EE210. Humidity and Temperature Transmitter for Demanding Climate Control Applications. Features. Applications

Transcription

1 EE210 Features Appropriate for US mounting requirements» Knockout for ½ conduit fi tting External mounting holes» Mounting with closed cover» Electronics protected against construction site pollution» Easy and fast mounting Electronics on the underside of the PCB» Optimum protection against mechanical damage during installation Bayonet Screws» Open/closed with a ¼ rotation T: (+34) Humidity and Temperature Transmitter for Demanding Climate Control Applications The EE210 transmitter by E+E Elektronik meets the highest requirements in demanding climate control applications. Besides highly accurate measurement of relative humidity and temperature, EE210 calculates dew point temperature, absolute humidity and mixing ratio. EE210 is available as wall or duct mounted as well as with remote probe. The enclosure minimizes installation costs and provides outstanding protection against contamination and condensation. All measured and calculated values are available on the BACnet MS/TP or Modbus RTU interface; two of the measured and calculated values are available on the analogue voltage or current outputs, while up to three values can be shown simultaneously on the optional display. Excellent performance of EE210 in polluted, aggressive environment is EE210 ensured by the combination of completely protective encapsulated measurement electronics inside the sensing probe and the long-term stable HCT01 sensor with E+E proprietary coating. With an optional confi guration kit the user can set the Modbus interface parameters, the output scaling and perform one or two point adjustment for humidity and temperature. Display» Selectable display layout» Measurands freely selectable Smooth cover surface» No accumulation of dust in protruding edges IP65 / NEMA 4 Enclosure Cast Electronics» Mechanical protection» Condensation-resistant Watertight cable outlet E+E Humidity sensor HCT01» Long-term stability» Protected RH sensor surface» Protected solder pads» Tested according to automotive standard AEC-Q200 Applications agriculture stables, incubators, hatchers green houses storage rooms, cooling chambers indoor pools demanding climate control BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI. 4 v2.1 / Modification rights reserved EE210

2 T: (+34) Technical Data Measured Values Relative Humidity (RH) Sensor E+E Sensor HCT01-00D Working range % RH RH accuracy (incl. hysteresis, non-linearity and repeatability) Wall & duct version: C ( F) 90% RH ±( *measured value) % RH C ( F) >90% RH ± 2.3% RH C ( F) ±( *measured value) % RH Remote probe version at 20 C (68 F) ±2.5% RH Temperature (T) S ensor Pt1000 (tolerance class B, DIN EN 60751) integrated in HCT01 T-accuracy wall & duct remote probe C C C C Outputs Analog output 0-5 V / 0-10 V -1 ma < I L < 1 ma (RH: %; T: see ordering guide) 4-20 ma (two-wire) R L 500 Ohm Digital output RS485 (BACnet MS/TP or Modbus RTU), max. 32 EE210 in one bus General Power supply for 0-5 V / 0-10 V / RS V DC 1) or 24V AC ±20% for 4-20 ma 10V + RL x 20 ma < V+ < 30V DC Current consumption Voltage output DC supply typ. 3.3mA; with display typ. 3.6mA AC supply typ. 34mA; with display typ. 37mA Current output DC supply max. 40mA Digital interface DC supply typ. 5mA; with display typ. 19mA AC supply typ. 52mA; with display typ. 118mA Display 1, 2 or 3 lines, user configurable Connection Screw terminals, max. 1.5 mm 2 Housing material Polycarbonate, UL94V-0 (with Display UL94HB) approved Protection class IP65 / NEMA 4 Cable gland M16 x 1.5 Probe cable (type C) PVC, Ø 4.3mm, 4 x 0.25 mm 2, Length: 1.5 or 3m (4.9 or 9.8ft) Sensor protection E+E Coating Electromagnetic compatibility EN EN Industrial Environment Temperature ranges Operating: C ( F) ( C for remote probe EE210P) Storage: C ( F) Temperature ranges with display Operating: C ( F) ( C for remote probe EE210P) Storage: C ( F) 1 USA & Canada: class 2 supply required, max. supply voltage 30V EE210 v2.1 / Modification rights reserved 5

3 T: (+34) Dimensions (mm/inch) Typ A Typ B 90 ±0.3 mm 3.54 ± mm 1.81 FOR CONDUIT INSTALLATION 90 ±0.3 mm 3.54 ±0.11 Ø > 13mm Ø > mm mm 3.17 L...according to ordering guide 101mm 3.98 GASKET ~55mm ~2.16 CABLE GLAND M16x1.5 19mm 0.75 Typ C Ø 12mm Ø ±0.3 mm 2.36 ± mm 4.17 EE210P 34mm 1.34 Ø > 16mm Ø > mm 0.24 Connection Diagram EE210-HT VDC 24VAC ±20% EE210-HT VDC VDC 24VAC RL<500 ±20% Ohm VDC RL<50 Ohm Output: 0...5V V Output: mA EE210-HTx VDC 24VAC ±20% EE210P remote probe (for HT6/HTx3) Output: Modbus RTU or BACnet MS/TP 6 v2.1 / Modification rights reserved EE210

