Client Instructions - ID Tech Configuration Instructions

Transcription

1 Client Instructions - ID Tech Configuration Instructions Please follow the steps below to get started with the configuration process for your ID Tech reader. A student ID card will be necessary for the setup. You may contact your Client Relations Manager at any time if you have any questions. STEP ONE: If you have not downloaded the software used to configure this card reader, please do so now using this link. STEP TWO: Open Notepad by going to the Windows Start button -> All Programs -> Accessories -> Notepad. Swipe in the card in Notepad (to see if it s perfect). This scans what s on card on all tracks. Make sure to keep Notepad open you will need it to test with during the configuration process. STEP THREE: Define which track the Student ID is on. (Trial and Error) 1. Go to the Configuration Software, and ensure that the reader is plugged in. Click on Change Basic Reader Settings. 2. Click on the Track Settings tab at the top of the page. Now you will check each track to find out which one contains the student ID. For example select Track 1 Only then make sure to click Send to MSR to add this setting to your card reader (test using Notepad). Continue this until you determine the correct track.

2 STEP FOUR: Define Formula 1. Once the track is determined, then figure out if it is pulling more info than needed and where the Student ID is: a. Example: ; b. Formula will be 4 offset characters, starting with a semicolon (;) and going for 9 characters 2. Click Change Advanced Reader Settings button and select the Data Editing tab.

3 3. Select Enable under the Data Edit. 4. Select the Custom option from Data Format. 5. Click Add Formula

4 A new box will open, click New Custom Field Select your track number, and click the radio button for After String

5 Next you will be adding in the actual formula. Here is a breakdown of what each field in this section means: 1. Times: This is the number of times you want the string to repeat you will enter 1 2. String: This is identifying the character that begins your string 3. Offset: This is the number of characters after (and not including) the character entered into the String field, that your ID number begins a. NOTE: Do not count either the character in the string field OR the first character of your ID number when getting this number 4. Length: This is just the number of characters in your ID number Example: The entries in the screenshot below will turn this: ; into this: Click Add then click Ok

6 Now you will see your formula in the Customized Fields box double click on it and it will move down into the Sent Sequences box below. Next click New Added Fields

7 Select \cr in the Non-Printable drop-down. Click Add then click Ok Now you will see your formula in the Added Fields box - double click on it and it will move down into the Sent Sequences box below. Click Ok and click Send to MSR. Test in notepad to ensure that it appears correctly!

8 Troubleshooting Tips! If at any point the card reader stops reading anything go to Change Basic Reader Settings and click Default All. This will return to default settings and then just start over. Don t forget to download settings again! STEP FIVE: If setting up multiple readers, follow these steps. 1. Follow the steps above to setup the first reader 2. Click on the Save to File button. 3. Plug in the second reader and click Send to MSR. Repeat for each reader. 4. If you come back at a later date open the configuration manager and click Load From File and search for the file you saved! If you are sending the configuration file to another colleague, then they need to: 1. Install the reader software 2. Save this file to their computer to the same location yours is saved 3. Make sure the swipe reader (USB) is plugged in 4. Click on the OPEN file icon tab to select the formula file (the configuration file you sent them) 5. Click DOWNLOAD (Red Arrow pointing down) to upload the configuration settings to the new swipe reader FAQ when downloading data -- When saving you might see this, which just means it s downloading:

9 FAQ when you don t know where the formula is and you are setting up additional readers: 1. Install Configuration software 2. Plug in a configured reader (to pull the formula) 3. Click Upload Settings 4. Unplug configured reader; Plug in unconfigured reader 5. Click Download Settings a. Note: You can save the configuration text file to this computer, but it s not necessary.