F-1 Car. Blank. in the Feature Manager and click Sketch from the Content toolbar, Fig. 3. Origin. on the Features toolbar.
|
|
- Shanon Skinner
- 6 years ago
- Views:
Transcription
1 Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. F-1 Car Blank Step 2. Click Part Metric from the list of templates and click OK, Fig. 1. If you are not using SOLIDWORKS templates (you should be) to change units, in the status bar at the bottom right corner of graphics area click Unit System and MMGS, Fig. 2. Or before 2012, click Options on the Standard toolbar and on the Document Properties tab, select Units. B. Body. Step 1. Click Right Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 3. Fig. 1 Step 2. Click Corner Rectangle on the Sketch toolbar. (S) in the Rectangle flyout Fig. 2 Step 3. Draw a rectangle starting at the Origin, Fig. 4. Step 4. Click Smart Dimension Step 5. Add dimensions, Fig. 4. (S) on the Sketch toolbar. Fig. 3 Step 6. Click Zoom to Fit (F) on the View toolbar. Step 7. Click Features on the Command Manager toolbar. Origin Fig. 4 Step 8. Click Extruded Boss/Base on the Features toolbar. SOLIDWORKS 15 Blank F-1 CAR Page 1-1 Cudacountry.net Tech Ed cudacountry@hotmail.com 1/12/15
2 Step 9. In the Property Manager set: under Direction 1, Fig. 5 End Condition Mid Plane Depth 65 C. Save as "BLANK". Step 1. Click File Menu > Save As. Step 2. Key-in BLANK for filename and press ENTER. Fig. 5 Origin Fig. 6 D. Cartridge Hole. Step 1. Click Back on the Standard Views toolbar. (Ctrl-2) Back face Step 2. Click the back face of the body and click Sketch on the Context toolbar, Fig. 7. Step 3. Click Centerline in the Line flyout on the Sketch toolbar. Fig. 7 Step 4. Draw vertical centerline up from Origin, Fig. 8. Step 5. Click Circle on the Sketch toolbar. Step 6. Draw a circle for the cartridge hole on centerline, Fig. 9. Step 7. Click Smart Dimension (S) on the Sketch toolbar. Step 8. Add dimensions, Fig. 10. Origin Fig. 8 Fig. 9 SOLIDWORKS 15 Blank F-1 CAR Page 1-2 Fig. 10
3 Step 9. Click Features on the Command Manager toolbar. Step 10. Click Extruded Cut on the Features toolbar. Step 11. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 12. In the Property Manager set: under Direction 1, Fig. 11 Depth 52 Step 13. Save. Use Ctrl-S. E. Axle Holes. Step 1. Click Right Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 13. Step 2. Click Normal To Fig. 11 Fig. 12 on the Standard Views toolbar. (Ctrl-8) Step 3. Click Circle on the Sketch toolbar. Step 4. Draw two circles for the axle holes, Fig. 14. Fig. 13 Step 5. Click Smart Dimension (S) on the Sketch toolbar. Step 6. Add dimensions, Fig. 15. Fig. 14 Fig. 15 SOLIDWORKS 15 Blank F-1 CAR Page 1-3
4 Step 7. Click Features on the Command Manager toolbar. Step 8. Click Extruded Cut on the Features toolbar. Step 9. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 10. In the Property Manager set: under Direction 1, Fig. 16 End Condition Through All - Both Step 11. Save. Use Ctrl-S. F. Eye Screw Slot. Step 1. Click the front face of the body and click Sketch on the Context toolbar, Fig. 18. Step 2. Click Normal To on the Standard Views toolbar. (Ctrl-8) Fig. 16 Fig. 17 Step 3. Click Center Rectangle Rectangle flyout toolbar. (S) in the on the Sketch Step 4. Draw a rectangle starting at the Origin, Fig. 19. Front face Fig. 18 Step 5. Click Smart Dimension (S) on the Sketch toolbar. Step 6. Add dimensions, Fig. 20. Dimension top of rectangle to Origin. Fig. 19 Origin SOLIDWORKS 15 Blank F-1 CAR Page 1-4 Fig. 20
