Hardware news 2015 Miroslav Kocur

Transcription

1 Hardware news 2015 Miroslav Kocur

2 HW newsrtu &HMI Ownproducts

3 Content RTU7C compact unit ELVAC RTU configuration web SMC 133, SMC 144 -class Spower quality analyser ARTIQ 144 -class A power quality analyser High current EP card with measurement and protective functions EP cards with special combinations of inputs ESP7 - signaling panel ERIC151x - signaling and HMI panel EPG7 HP 3-phase generator Soon- RTU7M quality analyser Soon- RTU7M COMIO-PC3 (IEC 61850) Soon- RTU7M-SE

4 RTU7C compact unit Basic features of unit 4 digitalinputs 4 relayoutputs external power supply 10 V DC to 30 V DC communication interfaces GPRS/EDGE/UMTS, Ethernet, RS-232/485 supported communication protocols MODBUS, HIOCom2, IEC , IEC , IEC user programming by logical and relational expressions DIN rail or panel mounting

5 RTU7C compact unit Variant of connection RTU7C with power supply backup

6 RTU7C compact unit Variant of connection RTU7C without power supply backup

7 RTU7C compact unit Typical applications connection of devices without necessary communication(energy meter, etc.) communication protocol converter communication gate dispatching control of small renewable resources counter inputs can reading pulses from energy meter

8 ELVAC RTU configuration web complete settings of RTU7C without SW RTU UC now we are preparing for the next RTU

9 SMC 133, SMC class S power quality analyser ARTIQ class A power quality analyser Basic features of unit Three or four independent voltage and current inputs energy meter supports 3 tariffs single and threephase measurement in four quadrants for active/reactive energy measurement V, I, P, Q, S, harmonic distortion power, PF, cos φ, symetrical components, unbalance factor, THD, 50 harmonics,fundamental harmonics, frequency, active energy, reactive energy 512MB memory for data logging internal battery for 1 hour power backup (only SMC 133) optionally 2 digital input, 2 digital output (only SMC 144) communication interface RS-485, optionally Ethernet or USB communication protocol MODBUS standards IEC , EN50160, class S DIN rail mounting

10 SMC 133, SMC class S power quality analyser ARTIQ class A power quality analyser Measured data can be stored into database and then analyzed and evaluated in SW application ENVIS (free of charge). System cansend regular reports about the power quality in given time period orcan send automatic alarms, if some events exceed the set values.

11 High current EP card with measurement and protective functions 4x voltage and current measurements AC currentrange5a, measuringup to 150 A for1min., max. overload500 A for1s AC voltagerange100 V AC, 230 V AC, etc. 8x DI, 4x DO Protective function, fault records Implementation protections ANSI 50, 51, 67, 50N, 51N, 67N,(EN ) Setting the time-dependent characteristics of protection Setting the directional protection Setting protection - phase or ground Voltage, frequency, unbalance... Protection signals and switch off 16bit a/d converter(greater accuracy and measurement range) calibration constants in the EP card

12 High current EP card with measurement and protective functions ELVAC protection

13 High current EP card with measurement and protective functions 3or4protection in one RTU

14 EP cards with special combinations of inputs EP-3U3I - measuring, indication on low voltage lines 3 voltage inputs 230 V AC 3 current inputs 20 ma AC (1A) fault records protective function implementationprotectionsansi 50, 51, 67, 50N, 51N, 67N (EN ) setting the time-dependent characteristics of protection setting the directional protection setting protection - phase or ground voltage, frequency, unbalance... only signaling fault

15 EP cards with special combinations of inputs EP-3U3I - measuring, indication on low voltage lines, for split-core MTI 20mA

16 EP cards with special combinations of inputs EP card for capacitive sensors VSO 25 3 voltage inputsof this card are optimized for using with sensors VSO 25 Thefourth voltage input Uxis used for measuring of voltage Ua 4 current inputs have nominal range 1 A with measuring upto 30 In thesecards are typically used as control unit andprotection for sectionalizers fault detection (overcurrent, short circuit, current asymmetry, overvoltage, undervoltage, earth fault, incorrect frequency) automatic disconnection in voltage-free pause calibration constants in the EP card