4 T: (+34) Ordering Guide MODEL ANALOGUE 1) DIGITAL 1) HOUSING TYPE PROBE LENGTH 3) DISPLAY 4) FILTER (Type A and B) humidity + (HT) 0-5V (2) RS485 (3) standard (P) wall mount (A) 50mm (1.97 ) (B) display (D) membrane (B) temperature 0-10V (3) none (x) duct mount (B) 200mm (7.87 ) (F) none (x) stainless steel sintered (D) 4-20mA (6) remote probe (C) 2) Type A and C (x) for type C (x) none (x) EE210- Analogue outputs setup OUTPUT 1 SCALING 1 6) OUTPUT 2 SCALING 2 6) UNIT relative humidity 5) (Uw) (002) relative humidity 5) (Uw) (002) metric (M) temperature (Tx) (003) temperature (Tx) (003) non-metric (N) dew point temperature (TD) (004) dew point temperature (TD) (004) frost point temperature (TF) (005) frost point temperature (TF) (005) water vapour partial pressure 5) (Ex) (076) water vapour partial pressure 5) (Ex) (076) mixing ratio 5) (Rx) (083) mixing ratio 5) (Rx) (083) absolute humidity 5) (DV) absolute humidity 5) (DV) specific enthalpy 5) (Hx) specific enthalpy 5) (Hx) Digital output setup 7) PROTOCOL BAUDRATE PARITY STOPBITS UNIT Modbus RTU 7) (1) 9600 (A) odd (O) 1 stopbit (1) metric (M) BACnet MS/TP 8) (3) (B) even (E) 2 stopbit (2) non-metric (N) (C) no parity (N) ) (D) ) (E) ) (F) Remote probe for EE210 Type C: MODEL CABLE LENGTH FILTER humidity + temperature (HT) 1.5 m (4.9 ft) (C) membrane (B) 3 m (9.8 ft) (E) stainless steel sintered (D) EE210P- 1) A combination of analog and digital version is not possible 2) The EE210P probe has to be ordered as seperate position; available for 4-20mA and RS485 versions 3) Selectable probe lenght only for duct mount version available; see dimensions 4) Factory setup: For analogue output versions the display shows the measurands selected for output 1 and output 2. For digital output versions the display shows RH and T 5) Factory Scaling relative humidity % RH water vapour partial pressure mbar 0...3psi mixing ratio g/kg gr/lb absolute humidity g/m³ gr/ft³ specific enthalpy kJ/kg BTU/lb Order Examples Type A and B EE210 EE210-HT3xPAxxB-UwTx005M Model: Humidity+Temperature Transmitter Analog output: 0-10V Housing: standard Type: wall mount Display: none Filter: membrane Output scaling 1: Scaling 1: Output scaling 2: Scaling 2: Unit: Accessories v2.1 / Modification rights reserved relative humidity % RH temperature C metric Product configuration adapter Product configuration software Power supply adapter 6) For Tx, TD und TF; other scaling upon request 7) Modbus Map and setup instructions: See User Guide and Modbus Application Note at 8) Product Implementation conformance Statement (PICS) availbale at 9) Only for BACnet Type C Position 1: EE210-HT6xPCxxx-UwTx005M Model: Humidity+Temperature Basic Device Analog output: 4-20mA Housing: standard Type: remote probe (Pos. 2) Display: none Output scaling 1: Scaling 1: Output scaling 2: Scaling 2: Unit: Position 2: EE210P-HTCB Model: Cable length: Filter: see data sheet EE-PCA EE-PCS (free download: V03 (see data sheet Accessories) relative humidity % RH temperature C metric Humidity+Temperature Probe 1.5 m membrane 7

5 T: (+34) Scope of supply Model EE210 Wall mount (Type A) EE210 Duct mount (Type B) EE210 Remote version (Type C)* EE210-P Remote probe* for Type C Additionally for all EE210 with RS485 interface EE210 according ordering guide Cable gland (2 pcs.) Mounting kit Mounting flange Inspection certificate according to DIN EN Quick Guide - EE210 RS485 Setup * EE210-P is not included in the Scope of Supply of the EE210 Type C 8 v2.1 / Modification rights reserved EE210

6 EE211 The EE211 is dedicated for accurate and long term stable measurement under continuous high humidity (>85 % RH) and condensing conditions in demanding climate control. It features a heated humidity probe and an interchangeable temperature probe. Humidity and Temperature Transmitter for Continuous High Humidity EE211 Excellent performance of EE211 even in polluted, aggressive environment is ensured by the combination of completely encapsulated measurement electronics inside the humidity probe and the long-term stable HCT01 sensor with E+E proprietary coating. The EE211 enclosure is rated IP65/NEMA 4, minimizes installation costs and provides outstanding protection against pollution and condensation. All measured and calculated values are available on the Modbus RTU interface whereas two of the values are available on the analogue voltage or current (3-wire) output. Additionally up to three values can be shown simultaneously on the optional illuminated display. With the optional product confi guration adapter EE-PCA the user can set the Modbus RTU interface parameters, the display format, the measured parameters and the output scaling. Furthermore, the user can perform an one or two point RH and T adjustment. The T probe can also be adjusted separate; for the metal version of the T probe the reference can be a high accuracy dry block calibrator. Features (+34) Opening appropriate for 1/2 US conduit fitting External mounting holes» Mounting with closed cover» Electronics protected against construction site pollution» Easy and fast mounting Display» Shows up to 3 measurands» Backlight Smooth cover surface» No accumulation of dust in protruding edges Electronics on the bottom of the PCB» Optimum protection against mechanical damage during installation IP65 / NEMA 4 Enclosure Cast Electronics» Mechanical protection» Condensation-resistant Bayonet Screws» Open/closed with a ¼ rotation Separate T probe Heated sensing head» Best performance and long term stability under continious high RH and condensing conditions E+E Humidity sensor HCT01» Protected solder pads» Tested according to automotive standard AEC-Q200» Intelligent, interchangeable T probe» Remote connection possible» Calibratable in dry block Protective sensor coating The E+E proprietary sensor coating is a protective layer applied to the active surface of the HCT01 sensing element. The coating extends substantially the lifetime and the measurement performance of the E+E sensor in corrosive environment. Additionally, it improves the sensor s long term stability in dusty, dirty or oily applications by preventing stray impedances caused by deposits on the active sensor surface. 4 v1.0 / Modification rights reserved EE211