5 Step 7. Click Features on the Command Manager toolbar. Step 8. Click Extruded Cut on the Features toolbar. Step 9. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 10. In the Cut-Extrude Property Manager set: under Direction 1, Fig. 21 End Condition Through All Step 11. Save. Use Ctrl-S. Fig. 21 Fig. 22 G. Rename Features. Step 1. Rename Features in the Feature Manager. To rename, slowly click twice over the Feature name and change name or use F2 key, Fig. 23 and Fig. 24. Change: Boss-Extrude1 to BODY Cut-Extrude1 to CARTRIDGE HOLE Cut-Extrude2 to AXLE HOLES Cut-Extrude3 to SLOT Change Fig. 23 Fig. 24 SOLIDWORKS 15 Blank F-1 CAR Page 1-5
6 H. Mate References. Step 1. Click Filter Faces (X) on the Selection Filter Fig. 25 toolbar at the bottom of the display, Fig. 25. If necessary, use F5 key to display the toolbar. Step 2. Click Right Plane in the Feature Manager to select Plane, Fig. 26. Step 3. Click Reference Geometry Reference from the menu. on the Features toolbar and Mate Step 4. In the Mate Reference Manager set: under Primary Reference Entity, Fig. 27 Mate Reference Type Coincident Fig. 26 under Secondary Reference Entity click in Entity box and click cylindrical face of front axle hole, Fig. 28 Step 5. Click Right Plane in the Feature Manager to select Plane, Fig. 29. Fig. 28 Step 6. Click Reference Geometry menu. on the Features toolbar and Mate Reference from the Fig. 27 Step 7. In the Mate Reference Manager set: under Primary Reference Entity, Fig. 27 Mate Reference Type under Secondary Reference Entity Coincident click in Entity box and click cylindrical face of rear axle hole, Fig. 30 Fig. 29 Step 8. Save. Use Ctrl-S. Fig. 30 SOLIDWORKS 15 Blank F-1 CAR Page 1-6
7 I. Material Balsa. Step 1. Turn off Filter Faces (X) on the Selection Filter toolbar at the bottom of the display or use F6 key to turn off all filters, Fig. 31. Fig. 31 Step 2. Right click Material Edit Material, Fig. 32. in the Feature Manager and click Step 3. Expand Woods (click the +) in the material tree and select Balsa, Fig. 33. Click Apply and Close. Step 4. Save. Use Ctrl-S. Fig. 32 Fig. 33 Fig. 34 SOLIDWORKS 15 Blank F-1 CAR Page 1-7
8 J. Enable PhotoView 360. Step 1. If necessary, turn on PhotoView 360, click the flyout of Options Ins. on the Standard toolbar and click Add- Step 2. In the dialog box find PhotoView 360 and place a check in the check box under Active Add-Ins and Start-Up. Click OK, Fig. 35. K. Rotate Mapping. Step 1. Click PhotoView 360 Menu > Edit Appearance. Step 2. In the Property Manager set: click Mapping tab, Fig. 36 Fig. 35 under Mapping Controls click Surface mapping Rotation 90 click Small mapping size Step 3. Save. Use Ctrl-S. Fig. 37 Fig. 36 SOLIDWORKS 15 Blank F-1 CAR Page 1-8
Blank. Chapter 1. CO2 Rail Car. A. New Metric Part. Step 1. Click File Menu > New. B. Body. Step 1. Click Right Plane
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. CO2 Rail Car Blank Step 2. Click Part Metric from the list and click OK, Fig. 1. If you are not using SolidWorks templates (you should be),
More informationSolar Car. Chassis. in the Feature Manager and click Sketch from the Content toolbar, Fig. 2. Origin. on the Command Manager toolbar. Fig.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Solar Car Chassis Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Chassis. Step 1. Click Right Plane in the Feature Manager and click
More informationPanel. Chapter 16. Solar Car. A. Sketch. Step 1. Click File Menu > New, click Part and OK. B. Save as "PANEL". Step 1. Click File Menu > Save As.
