Mastercam X6 for SolidWorks Toolpaths
|
|
- Gabriel Jones
- 5 years ago
- Views:
Transcription
1 Chapter 21 CO2 Shell Car Mastercam X6 for SolidWorks Toolpaths A. Enable Mastercam for SolidWorks. Step 1. If necessary, turn on Mastercam for SolidWorks, click Tools Menu > Add-Ins. Step 2. In the dialog box scroll down to Mastercam for SolidWorks and place a check in the check box under Active Add-Ins and Start-Up, Fig. 1. Click OK. B. Rotate Body. Step 1. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 2. Click Insert Menu > Features > Move/ Copy. Step 3. In the Property Manager set: under Options click Translate/Rotate button under Bodies to Move/Copy, Fig. 2 click CO2 car body, Fig. 3 under Rotate X Rotation Origin 0 Y Rotation Origin 0 Z Rotation Origin 0 Fig. 2 Origin Body Fig. 1 Y Rotation Angle 90 press Tab key on keyboard, Fig. 3 click OK. Fig. 3 C. Create Containment Sketch. Step 1. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 4. Step 2. Click Normal To on the Standard Views toolbar. (Ctrl-8) Fig. 4 4/20/12 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-1 Cudacountry.net Tech Ed cudacountry@hotmail.com
2 Step 3. Click Rectangle Sketch toolbar. (S) on the Step 4. Starting directly below the cartridge hole and aligned with bottom of the body, draw a rectangle up to outside the top of body and out short of the front tip of nose as shown in Fig. 5. Fig. 5 Fix point at (-305, 0) Step 5. Right click drawing and click Select from menu to unselect Rectangle tool. Step 6. Click the bottom rear corner of the rectangle to select the corner Point, Fig. 5. Step 7. In the Point Property Manager set: X Coordinate -305 Y Coordinate 0 click Fix, Fig. 6 click OK. Fig. 6 Step 8. Click Smart Dimension (S) on the Sketch toolbar. Step 9. Dimension front of rectangle to tip of body 6 as shown in Fig. 7. Fig. 7 Step 10. Click Exit Sketch on the Sketch toolbar. Step 11. Rename Sketch to CONTAINMENT SKETCH, Fig. 8. To rename sketch, click the Sketch at bottom of the Feature Manager. Press F2 on keyboard and key-in CONTAINMENT SKETCH. Step 12. Save. Use Ctrl-S. Fig. 8 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-2
3 D. Create LEFT CUT View. Step 1. Rotate view as shown in Fig. 9. Hold down middle mouse button (wheel) and drag to rotate view. Step 2. Press the Space Bar on the keyboard to display the Orientation dialog box. Drag the dialog box to the top left corner of the drawing area, Fig. 10. Fig. 9 Step 3. Click Pin/UnPin in Orientation dialog box to pin the dialog box, Fig. 10. Fig. 11 Step 4. Click New View to display Named View dialog, Fig. 10. Step 5. In the New View dialog box key-in LEFT CUT and click OK, Fig. 11. Later, to display new LEFT CUT view, double click LEFT CUT, Fig. 12. Fig. 12 E. Create LEFT CUT WCS and Tool Plane. Fig. 10 Step 1. Click View Manager on the Mastercam toolbar. Step 2. Click MASTERCAM FRONT view from list of named views in the View Manager dialog box, Fig. 13. Step 3. Click Create From button in the View Manager dialog box, Fig. 13. Fig. 13 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-3
4 Step 4. In the Define View Property Manager, Fig. 14 under New View Geometry in the View name box, key-in LEFT CUT under Orientation Options set About X to 180º click in other About box confirm rotation of Mastercam Origin, Fig. 15. BEFORE rotating Origin AFTER rotating Origin 180º click OK. Step 5. Set Origin (in view coordinates): X to -305 Y to -34 Z to 34, Fig. 16. Fig. 14 Fig. 15 Step 6. Click the Set All button, Fig. 16. Step 7. Click OK. Step 8. Confirm axis moved and rotated, Fig. 17. Step 9. Save. Use Ctrl-S. F. Create BOTTOM CUT View. Step 1. Rotate view as shown in Fig. 18. Hold down middle mouse button (wheel) and drag to rotate view. Fig. 16 LEFT CUT Mastercam Origin Step 2. Click New View to display Named View dialog, Fig. 19. Fig. 17 Step 3. In the New View dialog box key-in BOTTOM CUT and click OK, Fig. 20. Later, to display this new BOTTOM CUT view, double click BOT- TOM VIEW, Fig. 19. Fig. 19 Fig. 20 Fig. 18 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-4
