DMS / DLS / VNS Recorders

Transcription

1 Commissioning English Dallmeier DMS / DLS / VNS Recorders / Rev...0

2 Contents Contents Validity...2 Safety instructions...3 Requirements...4 HDD mounting...5 Mounting DMS... 6 Mounting DLS / VNS...7 DMS 0 / 60 / 240 / 240 HSR / 240 IPS... DMS 0 Bank / 60 Bank / 240 Bank...0 DLS 4 / / Plus / 6 / 6 Plus... 2 DLS 4 Bank... 4 VNS Commissioning and login DMS / DLS... Commissioning and login VNS...9 Validity This documentation applies to all recorders of the DMS, DLS and VNS series listed below. It has been produced on basis of software version DMS 0 DLS 4 DLS 4 Bank VNS 6 DMS 60 DLS DMS 0 Bank DMS 240 DLS Plus DMS 60 Bank DMS 240 HSR DLS 6 DMS 240 Bank DMS 240 IPS DLS 6 Plus DMS 240 HSR Bank Observe the corresponding documentations Main Functions, Operation and Configuration in addition. 2

3 Safety instructions Only use this unit if it is technically in proper working order, to the intended purpose and while keeping safety and potential dangers in mind. Qualified personnel Installation, mounting, connection, commissioning and configuration of the unit may only be carried out by qualified personnel. This also applies to the maintenance, testing and repair, whereat the regulations of the DIN VDE 070 series of standards (repair, modification and inspection of electrical appliances) must be followed. Regulations The use of video and audio surveillance systems in general is strictly regulated. Inform yourself about the applicable laws and regulations regarding data, working and environmental protection before using the unit and ensure compliance with them. System components Only use internal components that have been tested and approved by Dallmeier. Inappropriate internal components can cause malfunctions, damages and data loss and can result in loss of warranty. RAID System Devices that are configured with a RAID system for redundant recording always must be supplied with power via an uninterruptable power supply (UPS). A sudden voltage drop can damage the RAID system. Modifications Do not make any modifications to the hardware or software that has not been tested and approved by Dallmeier. Inappropriate modifications can cause malfunctions, damages and data loss and can result in loss of warranty. Documentation Carefully and completely read the documents included in delivery. Always observe the contained instructions, notes and warnings. Condensation water If the unit is brought from a cold to a warm environment, resulting condensation water can cause malfunctions and damages. In this case wait (up to hours) until the unit has reached room temperature before commissioning. Operating conditions Unfavourable operating conditions can shorten the life of the unit and can cause malfunctions, damages and data loss and can result in loss of warranty. Observe the specifications given in the technical data, the operating condition requirements and the maintenance instructions. Shocks Shocks can cause malfunctions and damages. The unit may not be moved while in operation. Foreign objects If objects or liquids get into the unit, immediately disconnect it from the power supply (pull out the power plug). Contact the sales partner responsible for your area. Burnt smell If you notice burnt smell or formation of smoke from the unit, immediately disconnect it from the power supply (pull out the power plug). Contact the sales partner responsible for your area. Opening The housing of the unit may only be opened by qualified personnel for inspection, maintenance and repair. Disposal Disconnect the unit from the power supply. Remove all connected devices. Return the unit to your respective sales partner. Safety Requirements HDD mounting Mounting DLS DMS DMS Bank DLS DLS Bank VNS Login DMS Mounting DMS Login VNS 3

4 Requirements Ambient conditions The DMS / DLS / VNS is designed for stand-alone operation. As an option it can be mounted and commissioned in a 9" standard rack. General Unfavourable ambient conditions can shorten the life and cause malfunctions or damages. Do not operate the recorder at places with: large scale dust and dirt steam or oil vapours (e.g., kitchen) unsuitable ambient temperatures insufficient ventilation (e.g., closed cabinet) direct sunlight sources of strong heat dissipation (e.g., radiator) sources of strong radiation (e.g., radio transmitter, magnetic field) corrosive surrounding (e.g., gas, salt water) Stand-alone operation The recorder normally can be set up and operated at any place that meets the requirements above. Observe the following requirements and notes in addition. Computer room This recorder is not for use in a computer room as defined in the US fire protection regulation Standard for Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. Secured room Risk of manipulation and sabotage. A stand-alone installation should be made in secured rooms with restricted access only. Socket-outlet The socket-outlet to be used has to be installed near the device. Is has to be easily accessible. Operation in a 9" rack The recorder can be installed and operated in a 9" standard rack, that is situated at a place that meets the requirements above. Observe the following requirements and notes in addition. Elevated ambient temperature The ambient temperature in a multi-unit rack may be higher than the room ambient. Ensure that the maximum ambient temperature in the rack complies with the requirements specified in the technical data. Reduced air flow The air flow in a (closed) rack may be reduced. Ensure that the amount of air flow required for save operation is not compromised. Ensure sufficient ventilation with 0 cm free space on the recorder s front, rear and right side. Earthing Always ensure reliable earthing of the recorder. 4