Chapter 16 Solar Car Panel A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Center
More informationBody. Chapter 1. Simple Machines. A. New Part. Step 1. Click File Menu > New.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Simple Machines Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature
More informationSimple Machines. Body. Step 4. Start at Origin and sketch the 8 lines, Fig. 2. Fig. 1. Origin
Chapter 1 Simple Machines Body A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1. Step 3. Click
More informationWheel GT-F. Chapter 5. CO2 Shell Car. A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK.
Chapter 5 CO2 Shell Car Wheel GT-F A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1.
More informationSimple Machines. Wheel. in the Feature Manager and click Sketch. on the Command Manager toolbar.
Chapter 3 Simple Machines Wheel A. Wheel. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step 3. Click
More informationCO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar.
CO 2 Shell Car Chapter 2 Body A. Save as "BODY". Step 1. If necessary, open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY for the filename and press ENTER. B. FRONT Wheel Shell.
More informationSpeedway. Body. (S) on the Sketch toolbar. Fig. 1
Chapter 1 A. New Part. Step 1. Click File Menu > New. Speedway Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature Manager
More informationBattery Holder 2 x AA
Chapter 22 JSS Battery Holder 2 x AA A. Front Extrude. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Context toolbar,
More informationBoat. Battery Holder AA
Chapter 9 Boat Battery Holder AA A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch context toolbar, Fig. 1. Step 3. Click
More informationCO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig.
Chapter 17 CO2 Shell Car Axle Retainer A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationJSS. Ping Pong Ball. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Sketch toolbar.
Chapter 18 JSS Ping Pong Ball A. Half Circle Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig.
More informationBody. Chapter 2. CO2 Rail Car E. A. Save as "BODY RAIL E". Step 1. Open your BLANK file.
Chapter 2 A. Save as "BODY RAIL E". Step 1. Open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY RAIL E for the filename and press ENTER. CO2 Rail Car E Body B. Appearance. Step
More informationF1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the
Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.
More informationChair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane.
Chapter 7 A. 3D Sketch. Step 1. If necessary, open your CHAIR file. Chair Top Rail Step 2. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 3. Zoom in around top of back leg, Fig. 1. To zoom,
More informationDelta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar.
Chapter 6 Delta Dart Socket A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step
More informationDelta IV Heavy. Interstage. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Command Man- on the Features
Chapter 4 Delta IV Heavy Interstage A. Sketch Circles. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationNose Cone. Chapter 4. Rocket 3D Print. A. Revolve. Step 1. Click File Menu > New, click Part and OK. SOLIDWORKS 16 Nose Cone ROCKET 3D PRINT Page 4-1
Chapter 4 Rocket 3D Print Nose Cone A. Revolve. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step
More informationTerminal. Chapter 16. E-Car. A. Component from Design Library. SOLIDWORKS 17 Terminal E-CAR Page 16-1
Chapter 16 E-Car Terminal A. Component from Design Library. Step 1. Click the Design Library tab in the Task Pane (right side of graphics area), Fig. 1. Step 2. Expand routing and click electrical folder
More informationBoat. Hull. Step 4. Sketch point directly above the Origin, Fig. 2. Use the inferencing line, the dotted line that appears when you sketch the point.
Chapter 1 Boat Hull A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step 3. Click Point on
More informationSkateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line
Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step
More informationSkateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2
Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationBattery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
More informationRocket 1. Fin. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig. 1. Fig. 2
Chapter 2 Rocket 1 Fin A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Line
More informationClay. Chapter 9. Glider. A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. C. Sketch. Step 1. Click the side face of the
More informationGlider. Clay. Fig. 1 Side face. Step 5. In the Convert Entities Property Manager: click side face, Fig. 3 click OK twice, Fig. 3. Fig. 3.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. Step 2. Click the side face of the Fuselage,
More informationH Stab and V Stab. Chapter 6. Glider. A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file.
