. In the cartridge are mounted high voltage arresters. It consists of: Body, cartridge 02 - made of polycarbonate - incombustible Cover - labeling plate - made of polycarbonate - incombustible, transparent. Contact lamella, grounding comb - made of phosphoric bronze and galvanized with tin - bismuth ( SuBs ) with thickness 10 μm. PROTECTION CARTRIDGE FOR CONNECTION MODULE Protection cartridge for connection module has the same construction and function as the protection cartridge for disconnection module, and the contact lamellas are suitable for mounting on connection module. PROTECTION CARTRIDGE FOR ONE PAIR Protection cartridge for one pair is an independent module which is mounted on disconnection module. It used for voltage and current protection for one pair. It allows multiple mounting and dismounting. On one disconnection module can be mounted simultaneously 10 ( 8 ) protection cartridges for one pair. It consists of: Body - made of polycarbonate incombustible ( fire resistant ); PCB for voltage and current protection; Grounding comb - made of phosphoric bronze and galvanized with tin - bismuth (SuBs) with thickness 10 μm. BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

5 QC - MODULES ( QUICK CONNECTING MODULES )AND ACCESSORIES TOOL AND DEVICES FOR MOUNTING AND DISMOUNTING TERMINATION TOOL ( TERMINATOR ) It is used for pushing and cutting the excess wire( cable ) in the slot of working lamella of the modules QC Borima. Body of the termination tool - made of polycarbonate - incombustible ( fire resistant ). The tool consists of: Hook for taking out a pushed wire ( cable ); Lamella for taking out the arresters from the nests of the protection cartridge. REMOVING TOOL It is used for taking out the QC modules from the mounting back mount frames. Made of polycarbonate - incombustible ( fire resistant ). COMPENSATOR The device is used to provide the necessary working advance of the wires on mounting of the modules of Main and Intermediate Distribution frame. Made of polycarbonate - incombustible ( fire resistant) ACCESSORIES Labelling plate It is used for placing of note with the help of two consoles / left and right /. The labelling plate and consoles are made of polycarbonate - incombustible (fire resistant). Marking cap It is used for marking an exact pair from the module QC. Colour : red, yellow, green, blue or brown.. Made of polycarbonate - incombustible. Cut - off - plug It is used to interrupt the circuit of the disconnection module QC or disconnection protection module QC. Colour: red, yellow, green, blue or brown. Made of polycarbonate - incombustible. Cut - off test cord for QC disconnection and disconnection protection modules It is used as an assistant tool on certain electrical measuring of the circuit. It is equipped with four-wired cord. Body - made of polycarbonate - incombustible. Continuity test cord It is used as an assistant tool on certain electrical measuring of the circuit. It is equipped with four-wired cord. Body made of polycarbonate incombustible. BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

6 QC - MODULES ( QUICK CONNECTING MODULES ) AND ACCESSORIES Part Type Description - quick connecting system Height H Width W Depth D Colour code (to RAL) 8326 / 8325 DM-QC - 8" Module - QC - disconnection 8" 33 ± ± ± / / 8328 DM-QC - 10" Module - QC - disconnection 10" 33 ± ± ± / / 8334 DPM-QC- 10" Module - QC - disconnection with 32.5 ± ± ± /7001 protection cartridge 10" 8331 / 8330 CM-QC - 8" Module - QC - connection 8" 33 ± ± ± / / 8332 CM-QC - 10" Module - QC - connection 10" 33 ± ± ± / / 8321 GM-QC - 8" Module - QC - ear thing and 33 ± ± ± /7001 shielding 8" 8322 GM-QC - 10" Module - QC - ear thing and 33 ± ± ± /7001 shielding 10" 8400 / 8402 PCDM-QC 8" Protection cartridge for 37 ± ± 23.6 ± /7001 disconnection module - 8" / 8411 PCDM-QC 10" Protection cartridge for 37 ± ± 23.6 ± /7001 disconnection module - 10" / 8406 PCCM-QC 8" Protection cartridge for 37 ± ± 23.6 ± /7001 connection module - 8" / 8415 PCCM-QC 10" Protection cartridge for connection module - 10" 37 ± ± ± / CCCP-QC 1" Cartridge for current and voltage /7001 protection of 1" 8524 Terminator Termination tool RT 8" Removing tool - for Back mount , frame 8" RT 10" Removing tool - for Back mount frame 10" 8212 C 8" Compensator - for Back mount frame 8" 8211 C 10" Compensator - for Back mount frame 10" / 8485 LP 8" Labeling plate - Module - QC 8" 22 ± ± ± / / 8487 LP 10" Labeling plate - Module - QC 10" 22 ± ± ± / MC Marking cap 4.4 ± ± ± /3020/ 6017/ COP Cut - off - plug 8.6 ± ± ± /3020/ 6017/ COTCDM-QC Cut - off test cord for QC disconnection 8516 CTC-QC Continuity test cord HVA High voltage cartridge Ø 8 6 BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

