Network Set-up and Operation

Transcription

1 Owner s Manual Network Set-up and Operation Wired Setting Projector Set-up and Operation This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed strictly. for HDT700

2 Compliance Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 2

3 Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. If you remotely use the projector via networks, carry out a safety check regularly and take particular care to its environment. Incorrect installation may cause fire or other accidents. CAUTION IN USING NETWORK FUNCTION We assume no responsibility for the loss or damage of data, or damage of the computer caused by using this projector. Making back-up copies of valuable data in your computer is recommended. ENGLISH 3

4 Table of contents Compliance...2 Safety instructions...3 Table of contents...4 Chapter 1 Preparation...5 Features...6 Required operating environment for computers...7 Network specifications of the projector...7 Flow of installation...9 Notice about installing Software CD-ROM...9 Chapter 2 Setup Procedures Connecting to the LAN line Network configuration Network PIN code Network information AMX D. D Network factory default Wired LAN factory default settings Chapter 3 Basic Setting and Operation Login the setting page of the projector [1] Enter the IP address...18 [2] Login...18 [3] Display of main setting page...19 How to use the setting page...20 Initial setting...22 Network PIN code setting...23 PJLink and password setting...23 Network configuration setting...26 Examples: Type and contents of alert mail...29 SNMP setting...30 Chapter 4 Controlling the Projector Power control and status check...34 Control...36 Input...36 System...37 Image adjustment...38 PC adjustment...39 Setting up the projector...40 Screen setting...40 Lens adjustment...41 Setting Setting Setting Information...44 Chapter 5 Appendix Examples of connection...48 Use of telnet...50 Web browser setting...52 Examples: OS/Browsers...53 Q&A

5 Chapter 1 Preparation 1 Describes features and operating environment of this projector. ENGLISH 5

6 Chapter 1 Preparation Features Web Management function (+p.33) With this function, you can monitor projector functions such as power status, lamp status, input mode, signal condition, lamp-use time, etc. through the network by using the web browser installed on your computer. PC1 PC3 PC2 PC4 PC5 PJ2 Turn ON PJ2 PC6 PJ1 Alert function (+p.26) The projector sends messages to the registered addresses when a lamp abnormality or power failure occurs with the projector. This message describes how to solve the cause of the problems. You can take efficient action for quick recovery. PC1 PC3 PC2 PC4 PC5 PJ2 You ve got Mail. PC6 PJ1 SNMP Agent function (+p.30) To send the information of the projector to the SNMP manager. Enables you to manage the projector condition with the supplied SNMP manager software. SNMP Manager function A function to manage the condition of projectors in the network by using the SNMP protocol. The managing computer needs to provide an SNMP managing software. Refer to the owner's manual of the "PJ Network Manager" supplied separately for further details. PJ1 PC6 PJ2 PJ3 PJ4 Trap Trap PC5 SNMP Manager You received a Trap. PC4 6

7 Required operating environment for computers Features When operating the projector via networks, computers should meet the operating environment below. Operating System Computer environment Recommended CPU Memory Free disk space Drive equipment Display settings Network card Web Browser* Recommended Internet Mailer* Windows 2000, Windows XP (32bit version), Windows Vista (32bit version), Windows 7 (32bit version) Mac OS X v 10.4 or 10.5 Windows: Pentium III 900MHz or more Macintosh : 800 MHz PowerPC G4 or faster,or 1.8 GHz Intel Core Processor or faster Windows : 64MB (Minimum)/ 128MB or more (Recommended) 128MB or more for Windows XP 1GB or more for Windows Vista or Windows 7 Macintosh : 256MB or more (512MB is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x 768) Number of colors: Either of 16 bit (65,536 color 24/32 bit (16.77 million colors)) The computer must provide a 10Base-T or 100Base-TX network card. Internet Explorer version 6.0, 7.0 or 8.0 Netscape Navigator version 7.1 or 9.0 Safari 3.1 * Used to control and set up the projector. The layout of pages in the browser may slightly differ from each type of application or operating system you use. - Microsoft Outlook - Microsoft Outlook Express - Netscape Mail * Required the internet application software to receive an alert sent from this projector. If you do not use the function Alert, this application is not required. Network specifications of the projector LAN Terminal Data communication standards 10Base-T/100Base-TX/1000Base-T compatible Physical layer Protocol 10Base-T TCP/IP ENGLISH 7

8 Chapter 1 Preparation Cabling Between the Projector and a Hub or computer *1 Use an appropriate cable when connecting the projector and a hub or computer. Connection Ethernet cable type Max. cable length Projector - Hub STP straight-through category 5 * 2 cable 100m (328feet) Projector - Computer STP crossover category 5* 2 cable 100m (328feet) *1 There may be other limitations depending on your network environment or LAN specification. Please consult your network administrator for further details. *2 Cable category indicates cable quality. Notice Expression/Abbreviation The OS of the computer and the Web browser described in this manual are Windows XP Professional and Internet Explorer 6.0. In case of another OS or Web browser, some instruction procedures may differ from the actual operation depending on your computer environment. Use of this manual This manual does not provide the detailed description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer to the respective manual. Trademarks Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows, Windows 2000, Windows XP, Windows Vista and Windows 7 are registered trademarks of Microsoft Corporation in the United States and other countries. Internet Explorer is a registered trademark of Microsoft Corporation. Netscape Navigator and Netscape Communicator are trademarks or registered trademarks of Netscape Communications Corporation. JavaScript is a registered trademark of Sun Microsystems, Inc. Macintosh is a registered trademark of Apple, Inc. in the USA and other countries. PowerPC is a registered trademark of IBM Corporation. Intel Core is a registered trademark of Intel Corporation in the USA and other countries. Other product or brand names in this manual are registered trademarks or trademarks of their respective owners. * Unauthorized use of a part or whole of the contents in this manual is prohibited. * The contents of this manual are subject to change without notice. 8