5 HDD mounting Recorders that have been ordered with hard disk drive can directly be mounted, connected and commissioned. Recorders that have been ordered without hard disk drive must be equipped with one 3.5" hard disk drive at least. Note that all mounted hard disk drives must be tested and released for mounting by Dallmeier (HDD whitelist in the Partner Forum)! may not be formatted or partitioned! Also note that the following HDD slots must be used in case that only one hard disk drive is mounted: Recorder Position Slot for HDD DMS Front side Top DLS Rear side Left VNS Rear side Left Ensure that the recorder is switched off and disconnected from the power supply. Unlock the HDD drawer unit with the key. Pull the HDD drawer unit carefully out of the housing. Remove the cover panel mounted on the HDD drawer unit. Place the HDD drawer unit on the HDD s underside. Ensure that the connections of the HDD are positioned at the rear side of the HDD drawer unit. Ensure that HDD and HDD drawer unit flush at the rear side. Mount the HDD drawer unit with 4 screws on the HDD. Insert the HDD drawer unit into the guide rail. Slide the HDD drawer unit carefully and completely into the housing. Ensure that you slide it straight. Do not use any force. Ensure that HDD drawer unit and housing is flush. Lock the HDD drawer unit with the key. The HDD will be initialised and set into operation during the first start of the recorder. IMPORTANT ADVICE Depending on the number and the properties (capacity, new or used) of the mounted hard disk drives, various messages and dialogues are displayed during the first start and the initialization. Confirm the messages, if required. Observe the instructions given in the dialogues. Safety Requirements HDD mounting Mounting DMS Mounting DLS DMS DMS Bank DLS DLS Bank VNS Login DMS Login VNS Note the appropriate Configuration documentation. Load the Default System Parameters as first step of the configuration. 5

6 Mounting DMS Stand-alone operation Ensure a stable and horizontal surface. Ensure 0 cm of free space at the front, rear and right side. Connect the recorder as described on the following pages. Commission the recorder as described on the following pages. Operation in 9" rack Exclusively use the 9 holder provided by Dallmeier. Insert the recorder into the 9" holder. Use the housing feet as guidance. Use the 4 screws delivered with the 9" holder. Mount the housing in the 9" holder with the 4 screws. Ensure that the ventilation slots are not covered. Mount the recorder into the 9" rack. Observe the instructions of the rack manufacturer. Ensure 0 cm of free space at the front, rear and right side. Connect the recorder as described on the following pages. Commission the recorder as described on the following pages. 6

7 Mounting DLS / VNS Stand-alone operation Ensure a stable and horizontal surface. Ensure 0 cm of free space at the front, rear and right side. Connect the recorder as described on the following pages. Commission the recorder as described on the following pages. Operation in 9" rack Exclusively use the 9" holders provided by Dallmeier. Remove the 4 housing screws at the sides. Use the 4 screws delivered with the 9" holders. Mount the 9" holders with the 4 screws to the housing. Ensure that the ventilation slots are not covered. Mount the recorder into the 9" rack. Observe the instructions of the rack manufacturer. Ensure 0 cm of free space at the front, rear and right side. Connect the recorder as described on the following pages. Commission the recorder as described on the following pages. Safety Requirements HDD mounting Mounting DMS Mounting DLS DMS DMS Bank DLS DLS Bank VNS Login DMS Login VNS 7

