DIS-2/M UTP DIS-2/M NSU DIS-2/M Multi-D HD

Transcription

1 Commissioning English Dallmeier DIS-2/M UTP DIS-2/M NSU DIS-2/M Multi-D HD / /

2 Content Content Validity...2 Conventions...2 Environmental Conditions...2 Safety Instructions...3 Installation Module...4 DIS-2/M UTP... 6 DIS-2/M NSU...7 DIS-2/M Multi-D HD...8 Login... 9 Dimensions...10 Notes...11 Validity This document is valid for the module DIS-2/M UTP, DIS-2/M NSU uad DIS-2/M Multi-D HD. The descriptions in this document are based on the software version 2.5.x.x.x. Conventions This document may contain various warning words and symbols that indicate potential sources of danger. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. NOTICE NOTICE indicates practices for preventing property damage, incorrect configurations or faulty operations. The following symbols and various character formats are used to increase the clearness of the document: Instructions are indicated by arrows ( ). Expressions in bold/italics generally indicate a control element on the device (switches or labels) or on its user interface (buttons, menu entries). Paragraphs in italics provide information on basic principles, special features and efficient procedure as well as general recommendations. Environmental Conditions Unfavourable ambient conditions can shorten the life and cause malfunctions or damages. Do not operate the modules at places with: large scale dust and dirt steam or oil vapours (e.g., kitchen) unsuitable ambient temperatures insufficient ventilation (e.g., closed cabinet) direct sunlight sources of strong heat dissipation (e.g., radiator) sources of strong radiation (e.g., radio transmitter, magnetic field) corrosive surrounding (e.g., gas, salt water) 2

3 Safety Instructions Only use the unit if it is technically in proper working condition and for the intended purpose while keeping safety and potential dangers in mind. Qualified Personnel The installation, mounting, connection, commissioning and configuration of the unit may only be carried out by qualified personnel. This also applies to the maintenance, testing and repair, whereat the regulations of the DIN VDE 0701 series of standards (repair, modification and inspection of electrical appliances) must be followed. Regulations The use of video and audio surveillance systems is, in general, strictly regulated. Inform yourself about the currently valid laws and regulations regarding data, worker and environmental protection before using the unit and ensure compliance with them. System Components Only use internal components that have been tested and approved by Dallmeier. Inappropriate internal components can cause malfunctions, damages and data loss and can result in the loss of warranty. RAID System Devices that are configured with a RAID system for redundant recording always must be supplied with power via an uninterruptable power supply (UPS). A sudden voltage drop can damage the RAID system. Modifications Do not make any modifications to the hardware or software that has not been tested and approved by Dallmeier. Inappropriate modifications can cause malfunctions, damages and data loss and can result in the loss of warranty. Documentation Read the documents included in delivery carefully and thoroughly. Always observe the contained instructions, notes and warnings. Condensation Water If the unit is brought from a cold to a warm environment, resulting condensation water can cause malfunctions and damages. In this case, wait (up to 8 hours) until the unit has reached room temperature before commissioning. Earthing & Equipotential Bonding For the safety of persons (protection against dangerous contact voltages) and devices (protection against overvoltages) and the immunity of information and communication technology equipment to electromagnetic interferences (EMI), all protective measures, which are specified by the currently valid DIN, VDE and ISO standards and which provide for a standard-compliant earthing and a correct equipotential bonding of electrical and electronic devices, are mandatory and must be fulfilled by all means. Lightning Storms To avoid damage to the unit by electrical surge during lightning storms, unplug the unit from the mains power supply (pull out the power plug). This is also recommended, when the unit has been unused for a long period of time. Operating Conditions Unfavourable operating conditions can shorten the life of the unit and can cause malfunctions, damages and data loss and can result in the loss of warranty. Observe the specifications given in the technical data, the operating condition requirements and the maintenance instructions. Shocks Shocks can cause malfunctions and damages. The unit may not be moved while in operation. Foreign Bodies If objects or liquids get into the unit, immediately disconnect it from the power supply (pull out the power plug). Contact the sales partner responsible for your area. Burnt Smell If you notice burnt smell or a formation of smoke coming from the unit, immediately disconnect it from the power supply (pull out the power plug). Contact the sales partner responsible for your area. Opening The housing of the unit may only be opened by qualified personnel for commissioning, inspection, maintenance and repair. Disposal Do not dispose waste electrical and electronic equipment into the household trash. Disconnect the unit from the power supply. Remove all connected devices. Return the unit to your respective sales partner. Introduction UTP NSU Multi-D HD Login Dimensions Notes Safety Instructions Installation Module 3