5 G. Create BOTTOM CUT WCS and Tool Plane. Step 1. Click View Manager on the Mastercam toolbar. Step 2. Click MASTERCAM BOT- TOM view from list of named views in the View Manager dialog box, Fig. 21. Step 3. Click Create From button in the View Manager dialog box, Fig. 21. Step 4. In the Define View Property Manager, Fig. 22 in the View name box key-in BOTTOM CUT Fig. 21 set About Z to 180º click in another About box confirm rotation of Mastercam Origin, Fig. 23 click OK. Step 5. Set Origin (in view coordinates): X to -305 Y to 0 Z to 0, Fig. 24. Fig. 22 Fig. 23 Step 6. Click the Set All button and click OK. Step 7. Confirm axis moved and rotated, Fig. 25. Step 8. Save. Use Ctrl-S. BOTTOM CUT Mastercam Origin Fig. 24 Fig. 25 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-5
6 H. Stock Setup. Step 1. Click Mastercam Toolpaths Manager tab in the Property Manager, Fig. 26. Step 2. Expand Properties (click the +) in the Toolpaths Manager, Fig. 26. Step 3. Click Stock Setup in the Toolpaths Manager, Fig. 26. in the Machine Group Properties dia- Step 4. Click Stock View button log, Fig. 27. Fig. 26 Step 5. Click BOTTOM CUT in the View Selection dialog, Fig. 28 and click OK. Step 6. Click left rear corner of the red part to set it as the stock origin, Fig. 27. Step 7. Set Stock Origin coordinates: X to 0 Y to -21 Z to 0, Fig. 27. Step 8. Set X-Y-Z dimensions: X to 305 Y to 42 Z to 70, Fig. 27. Step 9. Click OK in the Machine Group Properties, Fig. 29. Step 10. Save. Use Ctrl-S. Click corner to move arrow Fig. 27 Fig. 28 Fig. 29 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-6
7 I. REAR SHELL Rough Area Clearance HST Surface Toolpath. Step 1. Click 3D High Speeds Toolpaths on the Mastercam toolbar and Area Clearance from the menu. Step 2. Click OK in the NC name dialog, Fig. 30. Fig. 30 Step 3. Click Filter Solids on the Selection Filter toolbar at the bottom of the display, Fig. 31. If necessary, use F5 key to display the toolbar. Fig. 31 Step 4. In the Selection Property Manager set: under Faces and Bodies click the solid body, Fig. 33 click OK. Body solid Expand Containment Curves and Edges, Fig. 34. Click in the Containment Curves and Edges box, Fig. 34. Check Propagate along tangent edges, Fig. 34. Click an edge of rear wheel shell, Fig. 35, the edges will change color when selected. Fig. 32 Fig. 33 Containment chain Click Filter Solids to turn OFF on the Selection Filter toolbar at the bottom of the display, Fig. 36. Fig. 35 Click OK when done. Fig. 34 Fig. 36 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-7
8 Step 5. Select Tool from the tree control and: click Select library tool button, Fig. 37. Step 6. Click the Filter button, Fig. 38. Step 7. Click None button under Tool Types, Fig. 39. Step 8. Click Endmill2 Sphere button (second button top row), Fig. 39 and click OK. Fig. 37 Step 9. Click 240 Ball Endmill 6mm, Fig. 40 and click OK. Fig. 38 Fig. 39 Fig. 40 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-8
9 Step 10. Back in Tool page set: Tool # 1 Head # 1 Feed rate 300 Plunge rate 200 Fig. 41. Step 11. Select Cut Parameters from the tree control and set: Cutting method Climb Stepdown 12.5 Fig. 41 Tool containment Compensate to: Inside uncheck Add offset distance to tool radius XY stepover Minimum 2 Maximum 3 Stock to leave on walls and floors 1 Fig. 42. Fig. 42 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-9
10 Step 12. Select Trochoidal motion from the tree control and set: Minimize burial Fig. 43. Step 13. Select Transitions from the tree control and set: Entry helix Radius 3 Fig. 44. Fig. 43 Fig. 44 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-10
11 Step 14. Select Steep/ Shallow from the tree control and set: Check Z depths Minimum -9 Maximum -35 Fig. 45. Step 15. Select Linking Parameters from the tree control and set: Clearance plane 0 Absolute Part clearance 0 Fig. 45 Negative -9 Negative -35 All Leads 0 Fig. 46. Step 16. Click OK Step 17. Watch the toolpath progress at the bottom right corner of the display. Step 18. Save. Use Ctrl-S.. Fig. 46 Fig. 47 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-11
12 J. Verify REAR SHELL Rough Area Clearance. Step 1. Click Verify in the Toolpaths Manager, Fig. 48. Step 2. Click Machine quickly, Fig. 49. Step 3. Turn on Simulate tool. Fig. 48 Step 4. Click Play machining. Step 5. Click OK dialog box. start to close Verify K. FRONT SHELL Rough Area Clearance HST Surface Toolpath. Step 1. Toggle toolpath display in Toolpaths Manager to turn off toolpath display, Fig. 51. Step 2. Copy Roughing toolpath in the Toolpaths Manager. To copy, hold right mouse button and drag the Surface High Speed toolpath down under the operations. Release the mouse button and click Copy After from menu, Fig. 51. Step 3. Expand the copied 2 - Surface High Speed, expand Geometry and click Geometry - Containment, Fig. 52. Step 4. In the Selection Property Manager set: Right click Edge1 in Curves and Edges box and click Clear Selection, Fig. 53 Click an edge of front wheel shell, Fig. 54 Click OK. Fig. 54 Fig. 53 Step 5. In the Toolpaths Manager, click Regenerate all dirty operations, Fig. 52. Step 6. Save. Use Ctrl-S. Fig. 50 Fig. 51 Fig. 49 Fig. 52 Containment chain SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-12