8 DMS 0 / 60 / 240 / 240 HSR / 240 IPS Connections The number of the connections can differ depending on the ordered equipment or device variant. The following description refers to a device with full equipment and optional connectors. A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A Contact IN cameras (-6/7-2/3-/9-24) N Ethernet interface 4x Weidmüller, pins RJ45, 0/00/000 Mbps B Contact IN global (-6) O Microphone IN Weidmüller, pins 3.5 mm phone socket, red, 4.3 kohm, 2.2 Vpp (for intercom) C Relay OUT (-5) P Audio OUT Weidmüller, 0 pins 3.5 mm phone socket, green, kohm, 2.2 Vpp (for live, playback, intercom) D Serial interface Q AUX / Line IN Weidmüller, 2 pins, RS45 (for Dallmeier PTZ domes only) 3.5 mm phone socket, blue, 6 kohm, 2.2 Vpp (for intercom) E Mouse R Serial interface PS/2, green D-SUB, 9 pins, RS232 F Keyboard S Video OUT DVI PS/2, purple Dual-Link (24 + 5), DVI-I, 024 x 76 (video and configuration) G Video IN (-24) T Video OUT (3-4) BNC, 75 Ohm, Vpp, with loop-through, CVBS BNC, 75 Ohm, Vpp, CVBS (same signal as Video OUT and 2 (K)) H Serial interface COM U Not active D-SUB, 9 pins, RS232 2x 3.5 mm phone socket I Parallel interface LTP V SATA interface D-SUB, 25-pole, IEEE 24 Serial ATA 3.0 Gbips (SATA II), Multilane (only for Dallmeier DAS-4 Eco) J Video OUT VGA W Audio IN (-/9-6/7-24) Mini-D-SUB, 5-pole, VGA, 024 x 76 (video and configuration) D-SUB, 5-pole, kohm, 2.2 Vpp (for D-SUB/Cinch adapter cable) K Not active X 2V DC OUT 2x RJ45 ODU socket, 2-pole, 2V DC L Video OUT (-2) Y Mains connection BNC, 75 Ohm, Vpp, CVBS (only video, no configuration) IEC C4 socket, 0 / 230 V AC + / 0 %, 50 / 60 Hz M USB interface Z Mains switch 2x USB 2.0, type A Technical data Dimensions W x H x D Voltage supply Power consumption Heat power Ambient temperature Humidity Atmospheric load Weight Approx. 425 x 22 x 446 mm (without feet) / 425 x 30 x 446 mm (with feet) 0 / 230 V AC + / 0 %, 50 / 60 Hz Max. 30 W Max. 444 BTU/h 5 40 C, C recommended 5 70 % RH, not condensing Dust-free Approx. 0 2 kg

9 DMS 0 / 60 / 240 / 240 HSR / 240 IPS Assignment of the sockets Contact IN cameras (A) Weidmüller, pins GND 2 Contact 3 Contact 2 Contact IN global (B) Weidmüller, pins GND 2 Contact 3 Contact 2 Relay OUT (C) Weidmüller, 0 pins 4 Contact 3 5 Contact 4 6 Contact 5 Triggering event Type + 2 Relay Recorder in alarm state Normally open Relay 2 None Normally open Relay 3 System error Normally closed 7 + Relay 4 None Normally open Relay 5 More than 0 % of the secure tracks occupied Normally open Serial interface (G and Q) D-SUB, 9 pins DCD (Data Carrier Detect) 2 RxD (Receive Data) 3 TxD (Transmit Data) Audio IN (W) D-SUB, 5-pole, without D-SUB/Cinch adapter cable Audio 2 Audio 2 3 Audio 3 4 Audio 4 5 Audio 5 2V DC OUT (X) ODU socket, 2-pole 2V DC 2 GND 4 Contact 3 5 Contact 4 6 Contact 5 4 DTR (Data Terminal Ready) 5 GND 6 DSR (Data Set Ready) 6 Audio 6 7 Audio 7 Audio 9 GND 0 GND 2 7 Contact 6 GND 7 Contact 6 GND GND 3 2 GND 4 3 GND 5 4 GND 6 5 GND RTS (Request to Send) CTS (Clear to Send) 9 RI (Ring Indicator) 6 2 Serial interface (D) Weidmüller, 2 pins RX+ 2 RX Safety Requirements HDD mounting Mounting DMS Mounting DLS DMS DMS Bank DLS DLS Bank VNS Login DMS Login VNS 9