4 Installation Module Before installing the modules check whether they are integrated in the network via DHCP or which IP addresses are available. NOTICE To prevent network conflicts the IP address or DHCP must be configured after you install each module. A free duct should be available for every module you have ordered. Remove the duct covers from the required ducts. Start on the left-hand side of the module rack. The modules must later be installed in sequence from left to right. Undo the four screws on the duct cover until they are loose in their anchor points. Then remove the cover. WARNING Do not reach into the open housing of the module rack. Do not insert any objects. The module rack is already live. This means that there is a risk of electric shock. To install modules always use the first empty duct from the left-hand side of the module rack. NOTICE Damage to components at risk from electrostatic discharge caused by touching them. Ensure that you are electrostatically discharged (earthed) before you touch the module. Wear suitable ESD shoes or an earth strap. Insert the module into the guide rails (top and bottom). Carefully slide the module into the module rack. Ensure that you slide it straight. Do not use any force. The module is inserted correctly when it has been fully slid in and engaged. The front cover of the module must be flush with the edge of the module rack housing. The module will now already be powering up. 4

5 Installation Module The Error LED will be lit before a video signal has not yet been connected. This does not have a negative effect on the following steps, however. Secure the modle in the module rack using the four screws on the front cover. Connect the module to the PC you wish to use to conficure it via the LAN. A correct connection has been made if the orange LED on the LAN interface is permanently lit. Introduction Safety Instructions The module and PC or laptop can also be connected direct using a cross cable. Configure the IP address or DHCP as described in the Configuration documentation. Then install the next module as described above. Duct Covers For continuous operation it is essential that all ducts on the module rack are closed. This is necessary to maintain air circulation and therefore to cool the modules. Close all the ducts that are still open after you have installed the modules, using the duct covers provided for this purpose. Ensure that the EMC seal on the duct cover is on the right-hand side. If you do not have enough duct covers available, contact the Dallmeier support. Commissioning NOTICE Open ducts on the module rack can result in serious damage to the modules in continuous operation (particularly a hard disk drive failure). WARNING Danger of death from electric shock in the event of a lightning strike! Data transfer and video cables must not be connected or disconnected during a storm. Installation Module Installation Module Multi-D HD NSU Login UTP Dimensions Notes After the mounting in the ready for use module rack the module starts automatically. The power LED flashs. Connect the camera to the module. Connect the module to the network. The module can be configured via the network after approx. 45 seconds. 5

6 Connections DIS-2/M UTP A Contact IN/OUT B LAN (RJ 45) C Video IN/OUT (BNC) D S-Video (mini DIN 4) E UTP/RS 485 F Audio IN/OUT (3,5 mm phone jack) C D A E B F Contact IN/OUT Control inputs (Contact IN) PIN Function 2/4 w/o 6 Contact 1 8 Contact 2 10 Contact 3 12 Contact 4 14/16 GND Relais (Contact OUT) PIN Function 1/3 Relay 1 5/7 Relay 2 9/11 Relay 3 13/15 Relay Relay (Contact OUT) The output relays are floating and galvanically separated. Value Condition Max. Switch capacity max. 12 W Switch voltage DC or peak AC max. 12 V Switch current DC or peak AC max. 1 A UTP/RS485 female connector PIN Function PIN Function 1 UTP Video (+) 5 UTP Audio ( ) 2 UTP Video ( ) 6 RS 485 (B) 3 RS 485 (A) 7 inactive 4 UTP Audio (+) 8 inactive Technical Data Power supply 12 V AC ± 5 % Power consumption Max. 25 W Thermal output Max. 85 BTU/h Temperature +5 C up to +40 C (41 F 104 F) Humidity 5 70 % RH, non-condensing Atmospheric load Dust-free Weight Approx. 2,5 kg (Variant 700 with 2 x HDD) 6