9 Flow of installation To use the projector via the networks, follow the setup procedures below. Flow of installation STEP 1 Connect the LAN and set the configuration. Decide depending on the LAN environment. 2. Setup Procedures (pp.11 16). Detailed LAN configurations need to be done with a browser later. First, complete the Wired LAN connection between computers and projectors, then start browser configurations. 3. Basic setting and operation (pp.17 31). STEP 2 Network Configuration has completed. Follow each chapter to operate the projector. Operate and manage the projector 4. Controlling the projector (pp.33-45) Power Control and status check (p.34) Control (p.36) PC adjustment (p.39) Setting up the projector (p.40) Information (p.44) STEP 3 Install the Software on computers. Install the software recorded in CD-ROM on each computer which will be operated. Refer to the owner's manual of PJ Network Manager. Notice about installing Software CD-ROM It is available for controlling and setting of the projector by using the web browser without installing any software. So it is not required to install the software into your computer. For PJ Network Manager function, it is required to install the software. Please see the owner's manual of "PJ Network Manager Function". ENGLISH 9

10 10 Chapter 1 Preparation

11 Describes how to configure the network. 2 Chapter 2 Setup Procedures ENGLISH 11

12 Chapter 2 Setup Procedures Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately. Connecting to the LAN line Connect the LAN cable to the LAN connection terminal of the projector. LAN Connection Terminal LINK Lamp (Green) Light green when the projector is connected to the network correctly. ACT Lamp (Orange) Blink orange when the projector is sending or receiving the data. Network configuration Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to 3. Basic setting and operation (p.17-31). First, complete the settings described in this chapter before performing steps in 3. Basic setting and operation. Setting Procedure LAN Cable * Please use a shielded LAN cable. 1. Select Network in the Network menu, and press Point 8 or SELECT button. 2. Select "On" with the Point ed buttons, and the press SELECT button. Then the Menu will disappear, the Please wait... message will appear, and switching operation will start. Switching will take a while and the projector s LINK/ACT Lamp will be on or blink, and after completing the operation, the Please wait... message will disappear. 12

13 Network configuration 3. Select "Network setting" in the Network menu and press SELECT button, and then the LAN setting screen will appear and selected LAN settings will be displayed. Adjust each item to the setting environment. Consult your system administrator about the detailed settings. Press SELECT button in a row where you want to adjust, and adjust the figures with the Point ed buttons and move among the items with the Point 7 8 buttons, and then press SELECT button to fix. Move to the next row with the Point ed buttons to adjust. 4. After completing all the settings, select Set and press SELECT button. Now, all procedures have been done. To cancel the adjusted settings, select "Cancel" and press SELECT button. You can confirm the LAN settings you have made from Network information (p.14). In such cases that the LAN cannot be connected, see this screen. Network setting DHCP: On DHCP: Off * The numerical value is a setting example. Item Description DHCP... Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, Gateway and DNS are automatically set according to your network environment * 1. IP address...sets IP address of the projector Subnet...Sets Subnet mask. Normally sets Gateway* 2...Sets IP address of the default gateway (Router) DNS* 3... Sets IP address of the DNS server. *1 Set "On" only when the DHCP server is available on your network environment. *2 Set [ ] if the network does not provide the gateway (router). *3 Set [ ] if you do not use the function alert. ENGLISH 13

14 Chapter 2 Setup Procedures Network PIN code The Network PIN code is to restrict the access to the projector through the network. After setting the Network PIN code, you need to enter it to operate the projector via the networks. 1. Select "Network PIN code" in the Network menu, and press SELECT button. The Network PIN code screen will appear. 2. Set the Network PIN code. Set the figures with the Point ed buttons and move to the next items with the Point 7 8 buttons. Select Set and press SELECT button to set. To cancel the preset Network PIN code, select Cancel. When you do not want to set the Network PIN code, set "0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. See 3. Basic setting and operation Initial setting Network PIN code setting (p.23). Network PIN code Network PIN code screen Network information Select "Network information" in the Network menu and press Point 8 or SELECT button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what will be shown.) 14 * The numerical value is a setting example.