Chapter 6 Glider H Stab and V Stab A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in H STAB for the filename and press ENTER. B. Sketch
More informationTail Hook. Chapter 14. Airplane. A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK.
Chapter 14 Airplane Tail Hook A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right (plane) in the Feature Manager and click Sketch from the Content toolbar,
More informationPropeller. Chapter 13. Airplane. A. Base for Blade. Step 1. Click File Menu > New, click Part and OK.
Chapter 13 Airplane Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch toolbar, Fig. 1. from the Content Step
More informationDelta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.
Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationWheels and Axle. Chapter 7. Simples Machines. A. Save As. Step 1. If necessary, open your Track Assembly 15 file. B. Insert Truck Assembly.
Chapter 7 Simples Machines Wheels and Axle A. Save As. Step 1. If necessary, open your Track Assembly 15 file. Step 2. Click File Menu > Save As. Step 3. Key-in WHEELS AND AXLE ASSEMBLY for the filename
More informationCO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.
Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.
More informationCO2 Car Assembly. in the Property Manager to place the part at the origin, Fig. 1. on the Assemblies toolbar. SolidWorks Assembly CO2 CAR Page 8-1
Chapter 8 CO2 Car Assembly A. Insert Axles and Wheels. Step 1. Click File Menu > New, click Assembly Metric and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the
More informationSpring Assembly. in the Begin Assembly Property. on the Standard toolbar and click Add-Ins.
Chapter 2 Spring Assembly A. Create New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Cancel Manager. in the Begin Assembly Property B. Enable Toolbox Browser. Step 1. If
More informationMastercam X9 for SOLIDWORKS
Chapter 21 CO2 Shell Car Mastercam X9 for SOLIDWORKS A. Enable Mastercam for SOLIDWORKS. Step 1. If necessary, turn on Mastercam for SOLIDWORKS, click the flyout of Options on the Standard toolbar and
More informationFuselage and Sharks Tooth
Chapter 4 Glider Fuselage and Sharks Tooth A. Save as "FUSELAGE". Step 1. Open your FUSELAGE BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in FUSELAGE for the filename and press ENTER. B.
More informationAssembly Motion Study
Penny Hockey Chapter 10 Assembly Motion Study A. Rename Penny Mate. Step 1. Open your PENNY HOCKEY ASSEMBLY file. Step 2. Expand Mates in the Feature Manager and select the last Mate, Fig. 1. This should
More informationPenny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam Step 1. If necessary, save your BASE file in SOLIDWORKS.
Mastercam 2017 Chapter 22 Chapter 7 Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam 2017. Step 1. If necessary, save your BASE file in SOLIDWORKS. Step 2. In Mastercam 2017, click
More informationMemo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet.
Commands Used New Part This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Click File, New on the standard toolbar. Select Part from the New SolidWorks
More informationGlider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar.
Chapter 5 Glider Wing 4 Panel Tip A. Open and Save As "WING 4 PANEL". Step 1. Open your WING BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in WING 4 PANEL for the filename and press ENTER.
More informationFlow Sim. Chapter 12. F1 Car. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 12 F1 Car Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar and
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 21 CO2 Shell Car Mastercam X6 for SolidWorks Toolpaths A. Enable Mastercam for SolidWorks. Step 1. If necessary, turn on Mastercam for SolidWorks, click Tools Menu > Add-Ins. Step 2. In the dialog
More informationSOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering
SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now
More informationIntroduction to SolidWorks Basics Materials Tech. Wood
Introduction to SolidWorks Basics Materials Tech. Wood Table of Contents Table of Contents... 1 Book End... 2 Introduction... 2 Learning Intentions... 2 Modelling the Base... 3 Modelling the Front... 10
More informationFlow Sim. Chapter 16. Airplane. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 Airplane Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar
More informationBottle Rocket. Drawing. on the Com- on the View Layout
Chapter 6 Bottle Rocket Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing Metric and OK. on the Com- Step 2. Click View Layout mand Manager toolbar. Step 3. Click Model View toolbar.