7 QC - MODULES ( QUICK CONNECTING MODULES )AND ACCESSORIES Colour code ( to AL ) Colour 7035 light - grey 7001 dark - grey 3020 red 1018 yellow 6017 green 5012 blue 8001 brown Technical Data Flammability class VO to UL 94 Environment temperature -50 C to +60 C Relative humidity to 80% For modules QC Contact resistance in zone of pressing wires < 25 m Drilling voltage between two next lamellas 2000 Veff to frequency 50Hz per 1 min Using cables for wires with plastic insulation coating with diameter 0.32 mm to 0.8 mm and insulation coating to 1.47 mm Weight: Module QC - connection, disconnection - 8" 40.4 ± 1 g Module QC - connection, disconnection - 10" 46.5 ± 1 g Module QC - disconnection with protection cartridge ± 1 g 10 ( with arresters ) Protection cartridge for connection, 67.0 ± 1 g disconnection module QC for 8 ( with arresters) Protection cartridge for connection, 78.8 ± 1 g disconnection module QC for 10 ( with arresters) ELECTRICAL PARAMETERS AND GEOMETRIC DIMENSIONS OF USING ARRESTERS A. Electrical parameters B. Geometric parameter - spark over voltage of the arrester (100 V/s) 230 V ± 20% - body - cylindrical - impulse spark over voltage (1 kv/μs) < 750 V - base diameter - 8 mm - voltage extinction (R = 600 ; RC = 150 /100 nf) > 100 V - height mm ± insulation resistance (100 V=) > 1 G - capacity (for 1 MHz) 5 pf - AC discharge current (10 times; 1 s; 50 Hz) 5 A - discharge current (8/20 s; 10 times) 5 ka BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

8 JOINT CLOSURE FOR TELEPHONE NETWORK NON PRESSURIZED XAGA 550 The Joint closure for telephone networks non pressurized - XAGA 550 is a heat shrinkable closure, used for protection of the cable connections in the telephone networks non pressurized. It is used for installation of local, underground and pipe cables with a lead or plastic coating. It uses the Raychem - technology of composite materials; the closure XAGA 550 guarantees an excellent mechanical stability during and after installation. The closure includes heat shrinkable sleeve, which isolates, forms and clamps the connection beam and the metal canister, which forms the internal volume of the closure. Each end of the closure can branch up to 3 cables, and a three finger clamp with thermo- melting adhesive is used. The three finger clamp ( clip ) is a part from the branched kit BOKT - 5. One branched kit is designed for max. 2 cables branched in the one end only. The heat - shrinkable sleeve is: - CWST - reinforced with integrated metal coating; - WRGT - non-reinforced. The closures XAGA 550 are with capacity to BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

9 XAGA 550 XAGA 550 kit consists of: Heat-shrinkable sleeve; Metal canister; flexible channels and under clip; Aluminum foils; Emery tissue; Silica gel; Aluminum cable foils; Installation procedure; Shield continuity wire assembly. BOKT KIT -5 consists of: Three finger clamp (clip) with thermo-melt adhesive; Shield continuity wire assembly; Aluminum foils. Description BOKT -5 - BOKT -5 S-branched kit with small clamp; - BOKT -5 M-branched kit with middle clamp; - BOKT -5 L-branched kit with large clamp. DIMENSIONS Dimensions in mm Part Type Number of pairs Max.dia.over liner D max Min.cable dia. d min Max. jacket opening L Max. sleeve length S Clamp CWST Reinforced closure 8376 XAGA / S 8377 XAGA / S 8378 XAGA / S 8379 XAGA / S 8380 XAGA / S 8381 XAGA / S 8385 XAGA / S 8386 XAGA / S 8387 XAGA / S 8382 XAGA / M 8383 XAGA / M 8384 XAGA / M BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

10 BACK MOUNT FRAMES FOR MOUNTING OF MODULES - QC The back mount frames are an universal equipment, used for attaching and mounting of modules QC. The back mount frames are designed for the following modules: Modules QC, produced by BORIMA -EAD.; Modules KRONE - series LSA+. The capacity of the back mount frame: from 10 to 500 for 10 module; from 8 to 400 for 8 module. Material: chrome nickel steel. Physical and mechanical characteristics of the material Hardness, HB Electrical conductivity, s 0.85 Heat conductivity, W / ( mk ) 14 Magnetic conductivity, Wb / A BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

11 BACK MOUNT FRAMES FOR MOUNTING OF MODULES - QC DIMENSIONS Dimensions in mm Modules QC BORIMA 8" Modules QC BORIMA 10" KRONE 10" LSA + t W V T n t W V T n t W V T n Part Type Description T 22-8" T 35-8" T 22-10" T 35-10" According customer request According customer request T 22 - LSA T 35 - LSA Back mount frame for mounting of 8 module T 22 Back mount frame for mounting of 8 module T 35 Back mount frame for mounting of 10 module T 22 Back mount frame for mounting of 10 module T 35 Back mount frame for mounting of 10 LSA module T 22 Back mount frame for mounting of 10 LSA module T 35 BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

12 MULTI - PAIR SPLICING CONNECTOR MARK III The Multi - pair splicing connector MARK III is used for connecting pair cables in the telecommunication network by pressing of conductors with copper wires. The connectors provide: quick connection of copper wires ; solid electrical contact; reliable mechanical contact; direct work without advance preparation of the wires; different kinds of connections with a diameter of the wires from Ø 0.32 mm to Ø 0.8 mm and a plastic insulation coating; Construction: the body, consists of two plastic halves with built in working and cutting lamellas - made of shock - resistant polycarbonate ; cover ( upper and lower ) - made of shock - resistant polycarbonate. The built in working cutting lamellas are made of phosphoric bronze and a galvanized coating with tin - bismuth (SuBs). Production: MARK III :10 pair - it is designed to connect 10 pairs of multi - pair cable with copper wires. MARK III:25 pairs - it is designed to connect 25 pairs of multi - pair cable with copper wires. Tools: We offer you a kit of tools, production of AMP. to work with multi - pair splicing connector. BORIMA - EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