7 (+34) Applications Fruit and vegetable storage Cooling, ripening and environmental chambers Green houses and incubators Mushroom industry Operation principle The humidity probe is continuously heated for avoiding condensation and high humidity side effects on the sensing elements, which leads to outstanding long term stability. Based on the measured values humidity and temperature, the EE211 calculates the dew point temperature Td whereas the separate, interchangeable T-probe measures the ambient temperature. Ultimately, out of Td and T, the device calculates the relative humidity RH as well as several other parameters like absolute humidity, mixing ratio, wet bulb temperature or enthalpy. Outstanding long term stability under high humidity conditions The operation principle of EE211 copes with the causes for poor long-term stability of non-heated sensors at continuously high humidity. The constant over-temperature of the EE211 sensing head (approx. 5 C = 9 F) means max. 76 % RH humidity at the sensors and enables following benefi ts: The sensing head of EE211 stays dry even under condensing conditions, which prevents dust and dirt from sticking to the sensor and leads to outstanding long-term stability. The combination of dry sensing head, E+E proprietary coating of the sensing element and sealed solder pads minimize the impact of corrosive agents. Maximum humidity of 76 % RH at the sensor eliminates the drift caused by exposure to continuous high humidity. Important: The humidity related parameters correspond to the location of the T probe. Consequently, the T probe shall be positioned at the place of main interest for RH measurement. In an environmental chamber for instance, the EE211 basic device can be fi xed conveniently on the inside wall, while the T probe can be placed in the middle of the chamber using the optional probe cable. Dimensions (mm/inch) Basic Device: Temperature Probe: 90 ± 0,3 mm mm mm mm 3.98 CABLE GLAND M mm 3.17 Metal Housing EE07-MT Ø12 (0.47 ) 8 (0.3 ) M12x1 50 (2 ) 75 (2.9 ) Ø6 (0.24 ) Polycarbonate Housing EE07-PT6 ~ 55 mm ~2.16 Ø 13 mm Ø (0.3 ) 75 (2.9 ) Ø13 (0.51 ) Ø12 (0.47 ) Ø 12 mm Ø 0.47 M12x1 EE211 v1.0 / Modification rights reserved 5

8 (+34) Connection Diagram EE211-M1J V DC 24 V AC ±20 % EE211-M1A2/3/5/ V DC 24V AC ±20 % Output: Modbus RTU Output: V V ma ma V ma V ma OUT 1 OUT 2 Technical Data Relative Humidity (RH) Sensor E+E Sensor HCT01-00D Working range % RH RH accuracy (incl. hysteresis, non-linearity and repeatability) C ( F) ±( *measured value) % RH Temperature (T) Sensor Pt1000 (tolerance class A, DIN EN 60751) T-accuracy C (at 20 C (68 F) : ±0,1 C) C Outputs Analogue output 0-5 V / 0-10 V -1 ma < I L < 1 ma (RH: %; T: see ordering guide) 0-20 ma / 4-20 ma (3-wire) R L 500 Ohm Digital output RS485, Modbus RTU, max. 32 EE211 in one bus General Power supply V DC 1) or 24 V AC ±20 % Current consumption at 24 V Voltage output DC supply max. 13 ma with display max. 19 ma AC supply max. 38 ma rms with display max. 49 ma rms Current output DC supply max. 34 ma with display max. 40 ma AC supply typ. 75 ma rms with display typ. 85 ma rms Digital interface DC supply typ. 8 ma with display typ. 17 ma AC supply typ. 23 ma rms with display typ. 40 ma rms Display 1, 2 or 3 lines, user configurable, with backlight Connection Screw terminals, max. 1.5 mm 2 Housing material Polycarbonate, UL94V-0 (with Display UL94HB) approved Protection class IP65 / NEMA 4 Cable gland M20 x 1.5 Sensor protection E+E coating Electromagnetic compatibility EN EN , Industrial Environment Temperature ranges Operating / Storage: C ( F) Temperature ranges with display Operating: C ( F) Storage: C ( F) 1) USA & Canada: class 2 supply required, max. supply voltage 30V 6 v1.0 / Modification rights reserved EE211