13 L. BOTH SHELLS Finish Raster HST Toolpath. Step 1. Copy the second Roughing toolpath in the Toolpaths Manager. To copy, hold with the right mouse button and drag the Surface High Speed toolpath down under the operations. Release the mouse button and click Copy After from menu, Fig. 55. Step 2. Expand 3 - Surface High Speed and click Parameters, Fig. 56. Step 3. Select Toolpath Type from the tree control and select: Finishing Raster Fig. 57. Step 4. Under Containment, click Select containment boundaries button, Fig. 57. Step 5. In the Selection Property Manager: Click an edge of rear wheel shell, Fig. 58. You should have two edges selected, edge of rear and front shells, Fig. 59. Click OK. Containment chain Fig. 55 Fig. 56 Fig. 57 Fig. 58 Fig. 59 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-13
14 Step 6. Select Cut Parameters from the tree control and set: Cutting method Zigzag Stepover.5 Tool containment Compensate to: Inside Check Add offset distance to tool radius Stock to leave on walls and floors 0 Fig. 60. Fig. 60 Step 7. Select Steep/ Shallow from the tree control and set: Uncheck Z depths Fig. 61. Step 8. Click OK. Fig. 61 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-14
15 M. Verify Finish BOTTOM CUT. Step 1. In the Toolpaths Manager, click Regenerate all dirty operations, Fig. 62. Step 2. Watch the toolpath progress at the bottom right corner of the display. Step 3. Click Toolpath Group1 in the Toolpaths Manager to select all three toolpaths, Fig. 62. in the Toolpaths Man- Step 4. Click Verify ager, Fig. 63. Step 5. Click Play in Verify dialog box to start machining. Step 6. Click OK Fig. 62 Fig. 63 to close Verify dialog box. Fig. 64 N. Set-up Toolpath Groups. Step 1. Rename Toolpath Group 1 to WHEEL SHELLS. To Rename group, right click Toolpath Group 1 and click Groups > Rename from the menu, Fig. 65. Step 2. Key-in WHEEL SHELLS for new group name, Fig. 66. Fig. 65 Fig. 66 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-15
16 Step 3. Insert a new Toolpath group. To insert group, right click Machine Group 1 at the very top and click Groups > New Toolpath group from the menu, Fig. 67. Step 4. Key-in SIDE CUTS for Group name, Fig. 68. Step 5. Save. Use Ctrl-S. Fig. 67 O. Finish Scallop LEFT CUT HST Surface Toolpath. Step 1. Double click LEFT CUT in Orientation dialog box to change to your left cut view, Fig. 69. Fig. 68 Step 2. Click View Manager on the Mastercam toolbar. Step 3. Click LEFT CUT view from list of named views in View Manager dialog box, Fig. 70. Fig. 69 Step 4. Click Set All button OK, Fig. 70. and Step 5. Click 3D High Speeds Toolpaths on the Mastercam toolbar and Scallop from the menu. Step 6. Click Filter Solids on the Selection Filter toolbar at the bottom of the display, Fig. 71. If necessary, use F5 key to display the toolbar. Fig. 70 Fig. 71 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-16
17 Step 7. In the Selection Property Manager set: under Faces and Bodies click the solid body, Fig. 73 click OK. Body solid Click Filter Solids to turn OFF on the Selection Filter toolbar at the bottom of the display, Fig. 74. Fig. 72 Fig. 73 Click Filter Sketches on the Selection Filter toolbar, Fig. 74. Fig. 74 Expand Containment Curves and Edges, Fig. 75. Click in the Containment Curves and Edges box, Fig. 75. Click any line of the CON- TAINMENT SKETCH in the drawing, Fig. 76. Click Filter Sketches to turn OFF on the Selection Filter toolbar, Fig. 77. Fig. 75 Containment Sketch Fig. 76 Click OK when done. Fig. 77 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-17
18 Step 8. Select Tool from the tree control and select: Feed rate 300 Plunge rate 200 Fig. 78. Step 9. Select Cut Parameters from the tree control and set: Cutting method Zigzag Stepover 1 Tool containment Compensate to: Center Fig. 78 Stock to leave on walls and floors 0 Fig. 79. Fig. 79 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-18