13 MARK III TECHNICAL DATA Product MARK III - 10" MARK III - 25" Length D, mm Width W, mm Height H, mm Weight, g MATERIAL AND COLOUR OF THE PRODUCT Product MARK III - 10" MARK III - 25" Base(1) Cover (2) Cover (3) Material Colour Material Colour polycarbonate orange, RAL polycarbonate and/ orange, RAL 1028 and/ PBT 1028 PBT polycarbonate reseda, RAL polycarbonate and/ reseda, RAL 1032 and/ PBT 1032 PBT polycarbonate reseda, RAL polycarbonate and/ transparent and/ PBT 1032 PBT Part Type Description MARK III - 10" - jelli filled MARK III - 10" - jelli filled 8302 MARK III - 10" - dry MARK III - 10" - dry MARK III - 25" - jelli filled MARK III - 25" - jelli filled 8307 MARK III - 25" - dry 8308 MARK III - 25" - dry Multi-pair connector for 10 jelly filled half-tap Multi-pair connector for 10 jelly filled splicing Multi-pair connector for 10 dry half-tap Multi-pair connector for 10 dry splicing Multi-pair connector for 25 jelly filled splicing Multi-pair connector for 25 jelly filled half-tap Multi-pair connector for 25 dry half-tap Multi-pair connector for 25 dry splicing BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

14 SINGLE HERMETIC CONNECTORS - SHC The connectors SHC are designed to enable the cable connections to function in telecommunication network by pressing of conductors with copper wires. The connectors provide: quick connection of single copper wires; an auspicious mechanical contact; an auspicious electrical contact; no necessity of advance preparation of the wires; different kinds of connections with a diameter of the wires from 0.32 mm to 0.8 mm and a plastic insulation coating; Construction: Body and cover -made of incombustible polycarbonate ( fire - resistant ); Contact lamella - made of phosphoric bronze and a galvanized tin-bismuth ( SuBs ) or tin-lead ( SuPv ) coating - 10 μm; The internal space of the connectors ( chamber ) is filled with hydrophobic filler, which guarantees protection of the contact from humidity and chemical exposures. The pressing of the wires is made by special tongs. BORIMA EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

15 SHC TECHNICAL DATA Height H, mm 6.5 Width W, mm 8.8 Depth D, mm 12.4 Weight, g 0.52 Flammability class VO to UL 94 Contact resistance smaller than 40 m Environment -50 C to +60 C temperature Product SHC Body Cover Material Polycarbonate glass filled Polycarbonate glass filled Colour Transparent Yellow, RAL 1018 Dimension in, mm Part Type Description 8482 SHC Single hermetic connector for copper wires with diameter 0.32 to 0.8 mm 8204 Tongs for connector Tool for pressing of SHC BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

16 MAIN AND INTERMEDIATE DISTRIBUTION FRAME ( MDF ) The main and the intermediate distribution frame ( MDF ) is designed to connect the subscriber lines, connection lines of the cable telecommunication network and the station equipment. Inside the distributor can be; arranged the connections, interrupted the line; measured the stationary and linear part of the network; current and voltage protected the station equipment and other necessary technical actions. It is designed to use modules QC. The main and the intermediate distribution frame ( MDF ) has a cylindrical modular construction, which allows accomplishment of different kinds of combinations in height and length. Construction: base - supports the construction and is used for attaching to the floor. It includes a back mount frame for a cable beam. It is made of sheet steel and coated with polyester against corrosion; working part - includes a vertical support column, horizontal support elements, metal details, which form arranged construction, coated with polyester against corrosion, plastic support for back mount frames, made of chrome - nickel sheet - metal, which are designed to mount modules QC; upper part - is used for mounting the construction to the ceiling, it includes a cable beam crib. It is made of steel coated with polyester against corrosion. Types: Bilateral distribution frame Borima - If the designer decides and if there is enough space, the construction can be used as a main distributor of a bigger exchange (it is recommended for more than 4000 telephone posts ).It is possible to work ( mounting and serves ) on the both sides. The location of the back mount frames is: on the face side - horizonta l, and on back side - vertical. Wall two - facade distribution frame Borima - It is mounted on the wall. The position of the back mount frames is : horizontal back mount frames for subscriber side - in the upper part of the construction; vertical back mount frame for network side - in the lower part of the construction. Wall one - facade distribution frame Borima - It is mounted on a wall. The position of the back mount frames is: vertical back mount frames for subscriber and linear part of the telecommunication network. Reconstruction of old type of distribution frame - It is used to restore an existing bilateral construction with modules QC. It is done by a console for reconstruction of MDF - a vertical part and a support element for reconstruction of a horizontal part. BORIMA - EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

17 MAIN AND INTERMEDIATE DISTRIBUTION FRAME (REPARTITOR) TECHNICAL DATA Horizontal step Tw, mm 250 Vertical step Tn, mm 250 Depth D, mm - bilateral 850 distribution frame Depth D, mm - wall 700 distribution frame Colour Light - grey, to RAL7035 Relative humidity, % 80 Environment temperature to 50 C Type MDF TFDF Borima WTFDF Borima WOFDF Borima RC-V RSE-H Description Two facade distribution frame for modules - QC Wall two - facade distribution frame for modules - QC Wall one - facade distribution frame for modules - QC Reconstruction Console of MDF - vertical part Reconstruction Support element of MDF - horizontal part BMFH-H Back mount frames holder - horizontal part BMFH-V Back mount frames holder - vertical part CFR Cartridge for rosette of MDF BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