15 AMX D. D. Network factory default Choose AMX D. D. in the Network menu and press SELECT button, select ON or OFF to allow the projector to be detected by AMX Device Discovery. For more details, visit Network factory default 1. Select Network factory default in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" and then press SELECT button. 3. Another confirmation box appears and select "Yes" and then press SELECT button. 4. All the wired LAN settings will go back to the factory default settings. For details, refer to Wired LAN factory default settings as shown in the table below. ENGLISH 15

16 Chapter 2 Setup Procedures Wired LAN factory default settings Parameter DHCP Settings Off IP ADDRESS SUBNET MASK GATEWAY ADDRESS DNS ADDRESS

17 3 Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. ENGLISH 17

18 Chapter 3 Basic Setting and Operation Login the setting page of the projector [1] Enter the IP address Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and then press "Enter" key. Enter the address that you configured in item "Network configuration" (+ p.12). * The numerical value is a setting example. [2] Login If the setting page has set the password, the authentication window will appear. In this case type "user" onto the User Name text area and the login Network PIN code onto the Password text area and then click OK (Log in) button. * The entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the auto-login will be performed and the next main setting page is displayed. 18

19 Login the setting page of the projector [3] Display of main setting page The following main setting page will be displayed according to your display mode selection. Perform various kinds of settings through this page. Click on the menus to display the control and setting pages. Main setting page in the display Sub menu tab Switches the sub menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. ENGLISH 19

20 Chapter 3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab. * Each item has a valid setting range respectively. Types of setting Text box setting Enter a number or text and then click Set button. or Change a value with or + button. Pull-down menu setting Select an item with pull-down menu button and then click Set button. 20 The value in the text box indicates current value. Each item has a valid setting range. The setting value exceeding this becomes invalid. Some control items can not be used depending on the selecting input mode or functions of the projector you use. In this case, the values of those items are indicated with "---".

21 How to use the setting page Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. ENGLISH 21

22 Chapter 3 Basic Setting and Operation Initial setting After installing the projector, perform the following basic initial setting. Click Initial Setting on the main menu to display the initial setting page. * The serial number in the figure is used for an example. Item Description Language... Switches display language on the setting page. (Japanese, English) Model name... Indicates the model name of the projector SERIAL NO....Indicates the serial number of the projector Network PIN code... Sets the Network PIN code to login the setting page (+p.23) Temperature... Switches display temperature unit. (Centigrade, Fahrenheit) PJLink... Switches PJLink password authentication. (ON, OFF) (+p.23) Password... Password for PJLink function (+p.23) 22

23 Initial setting Network PIN code setting This is to set the Network PIN code to restrict the access from an unauthorized person through the network. Enter a 4-digit number as the Network PIN code onto the text box and click Set button. The projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. This is to perform the login authentication firmly. The default Network PIN code [0000] means no Network PIN code is set. When you connect the projector to the network, it is recommended to set a new Network PIN code. Only a four-digit number is valid for the Network PIN code. PJLink and password setting This is to set the PJLink password authentication on or off. If set "ON" with the PJLink pulldown menu, the password must be required. Enter a password* onto the text box and click Set button. 1 to 32 alphanumeric characters can be used for the password. What's PJLink? The projectors equipped with PJLink function can be used together on the same network, regardless of model or brand, for centralized control and monitoring. This standard was established by the Japan Business Machine and Information System Industries Association (JBMIA). Please visit the Website at PJLink Notice The projector is compliant with PJLink Standard Class 1 of JBMIA, and it supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. Projector Input PJLink Input Parameter Input 1 RGB (PC analog) RGB 1 11 RGB (Scart) RGB 2 12 RGB (PC digital) DIGITAL 1 31 RGB (AV HDCP) DIGITAL 2 32 HDMI DIGITAL 3 33 Input 2 Video VIDEO 1 21 Y, Pb/Cb, Pr/Cr VIDEO 2 22 RGB RGB 3 13 Input 3 Video VIDEO 3 23 Y, Pb/Cb, Pr/Cr VIDEO 4 24 S-video VIDEO 5 25 Input 4 NETWORK NETWORK 1 51 ENGLISH 23

24 Chapter 3 Basic Setting and Operation Network configuration Click Network on the main menu. The following setting page is displayed. The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) and projector name are set up on this menu. The IP address and Subnet Mask have been configured already in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. * The numerical value is a setting example. Item Description DHCP... Sets DHCP configuration (ON/OFF). IP address... Sets IP address of the projector Subnet mask... Sets Subnet mask. Normally sets Default gateway* 1... Sets IP address of the default gateway (Router) DNS* 2... Sets IP address of the DNS server. Must be set when using the function Projector name* 3... Sets name of the projector. (64 characters maximum) You must use the number specified by your administrator. The address must be entered as a group with four numbers split by a dot like [ ]. 24 *1 Set [ ] if the network does not provide the gateway (router). *2 Set [ ] if you do not use the function alert. *3 If you use the DNS server, register the host name registered to the DNS server as a projector name. You can access with this projector name from any computers in your network. If you do not use the DNS server, access with the assigned IP address to the projector. * All the network setting will reset to the default when setting [ ] of the IP Address. * If you make incorrect settings, you cannot find out the new network settings. Be careful to set up them correctly, otherwise you cannot connect to the projector. It is recommended to make a note of them.