10 DMS 0 Bank / 60 Bank / 240 Bank / 240 HSR Bank Connections The number of the connections can differ depending on the ordered equipment or device variant. The following description refers to a device with full equipment and optional connectors. A B C D E F G H I J K L M N O P Q R S T U V W X Y A Contact IN cameras (-6/7-2/3-/9-24) N Ethernet interface 4x Weidmüller, pins RJ45, 0/00/000 Mbps B Contact IN global (-6) O Microphone IN Weidmüller, pins 3.5 mm phone socket, red, 4.3 kohm, 2.2 Vpp (for intercom) C Relay OUT (-5) P Audio OUT Weidmüller, 0 pins 3.5 mm phone socket, green, kohm, 2.2 Vpp (for live, playback, intercom) D Serial interface Q AUX / Line IN Weidmüller, 2 pins, RS45 (for Dallmeier PTZ domes only) 3.5 mm phone socket, blue, 6 kohm, 2.2 Vpp (for intercom) E Mouse R Serial interface PS/2, green D-SUB, 9 pins, RS232 F Keyboard S Video OUT DVI PS/2, purple Dual-Link (24 + 5), DVI-I, 024 x 76 (video and configuration) G Video IN (-24) T Video OUT (3-4) BNC, 75 Ohm, Vpp, with loop-through, CVBS BNC, 75 Ohm, Vpp, CVBS (same signal as Video OUT and 2 (K)) H Serial interface COM U Not active D-SUB, 9 pins, RS232 2x 3.5 mm phone socket I Parallel interface LTP V Audio IN (-/9-6/7-24) D-SUB, 25-pole, IEEE 24 D-SUB, 5-pole, kohm, 2.2 Vpp (for D-SUB/Cinch adapter cable) J Video OUT VGA W 2V DC OUT Mini-D-SUB, 5-pole, VGA, 024 x 76 (video and configuration) ODU socket, 2-pole, 2V DC K Not active X Mains connection 2x RJ45 IEC C4 socket, 0 / 230 V AC + / 0 %, 50 / 60 Hz L Video OUT (-2) Y Mains switch BNC, 75 Ohm, Vpp, CVBS (only video, no configuration) M USB interface 2x USB 2.0, type A Technical data Dimensions W x H x D Voltage supply Power consumption Heat power Ambient temperature Humidity Atmospheric load Weight Approx. 425 x 22 x 446 mm (without feet) / 425 x 30 x 446 mm (with feet) 0 / 230 V AC + / 0 %, 50 / 60 Hz Max. 30 W Max. 444 BTU/h 5 40 C, C recommended 5 70 % RH, not condensing Dust-free Approx. 0 2 kg 0

11 DMS 0 Bank / 60 Bank / 240 Bank / 240 HSR Bank Assignment of the sockets Contact IN cameras (A) Weidmüller, pins GND 2 Contact 3 Contact 2 Contact IN global (B) Weidmüller, pins GND 2 Contact 3 Contact 2 Relay OUT (C) Weidmüller, 0 pins 4 Contact 3 5 Contact 4 6 Contact 5 Triggering event Type + 2 Relay Recorder in alarm state Normally open Relay 2 None Normally open Relay 3 System error Normally closed 7 + Relay 4 None Normally open Relay 5 More than 0 % of the hold-up tracks occupied Normally open Serial interface (G and Q) D-SUB, 9 pins DCD (Data Carrier Detect) 2 RxD (Receive Data) 3 TxD (Transmit Data) Audio 2 Audio 2 3 Audio 3 4 Audio 4 5 Audio 5 2V DC OUT (w) ODU socket, 2-pole 2V DC 2 GND 4 Contact 3 5 Contact 4 6 Contact 5 4 DTR (Data Terminal Ready) 5 GND 6 DSR (Data Set Ready) Audio IN (V) D-SUB, 5-pole, without D-SUB/Cinch adapter cable 6 Audio 6 7 Audio 7 Audio 9 GND 0 GND 2 7 Contact 6 GND 7 Contact 6 GND GND 3 2 GND 4 3 GND 5 4 GND 6 5 GND RTS (Request to Send) CTS (Clear to Send) 9 RI (Ring Indicator) 2 Serial interface (D) Weidmüller, 2 pins RX+ 2 RX Safety Requirements HDD mounting Mounting DMS Mounting DLS DMS DMS Bank DLS DLS Bank VNS Login DMS Login VNS