7 Connections DIS-2/M NSU A Contact IN/OUT B LAN (RJ 45) Introduction Contact IN/OUT Control inputs (Contact IN) Relais (Contact OUT) PIN Function PIN Function 2/4 w/o 1/3 Relay 1 6 Contact 1 5/7 Relay 2 8 Contact 2 9/11 Relay 3 10 Contact 3 13/15 Relay 4 12 Contact 4 14/16 GND Relay (Contact OUT) The output relays are floating and galvanically separated. Value Condition Max. Switch capacity max. 12 W Switch voltage DC or peak AC max. 12 V Switch current DC or peak AC max. 1 A A B Safety Installations Instruction Module UTP NSU Multi-D HD Login Dimensions Notes Technical Data Power supply 12 V AC ± 5 % Power consumption Max. 17 W Thermal output Max. 58 BTU/h Temperature +5 C up to +40 C (41 F 104 F) Humidity 5 70 % RH, non-condensing Atmospheric load Dust-free Weight Approx. 2,5 kg (Variant 700 with 2 x HDD) 7

8 Connections DIS-2/M Multi-D HD A Status-LEDs (Error, Alarm, Record, Power) B Video IN (BNC) C Video OUT (S-Video) D Audio OUT (3,5 mm phone-jack) E Serial IO F LAN interface (RJ 45) A B C D E F Serial IO Serial IO is a combined RS485 / RS232 interface. Connection Assignment RS 485 PIN Function 1 GND 2 w/o 3 DA (+) 4 DB ( ) 5 w/o 6 GND Connection Assignment RS 232 PIN Function 1 GND 2 RX 3 w/o 4 w/o 5 TX 6 GND Technical Data Power supply 12 V AC ± 5 % Power consumption Max. 25 W Thermal output Max. 85 BTU/h Temperature +5 C up to +40 C (41 F 104 F) Humidity 5 70 % RH, non-condensing Atmospheric load Dust-free Weight Ca. 2,5 kg (Variant 700 with 2 x HDD) 8

9 Login The configuration is done through the graphical user interface in a browser. System Requirements The following software components are provided: Browser Mozilla Firefox, version 8.x.x or higher or Internet Explorer*) 8 or higher Login Proceed as follows to sign up: The default ip address is , the default password is 3. Start the browser. Enter the required ip address. The login dialogue is displayed. Enter the password. Click the OK button. After successful login, the graphical user interface is displayed in the initial state. Safety Installation Introduction Instructions Module UTP NSU Multi-D HD Login Dimensions Notes Make the required settings (see Configuration documentation). 9

10 Dimensions Variant mm 4.3" 378 mm 14.9" 41 mm 1.6" Variant mm 4.3" 538 mm 21.2" 41 mm 1.6" 10

11 Notes Safety Instructions Installation Module UTP NSU Multi-D HD Login Dimensions Introduction Notes 11

12 Information about Copyright, Trademarks, Design Patents 2012 Dallmeier electronic The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization is prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design. We reserve the right to make technical modifications. The manufacturer accepts no liability for damage to property or pecuniary damages arising due to minor defects of the product or documentation, e.g. print or spelling errors, and for those not caused by intention or gross negligence of the manufacturer. Dallmeier electronic GmbH & Co.KG Cranachweg Regensburg info@dallmeier.com