25 Network configuration Item Crestron control You can use Crestron RoomView to monitor and control the projector through the network. For more information, visit crestron.com & Description IP address... Control System IP Address as a string. The default value is blank. IP ID... Control System IP ID as a string. The default value is blank. (from 3 to 254) Port... The default value is (from 1 to 65535) AMX D. D. If your network environment uses an AMX controller, select ON to allow the projector to be detected by AMX Device Discovery. (ON, OFF) For more details, visit ENGLISH 25

26 Chapter 3 Basic Setting and Operation setting This projector has an function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click Setting on the main menu and follow the below steps. Item Description SMTP server... Enter server name or IP address of the SMTP server. (up to 60 characters) SMTP server port... Enter Port number of the SMTP server. (from 1 to 65535) Administrator address...enter address of administrator. Add address... Enter address of the user to send mail when the projector has an abnormality. SMTP Authentication setting Auth... Sets authentication setting option. (OFF, SMTP Auth, POP before SMTP) SMTP Auth... Sets user authentication setting option when selecting "SMTP Auth" in above column. (CRAM-MD5, LOGIN, PLAIN) User ID... Enter SMTP user ID. (up to 63 characters) Password... Enter SMTP password. (up to 63 characters) POP server... Enter server name or IP address of the POP server. (up to 60 characters) POP server port... Enter Port number of the POP server. (from 1 to 65535) 26

27 setting 1 Setting SMTP server and administrator address Enter the server name or IP address of the SMTP server* 1, the port number of the SMTP server and administrator address and click Set button. The administrator address is set to "Reply-To" address of the message sent from the projector. *1 The SMTP server is a server for sending . Please contact your network administrator to have this SMTP server address. 2 Registering and deleting addresses Enter the address onto "Add address" and click Set button. To check the registered addresses, click Check/Delete sub menu tab. The addresses are listed as the figure on the right. Check / Delete Up to 10 addresses can be registered. To delete the registered addresses, check the address you want to delete and click Delete button. 3 Setting SMTP authentication Set the SMTP authentication concerned and click Set button. Please contact your network administrator in details. If the projector sends an alert message due to the abnormality on the projector but the SMTP server is down in some other reason, the message will not be sent. In this case, the message "Unable to connect to server." will be displayed on the setting page. To clear this message, set up SMTP server address again. To use the function, it must be set the DNS address on the Network setting page correctly. You cannot use this function if the DNS server and SMTP server cannot be used in your network environment. The projector does not send message to the address set in "Administrator address" text box. If you want to send s to the administrator address, enter the administrator address into "Add address" text box. ENGLISH 27

28 Chapter 3 Basic Setting and Operation 4 Setting POP server When "POP before SMTP" is selected at "Auth" of "SMTP Authentication setting", enter "POP server* 2 " and "POP server port" and click Set button. *2 The POP server is a server for receiving . Please contact your network administrator to have this POP server address. Error message for sending alert mail When the projector has an abnormality, an alert message will be sent to the registered address. If the SMTP server is missing or the authentication is not completed because of input error in address setting or SMTP authentication setting when sending alert , the error message will be displayed. Please check the respective settings. Error message for missing SMTP server Error information Error message for authentication problem Error information 5 Option selection for sending alert mail Click Option sub menu tab. Check the condition items under which alert mail will be sent and click Set button. Option Please refer to item "Examples :Type and contents of alert mail" described on the next page. 28 "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the side control or the remote control. Up to 99,999 hours can be set for use time.

29 setting Examples: Type and contents of alert mail When the projector has an abnormality, the following alert messages are sent to the registered address according to your selected condition. Administrator or user can take an efficient action quickly by receiving this message. This is very useful to maintain and service the projector. The following are examples of received messages. When internal PJ temperature is too high: TITLE: Message from projector Projector Model Name: model name TCP/IP: Projector Name: Proj05 It sends you following message. * The projector lamp is turned off because internal temperature goes over the safety limit. Wait for the completion of the cooling process and make sure the projector has been turned into Standby. Then turn the projector on again. If the Indicator continues flashing, check the air filter for dust accumulation. When PJ needs service: TITLE: Message from projector Projector Model Name: model name TCP/IP: Projector Name: Proj05 It sends you following message. * Maintenance requirement from Projector is detected. Check up LED status of projector and consult with the dealer. AD, 3.3V OK KS, 3.3V OK Error information MAIN, 3.3V NG The projector lamp was turned off, because the projector power circuit failed. Unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the error information. When PJ lamp replacement time is reached: TITLE: Message from projector Projector Model Name: model name TCP/IP: Projector Name: Proj05 It sends you following message. * The projector lamp has reached replacement time. Lamp ON 2000 h Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every poweron of the projector. This alert mail will not be sent when unchecking the mail sending condition "When PJ lamp replacement time is reached". ENGLISH 29

30 Chapter 3 Basic Setting and Operation SNMP setting This projector provides a SNMP (Simple Network Management Protocol) agent function. The SNMP consists of a manager and agents. The group which communicates information each other with SNMP is called "Community". There are two access modes in a community, Refer (read only) and Set (readwrite). This projector allows to use Refer (read only) only. The SNMP message informs the projector status called "Trap" to an administrator. Click SNMP Setting on the main menu and set up each item. PJ information Item Description Contact... Enter user name of the projector etc. (optional) Place...Enter place of the projector (optional) Community name(refer)... Enter community name (read only). Default name is "public". Item Trap Description Community name... Enter community name to send "Trap". Default name is "public". Trap address... Enter IP address of the SNMP manager computer to receive "Trap". 30