12 DLS 4 / / Plus / 6 / 6 Plus Connections The number of the connections can differ depending on the ordered equipment or device variant. The following description refers to a device with full equipment and optional connectors. A B C D E F G H I J K L M N O P Q R S T A Voltage supply 2V DC K Not active ODU socket, 2-pole, 2V DC +/- 5% 3.5 mm phone socket B Serial interface COM 2 L Not active D-SUB, 9 pins, RS mm phone socket C Serial interface COM M Mouse / Keyboard D-SUB, 9 pins, RS232 PS/2 (for mouse / keyboard adapter) D AUX / Line IN N Audio IN (-) 3.5 mm phone socket, 6 kohm, 2.2 Vpp (for intercom) D-SUB, 5-pole, kohm, 2.2 Vpp (for D-SUB/Cinch adapter cable) E Audio OUT O Audio IN (9-6) 3.5 mm phone socket, kohm, 2.2 Vpp (for intercom) D-SUB, 5-pole, kohm, 2.2 Vpp (for D-SUB/Cinch adapter cable) F Video OUT VGA P Video IN (-6) Mini-D-SUB, 5-pole, VGA, 024 x 76 (video and configuration) BNC, 75 Ohm, Vpp, with loop-through, CVBS G Video OUT Q Serial interface BNC, 75 Ohm, Vpp, CVBS (only video, no configuration) Weidmüller, 2 pins, RS45 (for Dallmeier PTZ domes only) H Video OUT 2 R Relay OUT (-5) BNC, 75 Ohm, Vpp, CVBS (only video, no configuration) pins on Weidmüller pins I Ethernet interface S Contact IN global (-6) RJ45, 0/00/000 Mbps 7 pins on Weidmüller pins J USB interface T Contact IN cameras (-6) 4x USB 2.0, type A Weidmüller, pins Technical data Dimensions W x H x D Approx. 425 x x 34 mm (without feet) / 425 x 9 x 34 mm (with feet) Voltage supply 2 V DC + / 5 % Power consumption Max. 70 W Heat power Max. 239 BTU/h Ambient temperature 5 40 C, C recommended Humidity 5 70 % RH, not condensing Atmospheric load Dust-free Weight Approx. 9 0 kg 2

13 DLS 4 / / Plus / 6 / 6 Plus Assignment of the sockets 2V DC IN (A) ODU socket, 2-pole 2V DC 2 GND Serial interface (B and C) D-SUB, 9 pins DCD (Data Carrier Detect) 2 RxD (Receive Data) 3 TxD (Transmit Data) Audio IN (N and O) D-SUB, 5-pole, without D-SUB/Cinch adapter cable Audio 2 Audio 2 3 Audio 3 4 Audio 4 5 Audio 5 6 Audio 6 7 Audio 7 Audio 9 GND 0 GND 2 Relay OUT (R) pins on Weidmüller pins Triggering event Type + 4 Relay Recorder in alarm state Normally open Relay 2 None Normally open 5 + Relay 3 System error Normally closed Relay 4 None Normally open Relay 5 More than 0 % of the secure tracks occupied Normally open 2 GND 3 2 GND 4 3 GND 5 4 GND 6 5 GND GND None None Contact IN global (S) 7 pins on Weidmüller pins Contact 5 Contact 5 3 Contact 3 6 Contact 4 4 Contact 2 7 GND Contact IN cameras (T) Weidmüller, pins Contact 2 GND 3 Contact 3 4 Contact 2 5 Contact 5 6 Contact 4 4 DTR (Data Terminal Ready) 5 GND 6 DSR (Data Set Ready) 7 Contact 7 Contact 6 9 Contact 9 0 Contact Contact 2 Contact 0 Contact 6 3 Contact 3 4 Contact 2 5 Contact 5 6 Contact 4 7 GND Contact 6 Serial interface (Q) Weidmüller, 2 pins RX- 2 RX+ 7 RTS (Request to Send) CTS (Clear to Send) 9 RI (Ring Indicator) Safety Requirements HDD mounting Mounting DMS Mounting DLS DMS DMS Bank DLS DLS Bank VNS Login DMS Login VNS 3

