How to upgrade firmware of Pi-931-X34CC and Pi-931-XA5 reader module
|
|
- Amy Golden
- 6 years ago
- Views:
Transcription
1 S i l i c o n C r a f t How to upgrade firmware of Pi-931-X34CC and Pi-931-XA5 reader module Revision History Revision Date Description Change/Updated/Comment 1.0 February st Release 2.0 July 2012 Data Correction 1. Change UART to UART(TTL) for all over the document. 2. Section change P5(reset) to P3(DVDD). 3. Insert section Old section becomes section Section remove text Jumping wire can be removed. Copyright 2011, All Rights Reserved. No part of this publication may be reproduced or distributed in any form or by any means, or stored in a data base or retrieval system, without prior written permission from Silicon Craft Co.,Ltd. by Mukkaphol Wattanacharoen Under authorized of Product Development division Silicon Craft Co.,Ltd. The information herein is for product information purpose. While the contents in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. Page 1 of 11
2 1. Introduction This document describes how to upgrade firmware of Pi-931-X34CC and Pi-931-XA5 reader module via USB port using USB to UART(TTL) converter. Pi-931 uses STM32F103 as a microcontroller to control SIC9310 reader IC. User can upgrade firmware of STM32F103 on Pi-931 board to improve the operations and performance of each upgrades. This application note only shows USB connection method via USB to UART(TTL) converter. 2. Getting Start 2.1 System requirements This is the list of the necessary components which user needs to use in downloading process. Please remind that these components are not included in Pi-931 box set except the Pi-931 board. Pi-931 board, X34CC or XA5 Model, all jumper removed. A personal computer with these specifications : o Operating System: Windows XP or higher o CPU and memory : Refer to each Window s specifications o Free space: At least 10 MB left in HDD o Port: Serial(COM) Port or USB Port STM s Flash Loader Demo version software setup package o Please Check W_DEMO&ClassID=1734 and click the zip icon as show in Fig.1 below Fig.1 Download link for STM Flash Loader Software Demo version Page 2 of 11
3 PC Connection(Note: This application note only uses USB connection method) o Serial Connection method (COM Port) Serial Cable RS-232 to UART(TTL) converter Connection Cable(Please see Fig.7 for details) o USB Connection method (USB Port with virtual COM Port Driver) USB Cable USB to UART(TTL) converter Connection Cable(Please see Fig.8 for details) Jumping wire Jumper Firmware.hex code Fig.2 All components Fig.3 USB Cable Page 3 of 11
4 Fig.4 USB to UART(TTL) converter Fig.5 Jumping wire Fig.6 Connection wire 2.2 Software installation ST Microsystem Flash Loader Demo version Please see ST Microsystems s User Manual number UM0462 for details. AL/CD pdf USB to UART(TTL) converter driver In case of using USB to UART(TTL) converter, user must install the driver according by each converter. Please see the manual of the converter for details. Page 4 of 11
5 3. How to download updated firmware to Pi Checking port number and properties Windows XP Click Start Control Panel System Hardware Device manager Ports(COM&LPT) Remember the port number e.g. COM To find out each COM port properties such as baud rate and frame format, right click on the port number, Select Properties Port Settings Recommended settings shows as Fig Windows Vista/ Click Start Control Panel Device manager Ports (COM&LPT) Remember the port number e.g. COM To find out each COM port properties such as baud rate and frame format, right click on the port number, Select Properties Port Settings Recommended settings shows as Fig.7 Fig.7 Recommended Port Settings Page 5 of 11
6 3.2 Connect to Pi Serial Port with RS-232 to UART(TTL) converter For Serial port, connect the cable as seen in Fig. 8 GND GND Serial Cable RS-232 to UART Converter TXD RXD 5V (Optional) TXD RXD 5V Pi USB Port with USB to UART(TTL) converter For USB Port, connect the cable as seen in Fig. 9 Fig.8 RS-232 Cable Connection GND GND USB Cable USB to UART Converter TXD RXD 5V (Optional) TXD RXD 5V Pi Access STM32F103 Boot Loader Fig.9 USB Cable connection Connect Jumping wire between pin1(b0) and pin3(dvdd) at 5-pin connector (JP1 for Pi-931- X34CC and JP2 for Pi-931-XA5) Power up Pi-931 Fig.10 Jumping wire Connecting If user uses USB power, sets jumper to USB Position at Power Source Connector (JP3 for Pi931- X34CC and JP1 for Pi-931-XA5) If user uses external +5V Power, set jumper to UART(TTL) Position at Power Source Connector (JP3 for Pi931-X34CC and JP1 for Pi-931-XA5) If user uses external adaptor power (for Pi-931-XA5 only), set jumper to J1 position If the process is correct, the blue LED will not light Remove jumping wire, then select UART interface by setting the jumper at INFSEL position User can access STM32F103 boot loader now. Page 6 of 11
