Fusion EMM (Event Management Module)

Transcription

1 Fusion EMM (Event Management Module) QUICK SETUP GUIDE Fusion EMM Quick Setup Guide Rev3.1

2 Diagram 1 (Basic Setup): Diagram 2 (Advance Setup): SmartLink Fusion EMM Quick Setup Guide Rev3.1 1

3 1. Contents 1. Contents Introduction Basic Configuration using IPDiscover Logging In (EMM1 & EMM2) Messaging Setup (EMM1 & EMM2) Scope Setup (EMM1 & EMM2) POCSAG Setup (EMM2) Recipients/Contacts Setup (EMM1 & EMM2) SCU2 Setup (EMM1) SmartWire or SmartLine Setup (EMM1) SmartLink Residents Setup (EMM1) Send Message Screen Sent Items Screen Inbox Screen Active Alarms Screen Logging Out SmartLink Fusion EMM Quick Setup Guide Rev3.1

4 2. Introduction 1. Fusion EMM Kit: EMM 1 & EMM 2 1 x Green Crossover Serial Cable (RJ45 to RJ45) for SCOPE (Com1) 2 x Blue Straight Through Cable (RJ45 to RJ45) 2xRed Crossover Ethernet Cable (RJ45 to RJ45) SmartLink Fusion EMM Software Quick Setup Guide 2. Fusion EMM Unit (19 Rack Mount Version): 3. Fusion EMM Unit (Desktop Version): SmartLink Fusion EMM Quick Setup Guide Rev3.1 3

5 3. Basic Configuration using IPDiscover In order to view the user interface, you must first connect to the EMM1 and EMM2 via its Ethernet Port. There are two ways that you can connect to the units. 1. Directly with apc or Laptop using the supplied Crossover Ethernet Cable (Red RJ45 RJ45). 2. By connecting the units to a local area network (LAN) to a spare port or to a Switch/Hub,usingthe supplied Straight Through Ethernet Cable (Blue RJ45 RJ45). Once you have Connected and Power UP the units, you can use a utility called IPDiscover to locate your units on the network and start a web session with the units. This program is included in the SmartLink Fusion CD. Run the Program and you will see all Fusion EMM on the network. NOTE: DHCP is enabled by default. If no DHCP server is found on the network, the default IP of will be used. To configure the IP settings of EMM1 In the example below, there is two EMM units on the network at IP Address and Select and Click the CfgIP button to configure the IP settings of EMM1 as shown below. 4 SmartLink Fusion EMM Quick Setup Guide Rev3.1

6 You can then turn off DHCP if it is not required or change the EMM1 IP Address. Type eg Nunawading Aged Care EMM1 as the Host Name and Click the Send button to configure the IP settings of EMM1 as shown below. Click the YES button to continue as shown below. Click the OK button to continue as shown below. To configure the IP settings of EMM2 In the example below, select and Click the CfgIP button to configure the IP settings of EMM2 as shown below. SmartLink Fusion EMM Quick Setup Guide Rev3.1 5

7 You can then turn off DHCP if it is not required or change the EMM2 IP Address. Type eg Nunawading Aged Care EMM2 as the Host Name and Click the Send button to configure the IP settings of EMM2 as shown below. Click the YES button to continue as shown below. Click the OK button to continue as shown below. Click the Discover button to continue as shown below. 6 SmartLink Fusion EMM Quick Setup Guide Rev3.1

8 Wait at least 2 minutes and then Click the Discover buttonagainuntilip and Given Name has been updated as shown below. To open a Browser Window on EMM1 Click the IP and then Web button as shown below. A browser window will open shortly displaying the Login Screen. To open a Browser Window on EMM2 Click the IP and then Web button as shown below. A browser window will open shortly displaying the Login Screen. SmartLink Fusion EMM Quick Setup Guide Rev3.1 7

9 4. Logging In (EMM1 & EMM2) At the Login Screen you will be prompted to enter your details. The default login details are: User name: maint Password: To Log In EMM1 Typemaint as the User name and Click the Log In button as shown below. The Send Message Screen will then be shown below. NOTE: The EMM has many features and protocols that are enabled by license key. As a result not all features explained in the manual may be available on your EMM. For more details contact your place of purchase. 8 SmartLink Fusion EMM Quick Setup Guide Rev3.1

10 To Login EMM2 Typemaint as the User name andclickthe Log In button as shown below. The Send Message Screen will then be shown below. NOTE: The EMM has many features and protocols that are enabled by license key. As a result not all features explained in the manual may be available on your EMM. For more details contact your place of purchase. SmartLink Fusion EMM Quick Setup Guide Rev3.1 9

