Simplified operation instructions for Samsung Shs-2320 Shark (this manual is unofficial and translated version only)

Transcription

1 Simplified operation instructions for Samsung Shs-2320 Shark (this manual is unofficial and translated version only) Registering Pin Number Perform this operation during door unlocked status 1. Press [Register button] (located at the battery compartment, remove cover) 2. Enter PIN number to be registered (4~12 digits) 3. Press Button Registering Card/Key tag 1. Press [Register button] 2. Place the card/key tag to be registered on the sensor 3. Press [Register button] again

2 Opening The door using Pin number (outside) 1. Place palm slightly on the [number pad] 2. When the number pad lights up, enter your Pin on the number pad 3. Press. *Double-Security mode 1. Place palm slightly on the [number pad] 2. When the number pad lights up, press the two random number that will appear on the screen 3. Enter Pin on the number pad 4. Press button. Opening the door (outside)card/keytag 1. Place palm slightly on the [number pad] 2. When the number pad lights up, place card/key tag on the sensor

3 Opening/closing the door from the inside Automatic Lock Mode 1. On the main body inside press [ 열림 / 닫힘 ] (open/close) button and the door will be lock or unlock Manual Lock mode 1. On the main body inside, Turn the manual switch knob to open or close, exposing green color indicates open status while red color indicates closed status Double/Normal Security mode setting 1.Press [register button] inside 2.Press [7] to set Double security Mode on the number pad or 3.Press [9] to set Normal lock mode on the number pad 4.Press button

4 Setting Authentication Sensor 1.Press [register button] inside 2.Press [1] to enable Authentication Sensor on the number pad or 3.Press [3] to disable Authentication Sensor on the number pad 4.Press button Setting Double authentication mode 1.Press [register button] inside 2.Press [4] to enable Double Authentication mode on the number pad or 3.Press [6] to disable Double Authentication mode on the number pad 4.Press button Setting Automatic Lock/Mabual lock Mode 1. On the main body inside switch automatic/manual lock mode By switching switch Adjusting Volume (Setting Sound) 1. On the main body inside, adjust sound by the following setting [1] Mute [2] Normal [3] Loud

5 Cancelling Alarms Invalid entry alarm (in case of multiple wrong password/card/key tag entry) 1. On the main body press [register] button or [open/close] button 2. Outside, press Pin followed by on the number pad, or place card/key tag on the sensor Intrusion alarm (outside) 1. On the main body press [register] button or remove one battery 2. Outside, press Pin followed by on the number pad, or place card/key tag on the sensor

6 How to use Emergency Battery 1. Using a 9V battery, make a contact by placing the 9V battery in an upward position connecting the polarity with the terminal node. 2. In this status you can now enter your Pin number, or place key tag/card To initialize the unit (refer to the illustrations) Battery replacement *Average Battery Lifetime 1.5V alkaline AA x 4 (ave. 10 operations per day) 1 year Please use alkaline battery only Replace Battery notification The battery icon will be lighted red and an alarm will go off signaling the need to replace battery.

7 Please change the battery at this time *please observe correct polarity placement when changing battery *please check battery for damage and leaks before changing *replace battery all at once, do not replace with used or mix new with old used ones. (Refer illustrations below) On the main body press the Battery cover release button, lift the cover up And replace the battery in this manner.

8 Trouble Shooting No power -check battery, if inserted correctly or check if in good condition Registration problem (PIN) -When registering please make sure to register pin within the 10 seconds time frame, when registration failed, try registering again. -check battery power if sufficient (CARD/KEYTAG) When registering card/keytag please make sure to register pin within the 10 seconds time frame, when registration failed, try registering again Door not unlocking Even after entering password and pressing [*] button -Make sure the password is registered first before trying to use. -Enter password when the number pad is lighted (slightly touch number pad first,when activated, enter pin number) Even after using Card/key tag to open door -Make sure the Card/key tag is registered first before trying to use -You should place the Card/key tag on the sensor correctly If double-lock feature is activated, you cannot open the door by password or key tag or card only When double-lock feature is enabled, you have to place palm slightly on the number pad first to activate, wait for the (bee~ree~reep sound) and then you can place card or key tag on the sensor to unlock the door. for instance the unit is not responding despite standard procedure is done, the unit may be defective and you should contact service center.

9 Auto-relock function not working - make sure you have set the unit to automatic lock mode - when set to manual mode, after closing the door, touch slightly the number pad, to initialize relock. *this event can also happen if the unit is installed incorrectly, for instances like these, please contact service center. * If the battery is completely discharged, the automatic lock feature does not work, please check power supply if sufficient. Number Pad is not activating -on the front body outside, beside the Power on/off button, press the reset button with a pin. *after standard procedure is done, but unit still not responding, contact service center Operation summary Pin registration/modify 1. Register button + enter pin + button Card/Keytag registration 1. Register button + place card/keytag on the sensor + register button again Opening door from inside 1. (Automatic) in locked status, press +open door 2. (Manual) turn manual lock knob to unlock position + open door Closing door from inside 1. (Automatic) press and the door will be locked 2. (Manual) turn manual lock knob to lock position and door will be locked

10 Opening the door from the outside Double security mode Card/key tag touch number pad + place card/key tag on the sensor. Pin - touch number pad + press the 2 random number that will appear + enter Pin number + button Closing the door from the outside Automatic Lock after closing the door, the automatic lock will activate Manual Lock touch number pad slightly, and the door will be locked Setting double security mode On Safe mode register button On normal mode - register button How to enable/disable double authentication mode Enable - register button Disable - register button Setting Automatic/Manual Lock mode Automatic- [ 자동 / 수동잠김 ] switch to automatic Manual - [ 자동 / 수동잠김 ] switch to manual Setting Sound volume Adjust volume setting loud Enable/disable Authentication Sensor Enable - register button Disable - register button Setting anti-hack feature Enable- after closing the door, press from low, normal & button Disable-enter password, or place key tag/card on sensor. Turn-off alarm(inside) Press register button Turn-off alarm(outside) Enter Pin or place card/key tag on the sensor