7 3.4 Download Hex Code to Pi-931 Note: Please see ST Microsystems s User Manual number UM0462 for details. Step 1. Open Flash Loader Demo program Step 2. In the Connecting screen, settings as Fig.10 and click Next Fig.10 Connection settings Step 3. Click Remove Protection. After the process finish, click Next Note: This step will erase all the data in the STM32F103 Page 7 of 11
8 Fig.11 Read protected warning Fig.12 Protection removed Page 8 of 11
9 Step 4. In the device information screen, settings as Fig.13, then click Next Fig.13 Device information Step 5. In the operation screen, Click Download to Device and Select the firmware.hex file by click button, after selection, do the settings as Fig.14 Fig.14 Download to device Page 9 of 11
10 Step 6. Waiting for programming and verification process, then click Back Fig.15 Download to device complete Step 7. Select Enable Read protection as Fig.16, then click Next Step 8. Click Finish Fig.16 Enable read protection Page 10 of 11
11 3.5 Reset Pi Turn-off the power source Set Jumper back to user s configuration and turn-on the power source Pi-931 is now upgraded and ready to use Page 11 of 11
Updating Reader Firmware
SWH-xxxx Readers Updating Reader Firmware Version C0 Document Part Number UM-096 July 2012 OVERVIEW This document describes how to download new firmware to Software House SWH-4xxx readers. The procedure
More informationInstructions manual / DPC Touch Firmware Upgrade 1. DPC Touch Firmware Upgrade SERVICE MANUAL
Instructions manual / DPC Touch Firmware Upgrade 1 DPC Touch Firmware Upgrade SERVICE MANUAL Instructions manual / DPC Touch Firmware Upgrade 2 IMPORTANT The tool delivered with this manual may have been
More informationWiFi to RS-232 adapter user manual
WiFi to RS-232 adapter user manual WiFi to RS-232 adapter Package Contents: WiFi RS-232 adapter x 1 A4 User manual x 1 Mini USB Cable x 1 White Box Dimension: 11 x 6 x 5 (cm) Total Package Weight: 126
More informationBCOM-USB Device. User Manual.
BCOM-USB Device User Manual www.kalkitech.com Version 2.1.2, December 2017 Copyright Notice 2017 Applied Systems Engineering, Inc. All Rights reserved. This user manual is a publication of Applied Systems
More informationFigure 1. JTAGAVRU1 application The JTAGAVRU1 is supported by AVR Studio. Updated versions of AVR Studio is found on
JTAG AVR Emulator through USB Main Features AVR Studio Compatible Supports AVR Devices with JTAG Interface Emulates Digital and Analog On-Chip Functions Data and Program Memory Breakpoints Supports Assembler
More informationBoot Loader for the Z51F6412 MCU
Boot Loader for the Z51F6412 MCU AN037701-0215 Abstract This application note discusses how to create a boot loader program for the Z51F6412 microcontroller, a member of Zilog s Z8051 Family of Microcontrollers.
More informationNeo_M660 GPRS Module Demo Board User Guide Version 1.0
Neo_M660 GPRS Module Demo Board User Guide Version 1.0 Revision Record Issue Changes Date V1.0 Initial draft 2014-05 Copyright Neoway Technology Co., Ltd i Contents 1 Overview... 1 2 Interfaces... 1 3
More informationWireless M-Bus Suite for Panasonic Evaluation Boards. Quick Start Guide
Wireless M-Bus Suite for Panasonic Evaluation Boards January 16, 2012 page 2 Document History 1.0 2011-07-20 First release dj 1.1 2011-07-25 Review dj 1.2 2011-07-27 Quick start changed dj 1.3 2011-09-13
More informationUser s Manual Closer to Real, Zigbee Module ZIG-100. Wireless Communication. ROBOTIS CO.,LTD
User s Manual 2006-07-06 Closer to Real, Wireless Communication ROBOTIS CO.,LTD. www.robotis.com +82-2-2168-8787 Contents 1. Page 02 2. Zigbee Setting Page 06 3. PC Interface Zig Board Schematic Page 10
More informationStarter Guide Version Sphinx Access Control System
TC3XYMT/TC3XYNT Starter Guide Version 1.04.1 Sphinx Access Control System Page 1 1. Controller and Reader wiring...3 2. Connect the controller to PC...4 2.1. Setup the ID of Controller...4 2.2. Connect
More informationAN LPC1700 secondary USB bootloader. Document information. LPC1700, Secondary USB Bootloader, ISP, IAP
LPC1700 secondary USB bootloader Rev. 01 8 September 2009 Application note Document information Info Keywords Abstract Content LPC1700, Secondary USB Bootloader, ISP, IAP This application note describes
More informationSPBT3.0DPx BT module. Firmware Update Procedure. Revision 1.0