18 CROSS CONNECTION CABINET CCC P The Cross connection cabinet CCC P is an equipment, which connects the main and the distributing cables in the telecommunication network. The cabinet gives the possibility to arrange the connections, to interrupt the line and to measure the telecommunication cable network. The cabinet is adapted to outdoor use on a concrete fundament. The body of the cabinet is made of glass filled polycarbonate, that is incombustible, UV protected, shock-proof, and high weather - resistant. The base and the roof are made of incombustible polycarbonate. Hermetically the cabinet is isolated by PVC sealing profile, that keeps the working parameters in a wide temperature scope /According to DIN 7863 /.Hermetically the openings of the incoming and the outgoing cables are isolated by waterproof compounds and fillers. The cabinet is equipped with back mount frames ( channels ) for modules QC Borima. The EQUIPMENT consists of : modules QC - disconnecting, connecting and grounding modules; main frame / contour / - made of zinc galvanized steel and subsequently coated with polyester paint. channels for installing modules QC Borima 4 pcs.; the length is according to the capacity of the cables; 4 entrances between the base and the body, that secure watertight passage of all the cables / incoming and outgoing /; arranged rings; cable holders / incoming and outgoing / in the base and the body of the cabinet; fundament bolts for easy installation and levelling ; 4 pieces of grounding bolts ; a set of lock. A System for controlling and protecting the cabinet is made according to an order. BORIMA -EAD.; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

19 CROSS CONNECTION CABINET CCC P Type H W D CCC 300 P CCC 400"P CCC 600"P CCC 800"P CCC 900"P CCC 1200"P Inputs and outputs of the 4 pcs 90 mm each back mount frames Flammability class VO to UL 94 Relative humidity to 100% Environment -40 C to +70 C temperature MATERIAL AND COLOUR OF THE PRODUCT Base elements Material Colour Body polycarbonate glass - filled light - grey similar to RAL 7035 Base polycarbonate glass - filled light - grey similar to RAL 7035 metal with organic coating black similar to RAL 9005 Roof polycarbonate glass - filled light - grey similar to RAL 7035 metal with organic coating black similar to RAL 9005 Part Type Description Equipment with modules QC 8500 CCC 300"P Cross connection cabinet with 4 back mount frames by 9 modules - QC each connection module - 16pcs disconnection module - 16pcs grounding module - 4pcs 8501 CCC 400"P 8502 CCC 600"P 8503 CCC 800"P 8504 CCC 900"P 8505 CCC 1200"P Cross connection cabinet with 4 back mount frames by 11 modules - QC each Cross connection cabinet with 4 back mount frames by 16 modules - QC each Cross connection cabinet with 4 back mount frames by 21 modules - QC each Cross connection cabinet with 4 back mount frames by24 modules - QC each Cross connection cabinet with 4 back mount frames by 31 modules - QC each connection module - 20pcs disconnection module - 20pcs grounding module - 4pcs connection module - 30pcs disconnection module - 30pcs grounding module - 4pcs connection module - 40pcs disconnection module - 40pcs grounding module - 4pcs connection module - 46 pcs disconnection module - 46 pcs grounding module - 4pcs connection module - 60pcs disconnection module - 60pcs grounding module - 4pcs BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

20 CROSS CONNECTION CABINET CCC P TECHNICAL DATA Dimension in mm Type H W D CCC 1400 P CCC 1600 P CCC 1800 P CCC 2400" P CCC 2800" P Inputs and outputs of the back mount frames Flammability class 8 pcs 90 mm each V0 to UL94 Relative humidity to 100% Environment -40 C to +70 C temperature MATERIAL AND COLOUR OF THE PRODUCT Base elements Material Colour Body polycarbonate glass - filled light - grey similar to RAL 7035 Base polycarbonate glass - filled light - grey similar to RAL 7035 Roof polycarbonate glass - filled metal with organic coating light - grey similar to RAL 7035 light - grey similar to RAL 7035 Part No Type Description Equipment with modules QC 8506 CCC 1400 P 8507 CCC 1600 P 8508 CCC 1800 P 8509 CCC 2400" P 8510 CCC 2800 P Cross connection cabinet with 8 back mount frames by 19 modules - QC each Cross connection cabinet with 8 back mount frames by 21 modules - QC each Cross connection cabinet with 8 back mount frames by 24 modules - QC each Cross connection cabinet with 8 back mount frames by 31 modules - QC each Cross connection cabinet with 8 back mount frames by 36 modules - QC each connection module - 72 pcs disconnection module-72 pcs grounding module - 8pcs connection module - 80 pcs disconnection module-80 pcs grounding module - 8pcs connection module - 92 pcs disconnection module-92 pcs grounding module - 8pcs connection module - 120pcs disconnection module - 120pcs grounding module - 8pcs connection module - 140pcs disconnection module - 140pcs grounding module - 8pcs BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

21 TERMINAL DISTRIBUTION BOX 8-10 M The Terminal Distribution Box 8"- 10"M is used to connect terminal devices by the distributing telecommunication network with the exchange. It is designed to be used for outdoor ( facades of buildings or poles ) and indoor mounting. The body ( body and cover ) is made of incombustible polycarbonate. The box is equipped with a back mount frame ( channel ) to 2 modules QC "Borima". Each box TB 8" - 10"M is equipped with: modules QC; back mount frames ( channels ) for modules QC; grounding bridge with a clip and a cable shoe; rubber sealing with an input and output openings - 3 pcs; hermetic rubber sealing between the body and the cover; clamp for supporting the incoming cable - 2 pcs; a kit of screws, washers and pins for outdoor and indoor mounting; a special bolt for closing the box. BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