31 SNMP setting Trap check/delete Check and delete the trap address Checking the registered trap address and deleting the address. To delete the address, tick check box in front of the IP address and click Delete button. Up to 10 trap addresses can be registered. Trap option Trap option setting Tick check boxes in front of the condition item to send the trap. Click Set button if you tick or un-tick the check box on a page. "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the side control or the remote control. Up to 99,999 hours can be set for the time setting. ENGLISH 31

32 32 Chapter 3 Basic Setting and Operation

33 4 Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. ENGLISH 33

34 Chapter 4 Controlling the Projector Power control and status check Click Power & Status on the main menu. The control page will be displayed. By clicking ON or Standby button on the page, the power of the projector can be controlled. Confirmation window as shown in the below appears when the Standby button is pressed. Warning temperature icon Popup confirmation window 34 Item Description PJ status Power... Displays the status of the lamp. (ON, OFF, On starting up, On cooling down, Service in need) Status... Displays the status of the projector's power. (Refer to next page.) Power control... Controls the projector power by clicking the "ON" or "Standby" button. PJ temp. External temp. A... Displays the temperature around the remote control receptor at the front of the projector. Inside temp. A... Displays the surrounding temperature of lamp in the projector. Inside temp. B... Displays the surrounding temperature of panel in the projector. * The warning icon will appear if the temperature exceeds a specified value. Check if there is no object to obstruct the airflow around the intake or exhaust vent. It might be airfilter clogged. Replace the airfilter with new one. * The temperature unit can be set either Centigrade or Fahrenheit in the item "Initial Setting". (+p.22) The projector cannot be turned on while the projector is on cooling down. The web browser checks and updates the projector's condition every 30 seconds automatically.

35 Power control and status check About projector condition Status Description Normal... Projector is operating normally. Power management in operation... Power management is operating Lamp failure... Lamp failure is occurring Abnormal temperature... The temperature of the projector became too high Standby after Abnormal Temp... Projector detects abnormal temp. and sets into standby mode. Power failure... Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel. When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control the projector through the network temporarily, execute "PJ lock suspend" command to unlock the security. "PJ lock suspend" is on setting sub menu [2] on Setting main menu. (+p.42) ENGLISH 35

36 Chapter 4 Controlling the Projector Control Click Control on the main menu. The setting method differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. Please see the owner's manual of the projector to have the further information of each control item. 36 Input This function is to select the input mode and source mode of the projector. Click Set button after selecting the input and source mode. Item Description Input... Selects input mode of the projector. Source... Selects signal source of the input. RGB : RGB (PC analog) RGB (Scart) RGB (PC digital) RGB (AV HDCP) HDMI 5BNC : Video Y, Pb/Cb, Pr/Cr RGB VIDEO : Video Y, Pb/Cb, Pr/Cr S-video The control page displays valid control items depending on the selected input mode, signal or functions of the projector you use, therefore, there may be different controls between the described items and actual control items on the page display. For further information, refer to the projector's owner's manual. When the projector is in standby, all the controlling items are inactive.

37 Control System This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button. Available selection at the RGB(PC analog) input Item Description XGA1... It automatically switches to the proper computer system of the input signal. * The computer system modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal are listed. Available selection at the RGB(PC digital), RGB(AV HDCP) or HDMI input Item Description D-XGA... It automatically switches to the proper computer system of the input signal. * The computer system modes (D-VGA, D-SVGA, D-XGA. D-SXGA1...) which meet the input signal are listed. D-480p... It automatically switches to the proper scanning system of the input signal. * The selectable scanning systems are D-480p, D-575p, D-720p, D-1035i, D-1080i and D-1080p. Available selection at the Video/S-video/Scart input Item Description AUTO... It automatically switches to the proper color system of the input signal. * The selectable color systems are PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N. * AUTO is fixed at the Scart input. Available selection at the Component input Item Description AUTO... It automatically switches to the proper scanning system of the input signal. * The selectable scanning systems are 480i, 575i, 480p, 575p, 720p, 1035i, 1080i and 1080p. ENGLISH If the mode (Mode1 to Mode10) which is stored in the item "PC Adjustment" ( p.39) is available, they are also listed together with the above mode. 37

38 Chapter 4 Controlling the Projector Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button. Item Description Contrast... Adjusts picture contrast. (0~ 63) Brightness... Adjusts picture brightness. (0~ 63) Color... Adjusts picture color saturation. (0~ 63) Tint... Adjusts picture hue. (0~ 63) Color temp... Sets a color temperature mode. (X Low, Low, Mid, High, Adj.) White balance Red, Green, Blue... Adjusts each white balance respectively. (0~ 63) * When changing the value of the white balance, the color temp. indicates "Adj." Offset Red, Green, Blue... Adjusts each offset respectively. (0~ 63) Auto picture control... Sets auto picture control level. (OFF, L1, L2) Advanced color... Applies improved color adjustment with yellow light controller. (Auto, OFF) Sharpness... Adjusts picture sharpness. (0~ 31) Gamma... Adjusts brightness of darker part of the picture. (0~ 15) Noise reduction... Switches noise reduction mode (ON, OFF) Progressive...Switches progressive mode (OFF, ON, Film) Reset... Resets the Image adjustment to previous levels. Store... Stores the Image adjustment values. Select an item [Image1 - Image10] from the pull-down menu and click Store button. Load image mode... Loads the Image mode. Select an image mode from the pull-down menu and click Load button. There may not be available mode depending on the input mode as shown in the table left. 38 Input source Image mode Video Computer Dynamic 4 4 Standard 4 4 Natural 4 * Cinema 4 * Real * 4 Image The mark "4" means that the available image mode in the selected input source. The error message appears when selecting the disabled image mode indicated with "*".