SPBT3.0DPx BT module Firmware Update Procedure Revision 1.0 Agenda 2 Introduction Frequently Asked Questions Procedure Overview Hardware Setup Software Setup Introduction 3 Why ST customers should take
More informationMOD-RFID125 User Manual. All boards produced by Olimex are ROHS compliant. Rev.A, February 2008 Copyright(c) 2008, OLIMEX Ltd, All rights reserved
MOD-RFID125 User Manual All boards produced by Olimex are ROHS compliant Rev.A, February 2008 Copyright(c) 2008, OLIMEX Ltd, All rights reserved INTRODUCTION: FEATURES: MOD-RFID125 is an RFID station,
More informationCommercial-grade Interface Converter User Manual
Suzhou Huarui Thermal Control Co.,Ltd Commercial-grade Interface Converter User Manual Read this manual carefully before installation and use! The document is the exclusive property of SUZHOU HUARUI Thermal
More informationQUICK START GUIDE FOR FIRMWARE UPGRADE RS232-TO UART INTERFACE BOARD AND SOFTWARE
QUICK START GUIDE FOR FIRMWARE UPGRADE RS232-TO UART INTERFACE BOARD AND SOFTWARE DESCRIPTION RS232-TO-UART Interface board is a PC- Serial-Port-to-UART adaptor that uses a customise Toshiba application
More informationDIO16 8 Channel digital input and 8 Channel digital output board. V1.0 August CANBUS-DIO16 Rev B v1.0
DIO16 8 Channel digital input and 8 Channel digital output board V1.0 August 2017 Product name Model number Manufacturer DIO16 8 Channel digital input and 8 Channel digital output board CANBUS-DIO16 SK
More informationSTM32 F4xx Discovery Board Setup Guide
STM32 F4xx Discovery Board Setup Guide Audio Weaver November 2016 Copyright Information 2014 DSP Concepts, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express
More informationFirmware Loader. Software. For support mail to: tech mca.nl See also our website: mca.com. Software Manual. Revision 1.
Firmware Loader Software For support mail to: tech support@smac mca.nl See also our website: www.smac mca.com Software Manual Revision 1.0 www.ingeniamc.com Firmware Loader Software Manual Copyright and
More information3.1 I-7560 Pin Assignment and Specifications: Introduction
3.1 I-7560 Pin Assignment and Specifications: Introduction The I-7560 adds a Windows serial Com port via its USB connection and is compatible with new & legacy RS-232 devices. USB Plug and Play allows
More information+ (5~27 VDC) GND. Bluetooth V4.1 BLE RS-232 Serial Adapter. Model: BLE-232B. 1. Package content: BLE RS-232 adapter
Bluetooth V4.1 BLE RS-232 Serial Adapter 1. Package content: BLE RS-232 adapter Model: BLE-232B Package Contents: BLE RS-232 adapter x 1 Screw x2, Screw nut x 2 A4 User manual x 1 Mini USB Cable x 1 White
More informationProgrammer for flash micro computers. User s Manual
Programmer for flash micro computers User s Manual TESSERA Technology INC. 6th edition 9/2008 Table of Contents Chapter 1 Summary 2 1.1 System Configuration 3 Chapter 2 Installation 4 2.1 System Requirement
More informationTRP-C08. USB to RS232/422/485 Isolated Converter. User s Manual. Printed Sep.2014 Rev 1.4
TRP-C08 USB to RS232/422/485 Isolated Converter User s Manual Printed Sep.2014 Rev 1.4 Trycom Technology Co.,Ltd No.35, Zhongxing Rd., Guishan Township, Taoyuan County 333, Taiwan. Tel : 886-3-350-3351
More informationMegaAVR-DEVelopment Board Progressive Resources LLC 4105 Vincennes Road Indianapolis, IN (317) (317) FAX
MegaAVR-DEVelopment Board Progressive Resources LLC 4105 Vincennes Road Indianapolis, IN 46268 (317) 471-1577 (317) 471-1580 FAX http://www.prllc.com GENERAL The MegaAVR-Development board is designed for
More informationMOD-RFID125-BOX User Manual
MOD-RFID125-BOX User Manual All boards produced by Olimex are ROHS compliant Rev.B, May 2011 Copyright(c) 2011, OLIMEX Ltd, All rights reserved Page 1 INTRODUCTION: FEATURES: MOD-RFID125-BOX is an RFID
More informationAMS COCKPIT USERS GUIDE. AMS Cockpit Version 1.1 USERS GUIDE
AMS COCKPIT USERS GUIDE Table of Contents AMS Cockpit Version 1.1 USERS GUIDE Revision Date: 1/15/2010 A d v a n c e d M i c r o S y s t e m s, I n c. w w w. s t e p c o n t r o l. c o m i Table of Contents
More informationUser Manual For CP-JR ARM7 USB-LPC2148 / EXP
CP-JR ARM7 USB-LPC2148 / EXP 38 CR-JR ARM7 USB-LPC2148 which is a Board Microcontroller ARM7TDMI-S Core uses Microcontroller 16/32-Bit 64 Pin as Low Power type to be a permanent MCU on board and uses MCU
More informationBV511 Hardware Guide ByVac ByVac Revision 1.0
BV511 Hardware Guide ByVac ByVac 2007 www.byvac.co.uk Revision 1.0 ByVac 1 Copyright in this work is vested in ByVac and the document is issued in confidence for the purpose only for which it is supplied.