9 (+34) Ordering Guide EE211 consists of two items to be orders separately: the EE211 basic unit and EE07-xT temperature probe. A third item (T probe extension cable) is optional. Position 1: EE211 Basic Device Hardware Setup - Analogue outputs (not for output J3) Setup - Modbus RTU (only for output J3) EE211 Model humidity + temperature M1 0-5 V A V A3 Output 0-20 ma A ma A6 RS485 J3 none no code Display 1) with backlight D2 Output 1 relative humidity RH % no code other measurand (xx see Measurand Code below) MAxx 0 no code Scaling 1 low 2) value SALvalue 100 no code Scaling 1 high 2) value SAHvalue temperature C no code Output 2 temperature F MB2 other measurand (xx see Measurand Code below) MBxx Scaling 2 low -40 no code value SBLvalue Scaling 2 low 60 no code value SBHvalue 9600 no code Baudrate BD BD7 odd no code Parity no parity PY0 even PY2 Stopbit 1 stopbit no code 2 stopbit BT2 Unit metric-si no code non-metric U2 Measurand Code dew point Td mixing ratio r absolute humidity dv xx C 52 F 53 g/kg 60 gr/lb 61 g/m³ 56 gr/ft³ 57 wet bulb temperature Tw water vapour partial pressure e enthalpy h xx C 54 F 55 mbar 50 psi 51 kj/kg 62 BTU/lb/kg 64 Position 2: EE07-xT Temperature Probe TYPE Polycarbonate - with metal grid filter Metal EE07-PT6 EE07-MT Position 3 (optional): Cable for EE07, M12x1 socket, M12x1 plug TYPE 2 m (6.6 ft) HA m (16.4 ft) HA m ( 32.8 ft) HA ) Factory setup: For analogue output versions the display shows the measurands selected for output 1 and output 2. For digital output versions the display shows RH and T 2) Modbus Map and setup instructions: See User Guide and Modbus Application Note at EE211 v1.0 / Modification rights reserved 7

10 (+34) Order Examples Position 1: EE211-M1A6MB60SBL100SBH300 Model: Humidity+Temperature Output: 4-20 ma Display: none Output scaling 1: relative humidity RH (%) Scaling 1 low: 0 Scaling 1 high: 100 Output scaling 2: mixing ratio r (g/kg) Scaling 2 low: 100 Scaling 2 high: 300 Position 2: EE07-MT Type: Metal Position 1: EE211-M1J3D2BD6U2 Model: Humidity+Temperature Output: RS485 Display: with backlight Baudrate: Parity: odd Stopbits: 1 stopbit Unit: non-metric Position 2: EE07-PT6 Type: Polycarbonate - with metal grid filter Position 3: HA Type: 5 m (16.4 ft) Accessories - Product configuration adapter see data sheet EE-PCA - Product configuration software EE-PCS (free download: - Power supply adapter V03 (see data sheet Accessories) - Protection cap for 12 mm probe HA Metal grid filter cap (HA010106) (see data sheet Accessories) Scope of supply EE211 Basic Device EE211 according ordering guide Cable gland M20 x 1.5 Mounting materials Test report according according to DIN EN User Guide EE07 Temperature Probe EE07 according ordering guide Test report according according to DIN EN Cable for EE07 (optional) 8 v1.0 / Modification rights reserved EE211

11 EE160 Specially designed for HVAC, the EE160 sensor by E+E Elektronik is a costeffective, highly accurate and reliable solution for measuring relative air humidity and temperature. The enclosure minimizes installation costs and provides outstanding protection against contamination and condensation, thus ensuring fl awless operation. T: (+34) Humidity and Temperature Transmitter for HVAC Applications The EE160 employs the new humidity/temperature E+E sensor element HCT01 with excellent long term stability and resistance against pollutants. In combination with a long calibration experience, the EE160 provides a measurement accuracy of ±2.5%RH and is available for wall or duct-mounted with current, voltage BACnet MS/TP or Modbus RTU output. EE160 A confi gurator makes it possible to freely select the scaling of the temperature output and confi gure the Modbus parameters. The confi gurator software, which is free of charge, allows additionally for an on-site adjustment of the humidity and temperature. Appropriate for US mounting requirements» Knockout for ½ conduit fitting External mounting holes» Mounting with closed cover» Electronics protected against construction site pollution» Easy and fast mounting Electronics on the underside of the PCB» Optimum protection against mechanical damage during installation Bayonet Screws» Open/closed with a ¼ rotation IP65 / NEMA 4 Enclosure Cast Electronics» Mechanical protection» Condensation-resistant E+E Humidity sensor HCT01» Long-term stability» Protected RH sensor surface» Protected solder pads» Tested according to automotive standard AEC-Q200 BACnet is a registered trademark of ASHRAE. ASHRAE does not endorse, approve or test products for compliance with ASHRAE standards. Compliance of listed products to the requirements of ASHRAE Standard 135 is the responsibility of BACnet International (BI). BTL is a registered trademark of BI. 10 v2.0 / Modification rights reserved EE160

12 Technical data Measured values Relative Humidity Sensor E+E Sensor HCT01-00D Working range % RH Accuracy at 20 C ±2.5% RH Temperature dependency typ. ±0.03% RH/ C Temperature Sensor Pt1000 (tolerance class B, DIN EN 60751) T-Accuracy at 20 C ±0.3 C Outputs Analog output 0-10 V -1 ma < I L < 1 ma or (RH: %; T: see ordering guide) 4-20 ma (two-wire) R L < 500 Ohm Digital output RS485 (BACnet MS/TP or Modbus RTU) max. 32 EE160 in one bus Passiver T-sensor 4-wire see ordering guide General Power supply for 0-10 V / RS V DC or 24V AC ±20% for 4-20 ma 10V + R L x 20 ma < U V < 35V DC Current consumption Analog with DC power supply typ. 5mA with AC power supply typ. 13mA eff Digital with DC power supply typ. 15mA with AC power supply typ. 25mA eff Connection Screw terminals, max. 1.5 mm 2 Housing material Polycarbonate, UL94V-0 approved Protection class IP65 / NEMA 4 Cable gland M16 x 1.5 Sensor protection membrane filter Electromagnetic compatibility EN EN Temperature ranges Operating temperature: C ( F) Dimensions (mm) Storage temperature: C ( F) T: (+34) ±0.3 mm 3.54 ± ±0.3 mm 3.54 ±0.11 Ø > 13mm Ø > mm 1.81 ~205mm ~ mm mm mm 0.2 GASKET 60 ±0.3 mm 2.36 ±0.11 ~55mm ~2.16 Ø > 16mm Ø > mm mm 0.75 Type A Ø 12mm Ø 0.47 Type B EE160 v2.0 / Modification rights reserved 11