39 PC adjustment PC adjustment Click PC Adj. on the main menu. This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode... Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or Mode1 - Mode10 which are the customized mode created by using the "Mode Store" function described below. Auto PC adj... Performs automatic adjustment. Fine sync... Performs Fine Sync adjustment. (0 ~ 31) Total dots... Adjust the number of total dots in the horizontal period. Clamp...Adjusts the phase of the clamp. Display area Horizontal...Adjusts the image area horizontally. Vertical...Adjusts the image area vertically. Position Horizontal... Adjusts the horizontal position of the screen. Vertical...Adjusts the vertical position of the screen. Reset... Resets the PC adjustments to the previous levels. Mode Store... Stores the PC adjustment values. Select a mode no. [Mode1 - Mode10] from the pull-down menu. Mode Free... Clear the PC adjustment values. Select a mode no. [Mode1 - Mode10] from the pulldown menu. ENGLISH 39

40 Chapter 4 Controlling the Projector Setting up the projector Click Setting on the main menu. This function is to set up the projector. Select the sub menu [Screen setting] or [Setting] and then set up each setting. Screen setting This function is to adjust the screen mode or the lens functions of the projector. Item Description Screen... Switches the screen mode. (Normal, Full, Wide(16:9), Zoom, True, Natural wide, Custom) Ceiling... Sets the image top/bottom and left/ right reversed. (ON, OFF) Rear... Sets the image left/right reversed. (ON, OFF) * See the next page for the description of other functions. 40

41 Setting up the projector Item Description Screen aspect... Sets the aspect. {Default(16:9), 16:10, 4:3} Keystone... Corrects the keystone distortion of the projected image on the screen by pressing the Up/Down/Left/Right buttons. Click Reset to reset the keystone correction. Digital zoom... Adjusts the image zoom in and out at computer input mode. Click OFF to return the image to its normal size. Reset... Resets the settings of Screen, Ceiling, Rear, Keystone and Digital zoom. Screen Aspect Default(16:9) 16:10 4:3 Input source Input source Input source Screen mode Video PC Video PC Video PC Normal Full Wide(16:9) *1 * Zoom True *1 4 *1 4 *1 4 Natural wide *2 *1 *2 *1 *1 *1 Custom The mark "4" means that the available screen mode in the selected input source system. *1 The error message appears when selecting the disabled screen mode indicated with "*1". *2 Natural wide cannot be selected when 720p, 1035i, 1080i or 1080p is selected in AV system menu. Lens adjustment Item Description Zoom... Adjusts the image zoom in and out. Focus... Adjusts the focus of the image. Lens shift... Positions to the desired point by pressing the Up/Down/Left/Right buttons. Click Reset to return to the center position. * Step(s)... Sets the effective steps (1-20 steps) by one pressing the +/- or Up/Down/Left/Right buttons to adjust them quickly. ENGLISH 41

42 Chapter 4 Controlling the Projector Setting 1 Item Description Input button... Sets the input search mode by pressing the INPUT button of the projector and the remote control. (Mode1, Mode2, Mode3) Display... Switches on or off the on-screen menu display on the screen. (ON, Countdown off, OFF) Countdown off... Displays input image instead the countdown during the startup. Background... Sets the screen background when no signal input. (Blue, User, Black) Logo... Sets on or off the logo display on the screen during the startup. (User, Default, OFF) Picture in Picture... Sets the Picture in Picture mode. (OFF, User1 - User5) Edge blending... Sets the seamless overlapping for multi-screen. (ON, OFF) Color matching...corrects the difference of color for multi-screen. (ON, OFF) HDMI setup... Sets the input signal from HDMI input. Image... Sets the Digital RGB image level of HDMI. (Normal, Enhanced) Lamp control... Selects lamp control mode. (Auto, Normal, Eco1, Eco2) Setting 2 Item Description Filter control... Scroll the filter. Click "Roll-up", a confirmation display appears, and then click "OK", the filter will be scrolled. Fan speed control... Sets the running speed for the cooling fans. (Normal, Max) Remote control... Selects the remote control code. (Code1 - Code8) Power management... Sets into the selected power management mode (OFF, Ready 1, Ready 2, Shut down) if the input signal is interrupted and no control key is pressed for the specified period of time. * The specified time can be set 1 to 30 min. Direct on... Sets the power-on mode when the AC cord is connected to the outlet. Key lock... Sets the prohibition of controls either Projector or Remote control. (OFF, Projector, Remote control) PJ lock suspend... When the projector has a security of PIN code lock, disable this function temporarily by pressing Execute button. Setting procedure 1. Turn off the projector, disconnect AC cord from the outlet and then connect AC cord again. 2. Access this page with the web browser. 3. Click Execute button on the PJ lock suspend. * See the next page for the description of other functions. 42

