DirectPort Product Family Multi-port Serial Cards Hardware User Guide

Transcription

1 DirectPort Product Family Multi-port Serial Cards Hardware User Guide Rev.0.0 Sena Technologies, Inc.

2 Copyright Copyright 00, Sena Technologies, Inc. All rights reserved. Sena Technologies reserves the right to make changes and improvements to its product without providing notice. Trademark Windows is a registered trademark of Microsoft Corporation. Notice to Users When a system failure may cause serious consequences, protecting life and property against such consequences with a backup system or safety device is essential. The user agrees that protection against consequences resulting from system failure is the user s responsibility. This device is not approved for life-support or medical systems. Changes or modifications to this device not explicitly approved by Sena Technologies will void the user s authority to operate this device. Precautions and Safety Do not drop or subject the device to impact. Damage to your products may result from improper use. Keep away from harsh environments including humid, dusty, and smoky areas. Damage to your products may result from improper use. Do not attempt to disassemble the device. Damage to your products may result from improper use. Do not place heavy objects on the product. Damage to your products may result from improper use. Contact Information Technical support support@sena.com Company website:

3 Contents Introduction. About This Document. DirectPort Product Family. Product Specifications DirectPort UPCI. DB Pin Assignments. Cabling.. Connecting Terminal.. Connecting Modem DirectPort UPCIB. DB Pin Assignments. Jumper Settings.. RS/RS Selection.. Termination Resistance Selection.. Slew Rate Limit Ability. Cabling.. RS Point-to-Point Connection.. RS Multi-Drop Connection.. RS Connection DirectPort UPCI. DB Pin Assignments. Cabling.. Connecting Terminal.. Connecting Modem DirectPort UPCIB. DB Pin Assignments. Jumper Settings.. RS/RS Selection.. Termination Resistance Selection.. Slew Rate Limit Ability. Cabling.. RS Point-to-Point Connection.. RS Multi-Drop Connection.. RS Connection

4 DirectPort UPCISP. DB Pin Assignments. Cabling.. Connecting Terminal.. Connecting Modem DirectPort UPCIBSP. DB Pin Assignments. Jumper Settings.. RS/RS Selection.. Termination Resistance Selection.. Slew Rate Limit Ability. Cabling.. RS Point-to-Point Connection.. RS Multi-Drop Connection.. RS Connection DirectPort UPCILP. DB Pin Assignments. Cabling.. Connecting Terminal.. Connecting Modem DirectPort UPCIBLP. DB Pin Assignments. Jumper Settings.. RS/RS Selection.. Termination Resistance Selection.. Slew Rate Limit Ability. Cabling.. RS Point-to-Point Connection.. RS Multi-Drop Connection.. RS Connection 0 Regulatory Information 0. FCC Compliance Statement 0. CE Declaration of Conformity

5 Introduction. About This Document This document describes the hardware specifications and the cabling guide of the DirectPort universal PCI multiport serial cards. For software and driver installation, please refer to the Software User Guide in the CD included. You can also download documents including this document and the Software User Guide from Sena Technologies home page at DirectPort Product Family The DirectPort product family of universal PCI multiport serial cards is designed to provide flexible expansions of high performance serial ports to the computers to meet the diverse and unique requirements easily and cost-effectively. The DirectPort universal PCI multiport serial cards are based on the PCI Local Bus Spec.. They automatically set the I/O addresses and the IRQ numbers when ROM bios or the operating system starts. All DirectPort serial cards support high speed serial speed up to. Kbps and are equipped with internal surge protection for maximum reliability. They also have internal byte deep FIFO for communication stability. The DirectPort product family provides the wide range of hardware combinations. Users can select different port counts among, and ports, different line interface between RS and RS/, and different form factor between standard profile and low profile, to meet their specific hardware requirements. The DirectPort product family also supports various OS s including Windows 000/XP/Vista/ and major Linux distributions to meet today s various software environments.

6 . Product Specifications UPCI UPCIB UPCI UPCIB UPCISP UPCIBSP UPCILP UPCIBLP Serial Ports Line Interface RS RS/ RS RS RS/ RS RS RS/ RS RS RS/ RS Form Factor Serial Speed BUS Interface UART Controller Connector I/O Address IRQ Number Surge Protection Supported OS Approvals Warranty Low Profile/Standard Profile Standard Profile Low Profile Up to. Kbps PCI Local Bus Spec. C0 Compatible DB Male Automatic Configuration Automatic Configuration ±KV Windows 000/XP/00/Vista/00/, Linux FCC, CE -Year Limited Warranty

7 DirectPort UPCI. DB Pin Assignments RS RI DB Male. Cabling.. Connecting Terminal DB TERMINAL () () () (0) () () () () When only pin No.,,(,,) are informally used connect -(-) and -(--0) in a loopback type repectively. (Parenthesized pin number is applied for pin terminal).. Connecting Modem RI DB Modem 0 RI

8 DirectPort UPCIB. DB Pin Assignments RS RS T T DB Male DB Male. Jumper Settings.. RS/RS Selection : Set RS Interface : Set RS Interface INTERFACE INTERFACE

9 .. Termination Resistance Selection : Set RS Termination Resistor : Set RS Termination Resistor None: Do not set Termination Resistor NONE NONE NONE.. Slew Rate Limit Ability 0M: Not use Slew Rate Limit ability. Maximum communication speed.kbps in this mode. 0M 0K 0K: Use Slew Rate Limit ability. Communication speed is limited under 0Kbps. 0M 0K