More information8051 Intermidiate Development Board. Product Manual. Contents. 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help
8051 Intermidiate Development Board Product Manual Contents 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help 1. Overview 2. Features The board is built on a high quality FR-4(1.6
More informationUSB/RS232 TO cctalk COMMUNICATION BOARD Technical Information
USB/RS232 TO cctalk COMMUNICATION BOARD Technical Information USB/RS232 to CcTalk COMMUNICATION BOARD 18/04/2016 Manual code: 81043530 ATTENTION: Read this technical manual carefully before installing
More information+ (5~27 VDC) GND. Bluetooth V4.2 BLE RS-232 Serial Adapter. Model: BLE-232D-E. 1. Package content: BLE RS-232 adapter
1. Package content: BLE RS-232 adapter Bluetooth V4.2 BLE RS-232 Serial Adapter Model: BLE-232D-E Package Contents: BLE RS-232 adapter x 1 A4 User manual x 1 Mini USB Cable x 1 White Box: 11 x 6 x 5 (cm)
More informationCOMBI-Modul 167. Installation and Getting Started Guide. Edition March A Product of PHYTEC Technologie Holding AG
COMBI-Modul 167 Installation and Getting Started Guide Edition March 2001 A Product of PHYTEC Technologie Holding AG COMBI-Modul 167 In this manual are descriptions for copyrighted products which are not
More informationUM2051 User manual. Getting started with the STM32 Nucleo pack for USB Type-C and Power Delivery. Introduction
User manual Getting started with the STM32 Nucleo pack for USB Type-C and Power Delivery Introduction The STM32 Nucleo pack for USB Type-C and Power Delivery (P-NUCLEO-USB001) is a kit based on a NUCLEO-F072RB
More informationAVR-P20 development board Users Manual
AVR-P20 development board Users Manual All boards produced by Olimex are ROHS compliant Revision A, October 2005 Copyright(c) 2009, OLIMEX Ltd, All rights reserved Page 1 INTRODUCTION: The AVR Microcontrollers
More information6 foot USB to RS-232 Serial Adapter DB-9 Male, FTDI Chipset. Product Manual. Coolgear Version 1.0 January 2018 Model Number: USBG-232MM
6 foot USB to RS-232 Serial Adapter DB-9 Male, FTDI Chipset Product Manual Coolgear Version 1.0 January 2018 Model Number: USBG-232MM 2 USBG-232MM PRODUCT MANUAL Revision History Revision Date Author Comments
More informationManual of Board ET-PIC STAMP 18F8722-K22 ET-PIC STAMP 18F8722-K22
ET-PIC STAMP 18F8722-K22 ET-PIC STAMP 18F8722-K22 is Board Microcontroller in a series of PIC18F87K22 80-Pin TQFP from Microchip. It designs I/O of MCU on board to interface with CONNECTOR in the format
More informationELAD EXTIO-232 CAT RS232 interface with band output for FDM-DUO
ELAD EXTIO-232 CAT RS232 interface with band output for FDM-DUO USER MANUAL www.eladit.com Contents Revision History... 3 1 Overview... 4 2 CAT Commands... 4 3 Band Select Output... 5 4 Firmware Upgrade...
More informationThis 4-port RS-422/485 Adapter is provided with an external switching power adapter in the package.
USB-4COMi-M USB to Quad RS-422/485 to Serial Adapter Manual The USB to Industrial Quad RS-422/485 Adapter is designed to make industrial communication port expansion quick and simple. Connecting to a USB
More informationNCOM SERIAL DEVICE SERVER 1XX SERIES USER S MANUAL
NCOM SERIAL DEVICE SERVER 1XX SERIES USER S MANUAL 2017-07-07 Edition Titan Electronics Inc. Web: www.titan.tw Contents 1. INTRODUCTION... 4 1.1 Key Features... 5 1.2 Specifications... 6 2. PANEL LAYOUT
More informationMegawin 8051 ISP via COM Port
Megawin 8051 ISP via COM Port User Manual By Vincent Y. C. Yu This document information is the intellectual property of Megawin Technology Co., Ltd. 1 Contents 1 What is ISP... 3 2 Chip Configuration for
More informationNote : Power consumption and sample rate will vary according to different firmware versions.
1.0 Product Page 1 of 5 PenMount 1201A control board is one of the cutting-edge innovations from PenMount. A collectively integrated feature with USB / RS232 interface supporting 5 to 7.9 projected capacitive
More informationAFEDRI SDR 192kHz firmware upgrade process description.
AFEDRI SDR 192kHz firmware upgrade process description. 1. Attention!!! Please run SDR Control software before firmware upgrade process beginning. Switch to tab About and write value of Front End Main
More informationUSB485. USB to RS485 Converter Card. User Manual for connecting with Windows Vista Version 1.01
USB485 USB to RS485 Converter Card User Manual for connecting with Windows Vista Version 1.01 RMS Technologies 2533 N. Carson St. #4698, Carson City, NV 89706-0147 1-877- 301-3609 www.rmsmotion.com sales@rmsmotion.com
More informationNote : Power consumption and sample rate will vary according to different firmware versions.
1.0 Product Page 2 of 6 PenMount 1400A control board is one of the cutting-edge innovations from PenMount. A collectively integrated feature with USB / RS232 interface supporting 11.0 to 15.0 projected
More informationSTEPPER-MOTOR-RD STEPPER MOTOR REFERENCE DESIGN KIT USER S GUIDE. 1. Kit Contents. 2. Kit Overview. Figure 1. Stepper Motor Reference Design Board
STEPPER MOTOR REFERENCE DESIGN KIT USER S GUIDE 1. Kit Contents The Stepper Motor Reference Design Kit contains the following items: Stepper Motor Reference Design Board Stepper Motor Universal AC to DC
More informationBluetooth V4.1 BLE RS-232 Serial Adapter Model: BLE-232B Bluetooth V4.2 BLE RS-232 Serial Adapter Model: BLE-232C
Bluetooth V4.1 BLE RS-232 Serial Adapter Model: BLE-232B Bluetooth V4.2 BLE RS-232 Serial Adapter Model: BLE-232C Applications: MSR card reader reader, RFID reader, IC card reader, Specifications: 1. Baud
More informationAC-PG-USBASP USBASP AVR Programmer
AC-PG-USBASP USBASP AVR Programmer User Guide Download drivers from Jaycar website under the product download section TABLE OF CONTENTS 1. OVERVIEW... 2 1.1. Introduction... 2 1.2. References... 2 1.2.1.
More informationMatrix-710. Linux-Ready Cortex-A5 Industry IoT Gateway. Hardware Guide. Version: Nov.
Matrix-710 Linux-Ready Cortex-A5 Industry IoT Gateway Hardware Guide Version: 1.01 2017 Nov. Copyright Artila Electronics Co., Ltd. All Rights Reserved Trademarks The Artila logo is a registered trademark
More informationHow to upgrade the firmware on the STEVAL-USBC2DP USB Type-C to DisplayPort adapter
UM378 User manual How to upgrade the firmware on the STEVAL-USBCDP USB Type-C to DisplayPort adapter Introduction The STSW-USBCDP software package contains application firmware in binary and in.dfu file
More informationFlasher PC Application
Flasher PC Application The operation and functions described in this manual are available from Software Version V2.5 onwards. Specifications & Ordering: Models, Sales Order Parts: PC-Net-014 Applications
More informationTRP-C06H User s Manual
TRP-C06H User s Manual 2-Port RS-232 to RS-422/485 Isolated Converter Printed Feb.2007 Rev 1.1 Trycom Technology Co., Ltd 1F, No.2-11, Sihu street, Hinge Township, Taipei, Taiwan ROC Tel: 886-2-86781191,
More informationProduct Manual. Mini USB to Terminal RS422 RS485 FTDI Plug-in Adapter. Coolgear, Inc. Version 1.1 April 2018 Model Number: USBG-422MiNi
Mini USB to Terminal RS422 RS485 FTDI Plug-in Adapter Product Manual Coolgear, Inc. Version 1.1 April 2018 Model Number: USBG-422MiNi 2 USBG-422MiNi Product Manual Revision History Revision Date Author
More informationMini USB to RS-232 Serial Adapter DB-9 Male Converter. Product Manual. Coolgear Version 1.0 January 2018 Model Number: USBG-232MINI.
Mini USB to RS-232 Serial Adapter DB-9 Male Converter Product Manual Coolgear Version 1.0 January 2018 Model Number: USBG-232MINI 2 USBG-232MINI PRODUCT MANUAL Revision History Revision Date Author Comments
More informationUM2343 Application note
Application note EVALKITST8500-1: getting started with ST8500 evaluation kit Introduction The EVALKITST8500-1 is a platform which allows an easy way to evaluate the features and performance of a power
More informationNFC NUTSHELL KIT. MCU Modules USER MANUAL REVISION GMMC GmbH Keywords Abstract. Document information
USER MANUAL REVISION 1.23 Document information Info Keywords Abstract Content User Manual GMMC This document describes how to use of the GMMC s NFC Nutshell KIT and its related tools GMMC GmbH www.gmmc-biz.com
More informationFirmware Reprogramming Guide
8 July. 2016 1 UART Connection Hardware Setup Modules and adaptors may be reprogrammed using the procedure detailed in this document. Normally, our platforms will be delivered with the final firmware already
More informationFirmware/Bootloader Update Manual
UEL6000 Ethernet Firmware/Bootloader Update Manual General Remarks The only purpose of this manual is a description of the product. It must not be interpreted as a declaration of conformity for this product
More informationLPC2148 DEV BOARD. User Manual.