19 Step 10. Select Steep/ Shallow from the tree control and set: Use Z depths Minimum 0 Maximum -37 Fig. 80. Step 11. Select Arc Filter/Tolerance from the tree control and set: Total tolerance.0625 click Refine toolpath button, Fig. 81. Fig. 80 Negative -37 Fig. 81 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-19
20 Step 12. In the Refine Toolpath dialog box set: Fig. 82 Check Line/Arc Filtering Setting Set Minimum arc radius.0625 Uncheck Create arcs XY check box Check One way filtering Move NC program length slider to Short. Step 13. Click OK Step 14. Click OK in Refine Toolpath dialog box. in Scallop dialog box. Step 15. Watch the toolpath progress at the bottom right corner of the display. Fig. 82 Step 16. Save. Use Ctrl-S. P. Verify Finish LEFT CUT. Step 1. Click 4 - Surface High Speed Scallop in the Toolpaths Manager to select toolpath, Fig. 83. in the Toolpaths Man- Step 2. Click Verify ager, Fig. 83. Step 3. Click the Play in the Verify dialog box to start the machining. Step 4. Click OK close Verify dialog box. to Fig. 84 Fig. 83 Fig. 85 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-20
21 Q. Mirror LEFT CUT to RIGHT CUT Scallop Toolpath. Step 1. Click Toolpath Transform on the Mastercam toolbar. Step 2. Under Type, select Mirror, Fig. 86. Step 3. Under Source operations, select Surface High Speed (Scallop), Fig. 86. Step 4. Click Mirror tab at the top of dialog box, Fig. 86. Fig. 86 Step 5. Under Mirror, select Mirror about X axis, Fig. 87. Step 6. Click OK in the Transform Operation Params dialog box. R. Verify RIGHT CUT. Step 1. In the Toolpaths Manager, click the Transform by Coordinate - Mirror about X axis toolpath, Fig. 88. Fig. 87 Step 2. Click Verify in the Toolpaths Manager. Step 3. Click the Play Verify dialog box. in the Fig. 89 Step 4. Click OK to close Verify. Step 5. Save. Use Ctrl-S. Fig. 88 SolidWorks 12 MCX6 for SW Toolpaths CO2 SHELL CAR Page 21-21
Mastercam X9 for SOLIDWORKS
Chapter 21 CO2 Shell Car Mastercam X9 for SOLIDWORKS A. Enable Mastercam for SOLIDWORKS. Step 1. If necessary, turn on Mastercam for SOLIDWORKS, click the flyout of Options on the Standard toolbar and
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.
More informationPenny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam Step 1. If necessary, save your BASE file in SOLIDWORKS.
Mastercam 2017 Chapter 22 Chapter 7 Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam 2017. Step 1. If necessary, save your BASE file in SOLIDWORKS. Step 2. In Mastercam 2017, click
More informationBelt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 35 Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click Rectangle.
More informationToolpaths for Fuselage
Mastercam 2017 Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Hide Top Surface. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. On the Home tab click Hide/Unhide
More informationToolpaths for Boat. OptiRough and Finish Waterline. Step 8. Click OK in the Machine Group Properties, Fig. 2. Stock display Click corner to move arrow
Mastercam 2017 Chapter 33 Toolpaths for Boat A. Machine Type and Stock Setup. Step 1. If necessary, open your BOAT ROUND BOTTOM. Step 2. If necessary, display Toolpaths Manager. On the View tab click (Alt-O).
More informationToolpaths for Fuselage
Mastercam Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Machine Type and Stock Setup. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. If necessary, display
More informationFig. 2 Mastercam 2020 Spinning Top SW 19 to MCam20 TOOLPATHS Page 13-1
Mastercam 2020 Chapter 13 Spinning Top SOLIDWORKS 19 to Mastercam 2020 A. Open File in Mastercam 2020. Step 1. If necessary, save your Handle and Flywheel parts file in SOLIDWORKS. Step 2. In Mastercam
More informationJewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3
Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in
More informationChapter 39. Mastercam Jewelry Box Tray. A. Sketch Tray Circle. B. Twin Edge Point Circles. Mastercam 2017 Tray Jewelry Box Page 39-1
Mastercam 2017 Chapter 39 A. Sketch Tray Circle. Jewelry Box Tray Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click
More informationChapter 36. Mastercam Jewelry Box Fixture. A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 36 Jewelry Box Fixture A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe
More informationCO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar.