14 DLS 4 Bank Connections The number of the connections can differ depending on the ordered equipment or device variant. The following description refers to a device with full equipment and optional connectors. A B C D E F G H I J K L M N O P Q R S T A Voltage supply 2V DC K Not active ODU socket, 2-pole, 2V DC +/- 5% 3.5 mm phone socket B Serial interface COM 2 L Not active D-SUB, 9 pins, RS mm phone socket C Serial interface COM M Mouse / Keyboard D-SUB, 9 pins, RS232 PS/2 (for mouse / keyboard adapter) D AUX / Line IN N Audio IN (-) 3.5 mm phone socket, 6 kohm, 2.2 Vpp (for intercom) D-SUB, 5-pole, kohm, 2.2 Vpp (for D-SUB/Cinch adapter cable) E Audio OUT O Not active 3.5 mm phone socket, kohm, 2.2 Vpp (for intercom) D-SUB, 5-pole F Video OUT VGA P Video IN (-) Mini-D-SUB, 5-pole, VGA, 024 x 76 (video and configuration) BNC, 75 Ohm, Vpp, with loop-through, CVBS G Video OUT Q Serial interface BNC, 75 Ohm, Vpp, CVBS (only video, no configuration) Weidmüller, 2 pins, RS45 (for Dallmeier PTZ domes only) H Video OUT 2 R Relay OUT (-5) BNC, 75 Ohm, Vpp, CVBS (only video, no configuration) pins on Weidmüller pins I Ethernet interface S Contact IN global (-6) RJ45, 0/00/000 Mbps 7 pins on Weidmüller pins J USB interface T Contact IN cameras (-6) 4x USB 2.0, type A Weidmüller, pins Technical data Dimensions W x H x D Approx. 425 x x 34 mm (without feet) / 425 x 9 x 34 mm (with feet) Voltage supply 2 V DC + / 5 % Power consumption Max. 70 W Heat power Max. 239 BTU/h Ambient temperature 5 40 C, C recommended Humidity 5 70 % RH, not condensing Atmospheric load Dust-free Weight Approx. 9 0 kg 4

15 DLS 4 Bank Assignment od the sockets 2V DC IN (A) ODU socket, 2-pole 2V DC 2 GND Serial interface (B and C) D-SUB, 9-pole DCD (Data Carrier Detect) 2 RxD (Receive Data) 3 TxD (Transmit Data) Audio IN (N) D-SUB, 5-pole, without D-SUB/Cinch adapter cable Audio 2 Audio 2 3 Audio 3 4 Audio 4 5 Audio 5 4 DTR (Data Terminal Ready) 5 GND 6 DSR (Data Set Ready) 6 Audio 6 7 Audio 7 Audio 9 GND 0 GND 2 2 GND 3 2 GND 4 3 GND 5 4 GND 6 5 GND 7 + Serial interface (Q) Weidmüller, 2 pins RX- 2 RX+ 7 RTS (Request to Send) CTS (Clear to Send) 9 RI (Ring Indicator) Relay OUT (R) pins on Weidmüller pins Triggering event Type + 4 Relay Recorder in alarm state Normally open Relay 2 None Normally open 5 + Relay 3 System error Normally closed Relay 4 None Normally open Relay 5 More than 0 % of the hold-up tracks occupied Normally open 2 GND None None Contact IN global (S) 7 pins on Weidmüller pins Contact 5 Contact 5 3 Contact 3 6 Contact 4 4 Contact 2 7 GND Contact IN cameras (T) Weidmüller, pins Contact 2 GND 3 Contact 3 4 Contact 2 5 Contact 5 6 Contact 4 7 Contact 7 Contact 6 9 None 0 Contact None 2 None Contact 6 3 None 4 None 5 None 6 None 7 GND None Safety Requirements HDD mounting Mounting DMS Mounting DLS DMS DMS Bank DLS DLS Bank VNS Login DMS Login VNS 5

16 VNS 6 Connections The number of the connections can differ depending on the ordered equipment or device variant. The following description refers to a device with full equipment and optional connectors. A B C D E F G H I J K L M N O P Q A Voltage supply 2V DC J USB interface ODU socket, 2-pole, 2V DC +/- 5% 4x USB 2.0, type A B Serial interface COM 2 K Not active D-SUB, 9 pins, RS mm phone socket C Serial interface COM L Not active D-SUB, 9 pins, RS mm phone socket D AUX / Line IN M Mouse / Keyboard 3.5 mm phone socket, 6 kohm, 2.2 Vpp (for intercom) PS/2 (for mouse / keyboard adapter) E Audio OUT N Serial interface 3.5 mm phone socket, kohm, 2.2 Vpp (for intercom) Weidmüller, 2 pins, RS45 (for Dallmeier PTZ domes only) F Video OUT VGA O Relay OUT (-5) Mini-D-SUB, 5-pole, VGA, 024 x 76 (only configuration, no video) pins on Weidmüller pins G Not active P Contact IN global (-6) BNC 7 pins on Weidmüller pins H Not active Q Contact IN cameras (-6) BNC Weidmüller pins I Ethernet interface RJ45, 0/00/000 Mbps Technical data Dimensions W x H x D Approx. 425 x x 34 mm (without feet) / 425 x 9 x 34 mm (with feet) Voltage supply 2 V DC + / 5 % Power consumption Max. 60 W Heat power Max. 204 BTU/h Ambient temperature 5 40 C, C recommended Humidity 5 70 % RH, not condensing Atmospheric load Dust-free Weight Approx. 9 0 kg 6