17 EP cards with special combinations of inputs

18 EP cards with special combinations of inputs

19 EP card for RecloserGVR EP cards with special combinations of inputs 3 voltage inputs of this cardare optimized for using with converter 10 kv / 1 V, which ispart of delivery of reclosergvr with capacitive sensors. Thefourthvoltage input Uxis used for measuring of voltage Ua 4 current inputs have nominal range 5 ma with measuring up to 30 In there are available all protective functions, automation functions a recorder of faults, similarly to all other types of EP automatic disconnection in the case of failure, reclosing cards with measuring of 4V 4I calibration constants in the EP card

20 EP cards with special combinations of inputs

21 EP cards with special combinations of inputs

22 EP cards with special combinations of inputs Other EP card for Recloser Tavrida EP cardforsads (FSI 36 and FSU 36 sensors) EP card for Zelisko sensors for Rogowski coil According to customer

23 Panel ESP7-2ETH/F-230 Signaling panel ESP7 panel communicates with RTU via an Ethernet interface. panel is fitted with 22 LED, where the function can be configured using the standard parameterizing software supplied with RTU (RTU User Center) the parameterization is carried out in the expressions editor the RTU FW must be or higher the function of theindividual LED can be set on the basis of the internal statuses ofthertu (digitalinputs, digitaloutputs, analog inputs, virtual analog and digital inputs, internal statuses, etc.) permanenton or off, fastor slow flashing, response delay, etc. can be set for each LED thedescription of the LED functions on the front panel can be changed by the user using insert labels

24 Signaling panel ESP7

25 Basic features of unit Signaling and HMI panel ERIC151x communication with RTU through RS-485 (or Ethernet) external powering 24V DC touchscreen display 2,8 switch for local and remote control RESET button for reset of indication of fault on lines SELECT button for enabling of control of switching element (it is necessary to press two buttons for control which prevents accidental manipulation) indication cross for active line indication indication of outlet earthing indication of fault, the source of fault can be read on display switches On/Off for each switching element

26 Signaling and HMI panel ERIC1516

27 Basic features EPG7 3-phase compact generator three-channel currents generator in range 0 to 45 ma AC and0 to ±60 ma DC in extended version three-channel voltage generator 0 to 7 VAC and 0 to ±10 VDC analog output protection against overloading with indication 4 DI and in extended version 4 DO for tests of protections alphanumeric LCD display and rotary knob with integrated button for easy control powering from NiMH batteries or external adapter integrated fast battery charger USB 2.0 interface with galvanic isolation optional user upgrade of FW according to demanded functionality upper versions of FW can generate fault waveforms obtainedfrom protections (format COMTRADE, proprietary format REC of ELVAC RTU) optional storage of generated waveforms in internal memory upper function for tests of protection functions are in specialized FW operating SW is available for PC

28 EPG7 3-phase compact generator EPG7 waysofusing currents generation, eventually voltage, AC / DC P, Q generation phase to phase voltage setup independent amplitude, frequency, phase setup for individual outputs playing of records from protections (proprietary format REC from ELVAC RTU, COMTRADE) simulator of status of power element, including the interposition optional control and reading of DI/DO protection tests- current, earth, voltage, frequency tests of fault currents indicators test of reclosing test of disconnecting in voltage-free pause multichannel process calibrator

29 EPG7 HP 3-phase generator Basic features expansion of generator EPG7 by power outputs designed for testing the correct function of protection andmeasurements in the standard ranges (100 V, 1 or 5 A) communication between the generator and the power module, transmission of ranges, calibration easy transport in case with wheels the device can be removedand placed on a table currentoutputs: 3 max. 20 A AC voltageoutputs: 3 max. 300 V AC amplitude control: %(signal from EPG7) frequency: Hz (signal from EPG7) angle between phases: (signal from EPG7)

30 EPG7 HP 3-phase generator

31 Summary of SW EPGAP functions User SW for EPG7 - EPGAP operatingparameters setting of generator in remote controlmode, setting of primary and secondary values conversion, generating of V and I user parameters settings of device work with fault records formats REC and COMTRADE records player records storage in device uploading of records from device FW updates support of all EPG7 functions tests of protections and automatics

32 User SW for EPG7 - EPGAP

33 Soon Prepare Communication card RTU7M COMIO-PC3 (2x Ethernet, IEC ParallelRedundancyProtocol) CardforRTU7M -qualityanalysersmc 133 New unit RTU7M-SE

34 O Společnosti Thank you for your attention Hasičská 53, Ostrava - Hrabůvka Czech Republic Tel.: sales@elvac.eu