More informationAirplane Assembly. SolidWorks 10 ASSEMBLY AIRPLANE Page 9-1
Chapter 9 A. Insert Parts. Airplane Assembly Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the Property Manager,
More informationPhotoView 360 Decals
Chapter 10 Glider PhotoView 360 Decals A. Enable PhotoView 360. Step 1. If necessary, open your GLIDER ASSEMBLY file. Step 2. If necessary, turn on PhotoView 360. Click Tools Menu > Add- Ins. Click to
More informationIntroduction to SolidWorks for Technology. No1: Childs Toy
Introduction to SolidWorks for Technology No1: Childs Toy Table of Contents Table of Contents... 1 Introduction... 2 Part Modelling: Cab... 3 Part Modelling: Base... 6 Part Modelling: Wheel... 12 Assembly:
More informationSpeedway. Motion Study. on the Standard toolbar and click Add-Ins. at the lower
Chapter 8 Speedway Motion Study A. Enable SOLIDWORKS Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, enable Motion, click the flyout of Options on the Standard toolbar
More informationSpeedway. Motion Study. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click Tools Menu > Add-Ins.
Chapter 8 Speedway Motion Study A. Enable SolidWorks Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click
More informationCatamaran A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N).
Mastercam 07 Chapter 6 Catamaran A. Create Rectangle. Step. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step. On the Wireframe tab click Rectangle. Step
More informationBelt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 35 Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click Rectangle.
More informationBottom Truss ANALYSIS
Chapter 3 Beam Bottom Truss ANALYSIS A. Enable SolidWorks Simulation. Step 1. If necessary, open your Beam1 part file. Step 2. If necessary, turn on SolidWorks Simulation. To turn on Solid- Works Simulation,
More informationSOLIDWORKS 2018 Reference Guide
SOLIDWORKS 2018 Reference Guide A comprehensive reference guide with over 250 standalone tutorials David C. Planchard, CSWP, SOLIDWORKS Accredited Educator SDC PUBLICATIONS Better Textbooks. Lower Prices.
More informationChapter 36. Mastercam Jewelry Box Fixture. A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 36 Jewelry Box Fixture A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe
More informationFlow Sim. Chapter 16. Airplane. A. Add-In. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 A. Add-In. Step 1. If necessary, open your ASSEMBLY file. Airplane Flow Sim Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in
More informationChapter 39. Mastercam Jewelry Box Tray. A. Sketch Tray Circle. B. Twin Edge Point Circles. Mastercam 2017 Tray Jewelry Box Page 39-1
Mastercam 2017 Chapter 39 A. Sketch Tray Circle. Jewelry Box Tray Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click
More informationFig. 2 Mastercam 2020 Spinning Top SW 19 to MCam20 TOOLPATHS Page 13-1
Mastercam 2020 Chapter 13 Spinning Top SOLIDWORKS 19 to Mastercam 2020 A. Open File in Mastercam 2020. Step 1. If necessary, save your Handle and Flywheel parts file in SOLIDWORKS. Step 2. In Mastercam
More informationBoat Hull Solid. (Alt-2). in ribbon bar to fix and close ribbon Fig. 3 Mastercam X7 BOAT HULL SOLID Page 29-1
Mastercam X7 Chapter 29 A. Open Boat Block File. Step 1. Open your BOAT BLOCK file. Boat Hull Solid B. Save As BOAT HULL SOLID Step 1. Click File Menu > Save As. Step 2. Key-in BOAT HULL SOLID for the
More informationDrawing. Chapter 12. Beam. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View. on the View Layout toolbar.