22 TDB 8 10 M TECHNICAL DATA Height H, mm 173 Width W, mm 131 Depth D, mm 76 Weight 8 M; 10 M, kg 0.450; Inputs / Outputs: 3 rubber seal with possibility for: -2pcs input opening for 10 cable; -15 pcs output openings for one pair cable; - grounding cable Material of the box polycarbonate glass - filled Material of the module polycarbonate glass - filled Colour light - grey, RAL 7035 Flammability class VO to UL 94 Relative humidity to 100% Environment - 45 to +75 C temperature Part No Type Description Equipment 8265 TDB 8"M Terminal distribution box for 8 with backmount frame for 2 modules connection, disconnection - 1pc Grounding module - 1pc 8266 TDB 10"M Terminal distribution box for 10 with backmount frame for 2 modules connection, disconnection - 1pc Grounding module - 1pc BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

23 TERMINAL DISTRIBUTION BOX M The Terminal Distribution Box M distributes cables of the secondary cable network and subscriber cables of the tertiary cable network. It is designed to be used for mechanical and electrical indoor and outdoor installation (outer walls of buildings and poles). The body (body and cover) is made of incombustible polycarbonate. The box can be eqipped with a back mount frame up to 6 modules QC (Quick Connecting System) Borima. Each box DB M is equipped with: modules- QC (disconnecting or connecting); back mount frame for mounting of modules QC; grounding bridge with a clip and a cable shoe; rubber sealing with 1 inlet and 1 outlet, according to the capacity; cover sealing, made of an air-foamed rubber; supporting bracket of the incoming cable 1 pc; a kit of screws, washers and pins for outdoor and indoor mounting; brackets- 2pcs for mounting on the pole BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

24 TDB M TECHNICAL DATA Height H, mm 325 Height H1, mm 350 Width W, mm 190 Depth D, mm 85 Weight 30 M; 50 M, kg kg kg. Material of the box polycarbonate glass-filled Material of the modules polycarbonate glass-filled Colour light grey, RAL 7035 Flammability class VO to UL 94 Relative humidity to 100% Environment temperature - 45 to +75 C NOTE: H Height of the box without brackets (for mounting on the wall); H1 Height of the box with brackets (for mounting on the pole). Part No Description Specification Equipment with modules QC TDB 30 M TDB 50 M Terminal Distribution Box with capacity from 30 up to 50 and back mount frame for modules Connection, disconnection according the capacity Grounding module 1pc. BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

25 TERMINAL DISTRIBUTION BOX M The Terminal Distribution Box M distributes the cables of the secondary cable network and the subscriber cables of the tertiary cable network. It is designed to be used for mechanical and electrical indoor and outdoor installation. The body (body and cover) is made of incombustible polycarbonate. The box can be equippted with a back mount frame up to 11 modules QC (Quick Connecting System) Borima Each box TB M is equipped with: modules QC (disconnecting or connecting); back mount frame for mounting of modules QC; grounding bridge with a clip and a cable shoe; rubber sealing with 1 inlet and 2 outlets, according to the capacity; cover sealing, made of air-foamed rubber; supporting bracket of the incoming cable 1 piece; a kit of screws, washers and pins for outdoor and indoor mounting; a special bolt for shutting the box BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

26 TDB M TECHNICAL DATA Height H, mm 410 Height H1, mm 430 Width W, mm 210 Depth D, mm 100 Weight 70 M; 100 M, kg kg kg. Material of the box polycarbonate glass-filled Material of the modules polycarbonate glass-filled Colour light grey, RAL 7035 Flammability class VO to UL 94 Relative humidity to 100% Environment temperature - 45 to +75 C NOTE: H Height of the box without brackets (for mounting on the wall); H1 Height of the box with brackets (for mounting on the pole). Part No Description Specification Equipment with modules QC TDB 70 M TDB 100 M Terminal Distribution Box with capacity from 70 up to 100 and back mount frame for modules Connection, disconnection according the capacity Grounding module 1pc. BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

27 PLASTIC TELECOMMUNICATION CABLE CHUTE The Plastic chute of telecommunications cables is designed to be used for underground cable lines. Inside the chute can be mounted mechanical, heat shrinkable or optical closures. It is used for storing of cable reserve too. They are suitable for mounting around an existing cable because of the need of a future repair or insurance of diversion without cutting the cable. Construction: Upper and lower shell with four entrances. There is a rubber sealing fixed on the lengthwise of the lower shell. Universal adapters - 2 pcs. specially designed for mounting of HDPE pipe with a diameter of 32 mm and 40 mm for optical cables; Closing entrance - 2 pcs. Conical deaf entrances are used for sealing of the unused entrances; Metal supporting frame The Shells are mounted with stainless screwed connections. BORIMA - EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