43 Setting up the projector Continue from the previous page. Item Description Shutter... Sets the shutter operation. (ON: close, OFF: open) Shutter management... Sets the shutter management operation. Release key... Sets available keys to release the shutter. (Any, SHUTTER) Time... Sets the specified period of time when the projector shuts down after the projector is left with the shutter closed. * The specified time can be set 5 to 480 min. Setting 3 Item Description Closed caption.. Sets the closed caption function. Closed caption... Sets the closed caption mode. (OFF, CC1, CC2, CC3, CC4) Color... Sets the color of the contents. (Color, White) Lamp Corres. Value(h)... Displays the lamp use time (Corresponding value). Reset the time after lamp replacement. Click "Reset", a confirmation display appears, and then click "OK", the time will be reset. Filter counter(h)... Displays the filter counter. Reset the time after filter cartridge replacement. Click "Reset", a confirmation display appears, and then click "OK", the time will be reset. * Do not reset the Filter counter when the filter cartridge is not replaced. Filter warning... Sets the time to indicate the filter warning message on the screen. (OFF, 400H, 700H, 1000H) Scrolls remaining... Displays the scrolls remaining of the filter. Reset the scroll counter after filter cartridge replacement. Click "Reset", a confirmation display appears, and then click "OK", the time will be reset. * Do not reset the Scrolls remaining when the filter cartridge is not replaced. Freeze... Sets the image to freeze mode. (ON, OFF) Test pattern... Sets the preset image of the projector. (OFF, Color, Gradation1 - Gradation4, All white, All black, Cross) Factory default... Sets all of the projector control items to the factory default setting except the following items. User Logo, Logo PIN code lock, PIN code lock, Lamp Corres. Value, Filter counter, PJ time, Network PIN code, Network setting * This function is not effective for the settings of Network address settings, settings, etc. ENGLISH 43

44 Chapter 4 Controlling the Projector Information This page is to display the basic information of the projector status. Click Information on the main menu. Click this button to update the information. Information Items Description Input... Displays selected input and source. System...Displays selected signal system. Signal...Input signal status (Yes, No) Screen...Displays screen mode. Lamp status... Displays lamp status with an icon. Refer to the table as shown in the next page. Security...Displays the security (Key lock and PIN code lock) status. Shutter... Displays the shutter status. (OFF: open, ON: close) PJ time(h)... Displays the accumulated use time of the projector. Lamp Corres. Value(h)... Displays the use time (Corresponding value) of the lamp. Filter time(h)... Displays the accumulated use time of the filter. Filter condition... Displays filter status with an icon. Refer to the table as shown in the next page. * When PIP mode is active, displays Input, System, and Screen to "PIP mode". 44 Network Items MAC address IP address Description Displays MAC address of the projector. Displays the IP address of the projector.

45 Information Indication of the lamp status Icon display/background Status White/Blue White/Red Gray/Blue Gray/Red Red/Blue with X Red/Red with X Lamp on (Normal) Lamp on (Lamp is being used over a specified use time, replace lamp immediately) Lamp off (Normal) Lamp off (Lamp is being used over a specified use time, replace lamp immediately) Lamp failure (Lamp failure, check lamp condition) Lamp failure (Lamp failure and lamp is being used over a specified use time, replace lamp immediately) Indication of the filter status Icon display/background Status Blue Yellow/Gray Red/Gray Good condition. Filter is almost clogged. Filter is clogged. Replace a filter with new one. * When the projector cannot decode the return from the filter cartridge, this icon also appears. ENGLISH 45

46 46 Chapter 4 Controlling the Projector

47 5 Chapter 5 Appendix Connection examples Use of telnet Web browser setting Q & A ENGLISH 47

48 Chapter 5 Appendix Examples of connection Peer-To-Peer connection Connecting the projector (PJ01) to the control computer (PC05) directly. * UTP cross cable Computer Name: PC05 IP Address : Subnet Mask : Default Gateway : DNS : Projector Name: PJ01 IP Address : Subnet Mask : Default Gateway : DNS : Connecting the projector (PJ01) to the control computer (PC05) via the hub. Hub To another network Computer Name: PC05 IP Address : Subnet Mask : Default Gateway : DNS : Projector Name: PJ01 IP Address : Subnet Mask : Default Gateway : DNS : Computer Name: PC10 IP Address : Subnet Mask : Default Gateway : DNS : 48 When the projector is connected to the computer directly without hub, the UTP cross cable should be used.