CO 2 Shell Car Chapter 2 Body A. Save as "BODY". Step 1. If necessary, open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY for the filename and press ENTER. B. FRONT Wheel Shell.
More informationSpeedway. Body. (S) on the Sketch toolbar. Fig. 1
Chapter 1 A. New Part. Step 1. Click File Menu > New. Speedway Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature Manager
More informationTRAINING GUIDE MILL-LESSON-FBM-1 FBM MILL AND FBM DRILL
TRAINING GUIDE MILL-LESSON-FBM-1 FBM MILL AND FBM DRILL Mastercam Training Guide Objectives Previously in Mill-Lesson-6 and Mill-Lesson-7 geometry was created and machined using standard Mastercam methods.
More informationChair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane.
Chapter 7 A. 3D Sketch. Step 1. If necessary, open your CHAIR file. Chair Top Rail Step 2. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 3. Zoom in around top of back leg, Fig. 1. To zoom,
More informationBody. Chapter 2. CO2 Rail Car E. A. Save as "BODY RAIL E". Step 1. Open your BLANK file.
Chapter 2 A. Save as "BODY RAIL E". Step 1. Open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY RAIL E for the filename and press ENTER. CO2 Rail Car E Body B. Appearance. Step
More informationBody. Chapter 1. Simple Machines. A. New Part. Step 1. Click File Menu > New.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Simple Machines Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature
More informationSimple Machines. Body. Step 4. Start at Origin and sketch the 8 lines, Fig. 2. Fig. 1. Origin
Chapter 1 Simple Machines Body A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1. Step 3. Click
More informationMASTERCAM DYNAMIC MILLING TUTORIAL. June 2018
MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject
More informationH Stab and V Stab. Chapter 6. Glider. A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file.
Chapter 6 Glider H Stab and V Stab A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in H STAB for the filename and press ENTER. B. Sketch
More informationPanel. Chapter 16. Solar Car. A. Sketch. Step 1. Click File Menu > New, click Part and OK. B. Save as "PANEL". Step 1. Click File Menu > Save As.
Chapter 16 Solar Car Panel A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Center
More informationBattery Holder 2 x AA
Chapter 22 JSS Battery Holder 2 x AA A. Front Extrude. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Context toolbar,
More informationF-1 Car. Blank. in the Feature Manager and click Sketch from the Content toolbar, Fig. 3. Origin. on the Features toolbar.
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. F-1 Car Blank Step 2. Click Part Metric from the list of templates and click OK, Fig. 1. If you are not using SOLIDWORKS templates (you should
More informationTerminal. Chapter 16. E-Car. A. Component from Design Library. SOLIDWORKS 17 Terminal E-CAR Page 16-1
Chapter 16 E-Car Terminal A. Component from Design Library. Step 1. Click the Design Library tab in the Task Pane (right side of graphics area), Fig. 1. Step 2. Expand routing and click electrical folder
More informationTOOLPATHS TRAINING GUIDE. Sample. Distribution. not for MILL-LESSON-4-TOOLPATHS DRILL AND CONTOUR
TOOLPATHS TRAINING GUIDE MILL-LESSON-4-TOOLPATHS DRILL AND CONTOUR Mill-Lesson-4 Objectives You will generate a toolpath to machine the part on a CNC vertical milling machine. This lesson covers the following
More informationFlow Sim. Chapter 12. F1 Car. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 12 F1 Car Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar and
More informationDelta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.
Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationGlider. Clay. Fig. 1 Side face. Step 5. In the Convert Entities Property Manager: click side face, Fig. 3 click OK twice, Fig. 3. Fig. 3.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. Step 2. Click the side face of the Fuselage,
More informationSkateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line
Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step
More informationCO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.
Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step
More informationBlank. Chapter 1. CO2 Rail Car. A. New Metric Part. Step 1. Click File Menu > New. B. Body. Step 1. Click Right Plane
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. CO2 Rail Car Blank Step 2. Click Part Metric from the list and click OK, Fig. 1. If you are not using SolidWorks templates (you should be),
More informationFuselage and Sharks Tooth
Chapter 4 Glider Fuselage and Sharks Tooth A. Save as "FUSELAGE". Step 1. Open your FUSELAGE BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in FUSELAGE for the filename and press ENTER. B.
More informationBoat. Battery Holder AA
Chapter 9 Boat Battery Holder AA A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch context toolbar, Fig. 1. Step 3. Click
More informationBrief Introduction to MasterCAM X4
Brief Introduction to MasterCAM X4 Fall 2013 Meung J Kim, Ph.D., Professor Department of Mechanical Engineering College of Engineering and Engineering Technology Northern Illinois University DeKalb, IL
More informationSkateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2
Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationChapter 3. CO2 Car SolidWorks to Mastercam. A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks.