28 PLASTIC TELECOMMUNICATION CABLE CHUTE Part No 8443 Material upper and lower shell Colour Universal adapters Bolt connections Support frame Colour They are made of polypropylene with 30% glass Yellow, RAL 1018 Polypropylene Stainless steel Steel with powder coating Grey RAL 7035 Mechanical stability - Loading (5 min) - Hit (10 times) - Hit (1 time) Tightness with universal adapters Weight Technical data -16 kn over the whole surface of the chute - 6 kg guillotine, falling from 90 cm. height to the center of the chute - 7 kg device with point hit, falling from 80 cm height, depth entering 20mm to the center of the chute Average tightness Round 27 kg. A complete set of a chute No Description Piece per set 1 Upper shell 1 2 Lower shell 1 3 Metal support frame 1 according to the customer request 4 Universal adapters - set 2 - set of rubber seals - rubber entrance 32 and 40 5 Plug-up entrance 32 and Protection gel 1 7 Cleaning tissue 2 8 Protective covers 1 kit 9 Screwed connections 1 kit 10 Seal rubber for replacement - 4 m and adhesive according to the customer request BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

29 MECHANICAL AND FIBER-OPTIC CLOSURES Mechanical and fiber optic closures, serve for protection of connections in non-pressurized networks. Fits different types of cables: Telecommunications - Plastic coated copper cables; - Fiber optic cables / for closure type MAM /. Electric/power cables - Up to 1000 Volt Benefits: Quick and easy installation; No special tools needed; For multiple use; For aerial and underground installations. One closure kit consists of two symmetrical half-shells with a foamed rubber length seal fixed in the top shell / excluding FDM1 and FDM2, where the design is type Jar /. Entry seals keep the closure absolute watertight. The shells are screwed together with nuts and bolts, made of stainless steel. BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

30 MECHANICAL IN LINE CLOSURE FOR CONVENTIONAL COPPER CABLES TYPE MVM One closure kit consists of: Two symmetrical half-shells, made of material polypropylene - colour yellow (RAL1023); Foamed rubber length seal of the shell; Rubber seals between the two halves at closure installation; Bolt splices for mechanical connection of the shells; Cable holders Types: In-Line mechanical closure MVM 23 / suitable for 2 pcs. of cable with diameter up to 23 mm; Part No Type of the closure Max. number pair Outer diameter of the cable Splice opening length (mm) Dimension of the closure D x W x H 8360 MVM 23/ BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

31 MECHANICAL BRANCH-OFF CLOSURE TYPE MAM FOR CONVENTIONAL COPPER CABLES AND OPTICAL FIBERS One closure kit is the same as the In-Line closure type MVM Type MAM is with two entrances and with two outlets. Types: Mechanical Branch-off closure type MAM 23 / suitable for 4 pcs of cable with diameter up to 23 mm Part No Type of the closure Max. number pair Outer diameter of the cable Splice opening length (mm) Dimension of the closure D x W x H / BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

32 MECHANICAL CLOSURE TYPE FDM The closures type FDM are type Jar for making of In-Line and Branch-off connections One closure kit consists of: Body - made of material polypropylene Cover - made of material polypropylene - black ( RAL 8022 ); Rubber seal; Former (schablone) and keys (for FDM 2). Types: Mechanical closure FDM 1 - suitable for 4 pcs of cable from 6 to 14 mm Mechanical closure FDM 2 - suitable for 4 pcs of cable from 6 to 25 mm Part No Type of the closure Max. number pair Outer diameter of the cable (mm) Splice opening length (mm) Dimension of the closure ( x L) 8362 FDM x x FDM x x 280 BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

33 FIBER OPTIC CLOSURE 23 / 200 F The fiber optic closure is designed to connect optical cables with metal elements or dielectric in the following cases: In Line and In Line Branch off closure - 1 : 1; 1 : 2; 1 : 3 at maximum 8 pcs of cassettes for organization of the welding; End closure - 1 : 1 to 1 : 2; Branched-Transit closure - 1 : 1; 1 : 2 (without cutting-off the base cable). The closure is designed for optical cables with outer diameters from 6 to 23 mm. Installation: At environment temperature -from - 5 C to +50 C and relative humidity to 98 % without condense humidity. Part No with / without heat shrinkable splice protection 8353 / / / / 8356 Type of the closure 23/ 200 FO - 12 fibers 23/ 200 FO - 24 fibers 23/ 200 FO - 48 fibers 23/ 200 FO - 72 fibers Fiber optic splice cassette Outer diameter of the cable Splice opening length (mm) Dimension of the closure D x W x H BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

34 METAL NICHE TYPE CABINET Distribution Metal Niche (Type Cabinet) The Distribution Metal Niche is designed to be used for indoor telephone installations, located in buildings and it connects the incoming cable from the cable network with terminal devices. The Distribution Metal Niche is made of metal sheets with thickness 1.5 mm; The Coating is powder painted with colour RAL 7035 or according to the request of the customer; Types: - with one door; - with two doors; They are equipped with safety locks with one and the same combination. BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

35 METAL NICHE TYPE CABINET TECHNICAL DATA Part No H, mm W, mm D, mm According to an order they can be produced with dimensions specified by the customer. The Equipment chrome-nickel back mount frames for modules type Borima or according to the order of the customer. BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

36 GROUNDING KITS series SG Grounding kits series SG are designed to meet the most severe grounding system requirements for wireless communication systems. A well designed transmission line system uses grounding kits to provide a bond between the cable and the tower / earth ground system to protect radio components from lightning transients. One grounding kit is recommended at tower top, tower bottom, at 200 ft (60 m) intervals (where applicable), and at the entrance to the equipment shelter. Grounding kits are designed for fast, easy installation on coaxial cable. They utilize a copper clip for easy snap-on installation to the cable's outer conductor. A Kit includes: Copper clip, riveted to the grounding wire; Fasteners for fixing to the tower; Two-part weatherproofing tapes. BORIMA -EAD; Tel.: 359//670// ; Fax: 359//670// ; office@borima-bg.com