LPC2148 DEV BOARD User Manual www.coineltech.com www.coineltech.com Designed by CoiNel Technology Solutions LLP No-816, 2 nd Floor, 4 th B Cross, 9 th A Main, RPC Layout, Vijaynagar, Bangalore-560040 State:
More informationSTM32 F7xx Discovery Board Setup Guide
STM32 F7xx Discovery Board Setup Guide Audio Weaver May 2017 Copyright Information 2016-2017 DSP Concepts, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express
More informationUser Manual. August 2008 Revision 1.0. SKH300 ibutton Reader Configuration Utility
User Manual August 2008 Revision 1.0 SKH300 ibutton Reader Configuration Utility Copyright 2008 Jan. All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change
More informationTEOS Hardware System TEOS 8416 / TEOS 1016/ TEOS1216
TEOS Hardware System TEOS 8416 / TEOS 1016/ TEOS1216 Revision v1.1 November 2011 Copyright 2009~2011 All Rights Reserved Manual Version 1.1 The information contained in this document is subject to change
More informationUSB to RS-422 / 485. US USB To Serial Operation Manual
USB to RS-422 / 485 US-101-485 USB To Serial Operation Manual First Edition, Jun 2008 Table of Contents 1. Introduction 2 2. Package checklist 3 3. Product Specification 4 4. Product Panel Views Description
More informationFirmware Update MiniMod
This manual explains how to update the firmware of a MiniMod board. Firmware Update MiniMod The procedure is valid for the hardware versions v2.1, v2.2, v2.3, v2.4 and v2.5. Please check that your hardware
More information8051 Basic Development Board. Product Manual. Contents. 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help
8051 Basic Development Board Product Manual Contents 1) Overview 2) Features 3) Using the board 4) Troubleshooting and getting help 1. Overview 2. Features The board is built on a high quality FR-4(1.6
More informationingenia dspic bootloader User s Guide
ingenia dspic bootloader User s Guide version 1.3 24/07/06 2006, ingenia-cat S.L. ingenia dspic bootloader Guide: V1.3 Copyright 2006 ingenia-cat S.L. Permission is granted to copy and/or distribute this
More informationSIM800H&L_EVM_User Guide _V1.00
SIM800H&L_EVM_User Guide _V1.00 Document Title: SIM800H&L_EVM_User Guide Version: 1.00 Date: Status: Document Control ID: Release SIM800H&L_EVM_User Guide_V1.00 General Notes SIMCom offers this information
More informationSerial Bluetooth Smart Adapter - RS232, Low Energy 4.2 BLE Datasheet and Quick Reference for USBLE232C
Serial Bluetooth Smart Adapter - RS232, Low Energy 4.2 BLE Datasheet and Quick Reference for USBLE232C Package content: BLE RS-232 adapter x 1 Screws for DB9 connector x 2 Nuts for DB9 connector x 2 User
More informationAVR-P development board Users Manual
AVR-P40-8515 development board Users Manual All boards produced by Olimex are ROHS compliant Revision A, January 2002 Copyright(c) 2009, OLIMEX Ltd, All rights reserved Page 1 INTRODUCTION: The AVR Microcontroller
More informationProduct Manual. USB to Optical Adapter Industrial Isolated RS- 232/422/485. Coolgear, Inc. Version 2.1 December 2018 Model Number: USB-COMi-Si-M
USB to Optical Adapter Industrial Isolated RS- 232/422/485 Product Manual Coolgear, Inc. Version 2.1 December 2018 Model Number: USB-COMi-Si-M 2 USB-COMi-SI-M Product Manual Revision History Revision Date
More informationZCRMZNICE01ZEMG Crimzon In-Circuit Emulator
Quick Start Guide QS006602-0408 Introduction Zilog s ZCRMZNICE01ZEMG Crimzon (ICE), shown in Figure 1, provides Crimzon chip family emulation with a Trace and Event system for program debugging using Zilog
More informationNCOM SERIAL DEVICE SERVER 4XX SERIES USER S MANUAL
NCOM SERIAL DEVICE SERVER 4XX SERIES USER S MANUAL 2017-07-07 Edition Titan Electronics Inc. Web: www.titan.tw Contents 1. INTRODUCTION... 4 1.1 Key Features... 5 1.2 Specifications... 6 2. PANEL LAYOUT
More informationI-7570 Serial To HART Converter
I-7570 Serial To HART Converter User s Manual Warranty All products manufactured by ICP DAS are under warranty regarding defective materials for a period of one year from the date of delivery to the original
More information78M6618 PDU1 Firmware Quick Start Guide
78M6618 PDU1 Firmware Quick Start Guide July 2012 Rev. 0 UG_6618_122 Table of Contents 1 Introduction... 3 1.1 What s Included with an EVK?... 4 1.2 What s included with an SDK?... 5 1.3 Other Development
More informationFigure 1-1 ISPAVRU1 application
