0.1. [0x8A] Read Configuration

Transcription

1 0.1. [0x8A] Read Configuration The Read Configuration Protocol is defined to query the complete or parts of reader configuration. This protocol is an extension of [0x80] Read Configuration and realizes many improvements: 1. several destinations are addressable 2. one, multiple or all configuration blocks can be read 3. the address range is up to configuration blocks for each destination 4. different configuration locations for each destination are addressable 5. several block sizes are supported 6. protocol ignores read protected configuration blocks and returns only readable configuration blocks Reader: x02 LENGTH COM-ADR [0x8A] DEVICE BANK MODE CFG-ADR CFG-N CRC16 Reader x02 LENGTH COM-ADR [0x8A] STATUS 7 8 9, byte CFG-N BLOCK- SIZE CFG-ADR CFG-DATA CRC16 Repeated CFG-N times FEIG ELECTRONIC GmbH Seite 1 von 9

2 DEVICE: The DEVICE identifies the target controller inside the reader. The following devices are acceptable: DEVICE AC-Controller Value BANK: The BANK addresses a specified memory bank of the target device. The following banks are acceptable: BANK Value Note Main 0x01 For RF-independent settings MODE: The MODE controls the command. The following flags are defined: ALL LOC LOC: ALL: specifies the location of the configuration block b000 RAM b001 EEPROM specifies to read the complete configuration from RAM or EEPROM b0 configuration to be read specified by CFG-ADR and CFG-N b1 read complete configuration. CFG-ADR and CFG-N ignored FEIG ELECTRONIC GmbH Seite 2 von 9

3 CFG-ADR: In Request protocol: First block address of the required configuration blocks. In Response protocol: block address of the following configuration data which builds together a dataset, repeated CFG-N times. CFG-N: In Request protocol: Number of configuration blocks to be read. In Response protocol: Number of returned datasets which consists of a block address and related configuration data. BLOCKSIZE: Number of bytes in each configuration block. CFG-DATA: Returned configuration data. STATUS: Hex-value General 0x00 OK: Data / parameters have been read or stored without error Control command has been executed 0x02 Read Error Read of configuration block failed internally 0x11 Parameter-Range-Error The range of values for one or more parameters were exceeded 0x15 Read Protect This status is returned only if one configuration block (CFG-N = 1) is to be read and the configuration block at this block address is reserved for future use FEIG ELECTRONIC GmbH Seite 3 von 9

4 0.2. [0x8B] Write Configuration The Write Configuration Protocol is defined to change the complete or parts of reader configuration. This protocol is an extension of [0x81] Write Configuration and realizes four improvements: 1. several destinations are addressable 2. one, multiple or all configuration blocks can be written 3. the address range is up to configuration blocks for each destination 4. different configuration locations for each destination are addressable 5. several block sizes are supported 6. protocol ignores write protected configuration blocks and writes only writable configuration blocks Reader: x02 LENGTH COM-ADR [0x8B] DEVICE BANK , byte MODE CFG-N BLOCK- SIZE CFG-ADR CFG-DATA CRC16 Repeated CFG-N times Reader (STATUS = 0x00) x02 LENGTH COM-ADR [0x8B] 0x00 CRC16 FEIG ELECTRONIC GmbH Seite 4 von 9

5 DEVICE: The DEVICE identifies the target controller inside the reader. The following devices are acceptable: DEVICE AC-Controller Value BANK: The BANK addresses a specified memory bank of the target device. The following banks are acceptable: BANK Value Note Main 0x01 For RF-independent settings MODE: The MODE controls the command. The following flags are defined: LOC LOC: specifies the location of the configuration block b000 RAM b001 RAM and EEPROM CFG-N: Number of configuration blocks. BLOCKSIZE: Number of bytes in each configuration block. CFG-ADR: Block address of the related configuration block. CFG-DATA: Configuration block with each BLOCKSIZE bytes related to CFG-ADR. FEIG ELECTRONIC GmbH Seite 5 von 9

6 STATUS: Hex-value General 0x00 OK: Data / parameters have been read or stored without error Control command has been executed Write Error Write of configuration block failed internally 0x11 Parameter-Range-Error: The range of values for one or more parameters were exceeded 0x16 Write Protect This status is returned only if one configuration block (CFG-N = 1) is to be written and the configuration block at this block address is reserved for future use FEIG ELECTRONIC GmbH Seite 6 von 9

7 0.3. [0x8C] Reset Configuration The Reset Configuration Protocol is defined to set the complete or parts of reader configuration to factory default values. This protocol is an extension of [0x84] Reset Configuration and realizes three improvements: 1. several destinations are addressable 2. one, multiple or all configuration blocks can be reset 3. the address range is up to configuration blocks for each destination 4. different configuration locations for each destination are addressable 5. protocol ignores write protected configuration blocks and resets only writable configuration blocks Reader: x02 LENGTH COM-ADR [0x8C] DEVICE BANK MODE CFG-ADR CFG-N CRC16 Reader x02 LENGTH COM-ADR [0x8C] STATUS CRC16 DEVICE: The DEVICE identifies the target controller inside the reader. The following devices are acceptable: DEVICE AC-Controller Value FEIG ELECTRONIC GmbH Seite 7 von 9

8 BANK: The BANK addresses a specified memory bank of the target device. The following banks are acceptable: BANK Value Note Main 0x01 For RF-independent settings MODE: The MODE controles the command. The following flags are defined: LOC LOC: specifies the location of the configuration block b000 RAM b001 RAM and EEPROM ALL: specifies to reset the complete configuration from RAM or EEPROM b0 configuration to be reset specified by CFG-ADR and CFG-N b1 reset complete configuration. CFG-ADR and CFG-N ignored CFG-ADR: First block address of the required configuration blocks. CFG-N: Number of configuration blocks to be reset. FEIG ELECTRONIC GmbH Seite 8 von 9

9 STATUS: Hex-value General 0x00 OK: Data / parameters have been read or stored without error Control command has been executed Write Error Write of configuration block failed internally 0x11 Parameter-Range-Error: The range of values for one or more parameters were exceeded 0x16 Write Protect This status is returned only if one configuration block (CFG-N = 1) is to be reset and the configuration block at this block address is reserved for future use FEIG ELECTRONIC GmbH Seite 9 von 9