13 T: (+34) Connection diagram EE160-HT3xxx EE160-HT6xxx EE160-HTx3xx T-passive connection for HT3xxx/HT6xxx Ordering Guide Hardware configuration MODEL ANALOG 1) DIGITAL 1) PASSIVE T-SENSOR 2) HOUSING TYPE FILTER humidity + (HT) 0-10V (3) RS485 (3) Pt 100 DIN A (A) polycarbonate (P) wall mount (A) membrane filter (B) temperature 4-20mA (6) none (x) Pt 1000 DIN A (C) duct mount (B) none (x) NTC 10k (E) Ni1000, TK6180 (J) none (x) EE160- Analogue outputs setup OUTPUT SCALING SCALING 3) UNIT temperature (Tx) C F metric (M) (024) (076) non-metric (N) (002) (083) (003) (085) (004) (015) Digital output setup PROTOCOL BAUDRATE PARITY STOPBITS UNIT Modbus RTU 4) (1) 9600 (A) odd (O) 1 stopbit (1) metric (M) BACnet MS/TP 5) (3) (B) even (E) 2 stopbit (2) non-metric (N) (C) no parity (N) ) (D) ) (E) ) (F) 1) A combination of analog and digital version is not possible 2) Analogue version only 3) Other scaling upon request 4) Modbus Map and setup instructions: See User Guide and Modbus Application Note at 5) Product Implementation conformance Statement (PICS) availbale at 6) Only for BACnet Order example Analog output EE160-HT6xAPAB-Tx003M Model: humidity + temperature transmitter Analog output: 4-20mA Passive T-Sensor: Pt 100 DIN A Housing: polycarbonate Type: wall mounting Filter: membrane filter Output scaling: temperature Scaling: Unit: metric Digital output EE160-HTx3xPBB-1AE1N Model: humidity + temperature transmitter Digital output: RS485 Housing: polycarbonat Type: duct mounting Filter: membrane filter Protocol: Modbus Baudrate: 9600 Parity: even Stopbits: 1 Unit: non-metric 12 v2.0 / Modification rights reserved EE160

14 T: (+34) Accessories Product configuration adapter Product configuration software Power supply adapter see data sheet EE-PCA EE-PCS (free download: V03 (see data sheet Accessories) Scope of supply Model EE160 Wall mount (Type A) EE160 Duct mount (Type B) Additionally for all EE160 with RS485 interface EE160 Transmitter according ordering guide Cable gland Mounting kit Mounting flange Inspection certificate according to DIN EN Quick Guide - EE160 RS485 Setup EE160 v2.0 / / Modification rights reserved 13

15 EE10 EE10 room transmitters are the ideal solution for indoor applications such as HVAC in residential and official buildings. The very stylish, functional housing makes easy installation and fast exchange of the sensing unit for service purposes possible. The high quality E+E humidity sensor and state-of-the-art microprocessor controlled electronics are the guarantee for best accuracy and a wide range of options. The standard humidity output of EE10 transmitters is 4-20 ma or 0-10 V. The temperature output signal can be active or passive. All EE10 versions can be equipped with a good legible LC display. For EE10-FT versions the displayed values for humidity and temperature will alternate. Two different housing designs ensure professional appearance according to regional standards. Typical Applications building management for residential and office areas air conditioning in switching cabinets climate control in hotels and museums Technical Data Measuring Quantities Relative Humidity Humidity sensor HC103 Analogue output % RH 0-10 V -1 ma < I L < 1mA 4-20 ma (two wires) R L < (U V -10)/0.02 < 500 Ohm Working range 1) % RH Accuracy at 20 C (68 F) and U V =24VDC ±2% RH ( % RH) ±3% RH ( % RH) Traceable to intern. standards, administrated by NIST, PTB, BEV... Temperature dependence at 60% RH typical 0.06% RH / C (0.03% RH / F) Temperature (active output) 0-10 V -1 ma < I L < 1mA 4-20 ma (two wires) R L < (U V -10)/0.02 < 500 Ohm Accuracy at 20 C (68 F) and U V =24VDC FT3: ±0.25 C (±0.45 F) FT6: ±0.4 C (±0.72 F) Temperature (passive output) Type of T-Sensor please see ordering guide General Data Voltage supply (U V ) for 0-10 V VDC or 24 VAC ±20% for 4-20 ma 28V DC > U V > x R L (R L < 500 Ohm) Current consumption for DC supply: typical 4 ma for AC supply: typical 15 ma eff Electrical connection screw terminals max. 1.5 mm 2 (AWG 16) Housing material Polycarbonat US Version: UL94V-0 approved / EU Version: UL94HB approved Protection class IP30 Display for EE10-FTx version Humidity / Temperature alternating for EE10-Fx and EE10-FPx version Humidity CE compatibility according EN EN Temperature ranges working temperature range: C ( F) storage temperature range: C ( F) 1) Please refer to the working range of the HC103 (+34) HVAC Humidity / Temperature Transmitter for Indoor Applications EE10 Features excellent price / performance ratio easiest installation modern design long term stable optional display 50 v2.9 / Modification rights reserved EE10

16 (+34) Connection Diagram EE10-FT3 EE10-FP3 EE10-FT6 EE10-FP6 Dimensions (mm) Housing colour: Standard (EU & US): Front cover: Signal white RAL 9003 Back cover: Light grey RAL 7035 Optional (only EU): Front and Grey (Anthracite grey RAL 7016) back cover Silver (White aluminum RAL 9006) EU: W x H x D = 85 x 100 x 26 mm (3.3 x 3.9 x 1") US: W x H x D = 85 x 136 x 26 mm (3.3 x 5.4 x 1") Ordering Guide MODEL OUTPUT T-SENSOR 1) (only passive) DISPLAY HOUSING DESIGN & COLOUR T-UNIT T-SCALE 2) (only for FT) humidity + (FT) 0-10 V (3) Pt 100 DIN A (A) without display (--) EU-Standard (RAL9003 / RAL7035) (--) C (--) (T04) temperature 4-20 ma (6) Pt 1000 DIN A (C) with display (D04) EU-Grey (RAL7016) (G) F (E01) (T31) humidity + (FP) Ni1000, TK6180 (J) EU-Silver (RAL9006) (S) (T55) temperature passive NTC10k (E) US (RAL9003 / RAL7035) (US) (T15) NTC1.8 (G) (T76) (T96) EE10-1) T-Sensor details see 2) other scaling upon request Order Example EE10-FT3-D04-T04 Model: humidity + temperature Output: 0-10 V Display: with display Housing design & colour EU-Standard (RAL9003 / RAL7035) T-Unit: C T-Scale: Scope of supply - EE10 Transmitter according to ordering guide - Mounting materials - Test report according to DIN EN EE10 v2.9 / Modification rights reserved 51

17 EE02 The new hygrometer EE02 is the combination of high accuracy measurement technology with modern design. The relative humidity and temperature values with trend indication are alternating on the large display. High quality E+E sensor technology and state of the art microprocessor based electronics result in highest accuracy and long term stability. The very low power consumption allows battery operation and independence from external power supply. The standard batteries, replaceable by the user, have a life time about 5 years. The modern housing concept makes the wall mounting very easy. EE02 can be used as bench mount as well, the free standing kit is included in the scope of supply. EE02 is available upon request as OEM thermo - hygrometer with your company logo. Typical Applications climate monitoring for: - office spaces - private areas - laboratories - food stores gift article Technical Data T: (+34) Measuring Quantities Relative Humidity Humidity sensor type HC103 Working range 1) % RH Resolution 0.1% RH Accuracy at 20 C (68 F) ±2% RH ( % RH) ±3% RH ( % RH) Traceable to intern. standards, administrated by NIST, PTB, BEV... Trend indication yes Temperature active Working range C ( F) Resolution 0.1 C Accuracy at 20 C (68 F) ±0.3 C (±0.54 F) Trend indication yes General Data Sampling rate 10s Current supply 2x 1.5V AAA Alkali battery (not in the scope of supply) Battery life time typ. 5 years Display C or F (selectable by jumper) CE compatibility according EN EN Temperature ranges Working temperature range: C ( F) Storage temperature range: C ( F) Dimensions 85 x 100 x 26 mm (3.3 x 3.9 x 1 ) Housing / protection class PC, IP20 1) Please refer to the working range of the HC103 Ordering Guide MODEL High-Precision Thermo - Hygrometer EE02 Features easiest mounting modern design highest accuracy traceable calibration long battery life time available as OEM meter EE02 with E+E logo EE02 without E+E logo (EE02-FT01) (EE02-FT01-L01) 74 v2.4 EE02

18 EE08 High-Precision Miniature Humidity / Temperature Transmitter Accurate humidity / temperature measurement over a wide working range, fitted in a small-sized housing and high flexibility have been the main goals for the development of the EE08 series. Low power consumption and short start-up time support efficient energy management for battery operated systems. with cable For this application an additional version (V10) with supply voltage V DC has been developed. Calibration data and other relevant functions like linearization or temperature compensation are stored in the probe. This feature, together with the optional connector, allows for with connector easy replacement of the probe without a need for re-adjustment of the reading device (interchangeability). The humidity and temperature measurement are available as analogue outputs (0-1/2.5/5 V) and as a digital interface (E2-interface). Easy implementation and data processing is warranted. Humidity and temperature reading can be re-adjusted using the calibration software; available as an accessory. The configuration equipment allows humidity and temperature adjustment of the sensor. Typical Applications meteorology / weather stations humidity / temperature data logging incubators fermentation chambers green houses snow machines dry storage facilities Features small dimensions wide working range, high accuracy traceable calibration customer adjustment possible interchangeable in seconds low power consumption / short start-up time analogue outputs / digital interface Technical Data Measuring values Relative Humidity Sensor HC101 Working range 1) % RH Digital output (2 wire) 2) output value: % RH Analogue output % RH 0-1/2.5/5/10 V -0.2 ma < I L < 0.2 ma Accuracy at 20 C (68 F) and 12 V DC *) ±2 % RH ( % RH) ±3 % RH ( % RH) Temperature dependence typ % RH/ C (typ % RH/ F) Temperature Sensor Pt 1000 (DIN A) Digital output (2 wire) 2) output value: C ( F) Analogue output 0-1/2.5/5/10 V -0.2mA < I L < 0.2 ma Accuracy at 12/24V DC C (+34) C General Supply voltage output 0-1 V / V V DC or 7-30 V DC output 0-5 V 7-30 V DC output 0-10 V V DC Current consumption typ. < 1.3 ma Digital interface E2-interface level = 3.3 V / ±0.1 V Housing polycarbonate / IP65 Sensor protection metal grid filter Electromagnetic compatibility EN EN Industrial Environment Temperature ranges working temperature: C ( F) storage temperature: C ( F) 1) refer to the working range of the humidtiy sensor HC101 2) serial protocol refer to *) The accuracy statement includes the uncertainty of the factory calibration with an enhancement factor k=2 (2-times standard deviation). The accuracy was calculated in accordance with EA-4/02 and with regard to GUM (Guide to the Expression of Uncertainty in Measurement). 68 v2.0 / Modification rights reserved EE08