37 GROUNDING KITS series SG Characteristics Material Clip Bail Rivets Cable shoes Bonding Conductor Copper Stainless Steel Copper Tin Plated Copper 7-Strand Copper Wire Cross-Sectional Area 16 2 Mechanical Part No Fits cable diameters According customer SG 1/2" mm to mm request According customer SG 7/8" 26.7 mm to 28.7 mm request According customer request SG 1 1/4" 38.4 mm to 40.1 mm 8549 SG 1 5/8" 49.0 mm to 50.8 mm Cable shoes clearance holes 3/8 16 or 10 screws Bail closure force Maximum of 11 kg. Environmental Operating Temperature Storage Temperature Weather Resistant * -45 to +85 Ñ -45 to +85 Ñ Salt Spray, Rain, Ice, Wind, UV * GROUNDING KIT series SG is supplied with weatherproofing material which must be installed properly to insure optimum performance in these conditions. BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

38 FIXING CABLE CLAMPS The fixing cable clamps are used for fixing and strengthening of cables and tubes with different function. They are made of corrosion-proof metal elements and calibrated shells from polyamide, UV and ageing resistant. The protection of the cable or the tube against possible damage is ensured with the help of the strong polyamide shells, combined with tightening bolt. An additional reliable catching achieved, using self-locking nut. They give possibility for installation at: Flat profiles with thickness maximum to 10 mm ( Fig.1); Tubes with diameter maximum to 18 mm ( Fig.2); Metal ropes with diameter maximum to 18 mm ( Fig.3). BORIMA - EAD; Tel.: 359//670// ; Fax: 359//670// ; office@borima-bg.com

39 FIXING CABLE CLAMPS Fig.1 Fig.2 Fig.3 Material Metal part of the clamp Shells Stainless steel Polyamide, black Connecting elements Stainless steel Types: The types are according to the dimensions of the outer diameter of the cable or the tube, which they fix. Part No Single Double Triple Fixing cable clamp According customer 1 request Fixing cable clamp According customer 1 ¼ request Fixing cable clamp According customer request Fixing cable clamp According customer ½ request Fixing cable clamp According customer R 8 request The types are according to the number of cables or the number of tubes, which they fix. Single Double Triple With two polyamide shells With four polyamide shells With six polyamide shells BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

40 TECHNICAL DEVICES FOR MECHANICAL MOUNTING The technical devices for mechanical mounting are used for building and operation of aerial cable communication lines, which are done through communication cables with a self carrying rope. They are made of steel and anti-corrosive coating. Types: Carrier horizontal for concrete poles; Carrier horizontal for wooden poles; Tie-bar with thread M8; M10; M12; Carrier transitional 16; Clamp three layered; Clamp transitional 5.5; Clamp transitional 7. BORIMA - EAD; Tel. : 359//670// ; Fax: 359//670// ; office@borima-bg.com

41 TEHNICAL DEVICES FOR MECHANICAL MOUNTING The technical devices for mechanical mounting Carrier horizontal for concrete poles Part No Carrier horizontal for wooden poles Part No Carrier transitional 16 Part No L, mm N, mm ±2 206 ± ±2 305 ±1 Tie-bar with thread 8; 10; 12 Part No according customer request L min max D R Clamp three layered Part No Clamp transitional 5.5 Part No Clamp transitional 7 Part No BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

42 ROLL LINEAR Roll linear is used for mechanical laying of the cables at building of cable traces. It assists the cables stringing for getting of their maximum permissible length and the usage of minimum number of joint closures. It is made of polyamide. The roll linear consists of: A base made of polyamide, on which there are four openings for fixing to a foundation. A roll fixed with a shaft and bearings to the base. BORIMA - EAD; Tel. : 359//670// ; Fax: 359//670// ; office@borima-bg.com

43 ROLL LINEAR Part No 8449 Base Roll MATERIAL Polyamide, white Polyamide, white TECHNICAL DATA Height, mm 190 Width, mm 218 Length, mm 277 Environment temperature -40 to +70 Ñ BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

44 METAL BOXES The metal boxes can be used according to the needs of the customers. They are made of sheet material with thickness from 1 to 1.5 mm. The thickness of the sheet material and overall dimensions of the boxes can be manufactured according to customers' request. The coating is made of powder painting with a colour in compliance with the customers' request. They are equipped with secret locks. BORIMA - EAD; Tel. : 359//670// ; Fax: 359//670// ; office@borima-bg.com

45 METAL BOXES Part No H, W, D, mm mm mm BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

46 TERMINAL FIBER OPTIC BOX The Terminal Fiber Optic Box serves to organize and protect the fiber optic cable joints from dust and mechanical damages. The design allows easy access to all joints and connections. It is made of metal sheets with 0.8 mm thickness. The coating is powder paint - color is according to customer's request. The Terminal Fiber Optic Box is designed for four pieces of optical fibers. The Terminal Fiber Optic Box consists of: Body ; Cover; The Terminal Fiber Optic Box can be made with or without equipment. The equipment includes: Heat shrinkable protective sleeve Holder 1 piece; SC duplex adapter 2 pieces; Connectors 2 pieces; Heat shrinkable protective sleeves 4 pieces; The Terminal Fiber Optic Box's dimensions and type of equipment can be made according to customer's request. BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

