COMDEK INDUSTRIAL CORPORATION 9F-1,

Transcription

1 Owner s Manual MD-680P Palm Pulse Oximeter COMDEK INDUSTRIAL CORPORATION 9F-1, No. 3, Yuan Qu Street, Nan-Kang, Taipei 11503, Taiwan, R.O.C Tel: Fax: medical@comdek.com

2 Dear Customer, Thank you for purchasing the Comdek MD-680P Portable Pulse Oximeter. This fully featured unit will provide you the satisfactory in the performance and quality. If you have any questions regarding to this unit or owner s manual, please contact Comdek Service Dept. medical@comdek.com, or call , or fax to It shall be grateful if you could also fill out the form of customer s information, and send it back for our record. The feedback will help us to do the better service to you. If you have any questions, please do not hesitate to contact the nearest distributors or COMDEK directly. Sincerely Yours, Comdek Industrial Corporation Customer Service Dept.

3 CONTENTS CHAPTER ONE Introduction.. 1 Features 3 General Specification... 4 CHAPTER TWO Screen Panel Display 5 Signal Description Power Requirement.. 7 Operation Steps 8 Accessory. 8

4 CHAPTER THREE Things to Note Warranty Information.. 11 Please read carefully before use. Type BF equipment

5 Introduction The Pulse Oximeters non-invasively monitor the oxygen saturation (expressed as percentage of decimal) of arterial hemoglobin by measuring light absorbance changes resulting from arterial blood flow pulsation. Their use allows continuous and instantaneous monitoring of oxygenation; can provide early detection of hypoxia before other signs such as cyanosis, tachycardia, or bradycardia are observed; and may reduce the frequency of arterial puncture and laboratory blood gas analysis. Comdek palm oximeter is a non-invasively measurement to the SpO 2 and Pulse Rate. It is a small and compact instrument for easy operating and carrying. It is very useful for personal home care spot-checking and short-term monitoring in clinics

6 It presents an optimal performance with easy one touch operation, and the auto power off with low power consumption saves the cost of the batteries. Furthermore, the clear LED digital display brings you an outstanding observation, and the built-in finger probe makes it easier for measuring and traveling

7 Features *Palm and compact design *Easy carry for spot-checking *Light and large LED display *Quick response of SpO 2 & Pulse Rate *Complete unit with build-in finger probe *SpO 2 and pulse signal indicator *With audio and mute function *Low power consumption *Auto power off *Low battery indication - 3 -

8 General Specification Display Light Large LED, SpO 2 Saturation, Pulse Rate, Low battery indicator SpO 2 Range, % % Accuracy, % ±1% Pulse Rate Range, bpm 30bpm to 250bpm Accuracy, % 1% of full scale Audio Pulse Rate Probe type With built-in Adult Finger Probe Operating Temperature 0 ~ 55 Power Management Power saving function with 1 minute Auto cut off Power Requirement 3 AAA Quick measurement 6~8 seconds Dimensions, mm 90 x 62 x 22mm Weight, g 90 g (Net) Safety CE 0434 (Approved #98-OSL-SD-0401) - 4

9 CHAPTER TWO Screen Panel Display Finger Sensor Mute / Sound SpO 2 / Pulse Signal Indicator Low Battery Indicator SpO 2 Display / % Power Switch Pulse rate Display/ bpm Battery Cover - 5 -

10 Signal Description SpO 2 %: the saturation of Oxygen Pulse/min: the pulse rate per minute SpO 2 indicator: when the light is not on, it means the device is still on detecting. When the light is flashing, it means the measuring result is acceptable. Low battery indicator: when the light is on, it means the power is weak. The power will last for about 30 minutes. Pot: the finger is out of contact with the sensor - 6 -

11 Power Requirement Please use 3 pcs AAA batteries. (For best results, please use the alkaline battery) Warning: Please use the good quality batteries to avoid the chemical leakage, and damage the instrument. (The warranty will not cover this kind of damage). Do not dispose of empty batteries in household waste; take them to local special collection sites

12 Operation Steps 1. Open the battery cover at the bottom. 2. Insert 3 pcs AAA batteries. 3. Press the power button. 4. Insert a finger into the sensor clip 5. In the normal condition, after 6-8 seconds, the acceptable measuring results will show on the screen. The indicator of SpO 2 will flash with beep sound. 6. Press mute button to turn off the beep sound if it is necessary to be silent. 7. Finish the measuring, press power button to switch off the power. 8. If it is not in detecting state, the instrument will be auto power off in one minute. Accessory 1. Carrying bag 2. 3 x AAA batteries 3. Owner s manual - 8 -

13 Things to Note 1. Please handling with care, do not drop it. 2. Avoid scraping the sensor 3. Do not store the device in the hot and humid place. 4. Wipe away nail polish and dust on the finger before measuring. 5. If the instrument is not using for long period of time, please take the batteries out. 6. Only using soft clean cloth to wipe off the surface of the device 7. Please using alcohol to clean the finger sensor if needed - 9 -

14 Europe Representative: Comdek Computer System Schwendistrasse 32, Ch-8486 Rikon, Switzerland

15 Warranty Information Thank you for buying Comdek product, and we will offer one-year warranty. Please keep the following warranty to be the evidence of after service. Date Purchased or Received Model No.: Product Serial No.: User Name Information: Mr./Ms. Company Name: Street Address: City: Country: Zip: Telephone Number: Fax Number: Suggestion: