200W Slim Type with PFC Switching Power Supply

Transcription

1 Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID W Slim Type with PFC Switching Power Supply GB494 UL EN IEC EN605- % - ~+ Industrial automation machinery Industrial control system Mechanical and electrical equipment Electronic instruments, equipments or apparatus Household appliances LED display application is a 00W single-output slim type power supply with 6mm of low profile design. Adopting the full range 90~64VAC input, the entire series provides an output voltage line of.v, 4.V, 5V, V, 5V, 4V, 6V and 48V. In addition to the high efficiency up to 94%, that the whole series operates from -0 ~ 70 under air convection without fan. UHP-00 has the complete protection functions and 5G anti-vibration capability;it is complied with the international safety regulations such as TUV EN60950-, EN605-, UL and GB494. serves as a high performance power supply solution for various industrial applications. R File Name:UHP-00-SPEC

2 SPECIFICATION MODEL 00W Slim Type with PFC Switching Power Supply UHP UHP UHP-00-5 UHP-00 - UHP-00-5 UHP-00-4 UHP-00-6 UHP OUTPUT INPUT PROTECTION FUNCTION OTHERS NOTE VOLTAGE ADJ. RANGE.~.5V.6~4.4V 4.5~5.5V.4~.6V VOLTAGE TOLERANCE Note. ±.0% ±.0% ±.0% ±.0% LINE REGULATION ±0.% LOAD REGULATION ±.0% ±.0% ±.0% SETUP, RISE TIME 000ms, 80ms/0VAC 000ms, 80ms/5VAC at full load HOLD UP TIME (Typ.) 0ms/0VAC 0ms/5VAC VOLTAGE RANGE Note.4 90 ~ 64VAC 7 ~ 70VDC FREQUENCY RANGE 47 ~ 6Hz POWER FACTOR (Typ.) PF 0.94/0VAC PF 0.98/5VAC at full load EFFICIENCY (Typ.) 89% 90% 9% 9% AC CURRENT (Typ.).A/5VAC.A/0VAC INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVERLOAD OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY & EMC (Note.6) DC VOLTAGE RATED CURRENT.V 40A RATED POWER(convection) W RIPPLE & NOISE (max.) Note. 50mVp-p DC OK SIGNAL(Optional) REDUNDANT(Optional) SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF DIMENSION Cold start 40A/5VAC <0.75mA / 40VAC 4.V 40A 68W 50mVp-p 0~40% rated output power 80A/0VAC Protection type : Hiccup mode, recovers automatically after fault condition is removed.8~ 4.6V Protection type :Shut down O/P voltage,re-power on to recover Protection type :Shut down O/P voltage, recovers automatically after temperature goes down Contact rating(max.):5vdc/0ma resistive load -0 ~ +70 (Refer to Derating Curve") 0 ~ 90% RH non-condensing -40 ~ +85, 0 ~ 95% RH non-condensing ± 0.0%/ (0 ~ 50 ) 0 ~ 500Hz, 5G 0min./cycle, 60min. each along X, Y, Z axes 57K hrs min. MIL-HDBK-7F (5 ) 94*55*6mm (L*W*H) 5V 40A 00W 00mVp-p V 6.7A 00.4W 40mVp-p 40mVp-p 4.~5.8V PACKING 0.468kg;4pcs/.kg/0.49CUFT 5V.4A 0W ±.0% ±0.% 4V 8.4A 0.6W 40mVp-p.8~5.V ±.0% ±0.% 6V 5.6A 0.6W 40mVp-p 4.~7.8V ±.0% ±0.% For parallel connection protection:for parallel applications, when one PSU can not work, the another one will be automatically enabled. This can prevent the system crash, and provide the reliability of system UL60950-,TUV EN60950-,EN605-, CCC GB494 approved I/P-O/P:.75KVAC I/P-FG:KVAC O/P-FG:.5KVAC I/P-O/P, I/P-FG,O/P-FG:00M Ohms/500VDC/5 / 70%RH Compliance to EN550,GB954,Class B, EN5504,EN6000--,- 94% 94% Compliance to EN ,,4,5,6,8,;EN (EN5008-), heavy industry level,criterial A 48V 4.A 0.6W 00mVp-p 45.6~50.4V ±.0% ±0.% 4.6 ~ 5.46V 5.75 ~ 6.75V. ~ 5.6V 6.5 ~ 9.5V 6.4 ~.V 9.6 ~46.8V 5.8 ~ 6.4V 94% 94% File Name:UHP-00-SPEC

3 00W Slim Type with PFC Switching Power Supply Block Diagram I/P EMI FILTER & RECTIFIER PFC CIRCUIT POWER SWITCH- ING RECTIFIERS & FILTER FG O.T.P. O.L.P. CONTROL DETECTION CIRCUIT O.V.P. DC OK Function Redundant Function Derating Curve LOAD (%) (HORIZONTAL) AMBIENT TEMPERATURE ( ) STATIC CHARACTERISTIC LOAD (%) INPUT VOLTAGE (V) 60Hz File Name:UHP-00-SPEC

4 00W Slim Type with PFC Switching Power Supply Function Manual.DC_OK Signal DC_OK is a collector shorted signal. It is used by an optocoupler in the power supply which indicates the output status of the power supply as exhibited below. DC OK K Optocoupler C-E Pin Conduction PSU turns on DC ok C E Optocoupler C-E Pin Open Optocoupler Rating(max.) PSU turns off DC fail 5Vdc/0mA resistive load GND PSU COM.Redundant function () UHP-00R is built-in redundant function and can be connected units in parallel. () When in parallel operation the maximum load should not be greater than the rated power of any PSU. PSU LOAD PSU File Name:UHP-00-SPEC

5 00W Slim Type with PFC Switching Power Supply Mechanical Specification CASE NO.:49B Unit:mm VR R.65 6 AC Input Terminal(TB) pin NO. Assignment Terminal Max mounting torque Pin No. Assignment AC/L AC/N (DEGSON) DG8C-B-0P 5Kgf-cm DC Output Terminal(TB,TB) pin NO. Assignment Pin No. Assignment Terminal Max mounting torque, (MW),4 TB-HTP-00-40A 8Kgf-cm DC OK Connector(CN0):JST BB-PH-K-S or requivalent Mating Housing Terminal Pin No. Assignment DC COM DC OK JST PHR- or requivalent JST SPH-00T-P0.5S or requivalent File Name:UHP-00-SPEC

6 00W Slim Type with PFC Switching Power Supply Installation.Operate with additional aluminum plate In order to meet the Derating Curve and the Static Characteristics, must be installed onto an aluminum plate(or the cabinet of the same size) on the bottom.the size of the suggested aluminum plate is shown as below. And for optimizing thermal performance, the aluminum plate must have an even and smooth surface (or coated with thermal grease), and must be firmly mounted at the center of the aluminum plate. unit:mm 00 M*4 00 5cm 4 VR.For heat dissipation, at least 5cm installation distance around the PSU should be kept, shown as below: 5cm File Name:UHP-00-SPEC