Chapter 3 CO2 Car SolidWorks to Mastercam X 2007 A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box scroll
More informationSolar Car. Chassis. in the Feature Manager and click Sketch from the Content toolbar, Fig. 2. Origin. on the Command Manager toolbar. Fig.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Solar Car Chassis Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Chassis. Step 1. Click Right Plane in the Feature Manager and click
More informationTRAINING GUIDE. Sample Only. not to be used. for training MILL-LESSON-15 CORE ROUGHING, WATERLINE, AND SURFACE FINISH LEFTOVER
TRAINING GUIDE MILL-LESSON-15 CORE ROUGHING, WATERLINE, AND SURFACE FINISH LEFTOVER Mastercam Training Guide Objectives You will use a provided model for Mill-Lesson-15, then generate the toolpaths to
More informationCO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig.
Chapter 17 CO2 Shell Car Axle Retainer A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationTRAINING GUIDE MILL-LESSON-FBM-2 FBM MILL AND FBM DRILL
TRAINING GUIDE MILL-LESSON-FBM-2 FBM MILL AND FBM DRILL Mastercam Training Guide Objectives This lesson will use the same Feature Based Machining (FBM) methods used in Mill-Lesson- FBM-1, how ever this
More informationBoat. Hull. Step 4. Sketch point directly above the Origin, Fig. 2. Use the inferencing line, the dotted line that appears when you sketch the point.
Chapter 1 Boat Hull A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step 3. Click Point on
More informationFlow Sim. Chapter 16. Airplane. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 Airplane Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar
More informationBattery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
More informationTail Hook. Chapter 14. Airplane. A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK.
Chapter 14 Airplane Tail Hook A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right (plane) in the Feature Manager and click Sketch from the Content toolbar,
More informationBoat Hull Solid. (Alt-2). in ribbon bar to fix and close ribbon Fig. 3 Mastercam X7 BOAT HULL SOLID Page 29-1
Mastercam X7 Chapter 29 A. Open Boat Block File. Step 1. Open your BOAT BLOCK file. Boat Hull Solid B. Save As BOAT HULL SOLID Step 1. Click File Menu > Save As. Step 2. Key-in BOAT HULL SOLID for the
More informationJSS. Ping Pong Ball. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Sketch toolbar.
Chapter 18 JSS Ping Pong Ball A. Half Circle Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig.
More informationFlow Sim. Chapter 14 P-51. A. Set Up. B. Create Flow Simulation Project. Step 1. Click Flow Simulation. SolidWorks 10 Flow Sim P-51 Page 14-1
Chapter 14 A. Set Up. P-51 Flow Sim Step 1. If necessary, open your ASSEMBLY file. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in the
More information4 & 5 Axis Mill Training Tutorials. To order more books: Call or Visit or Contact your Mastercam Dealer
4 & 5 Axis Mill Training Tutorials To order more books: Call 1-800-529-5517 or Visit www.inhousesolutions.com or Contact your Mastercam Dealer Mastercam X Training Tutorials 4 & 5 Axis Mill Applications
More informationGlider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar.
Chapter 5 Glider Wing 4 Panel Tip A. Open and Save As "WING 4 PANEL". Step 1. Open your WING BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in WING 4 PANEL for the filename and press ENTER.
More informationCudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1
Mastercam 2017 Chapter 19 Cudacountry Radial A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New QAT. (Ctrl-N) on the Quick Access Toolbar Step 2. On the Wireframe tab click
More informationFlow Sim. Chapter 16. Airplane. A. Add-In. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 A. Add-In. Step 1. If necessary, open your ASSEMBLY file. Airplane Flow Sim Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in
More informationWheel GT-F. Chapter 5. CO2 Shell Car. A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK.
Chapter 5 CO2 Shell Car Wheel GT-F A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1.
More informationIntroduction to the Work Coordinate System (WCS) April 2015
Introduction to the Work Coordinate System (WCS) April 2015 Mastercam X9 Introduction to WCS TERMS OF USE Date: April 2015 Copyright 2015 CNC Software, Inc. All rights reserved. Software: Mastercam X9
More informationRocket 1. Fin. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig. 1. Fig. 2
Chapter 2 Rocket 1 Fin A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Line
More informationMill Level 1 Training Tutorial
To order more books: Call 1-800-529-5517 or Visit www.inhousesolutions.com or Contact your Mastercam dealer Mastercam X 5 Copyright: 1998-2010 In-House Solutions Inc. All rights reserved Software: Mastercam
More informationAirplane Assembly. SolidWorks 10 ASSEMBLY AIRPLANE Page 9-1
Chapter 9 A. Insert Parts. Airplane Assembly Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the Property Manager,
More informationWheels and Axle. Chapter 7. Simples Machines. A. Save As. Step 1. If necessary, open your Track Assembly 15 file. B. Insert Truck Assembly.