Chapter 12 Beam Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationDrawing. Chapter 10. Airplane. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager.
More informationSOLIDWORKS: Lesson 1 - Basics and Modeling. UCF Engineering
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals UCF Engineering SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment for
More informationSolidWorks 2013 and Engineering Graphics
SolidWorks 2013 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following
More informationCudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1
Mastercam 2017 Chapter 19 Cudacountry Radial A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New QAT. (Ctrl-N) on the Quick Access Toolbar Step 2. On the Wireframe tab click
More informationSolidWorks 2008 Tutorial. with MultiMedia CD. A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling
INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects with MultiMedia CD A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard
More informationAirplane Drawing. Chapter 10. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse Step 4. Select your AIRPLANE
More informationJewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3
Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in
More informationDrawing. Chapter 11. Bridge. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. on the View Layout toolbar.
Chapter 11 Bridge Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationAirplane. Chapter 21. Mastercam A. Create Rectangle. B. Save As AIRPLANE. C. Set Grid and Snap.2. Mastercam 2017 Airplane Page 21-1
Mastercam 2017 Chapter 21 A. Create Rectangle. Airplane Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step 2. On the Wireframe tab click Rectangle.
More informationSOLIDWORKS 2016 and Engineering Graphics
SOLIDWORKS 2016 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
More informationME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.
PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step
More informationSOLIDWORKS: Lesson 1 - Basics and Modeling. Introduction to Robotics
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals Introduction to Robotics SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment
More informationProject 3. Top Down Design In Context. Below are the desired outcomes and usage competencies based upon the completion of this Project.
Assembly Modeling with SolidWorks Project 3 Below are the desired outcomes and usage competencies based upon the completion of this Project. Project Desired Outcomes: 2AXIS-TRANSFER Assembly. PLATE-B Part.
More informationChapter 3. CO2 Car SolidWorks to Mastercam. A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks.
Chapter 3 CO2 Car SolidWorks to Mastercam X 2007 A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box scroll
More informationExport DXF to CorelDRAW
Chapter 13 Glider Export DXF to CorelDRAW A. Export Fuselage/Tooth Sketch as DXF". Step 1. Open your FUSELAGE part file. Step 2. Roll the rollback bar to below the Cut-Extrude1. To rollback, click Fillet1
More informationChapter 1. SolidWorks Overview
Chapter 1 SolidWorks Overview Objectives: When you complete this chapter you will: Have a good background knowledge of SolidWorks Have learnt how to start a SolidWorks session Understand the SolidWorks
More informationChapter 4 Feature Design Tree
4-1 Chapter 4 Feature Design Tree Understand Feature Interactions Use the FeatureManager Design Tree Modify and Update Feature Dimensions Perform History-Based Part Modifications Change the Names of Created
More informationFlow Sim. Chapter 14 P-51. A. Set Up. B. Create Flow Simulation Project. Step 1. Click Flow Simulation. SolidWorks 10 Flow Sim P-51 Page 14-1
Chapter 14 A. Set Up. P-51 Flow Sim Step 1. If necessary, open your ASSEMBLY file. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in the
More informationFig. 1. Fig. 1. on the Standard Views toolbar. SolidWorks ASSEMBLY AIRPLANE Page 8-1
Chapter 8 Airplane Assembly A. Insert Set of Parts. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click View Menu > Origins to display the origin. Step 3. Click Keep Visible in the Property
More informationSolidworks tutorial. simulation. Author : M.Ghasemi. Contact us: solidworksadvisor.com
Solidworks tutorial simulation Author : M.Ghasemi Contact us: info @ solidworksadvisor.com This time we are going to use the solidworks simulation to analyze a chair leg. We all have seen a chair like
More informationSolidworks Tutorial #1: How to create USB head
This Solidworks tutorial composes using the exact format and delivery as Solidworks 2008/2009 Tutorials : Beginner e-book. Solidworks Tutorial #1: How to create USB head You can find almost all PC devices
More informationChapter 11 Solar Car Drawing
Chapter 11 Solar Car Drawing A. Insert Top and Side Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Browse Step 3. Select your solar car assembly file and click Open. Step 4.