11 5. Messaging Setup (EMM1 & EMM2) To Setup Messaging on EMM1 Click the Settings and then Messaging as shown below. Type eg Nunawading Aged Care EMM1 as the Site Name andclick the Save Changes button when finished. To Setup Messaging on EMM2 Click the Settings and then Messaging as shown below. Type eg Nunawading Aged Care EMM2 as the Site Name andclick the Save Changes button when finished. 10 SmartLink Fusion EMM Quick Setup Guide Rev3.1

12 6. Scope Setup (EMM1 & EMM2) To Setup Scope Gateway on EMM1 and EMM2 ConnecttheCrossover Serial Cable (Green RJ45 to RJ45) from EMM1 (Com1) to EMM2 (Com1) To Setup Scope on EMM1 Click the Interfaces, Gateways and then Add New button as shown below. Type eg Output to EMM2 (Com1 Com1) as the Name Select Scope asthetype Select Yes boxastogateway enabled Select UTF 8 (default) astocharacter Set Select Com1 astheport Select No astoinput Gateway Select Yes asto Output gateway Click the Save & Close button when finished as shown below. SmartLink Fusion EMM Quick Setup Guide Rev3.1 11

13 Click the Start button as shown below. Click the Interfaces, Ports and then Edit button as shown below. Click the Save & Close button when finished as shown below. Click the X button to Exit as shown above. 12 SmartLink Fusion EMM Quick Setup Guide Rev3.1

14 To Setup Scope on EMM2 Click the Interfaces, Gateways and then Add New button as shown below. Type eg Input from EMM1 (Com1 Com1) as the Name Select Scope asthetype Select Yes asto Gateway enabled Select UTF 8 (default) astocharacter Set Select Com1 astheport Select Yes asto Input Gateway Select No astooutput gateway Click the Save Changes button when finished as shown below. SmartLink Fusion EMM Quick Setup Guide Rev3.1 13

15 Click the Start button as shown below. Click the Interfaces, Ports and then Edit button as shown below. Click the Save Changes button when finished as shown below. Click the X button to Exit as shown above. 14 SmartLink Fusion EMM Quick Setup Guide Rev3.1

16 7. POCSAG Setup (EMM2) NOTE: Skip this Section if you are NOT using a IntelPage Paging Transmitter. To Setup POCSAG Gateway on EMM2 Connect the Straight Through Cable (Blue RJ45 to RJ45) to EMM2 (TX Ouput) and Power Up the IntelPage Paging Transmitter. To Setup POCSAG Gateway on EMM2 Click the Interfaces, Gateways and then Edit button as shown below. Type eg POCSAG or IntelPage Transmitter as the Name and Click the Save & Close button when finished as shown below. SmartLink Fusion EMM Quick Setup Guide Rev3.1 15

17 Click the Interfaces, Ports and then Edit button as shown below. Select Standard Transmitter as the Preset and Click the Save & Close button when finished as shown below. 8. Recipients/Contacts Setup (EMM1 & EMM2) To Setup Contacts on EMM2 Click the Recipients, Contacts and then Add New button as shown below. 16 SmartLink Fusion EMM Quick Setup Guide Rev3.1

18 Type eg Pager 1 CC: asthename Type eg as the Address (Pager Cap Code) Click on Auto asthelocal ID Select POCSAG asthesend via Click the Save & Close button when finished as shown below. To Test POCSAG (IntelPage Transmitter) on EMM2 Select/Tick the Pager 1CC: andthenclick the Send Message to Selected button asshown below. Type eg. Testing Messages and then Click the Send button as shown below. You should receive a Text Message on the Pager. If NOT, check and make sure that the IntelPage Transmitter is Connected/Powerup or the Pager is ON. SmartLink Fusion EMM Quick Setup Guide Rev3.1 17

19 To Setup Contacts on EMM1 Click the Recipients, Contacts and then Add New button as shown below. Type eg Pager 1 CC: asthename Type eg 1 astheaddress (Pager Cap Code) Click on Auto asthelocal ID (Important! Make sure that the Local ID matches the EMM2 Contacts) Select Output to EMM2 (Com1 Com1) asthesend via Click the Save & Close button when finished as shown below. To Test Pager using SCOPE Output from EMM1 to EMM2 (Com1 to Com1) Select/Tick the Pager 1CC: andthenclick the Send Message to Selected button asshown below. 18 SmartLink Fusion EMM Quick Setup Guide Rev3.1

20 Type eg. Testing Messages and then Click the Send button as shown below. You should receive a Text Message on the Pager. If Not, check and make sure that the IntelPage Transmitter is Connected/Powerup and the Pager is turned ON. To Setup Groups on EMM1 NOTE: Skip this Section if you are NOT Setting Up Groups. Click the Recipients, Groups and then Add New button as shown below. SmartLink Fusion EMM Quick Setup Guide Rev3.1 19

21 To Setup Escalations on EMM1 NOTE: Skip this Section if you are NOT Setting Up Escalations. Click the Recipients, Escalations andthen Add New button asshown below. To Setup Users on EMM1 NOTE: Skip this Section if you are NOT Setting Up Users. Click the Recipients, Users and then Add New button as shown below. 20 SmartLink Fusion EMM Quick Setup Guide Rev3.1

22 9. SCU2 Setup (EMM1) NOTE: Skip this Section if you are NOT using a SCU2 Receiver. To Setup SCU2 Receiver Power up & Connect the SCU2 Cable to EMM1 (Com2). To Setup SCU2 on EMM1 Click the Interfaces, Gateways and then Add New button as shown below. Type eg SCU2 Receiver asthe Name Select Smartlink Alarm Module asthetype Select the Yes boxas thegateway enabled Select available Port eg. Com2 astheport Click the Save & Close button when finished as shown below. SmartLink Fusion EMM Quick Setup Guide Rev3.1 21

23 Click the Start button as shown below. Click the Interfaces, Ports and then Edit button as shown below. Select 1200 as the Baud, 8 as the Data Bits, None as the Parity, 1 as the Stop Bits, None as the Flow Control and then Click Save & Close button as shown below. 22 SmartLink Fusion EMM Quick Setup Guide Rev3.1

24 Click the View button as shown below. The Com2 s Communication Screens shown below indicates that the SCU2 is nowpolling/communicating allok. Click the X button to Exit Com2 s Communications Screen asshown above. SmartLink Fusion EMM Quick Setup Guide Rev3.1 23

25 10. SmartWire or SmartLine Setup (EMM1) Skip this Section if you are NOT using SmartWire System or SmartLine Wireless System. To Setup Power up & Connect the Cable to EMM1 (Com3). To Setup SmartWire or SmartLine System on EMM1 Click the Interfaces, Gateways andthen Add New button as shown below. Type eg SmartWire System or SmartLine System as the Name Select Smartlink Alarm Module asthetype Select the Yes box as the Gateway enabled Select available Port eg. Com3 astheport Click the Save & Close button when finished as shown below. Click the Start button as shown below. 24 SmartLink Fusion EMM Quick Setup Guide Rev3.1

26 Click the Interfaces, Ports and then Edit button as shown below. Select 9600 as the Baud, 8 as the Data Bits, None as the Parity, 1 as the Stop Bits, None as the Flow Control and then Click Save & Close button as shown below. The Com3 s Communication Screens shown below indicates that the SmartWire System is now polling/communicating all ok. Click the X button to Exit Com3 s Communications Screen asshown above. SmartLink Fusion EMM Quick Setup Guide Rev3.1 25

27 11. SmartLink Residents Setup (EMM1) To Setup SmartLink Residents List on EMM1 Click the Smartlink, Residents List andthen AddNew button as shown below. Type eg Room 1 or Mrs Brown asthename Type eg 1001 asthecode (This is also known as the Client Account Number) Type eg asthephone Number (or Leave Blank) Click the Find buttontosearchforrecipient as shown below. Select eg Pager 1CC: andclick the Add Selected button as shown below. 26 SmartLink Fusion EMM Quick Setup Guide Rev3.1

28 Pager 1 CC: nowselectedintherecipient field. Click the Save & New button or the Save & Close button as shown below. Click the Add New button as shown below if you want to continue to ADD more SmartLink Residents. The SmartLink SCU2 Receiver, SmartWire System or SmartLine System are now ready to be tested as long as you programmed thecode/client Account to be Send Message Screen Click the Messages andthen Send Message. The Send Message Screen is displayed as shown below. SmartLink Fusion EMM Quick Setup Guide Rev3.1 27

29 13. Sent Items Screen Click the Messages and Sent Items. The Sent Items Screen is displayed as shown below. 14. Inbox Screen Click the Messages and Inbox. The Inbox Screen is displayed as shown below. 28 SmartLink Fusion EMM Quick Setup Guide Rev3.1

30 15. Active Alarms Screen Click the Messages and Active Alarms. The Active Alarms Screen is displayed as shown below. 16. Logging Out Click the Logout button as shown below. Copyright SmartLink A Division of Ness Corporation Pty Ltd November 2015 Unit 4/56 Norcal Rd, Nunawading VIC 3131 Australia Tel: Fax: smartlink@ness.com.au Web Site: To the best of our knowledge, the information contained in this manual is correct at the time of print. SmartLink A division of NESS CORPORATION PTY LTD reserves the right to make changes to the features and specifications at any time without prior notice in the course of product development. SmartLink Fusion EMM Quick Setup Guide Rev3.1 29