Chapter 7 Simples Machines Wheels and Axle A. Save As. Step 1. If necessary, open your Track Assembly 15 file. Step 2. Click File Menu > Save As. Step 3. Key-in WHEELS AND AXLE ASSEMBLY for the filename
More informationDelta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar.
Chapter 6 Delta Dart Socket A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step
More informationNose Cone. Chapter 4. Rocket 3D Print. A. Revolve. Step 1. Click File Menu > New, click Part and OK. SOLIDWORKS 16 Nose Cone ROCKET 3D PRINT Page 4-1
Chapter 4 Rocket 3D Print Nose Cone A. Revolve. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step
More informationF1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the
Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.
More informationBottle Rocket. Drawing. on the Com- on the View Layout
Chapter 6 Bottle Rocket Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing Metric and OK. on the Com- Step 2. Click View Layout mand Manager toolbar. Step 3. Click Model View toolbar.
More informationClay. Chapter 9. Glider. A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. C. Sketch. Step 1. Click the side face of the
More informationCADCAM using Powermill
CADCAM using Powermill In this exercise you will create the toolpaths necessary to machine the Cowling model. Create a folder on your h: called Powermill. Inside this create a folder called cowling2009.
More informationSpeedway. Motion Study. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click Tools Menu > Add-Ins.
Chapter 8 Speedway Motion Study A. Enable SolidWorks Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click
More informationTRAINING GUIDE. Sample not. for Distribution LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
More informationIntroduction to MasterCAM X4,7
Introduction to MasterCAM X4,7 Spring 2014 By Meung J. Kim, Ph.D., Professor Department of Mechanical Engineering Northern Illinois University 1 Preliminaries C-Plane: flat Construction plane that can
More informationChapter 11 Solar Car Drawing
Chapter 11 Solar Car Drawing A. Insert Top and Side Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Browse Step 3. Select your solar car assembly file and click Open. Step 4.
More informationVERO UK TRAINING MATERIAL. 2D CAM Training
VERO UK TRAINING MATERIAL 2D CAM Training Vcamtech Co., Ltd 1 INTRODUCTION During this exercise, it is assumed that the user has a basic knowledge of the VISI-Series software. OBJECTIVE This tutorial has
More informationDelta IV Heavy. Interstage. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Command Man- on the Features
Chapter 4 Delta IV Heavy Interstage A. Sketch Circles. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationAssembly Motion Study
Penny Hockey Chapter 10 Assembly Motion Study A. Rename Penny Mate. Step 1. Open your PENNY HOCKEY ASSEMBLY file. Step 2. Expand Mates in the Feature Manager and select the last Mate, Fig. 1. This should
More informationDrawing. Chapter 11. Bridge. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. on the View Layout toolbar.
Chapter 11 Bridge Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationTRAINING GUIDE. Sample. Distribution. not for LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
More informationDynamic Milling. March 2015
Dynamic Milling March 2015 Mastercam X9 Dynamic Milling TERMS OF USE Date: March 2015 Copyright 2015 CNC Software, Inc. All rights reserved. Software: Mastercam X9 Use of this document is subject to the
More informationAutodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Tim Varner - 2004 The Inventor User Interface Command Panel Lists the commands that are currently
More informationSpeedway. Motion Study. on the Standard toolbar and click Add-Ins. at the lower
Chapter 8 Speedway Motion Study A. Enable SOLIDWORKS Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, enable Motion, click the flyout of Options on the Standard toolbar
More informationTRAINING GUIDE WCS - VIEW MANAGER - PART-2
TRAINING GUIDE WCS - VIEW MANAGER - PART-2 Mastercam Training Guide Objectives The learner will create the geometry and toolpaths for WCS-Part-2. This Lesson will cover the following topics: Create a 3-dimensional
More informationPropeller. Chapter 13. Airplane. A. Base for Blade. Step 1. Click File Menu > New, click Part and OK.
Chapter 13 Airplane Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch toolbar, Fig. 1. from the Content Step
More informationWhat s new in EZCAM Version 18
CAD/CAM w w w. e z c a m. com What s new in EZCAM Version 18 MILL: New Curve Machining Wizard A new Curve Machining Wizard accessible from the Machining menu automates the machining of common part features
More informationSpring Assembly. in the Begin Assembly Property. on the Standard toolbar and click Add-Ins.