ISP AVR Programmer through USB Main Features AVR Studio Interface (AVR Studio 4.12 or later) Supports all AVR Device with ISP interface, refer to AVR Studio Programs both Flash and EEPROM Supports Fuse
More informationProgramming and Cloning BL6xx and RM1xx Modules with the QPK-NRF5x-01
A Programming and Cloning BL6xx and RM1xx Modules with the QPK-NRF5x-01 v2.1 INTRODUCTION This document provides a step-by-step guide for upgrading and production cloning of Laird BL6XX and RM1xx modules
More informationPCL Port RS-232 Interface Card
PCL-858 8-Port RS-232 Interface Card Copyright Notice This documentation and the software included with this product are copyrighted 2001 by Advantech Co., Ltd. All rights are reserved. Advantech Co.,
More informationibl ingenia dspic bootloader Users s guide 2007, ingenia-cat S.L. 06/06/07 Version 1.4
ingenia dspic bootloader Users s guide 06/06/07 Version 1.4 2007, ingenia-cat S.L. User s guide Copyright and trademarks Copyright 2007 ingenia-cat, S.L. Microchip, MPLAB and dspic are registered trademarks
More informationFB2550 to FB2558 Upgrade Kit Revision /18
Bulletin 51438 FB2550 to FB2558 Upgrade Kit Revision 1.0 08/18 Desktop, Rack Mount & Panel Mount Enclosures Instructions (34214 kit) 1. Shut down the FB2550 using the F5 key. 2. Once properly shut down,
More informationUSB Port USB Serial DB-9 RS-232 Adapter FTDI Chipset. Product Manual. Coolgear Version 1.0 January 2018 Model Number: USB2-4COM-M
USB 2.0 4-Port USB Serial DB-9 RS-232 Adapter FTDI Chipset Product Manual Coolgear Version 1.0 January 2018 Model Number: USB2-4COM-M 2 USB2-4COM-M PRODUCT MANUAL Revision History Revision Date Author
More informationELMO Board Programming Guide
ELMO Programming Guide 1(18) ELMO Board Programming Guide Version history Version Date Author Changes 0.1 17.08.2015 CCZI First draft 0.2 18.08.2015 CCZI Added ToC, Clarified section 2.2: SB12-SB14 solder
More informationSerial Bluetooth Smart Adapter - RS232, Low Energy 4.1 BLE Datasheet and Quick Reference for BLE232V2
Serial Bluetooth Smart Adapter - RS232, Low Energy 4.1 BLE Datasheet and Quick Reference for BLE232V2 Package content: BLE RS-232 adapter x 1 Screws for DB9 connector x 2 Nuts for DB9 connector x 2 User
More informationAN4045 Application note
Application note STM32F3 series in-application programming (IAP) using the USART Introduction An important requirement for most Flash-memory-based systems is the ability to update the firmware when installed
More informationAVR 40 Pin Rapid Robot controller board
AVR 40 Pin Rapid Robot controller board User Manual Robokits India http://www.robokits.org info@robokits.org - 1 - Thank you for purchasing the AVR 40 Pin Rapid Robot controller board. This unit has been
More informationv1.2 Closer to Real, USB2Dynamixel User s Manual ROBOTIS CO.,LTD.
v1.2 Closer to Real, USB2Dynamixel User s Manual ROBOTIS CO.,LTD. www.robotis.com contents 1. Introduction 2 1-1. Functions 2 1-2. Composition 3 1-3. System Requirements 3 1-4. USB2Dynamixel Connection
More informationSmartVR. Quick Start Guide. Release 2.0
SmartVR Quick Start Guide Release 2.0 www.veear.eu Table of Contents Introduction Read this first!... 3 SmartVR Product Description... 3 Hardware Setup... 4 Software Installation... 5 Running your first
More informationUpdating the Firmware in the BAM-1020 Particulate Monitor
Met One Service Bulletin Revised: February 12, 2009 Met One Instruments, Inc. 1600 N.W. Washington Blvd. Grants Pass, OR 97526 (541) 471-7111 www.metone.com Updating the Firmware in the BAM-1020 Particulate
More informationQuick Start Guide SBC21/NSD21/EC 21 SBC21 / EC21 / NSD21. Quick Start Guide. Copyright IC Nexus Corporation. All rights reserved
SBC21 / EC21 / NSD21 Quick Start Guide Copyright 2000 2013 IC Nexus Corporation. All rights reserved Release Notes Version Release Date Notes 1.0 June 2013 Initial release 2.0 October 2013 Correct some
More informationTechnical Advisory Bulletin
Date: Monday, December 13, 2010 Number: TAB-09-010 To: US Distributors Notice: GS3055-I & GS3060 Flash Update Utility This is to advise you that DSC has released the GS3055-I and GS3060 Flash Update Utility
More informationManual for Q1900G4 Nano Motherboard v1.1
Manual for Q1900G4 Nano Motherboard v1.1 Catalogue I Product Description... 2 1. Brief Introduction... 2 2. Version Specification... 2 3. Characteristics & Performances... 2 II Product Overview... 3 1.
More informationEVALKITSTKNX. Miniature transceiver STKNX evaluation and development kit. Features
Miniature transceiver STKNX evaluation and development kit Data brief Features Full KNX twisted pair device development kit based on the STKNX miniature transceiver Controlled by STM32F103 microcontroller
More informationEARTH PEOPLE TECHNOLOGY. VISIPORT 2 USB To Serial Adapter User Manual
EARTH PEOPLE TECHNOLOGY VISIPORT 2 USB To Serial Adapter User Manual The VisiPort 2 is a USB To Serial Adapter Module that is compact in size and programs any Arduino. It's small size allows it to fit
More informationMicrocontroller. BV523 32bit Microcontroller. Product specification. Jun 2011 V0.a. ByVac Page 1 of 8
32bit Product specification Jun 2011 V0.a ByVac Page 1 of 8 Contents 1. Introduction...3 2. Features...3 3. Physical Specification...3 3.1. PIC32...3 3.2. USB Interface...3 3.3. Power Supply...4 3.4. Power
More informationT1K MODBUS Base Controller Specifications
Base Controller 1 2 In This Chapter.... Base Controller Setting the DIP Switches Setting the Rotary Address Switches Port Pin out and Wiring RJ12 Serial Port Pin out and Wiring 2 2 Base Controller General
More informationUSB485 USB to RS485 Converter Card
USB485 USB to RS485 Converter Card User Manual Version 1.02 RMS Technologies 2533 N. Carson St. #4698, Carson City, NV 89706-0147 1-877-301-3609 www.rmsmotion.com sales@rmsmotion.com Thank you for purchasing
More informationModel 5100 Bootloader Installation Guide
Model 5100 Bootloader Installation Guide The information in this document is current as of the following Hardware and Firmware revision levels. Some features may not be supported in earlier revisions.
More informationET-MINI RS422/485 ISOLATION
Manual of Board ET-MINI RS4/485 ISOLATION ET-MINI RS4/485 ISOLATION ET-MINI RS4/485 ISOLATION is the set of Line Driver to convert Signal Connection of PORT UART/USART as TTL Type from Microcontroller
More informationCoiNel Technology Solutions LLP. LPC2148 ARTIST Instruction Manual LPC2148 ARTIST. Instruction manual. Revision 1
LPC2148 ARTIST Instruction manual Designed by CoiNel Technology Solutions LLP No-816, 2 nd Floor, 4 th B Cross, 9 th A Main, RPC Layout, Vijaynagar, Bangalore-560040 State: Karnataka Country: India www.coineltech.com
More informationLPC2468 Industrial Reference Design Platform System Development Kit Version 1.2. August 2008
QuickStart Guide LPC2468 Industrial Reference Design Platform System Development Kit Version 1.2 August 2008 1.0 System Overview The LPC2468 Industrial Reference Design (IRD) is a platform targeted at
More informationUSB-16COMi-M 16-Port RS-422/485 USB Serial Adapter User Manual. Features and Specifications. Power Supply
USB-16COMi-M 16-Port RS-422/485 USB Serial Adapter User Manual The USB to industrial 16-Port RS-422/485 Adapter is designed to make serial port expansion quick and simple. Connecting to a USB port on your
More informationmbed Kit User Guide of NQ62x daughter board
mbed Kit User Guide of NQ62x daughter board mbed Kit User Guide Sheet 1 of 10 Nov 17, 2016 Index: 1. Introduction... 4 1.1 Minimum Requirements... 4 2. Kit Content... 4 2.1 DELTA DFXE-SM001 mbed kit hardware
More informationEX & EX-45362IS 2S RS232/422/485 3-in-1 Serial PCIe Card
EX-45362 & EX-45362IS 2S RS232/422/485 3-in-1 Serial PCIe Card Congratulation on your purchasing this high performance 2-Port RS232/422/485 3-in-1 Serial PCIe Host Adapter. The adapter is high speed PCIe
More information