19 (+34) Dimensions (mm) EE08 with cable (Type E) 61 (2.4 ) M12x1 EE08 with connector (Type D) 83 (3.3 ) M16x (0.5 ) 25 (1 ) 73 (2.9 ) 12 (0.5 ) 61 (2.4 ) 71 (2.8 ) connector M12 (8-pole) Connection Diagram Type E: Temp. active T-passive white (not connected) white, black T-passive blue (not connected) blue, violet GND pink pink T-out grey grey (not connected) RH-out yellow yellow SCL} green green SDA brown brown +UB red red Temp. passive, 4-wire Type D: 1 T-passive 2 SDA 3 SCL } E2-interface 4 RH-out 5 T-out 6 GND 7 T-passive 8 +UB Ordering Guide HOUSING MODEL OUTPUT SUPPLY T-SENSOR 3) (passive, 4-wire) polycarbonate (P) humidity active / temperature active (FT) 0-1 V 1) (1) V DC (V10) Pt 100 DIN A (A) with connector (D) humidity active / temperature passive (FP) V 1) (7) 7-30 V DC (V11) Pt 1000 DIN A (C) with cable (E) 0-5 V 2) (2) 0-10 V 2) (3) TYPE EE08- FILTER COATING CABLE LENGTH (Type E only) T-UNIT T-SCALING metal grid filter (6) without coating (no code) 1 m (3.3ft) (01) metric (no code) (T22) with coating (HC01) 2 m (6.6ft) (02) non metric (E01) (T02) 5 m (16.4ft) (05) (T08) (T24) (T48) other (Txx) 1) possible with supply V DC (V10) or 7-30 V DC (V11) 2) possible with supply 7-30 V DC (V11) only 3) T-Sensor details see Order Example EE08-PFT2V11E602T22 housing: polycarbonate model: humidity active / temp. active output: 0-5V supply: 7-30V DC type: with cable Scope of Supply - EE08 Transmitter according to ordering guide - Inspection certifi cate according to DIN EN filter: coating: cable length: T-unit: T-scaling: metal grid filter without 2m (6.6ft) metric C Accessories / Replacement Parts - M12 connection cable for type D, length 1.5 m (5 ft) (HA010322) - M12 connection cable for type D, length 3 m (10 ft) (HA010323) - M12 connection cable for type D, length 5 m (16.4 ft) (HA010324) - M12 connection cable for type D, length 10 m (32.8 ft) (HA010325) - Radiation shield for Type E (HA010502) - Radiation shield for Type D (HA010506) - Protection cap for 12 mm probe (HA010783) - M12 female socket with wires (HA010703) - M12 female cable connector assembly possible (HA010704) - metal grid filter (HA010113) Configuration equipment: The configuration equipment allows humidity and temperature adjustment of the sensor. - configuration cable (HA011005) - configuration software: free download under EE08 v2.0 / Modification rights reserved PC HA

20 EE060 T: (+34) OEM Humidity and Temperature Probe with Voltage Output EE060 is the ideal solution for cost-effective, highly accurate and reliable measurement of relative humidity (RH) and temperature (T). Excellent protection against external infl uences is ensured by the combination of completely encapsulated electronics and the long-term stable, very robust HCT01 humidity sensor with E+E proprietary protective coating. Together with the optional radiation shield, the probe can be also used outdoors. sensor coating EE060 is available as cable or plug version, with wide temperature and supply voltage ranges and 0-1V, 0-5V or 0-10V analog outputs. The 0-1V version features also an optional T sensor with passive output. sealed solder pads encapsulated electronics EE060 Typical Applications incubators and hatchers greenhouses and livestock barns humidifiers and dehumidifiers storage rooms HVAC Features optimal price-performance ratio electronics encapsulated against water RH sensor coated against dust and dirt very robust sensing head excellent long term stability Technical Data Measuring values Relative humidity Sensor HCT01-00D Working range % RH Analogue output % RH 0-10V -1.0 ma < I L < 1.0 ma 0-5V -0.2 ma < I L < 0.2 ma 0-1V -0.1 ma < I L < 0.1 ma Accuracy at 24V DC, 20 C (68 F) ±2.5% RH Temperature active Sensor Pt1000 DIN B Analogue output C ( F) 0-10V -1.0 ma < I L < 1.0 ma 0-5V -0.5 ma < I L < 0.5 ma 0-1V -0.1 ma < I L < 0.1 ma Accuracy at 24V DC, 20 C (68 F) ±0.3 C (±0.5 F) Temperature passive (with 0-1V output and 8-pole connector only) Output resistive, 2-wire Type of T-Sensor refer to ordering guide General Supply voltage HT1: V DC HT2: V DC HT3: V DC Current consumption typ. 1.5 ma Electrical connection M12 connector or cable (PVC, Ø 4.3mm, 4 x 25mm²) Housing polycarbonate / IP65 Electromagnetic compatibility 1) EN (industrial environment) EN Working and storage temperature C ( F) 1) Analogue output 0-1V is not protected against surge! 26 v1.4 / Modification rights reserved EE060