Chapter 2 Spring Assembly A. Create New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Cancel Manager. in the Begin Assembly Property B. Enable Toolbox Browser. Step 1. If
More informationTRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
More informationExercise Guide. Published: August MecSoft Corpotation
VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4
More information5 Axis Cutting Using Delcam Powermill Written by: John Eberhart DM Lab Tutorial
5 Axis Cutting Using Delcam Powermill Written by: John Eberhart DM Lab Tutorial This tutorial covers how to setup a job for a Multi-Axis Toolpath specifi cally using the Robot. Note: You need to follow
More informationAirplane Drawing. Chapter 10. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse Step 4. Select your AIRPLANE
More informationMemo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet.
Commands Used New Part This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Click File, New on the standard toolbar. Select Part from the New SolidWorks
More informationSimple Machines. Wheel. in the Feature Manager and click Sketch. on the Command Manager toolbar.
Chapter 3 Simple Machines Wheel A. Wheel. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step 3. Click
More informationINTRODUCTION TO MULTIAXIS TOOLPATHS
INTRODUCTION TO MULTIAXIS TOOLPATHS June 2017 INTRODUCTION TO MULTIAXIS TOOLPATHS June 2017 2017 CNC Software, Inc. All rights reserved. Software: Mastercam 2018 Terms of Use Use of this document is subject
More informationDrawing. Chapter 12. Beam. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View. on the View Layout toolbar.
Chapter 12 Beam Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationCO2 Car Assembly. in the Property Manager to place the part at the origin, Fig. 1. on the Assemblies toolbar. SolidWorks Assembly CO2 CAR Page 8-1
Chapter 8 CO2 Car Assembly A. Insert Axles and Wheels. Step 1. Click File Menu > New, click Assembly Metric and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the
More information3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD
3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions
More informationDrawing. Chapter 10. Airplane. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager.
More informationCHAPTER 1. EZ-MILL PRO / 3D MACHINING WIZARD TUTORIAL 1-2
1. TABLE OF CONTENTS 1. TABLE OF CONTENTS 1 CHAPTER 1. EZ-MILL PRO / 3D MACHINING WIZARD TUTORIAL 1-2 Overview... 1-2 Cavity Machining... 1-2 Basic Programming Steps... 1-3 The Part... 1-4 Setting the
More informationBottom Truss ANALYSIS
Chapter 3 Beam Bottom Truss ANALYSIS A. Enable SolidWorks Simulation. Step 1. If necessary, open your Beam1 part file. Step 2. If necessary, turn on SolidWorks Simulation. To turn on Solid- Works Simulation,
More informationAutodesk Fusion 360 Training: The Future of Making Things Attendee Guide
Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Abstract After completing this workshop, you will have a basic understanding of editing 3D models using Autodesk Fusion 360 TM to
More informationAirplane. Chapter 21. Mastercam A. Create Rectangle. B. Save As AIRPLANE. C. Set Grid and Snap.2. Mastercam 2017 Airplane Page 21-1
Mastercam 2017 Chapter 21 A. Create Rectangle. Airplane Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step 2. On the Wireframe tab click Rectangle.
More informationCNC Programming Simplified. EZ-Turn / TurnMill Tutorial.
CNC Programming Simplified EZ-Turn / TurnMill Tutorial www.ezcam.com Copyright Notice This manual describes software that contains published and unpublished works of authorship proprietary to EZCAM Solutions,
More informationPhotoView 360 Decals
Chapter 10 Glider PhotoView 360 Decals A. Enable PhotoView 360. Step 1. If necessary, open your GLIDER ASSEMBLY file. Step 2. If necessary, turn on PhotoView 360. Click Tools Menu > Add- Ins. Click to
More informationMASTERCAM WIRE TUTORIAL. June 2018
MASTERCAM WIRE TUTORIAL June 2018 MASTERCAM WIRE TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject to the Mastercam End
More informationVisualCAM 2018 for SOLIDWORKS-TURN Quick Start MecSoft Corporation
2 Table of Contents Useful Tips 4 What's New 5 Videos & Guides 6 About this Guide 8 About... the TURN Module 8 Using this... Guide 8 Getting Ready 10 Running... VisualCAM for SOLIDWORKS 10 Machining...
More informationCHANNEL BLOCK SOLID. Step 7. For the Placement Point, click the bottom left gray rectangle and click OK. to fit drawing on the screen.
Chapter 9 CHANNEL BLOCK SOLID A. Create Rectangle. Step 1. Change to the Front View. Use green Front View or ALT-6 F. Hold down ALT and press 6. Key-in F. Step 3. Create. Step 4. Rectangle. Step 5. 1 Point.
More informationTraining Guide CAM Basic 1 Getting Started with WorkNC
Training Guide CAM Basic 1 Getting Started with WorkNC Table of Contents Table of Contents 1 Training Guide Objectives 1-1 2 Introduction 2-1 2.1 Part Geometry Preparation 2-1 2.2 Starting WorkNC 2-2
More information