10 Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode. Cabling.. RS Point-to-Point Connection Host Terminal.. RS Multi-Drop Connection Host Terminal Terminal.. RS Connection Terminal Terminal Terminal RT T RT T T T T T RT: 0 Ohm (Not necessary when there is not much noise) RS, like LAN, uses Half Duplex Bus and has no classification between host and terminal 0

11 DirectPort UPCI. DB Pin Assignments RS RI DB Male. Cabling.. Connecting Terminal DB TERMINAL () () () (0) () () () () When only pin No.,,(,,) are informally used connect -(-) and -(--0) in a loopback type repectively. (Parenthesized pin number is applied for pin terminal).. Connecting Modem RI DB Modem 0 RI

12 DirectPort UPCIB. DB Pin Assignments RS RS T T DB Male DB Male. Jumper Settings.. RS/RS Selection : Set RS Interface : Set RS Interface INTERFACE INTERFACE

13 .. Termination Resistance Selection : Set RS Termination Resistor : Set RS Termination Resistor None: Do not set Termination Resistor NONE NONE NONE.. Slew Rate Limit Ability 0M: Not use Slew Rate Limit ability. Maximum communication speed.kbps in this mode. 0M 0K 0K: Use Slew Rate Limit ability. Communication speed is limited under 0Kbps. 0M 0K

14 Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode. Cabling.. RS Point-to-Point Connection Host Terminal.. RS Multi-Drop Connection Host Terminal Terminal.. RS Connection Terminal Terminal Terminal RT T RT T T T T T RT: 0 Ohm (Not necessary when there is not much noise) RS, like LAN, uses Half Duplex Bus and has no classification between host and terminal

15 DirectPort UPCISP. DB Pin Assignments RS RI DB Male. Cabling.. Connecting Terminal DB TERMINAL () () () (0) () () () () When only pin No.,,(,,) are informally used connect -(-) and -(--0) in a loopback type repectively. (Parenthesized pin number is applied for pin terminal).. Connecting Modem RI DB Modem 0 RI

16 DirectPort UPCIBSP. DB Pin Assignments RS RS T T DB Male DB Male. Jumper Settings.. RS/RS Selection : Set RS Interface : Set RS Interface INTERFACE INTERFACE

17 .. Termination Resistance Selection : Set RS Termination Resistor : Set RS Termination Resistor None: Do not set Termination Resistor NONE NONE NONE.. Slew Rate Limit Ability 0M: Not use Slew Rate Limit ability. Maximum communication speed.kbps in this mode. 0M 0K 0K: Use Slew Rate Limit ability. Communication speed is limited under 0Kbps. 0M 0K

18 Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode. Cabling.. RS Point-to-Point Connection Host Terminal.. RS Multi-Drop Connection Host Terminal Terminal.. RS Connection Terminal Terminal Terminal RT T RT T T T T T RT: 0 Ohm (Not necessary when there is not much noise) RS, like LAN, uses Half Duplex Bus and has no classification between host and terminal

19 DirectPort UPCILP. DB Pin Assignments RS RI DB Male. Cabling.. Connecting Terminal DB TERMINAL () () () (0) () () () () When only pin No.,,(,,) are informally used connect -(-) and -(--0) in a loopback type repectively. (Parenthesized pin number is applied for pin terminal).. Connecting Modem RI DB Modem 0 RI

20 DirectPort UPCIBLP. DB Pin Assignments RS RS T T DB Male DB Male. Jumper Settings.. RS/RS Selection : Set RS Interface : Set RS Interface INTERFACE INTERFACE 0

21 .. Termination Resistance Selection : Set RS Termination Resistor : Set RS Termination Resistor None: Do not set Termination Resistor NONE NONE NONE.. Slew Rate Limit Ability 0M: Not use Slew Rate Limit ability. Maximum communication speed.kbps in this mode. 0M 0K 0K: Use Slew Rate Limit ability. Communication speed is limited under 0Kbps. 0M 0K

22 Slew Rate Limit reduces reflected waves emitting from ends of communication cables and speeds up slew-rate driver that restrains EMP electromagnetic waves thereby enabling communication with no data errors. But communication speed is limited in this mode. Cabling.. RS Point-to-Point Connection Host Terminal.. RS Multi-Drop Connection Host Terminal Terminal.. RS Connection Terminal Terminal Terminal RT T RT T T T T T RT: 0 Ohm (Not necessary when there is not much noise) RS, like LAN, uses Half Duplex Bus and has no classification between host and terminal

23 0 Regulatory Information 0. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 0. CE Declaration of Conformity We, Sena Technologies, Inc., declare that the product(s): DirectPort UPCI -Port RS Serial Card DirectPort UPCIB -Port RS/ Serial Card DirectPort UPCI -Port RS Serial Card DirectPort UPCIB -Port RS/ Serial Card DirectPort UPCISP -Port RS Serial Card DirectPort UPCIBSP -Port RS/ Serial Card DirectPort UPCILP -Port RS Low Profile Serial Card DirectPort UPCIBLP -Port RS/ Low Profile Serial Card to which this declaration relates is in conformity with the following standard(s) or other normative document(s) EN 0: 00 EN000--: +A:00, +A:00 EN0: +A:00, +A:00 following the provisions of EMC DIRECTIVE 00/0/EC

24 Sena Technologies, Inc.