17 VNS 6 Assignment of the sockets 2V DC IN (A) ODU socket, 2 pins 2V DC 2 GND Serial interface (B and C) D-SUB, 9-pole DCD (Data Carrier Detect) 2 RxD (Receive Data) 3 TxD (Transmit Data) 4 DTR (Data Terminal Ready) 5 GND 6 DSR (Data Set Ready) 2 Serial interface (N) Weidmüller, 2 pins RX- 2 RX+ 7 RTS (Request to Send) CTS (Clear to Send) 9 RI (Ring Indicator) Relay OUT (O) pins on Weidmüller pins Triggering event Type + 4 Relay Recorder in alarm state Normally open Relay 2 None Normally open 5 + Relay 3 System error Normally closed Relay 4 None Normally open Relay 5 More than 0 % of the secure tracks occupied Normally open 2 GND None None Contact IN global (P) 7 pins on Weidmüller pins Contact 5 Contact 5 3 Contact 3 6 Contact 4 4 Contact 2 7 GND Contact IN cameras (Q) Weidmüller, pins Contact 2 GND 3 Contact 3 4 Contact 2 5 Contact 5 6 Contact 4 7 Contact 7 Contact 6 9 Contact 9 0 Contact Contact 2 Contact 0 Contact 6 3 Contact 3 4 Contact 2 5 Contact 5 6 Contact 4 7 GND Contact Safety Requirements HDD mounting Mounting DMS Mounting DLS DMS DMS Bank DLS DLS Bank VNS Login DMS Login VNS 7

18 Commissioning and login DMS / DLS Commissioning and login Connect the recorder and relevant peripherals to the voltage supply. Ensure that the VGA monitor and a mouse are connected to the recorder. Switch on the VGA monitor, the peripherals and the recorder. The connected analogue cameras - 4 are displayed after the start. In the initial state it is possible to login without password. The rights of the Administrator group are valid. Note that the definition of the passwords and of the network parameters is necessary for remote access (Dallmeier PView 7 or NetConfig2). Left-click the background. The Recorder login dialogue is displayed. Click Later to login without changing a password. The graphical operation and configuration interface will be displayed. Observe the appropriate Operation and Configuration documentations.

19 Commissioning and login VNS Commissioning and remote login Connect the recorder to the network. Connect the recorder and relevant peripherals to the voltage supply. Switch on the peripherals and the recorder. The recorder is available for remote configuration via Ethernet after the start (up to approx. 5 minutes). Use the following access data: IP address Subnet mask Password Serial number (e.g. DAE ) Commissioning and local login Connect the recorder and relevant peripherals to the voltage supply. Ensure that the VGA monitor and a mouse are connected to the recorder. Switch on the VGA monitor, the peripherals and the recorder. The background image of the configuration interface is displayed after the start. In the initial state it is possible to login without password. The rights of the Administrator group are valid. Note that the definition of the passwords and of the network parameters is necessary for remote access (Dallmeier PView 7 or NetConfig2). Left-click the background. The Recorder login dialogue is displayed. Click Later to login without changing a password. The graphical configuration interface will be displayed. Safety Requirements HDD mounting Mounting DMS Mounting DLS DMS DMS Bank DLS DLS Bank VNS Login DMS Login VNS Observe the appropriate Configuration documentation. 9

20 Information about Copyright, Trademarks, Design Patents 20 Dallmeier electronic The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization is prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design. We reserve the right to make technical modifications. The manufacturer accepts no liability for damage to property or pecuniary damages arising due to minor defects of the product or documentation, e.g. print or spelling errors, and for those not caused by intention or gross negligence of the manufacturer. Dallmeier electronic GmbH & Co.KG Cranachweg 9305 Regensburg, Germany info@dallmeier.com All trademarks identified by are registered trademarks of Dallmeier electronic.