More information3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD
3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions
More informationSolidWorks 2009 & DCG Student Assignment
SolidWorks 2009 & DCG Student Assignment RD10 DCG Design & Communication Graphics 1 SolidWorks 2009 & DCG Student Assignment Table of Contents Focus of the lesson. 3 Getting Started Modelling the TV Plate
More informationVisit the following websites to learn more about this book:
Assembly Modeling Model Files Initial and Final Solutions! with SolidWorks 2012 For the SolidWorks user who needs to understand Assembly modeling By Planchard & Planchard CSWP SDC SSoolliiddW Woorrkkss
More informationParametric Modeling Design and Modeling 2011 Project Lead The Way, Inc.
Parametric Modeling Design and Modeling 2011 Project Lead The Way, Inc. 3D Modeling Steps - Sketch Step 1 Sketch Geometry Sketch Geometry Line Sketch Tool 3D Modeling Steps - Constrain Step 1 Sketch Geometry
More informationThe Fundamentals of SolidWorks Featuring the VEXplorer robot with over 40 integrated stand-alone tutorials
INSIDE: Tutorial Model Files On CD The Fundamentals of SolidWorks 2007 Featuring the VEXplorer robot with over 40 integrated stand-alone tutorials David C. Planchard & Marie P. Planchard, CSWP SDC PUBLICATIONS
More informationSolidWorks 2½D Parts
SolidWorks 2½D Parts IDeATe Laser Micro Part 1b Dave Touretzky and Susan Finger 1. Create a new part In this lab, you ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select
More informationLearning. Modeling, Assembly and Analysis SOLIDWORKS Randy H. Shih SDC. Better Textbooks. Lower Prices.
Learning SOLIDWORKS 2016 Modeling, Assembly and Analysis Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites
More informationSOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users
SOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users The premium provider of learning products and solutions www.cadartifex.com Table of Contents Dedication... 3 Preface... 15 Part 1. Introducing
More informationExport DXF to Illustrator
Chapter 12 Glider Export DXF to Illustrator A. Export Fuselage/Tooth Sketch as DXF". Step 1. Open your FUSELAGE part file. Step 2. Roll the rollback bar to below the Cut-Extrude1. To rollback, click Fillet1
More informationInventor 201. Work Planes, Features & Constraints: Advanced part features and constraints
Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the
More informationToolpaths for Fuselage
Mastercam 2017 Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Hide Top Surface. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. On the Home tab click Hide/Unhide
More informationCHANNEL BLOCK SOLID. Step 7. For the Placement Point, click the bottom left gray rectangle and click OK. to fit drawing on the screen.
Chapter 9 CHANNEL BLOCK SOLID A. Create Rectangle. Step 1. Change to the Front View. Use green Front View or ALT-6 F. Hold down ALT and press 6. Key-in F. Step 3. Create. Step 4. Rectangle. Step 5. 1 Point.
More informationContains all new training videos for SolidWorks 2014 SolidWorks 2014 Tutorial with Video Instruction. Better Textbooks. Lower Prices.
Videos Contains all new training videos for SolidWorks 2014 SolidWorks 2014 Tutorial with Video Instruction A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard, CSWP, SolidWorks
More informationSolidWorks Intro Part 1b
SolidWorks Intro Part 1b Dave Touretzky and Susan Finger 1. Create a new part We ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select File New Templates IPSpart If the SolidWorks
More informationParametric Modeling with SOLIDWORKS 2017
Parametric Modeling with SOLIDWORKS 2017 NEW Contains a new chapter on 3D printing Covers material found on the CSWA exam Randy H. Shih Paul J. Schilling SDC PUBLICATIONS Better Textbooks. Lower Prices.
More information