49 The gateway (Router) installed in the network Connecting the projector (PJ01) to the control computer (PC05) via the gateway. Examples of connection Entrance hall Computer Name : PC205 IP Address : Subnet Mask : Default Gateway : DNS : Projector Name: PJ01 IP Address : Subnet Mask : Default Gateway : DNS : Hub Network Group: x Gateway (Router) IP Address : To another network IP Address : IP Address : Office Hub Hub Computer Name: PC05 IP Address : Subnet Mask : Default Gateway : DNS : Computer Name : PC10 IP Address : Subnet Mask : Default Gateway : DNS : Computer Name : PC51 IP Address : Subnet Mask : Default Gateway : DNS : Computer Name : PC61 IP Address : Subnet Mask : Default Gateway : DNS : ENGLISH Network Group: x 49

50 Chapter 5 Appendix Use of telnet You can control the projector by using the telnet application *1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP Professional.) 1. Select Run... submenu from Start menu on the computer. Type "telnet" onto the Open text area on the displayed window and press OK button. (For example, in case of using the telnet application of Mac OS X v 10.4) 1. Select Terminal from Applications -->Utilities. Type as below on the displayed window. > telnet [return] 2. The telnet application will start and the following window will be displayed. Type as below to connect the projector. > open [return] * Use the IP address assigned to the projector. 50

51 Use of telnet 3. When communication is established correctly, the word "PASSWORD:" appears on the window. Type the login password (Network PIN code *2 ) for the projector and then press "Enter" key on the keyboard. If you do not set up the Network PIN code, just press "Enter" key. When the word "Hello" is replied, login has been succeeded. * The password "1234" is used for the example. 4. Type the commands, refer to below table, to control the projector and then press "Enter" key for termination. For example, type "C00" which is a command to turn on the projector, and press "Enter" key. Confirm the projector is turning on. * Enter with ASCII 64-byte capital characters and one-byte characters. To disconnect the communication, press "Ctrl" key and "]" key at the same time, type "close" and then press "Enter" key on the Keyboard. > close [return] The table below shows the typical command lists for controlling this projector and please consult your local dealer for further information of another commands. Command list table Command C00 C02 C1C C1D Function Power on Power off Menu display on Menu display off *1 Further instructions about the telnet application, please see the on-line guide on your computer. *2 The password is a Network PIN code decided item "Network PIN code setting" ( pp.14, 23). If the authentication of the entered password is failed 4 times continuously, the communication will be disconnected automatically. Please try again for the connection. If the password or any command is not entered for more than 30 seconds, the communication will be disconnected automatically. Please try again for the connection. ENGLISH 51

52 Chapter 5 Appendix Web browser setting This projector is designed to be set up and controlled from an Internet web browser. Depending on the preference settings of the web browser, some control functions may not be available. Please make sure that the following functions are set up properly in the web browser. Active Script/JavaScript enable There are some control items used with the JavaScript function in the setting pages. If the web browser is set not to use this JavaScript function, it may not control the projector properly. In this case, the warning message "Make sure JavaScript is ON." will be displayed on the top of the page. To enable the JavaScript, please see further instructions on the next page. Proxy setting In some cases, your web browser is set up to use the proxy server for the internet or intranet connection. In this case, when you install this projector into the local network, you should set up the proxy setting of web browser preference correctly. Especially when connecting the projector and computer with a UTP cross cable directly, or when the network does not provide the proxy server, make sure that "not use proxy server" is set up in your web browser preference. Please see item "Examples: OS/Browsers" in the next page for further setting up procedure. 52 There are various ways to change your browser preferences depending on the version or applications. Please see the setting instructions on next page for example and also refer to on-line help of your web browser.

53 Examples: OS/Browsers Web browser setting Windows XP Professional Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level button. On the security setting window, scroll down and find the Scripting item, make sure that "Enable" is selected in item Active Scripting. ENGLISH 53

54 Chapter 5 Appendix Proxy setting Select Internet Options from Tools menu on the web browser and then select Connection tab and click LAN Settings button. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected. - Using proxy server To use an external internet connection from the local area network, check the item Use a proxy server and enter the proxy server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, this must be unchecked. To designate proxy settings that will not use the proxy server when accessing the projector installed in the local area network, enter the IP address or domain name here. 54

55 Web browser setting Netscape Navigator v.7.1 JavaScript Setting Select Preference from Edit menu on the web browser and then select the item Advanced/Scripts & Plugins in the Category column. Make sure that the Enable JavaScript for Navigator is checked. Proxy setting Select Preference from Edit menu on the web browser and then select the item Advanced/ Proxies in the Category column. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your network administrator. - Not using proxy server Select the item Direct connection to the Internet in the proxy setting window. If you connect the projector to the computer directly with UTP cross cable, this must be selected. To designate proxy settings that will not use the proxy server when accessing the projector installed in the local area network, enter the IP address or domain name here. ENGLISH 55

56 Chapter 5 Appendix MAC OS X v 10.4 Safari v JavaScript enable setting Select Preferences... from Safari on the web browser and then select Security tab and check E n a b l e JavaScript. Proxy setting 1 Open Preferences... from Safari menu on the web browser Safari. The preference menu appears. 2 Select Advanced icon and then click Proxies: Change Settings... 3 Select Proxies tab and properly set up your web browser Safari's the proxy server settings according to the local area network environment to which the projector is connected. - Using proxy server To use an external internet connection from the local area network, check the items Web Proxy (HTTP) and Secure Web Proxy (HTTPS) of Select a proxy server to configure window and enter the proxy server address and port correctly in Web Proxy Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the items Web Proxy (HTTP) and Secure Web Proxy (HTTPS) of Select a proxy server to configure. If you connect the projector to the computer directly with UTP cross cable, they must be unchecked. 56 To designate proxy settings that will not use the proxy server when accessing the projector installed in the local area network, enter the IP address or domain name here.