21 T: (+34) Dimensions in mm (inch) Connector version Cable version 11 (0.43) 99.5 (3.92) 106 (4.17) 34 (1.34) Ø12 (0.47) (4) 34 (1.34) M12x1 Ø12 (0.47) Connection Diagram Connector version Connector 4-pole (PM) 1...V+ 2...RH-out 3...GND 4...T-out Connector 8-pole (PV) 1...T-passive 2...not connected 3...not connected 4...RH-out 5...T-out 6...GND 7...T-passive 8...V Supply voltage HT1: V DC HT2: V DC HT3: V DC cable version (Type PN) Supply voltage HT1: V DC HT2: V DC HT3: V DC + - V V+ (white) GND (brown) V RH (green) T (yellow) Ordering Guide ANALOG OUTPUT T-SENSOR PASSIVE (with 0-1V output and 8-pole connector only) ELECTRICAL CONNECTION CABLE LENGTH FILTER 0-1V (1) none (x) connector 4-pole (PM) 0.5m (1.6ft) (A) membrane filter (B) 0-5V (2) Pt1000 DIN A (C) connector 8-pole (fort-sensor passive) (PV) 1.5m (4.9ft) (C) 0-10V (3) NTC 10k at 25 C (E) cable (PN) 3m (9.8ft) (E) with connector (x) EE060-HT Order Example EE060-HT2xPMxB Output: 0-5V T-Sensor passive: none El. Connection: connector 4-pole Cable length: with connector Filter: membrane filter EE060-HT1CPVxB Output: 0-1V T-Sensor passive: Pt1000 DIN A El. Connection: connector 8-pole Cable length: with connector Filter: membrane filter Accessories (For further information, see data sheet Accessories ) Female connector 4pol. self assembly M12x1 Female connector 8pol. self assembly M12x1 Connection cable for Type PM, free ends 1,5m (4.9ft) / 5m (16.4ft) / 10m (32.8ft) Connection cable for Type PV, free ends 1,5m (4,9ft) / 3m (9.8ft) / 5m (16.4ft) / 10m (32.8ft) Protection cap for M12 female cable connector Protection cap for M12 male probe connector Protection cap for 12 mm sensing head Plastic mounting flange for duct mounting Radiation shield HA HA HA010819/20/21 HA010322/23/24/25 HA HA HA HA HA Support literature EE060 v1.4 / Modification rights reserved 27

22 EE46 T: (+34) Condensation Monitor EE46 condensation monitors are used to monitor the formation of condensation on chilled ceilings or to prevent condensation at critical spots of heating-, ventilation- and air conditioning systems. It is also used as a dew point monitor for systems operating near the dewpoint. Because of the temperature coupling between the condensation monitor and the environment, the relative humidity is a measure for the dew point. The condensation monitor measures the relative humidity near the dew point using its high-quality capacitive sensor. At reaching the switching point of 90% RH the output will provide an early warning signal for the initiation of control steps (increasing the initial water EE46 temperature, reducing the cooling capacity, switching on the heating, etc...). An additional status light indicates the condensation danger. Thanks to the special protection coating, sensor and electronics are highly insensitive to dust and dirt. EE46 condensation monitors can be mounted on walls, ducts and pipes up to 2. Typical Applications chilled ceilings heating-, ventilation- and air conditioning systems switching cabinets Technical Data Humidity sensor Working range Switching point at 20 C (68 F) Switching hysteresis HC % RH 90±3% RH Hysteresis 5% RH Features early detection of condensation danger compact design fast response time dust protection simple and easy mounting status indication 85±3% RH 90±3% RH Response time at change of pipe/wall temperature t 90 < 3 min. Response time at change of t 90 < 25 sec. relative humidity Electrical output potentialfree relay with changeover contact Switching capacity max. 24V AC/DC, 1A Supply voltage 24V AC/DC ±20% Current consumption at 24V DC < 3mA Relay status indication LED, red Electrical connection 5-pole push-in terminal, max. 1.5 mm 2 (AWG 16) Dust protection by special coating (permeable for water vapour) Housing protection class IP40 Housing material Polycarbonate, UL94-V2 approved Electromagnetic compatibility EN EN industrial environment Temperature range working temperature range C ( F) storage temperature range C ( F) Weight approx. 60g 48 v1.2 / Modification rights reserved EE46

23 T: (+34) Dimensions (mm) 1 mm = / 1 = 25.4 mm Installation Pipe mounting max. Ø 50mm (2 ) max. Ø 50mm (2 ) Wall mounting Ø Connection Diagram Status Indication V+ GND power supply 24V AC/DC ±20% NC COM NO LED continuous red: Operating < 90% RH LED blinking red: Condensation danger Ordering Guide Condensation Monitor EE46 (EE46) EE46 v1.2 / Modification rights reserved 49