47 TERMINAL FIBER OPTIC BOX Part No W, mm W 1, mm H, mm D, mm BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com

48 ODF DISTRIBUTOR ODF Distributor serves to organize and protect fiber optic connections from dust and mechanical damages. The design allows easy access to all connections and joints. It is made of metal sheets with 1 mm thickness. The coating is powder paint - color is according to customer's request. Types of ODF Distributors according to their capacity. For 12 optical fibers; For 24 optical fibers; For 48 optical fibers; For 96 optical fibers; ODF Distributor consists of : Body ; Cover; Locks 2 pieces - according to customer's request; Leads - according to customer's request. ODF can be made with or without equipment. The equipment includes: Splice cassettes - their number depend on the capacity; SC duplex adaptor - the number depends on the capacity; Connectors - the number depends on the capacity; Heat shrinkable protection sleeves - the number depends on the capacity; The ODF - Distributor's dimensions and type of equipment can be made according to customer's request. BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

49 ODF DISTRIBUTOR Part No Type H,mm 8498 ODF ODF ODF ODF ODF ODF BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

50 WALL TELECOMMUNICATION CABINET 6 U The Wall Telecommunication Cabinet 6U is designed for installation of 6 ODF distributors. The Wall Telecommunication Cabinet 6U consists of: Assembly Columns mm sheet steel; Upper and Lower Panels mm sheet steel; Side opening Panels mm sheet steel; Rear Panel mm sheet steel; Door metal frame made of plexiglas or sheet steel 1.2 mm ; 19 mounting rail - two pieces, 1.2 sheet steel; Safety lock; The coating is powder paint and color is according to customer's request. It is designed for indoor installation. There is a possibility for a fan to be mounted inside the Cabinet. The design allows easy access to all ODF distributors. The Wall Telecommunication Cabinet can be made to 45 U according to customer's request. BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

51 WALL TELECOMMUNICATION CABINET 6 U Part No W, mm H, mm D, mm BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

52 FIBER OPTIC CLOSURE The Fiber Optic Closure is designed to provide protection for all types of joints of fiber optic cables from mechanical effects and environment influences. The closure may be used in underground, buried, ground or aerial installation. The fiber optic closure consists of: A Body - made of polyamide; A Base with four round and one oval entry port - made of polyamide; Closing clamp which is easy to work with when you open and lock the closure - made of polyamide; Holder for splice cassette - made of polyamide; Splice cassette and cover - made of ABS ; Rubber sealing ring placed between the body and base; The types of Fiber Optic Closure are according to their capacity: For 12 optical fibers; For 24 optical fibers; For 48 optical fibers; For 96 optical fibers; Equipment: Heat shrinkable protective sleeves - their number depends on the capacity, they serve to protect the joint optical fibers; Heat shrinkable sleeve - 5 pieces, which seals the incoming cables; Branch-off clip - 1 piece is used for branching cables; Aluminium foil; Spanner; Grounding cable; Pig tails; Metal Holder - 1 piece is used for ground closure installation ; BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

53 FIBER OPTIC CLOSURE The closure is designed for fiber optic cables with outer diameter up to 18 mm. The closure is made of black impact resistant polyamide and flammability class V0 in compliance with UL 94. Installation: When the temperature of the environment is from - 5 C to +50 C and relative humidity is to 98 % condensed moisture. Part No Type of Closure Number of cassettes for optical fibers 8315 For 12 optical fibers For 24 optical fibers For 48 optical fibers For 96 optical fibers 4 BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

54 BRANCH OFF KIT FOR CABLE BRANCHING SYSTEM (BOKT) Branch off kits are designed for branching cables of heat shrinkable closures. The three types of Branching kits (BOKT) cover all sizes of cables. Three-finger construction helps in perfect branching and reliable sealing, as the middle finger is coated with hot melt adhesive. It is supplied in kit form with all necessary components for branching. One Branching kit (BOKT) is required for branching two cables at one end. The KIT contains: Branch off clip Cleaning tissue Aluminium cable foil Shield continuity wire Abrasive strip Types: Two-finger clip Three-finger clip Medium Three-finger clip Small BORIMA - EAD; Tel. : 359//670// ; Fax: 359//670// ; office@borima-bg.com

55 BRANCH OFF KIT FOR CABLE BRANCHING SYSTEM (BOKT) Branch off kits Types The two-finger clip consists of two details with teeth in their joint parts. It is made of polyamide. Part No Three-finger clip Medium is made of aluminium alloy and it is with epoxy-polyester coating. The middle finger is coated with hot melt adhesive. Part No Three-finger clip Small is made of aluminium alloy and it is with epoxy-polyester coating. The middle finger is coated with hot melt adhesive. Part No BORIMA - EAD; tel.: 359//670// ; fax: 359//670// ; office@borima-bg.com

56 TELEPHONE BOOTH The Telephone Booth is designed for mounting telephones sets and as advertising facility. There is a possibility for setting two telephones on left or right side, in accordance with the requirements of the customer. On the Telephone Booth there is also an advertising part on which can easily be put and respectively replace advertising posters. The advertising part is lit up by light-emitting diodes (LED). It is made of section steel with hot galvanized coating. It is painted in accordance with the requirement of the customer. It is mounted on reinforced concrete foundation. BORIMA -EAD; tel. 359//670// ; fax 359//670// ; office@borima-bg.com

57 TELEPHONE BOOTH H, W, D, Part No mm mm mm BORIMA - EAD; tel.359//670// ; fax 359//670// ; office@borima-bg.com